Before you begin… make sure that any existing firewall software/devices are disabled and/or shutdown before beginning installation of your new d-link di-704p broadband router. • di-704p broadband router with print server • user’s manual • quick install guide • power adapter • cat-5 utp cable • power...
First, plug in the power supply as shown. Plug the other end of the power supply into the power source. Flip the power toggle switch to the on position. (during a self-test phase, the indicator lights will flash briefly. At the end of the self-test, the m1 indicator light will flash continuously to ...
Make sure that tcp/ip protocol has been installed in your computer. Next, set the tcp/ip protocol to “obtain an ip address automatically” by doing the following: • go to start>settings • select “control panel” • double-click the “network” icon • select the tcp/ip line that includes the name of your ...
• use the “pull-down menu” on this screen to display the ethernet card that is installed in your computer and connected to the di- 704p. The ip address (for the ethernet network adapter) that appears in this window must be between 192.168.0.2 and 192.168.0.254 in order to configure the di-704p. • if...
Type “admin” in the “system password” field. Click on “log in” click on “setup” -5- configuring the di-704p with the web browser.
Click “change” (please see separate instructions below for dsl and cable users.) for dsl users: select “ppp over ethernet” if you are using a pppoe client to connect to your dsl provider (contact your dsl provider if you are uncertain.) -6- configuring the di-704p with the web browser.
For dsl users (continued): enter the pppoe account and password that your isp assigned to you. Leave the password field blank if you do not want to change the password. Input the pppoe service name if your isp requires it. Set the maximum idle time. (entering a value of “0” will disable this feature...
For cable users: select “dynamic ip address.” click “save.” enter the “host name” given to you by your cable provider (for example, “@home.”) for information on configuring a back-up dial-up modem, please see the “configuration” section of your user’s manual. Click “save” after you have input the in...
To check the connection, open the web browser and go to your favorite website. If you are unable to browse, please do the following: 1. Refer to appendix b to check your connection. 2. Use “help” on the main menu. 3. Refer to the troubleshooting section in the user’s manual. Your di-704p ethernet br...
Note: installing the print server software is only necessary if you plan to use the print server function of the d-link di-704p. If you choose to use the print server function, plug the printer cable from your printer into the printer port on the di-704p, if you have not already done so. Turn “on” t...
To select the default folder, click “next” note: it is recommended that you click “next” in the above window. However, if necessary, click “browse” to select an alternate folder. When this window is displayed, click “finish,” to complete the setup. -11- print server installation.
Select “yes, i want to restart my computer.” click “ok” after the computer has restarted, the print server software installation is complete. Note: if your printer is not installed, go to start>settings>printers. Double click on the “add printer” icon. Follow the “add printer wizard.” when requested...
Choose the “details” tab. (in windows 2000 or nt, choose the “ports” tab.) at the “add port” pull-down menu, choose “d-link lpt port (print server.)” please make sure the proper printer driver is selected. Click “port settings.” (for windows 2000/nt users: click “configure port.”) -13- configuring y...
Type in the “ip address” of the di-704p. Click “ok” in the previous window, make sure the settings are correct. Click “ok” you have completed configuring your printer. Go to start>settings>control panel double-click the “network” icon. Under the “configuration” tab highlight the “tcp/ip” line that i...
To manually input the ip address, please do the following: in the “tcp/ip properties” window, under the “ip address” tab, select “specify an ip address.” the default ip address of this product is 192.168.0.1 please use 192.168.0.Xxx (where “xxx” is a number between 2 and 99) to input into the “ip ad...
From the desktop, go to start>run type “command” in the box. Click “ok” the following ms-dos prompt window will appear. Type “ping 192.168.0.1” after the prompt. This is the ip address of the lan port of the broadband router. Hit “enter” you have a successful connection if the window displays four r...
Building networks for people printed in taiwan.
