- DL manuals
- D-Link
- Switch
- xStack DES-3200 Series
- Reference Manual
D-Link xStack DES-3200 Series Reference Manual - Asic
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch CLI Reference Manual
162
18
B
ASIC
IP
C
OMMANDS
The Basic IP interface commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the
following table:
Command
Parameters
config ipif
[System] [ { ipaddress 32> | state [enable | disable] }(1) | bootp | dhcp | dhcp_option12 [ hostname disable ] ] | ipv6 ipv6address show ipif enable autoconfig* disable autoconfig Each command is listed, in detail, in the following sections: *See Switch Utility Commands for descriptions of all autoconfig commands.
Summary of xStack DES-3200 Series
Page 1
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual ® cli reference manual product model : des-3200 series layer 2 managed ethernet switch release 1.21.
Page 2
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual information in this document is subject to change without notice. © 2010 d-link corporation. All rights reserved. Reproduction in any manner whatsoever without the written permission of d-link corporation is strictly forbid...
Page 3: Table of Contents
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual table of contents introduction .........................................................................................................................................................1 using the console cli ..................
Page 4
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual access control list (acl) commands .....................................................................................................210 time range commands ..................................................................
Page 5
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual dos prevention commands ...........................................................................................................................377 ip-mac-port binding commands ..............................................
Page 6: Ntroduction
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 1 1 i ntroduction the switch can be managed through the switch’s serial port, telnet, or the web-based management agent. The command line interface (cli) can be used to configure and manage the switch via the serial port or...
Page 7
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 2 the switch’s mac address can also be found in the web management program on the switch information (basic settings) window in the configuration folder. The ip address for the switch must be set before it can be managed wi...
Page 8: Sing The
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 3 2 u sing the c onsole cli the switch supports a console management interface that allows the user to connect to the switch’s management agent via a serial port and a terminal or a computer running a terminal emulation pro...
Page 9
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 4 .. ? Cable_diag ports clear clear address_binding dhcp_snoop binding_entry ports clear arptable clear counters clear dos_prevention counters clear fdb clear igmp_snooping data_driven_group clear log clear mac_based_access...
Page 10
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 5 des-3200-28:4#config account command: config account next possible completions: des-3200-28:4#config account command: config account next possible completions: des-3200-28:4# figure 2 - 4. Using the up arrow to re-enter a...
Page 11
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 6 des-3200-28:4#show command: show next possible completions: 802.1p 802.1x access_profile account acct_client address_binding arp_spoofing_prevention auth_session_statistics auth_statistics authen authen_enable authen_logi...
Page 12: Ommand
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 7 3 c ommand s yntax the following symbols are used to describe how command entries are made and values and arguments are specified in this manual. Note: all commands are case-sensitive. Be sure to disable caps lock or any ...
Page 14
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 9 multiple page display control keys displays the next page. Space stops the display of remaining pages when multiple pages are to be displayed. Ctrl+c stops the display of remaining pages when multiple pages are to be disp...
Page 15: Asic
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 10 4 b asic s witch c ommands the basic switch commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters enable password encryption disable pa...
Page 16
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 11 enable password encryption used to enable password encryption on a user account. Purpose enable password encryption syntax the user account configuration information will be stored in the configuration file, and can be a...
Page 19
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 14 show account used to display user accounts. Purpose show account syntax this command is used to display all user accounts created on the switch. Up to eight user accounts can exist at one time. Description none. Paramete...
Page 20
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 15 show session used to display a list of currently logged-in users. Purpose show session syntax this command is used to display a list of all the users that are logged-in at the time the command is issued. Description none...
Page 21
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 16 show switch used to display general information about the switch. Purpose show switch syntax this command is used to display information about the switch. Description none. Parameters none. Restrictions example usage: to...
Page 22
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 17 show serial_port used to display the current serial port settings. Purpose show serial_port syntax this command is used to display the current serial port settings. Description none. Parameters none restrictions example ...
Page 24
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 19 enable clipaging used to pause the scrolling of the console screen when a command displays more than one page. Purpose enable clipaging syntax this command is used when issuing a command which causes the console screen t...
Page 25
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 20 enable telnet used to enable communication with and management of the switch using the telnet protocol. Purpose enable telnet {} syntax this command is used to enable the telnet protocol on the switch. The user can speci...
Page 26
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 21 telnet used to telnet another device on the network. Purpose telnet {tcp_port } syntax this command is used to connect to another device’s management through telnet. Description parameters enter the ip address of the dev...
Page 27
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 22 disable web used to disable the http-based management software on the switch. Purpose disable web syntax this command disables the web-based management software on the switch. Description none. Parameters only administra...
Page 28
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 23 to save the switch’s current log to non-volatile ram: des-3200-28:4#save log command: save log saving all log information to nv-ram...... Done. Success. Des-3200-28:4# to save the switch’s the current configuration and l...
Page 30
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 25 to restore all of the switch’s parameters to their default values and have the switch save and reboot: des-3200-28:4#reset system command: reset system are you sure you want to proceed with system reset, save and reboot?...
Page 33
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 28 enable jumbo_frame used to enable jumbo frame. Purpose enable jumbo_frame syntax this command is used to configure the jumbo frame setting as enable. Description none. Parameters only administrator-level users can issue ...
Page 34
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 29 show jumbo_frame used to display the current configuration of jumbo frame. Purpose show jumbo_frame syntax this command is used to display the current configuration of the jumbo frame setting. Description none. Parameter...
Page 35: Odify
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 30 5 m odify b anner and p rompt c ommands the modify banner and prompt commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters config comma...
Page 36
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 31 config greeting _message used to configure the login banner (greeting message). Purpose config greeting _message {default} syntax users can use this command to modify the login banner (greeting message). Description defa...
Page 37
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 32 show greeting_message used to view the currently configured greeting message configured on the switch. Purpose show greeting_message syntax this command is used to view the currently configured greeting message on the sw...
Page 40
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 35 des-3200-28:4#config ports 25-28 speed 10_full state enable command: config ports 25-28 speed 10_full state enable warning: for combo ports, the configuration is set to medium_type copper success. Des-3200-28:4# show por...
Page 41
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 36 example usage: to display the configuration of all ports on a standalone switch, with description: des-3200-28:4#show ports description command: show ports description port state/ settings connection address mdi speed/du...
Page 44
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 39 delete port_security_entry used to delete a port security entry by mac address, port number and vlan id. Purpose delete port_security_entry vlan_name mac_address port syntax this command is used to delete a single, previ...
Page 45
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 40 clear port_security_entry used to clear mac address entries learned from a specified port for the port security function. Purpose clear port_security_entry ports syntax this command is used to clear mac address entries w...
Page 46
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 41 show port_security used to display the current port security configuration. Purpose show port_security {ports } syntax this command is used to display port security information of the switch’s ports. The information disp...
Page 47
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 42 enable port_security trap_log used to enable the trap log for port security. Purpose enable port_security trap_log syntax this command, along with the disable port_security trap_log, will enable the sending of log messag...
Page 48: Etwork
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 43 8 n etwork m anagement (snmp) c ommands the switch supports the simple network management protocol (snmp) versions 1, 2c, and 3. Users can specify which version of the snmp users want to use to monitor and control the sw...
Page 51
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 46 example usage: to create an snmp user on the switch: des-3200-28:4#create snmp user dlink default encrypted by_password auth md5 knickerbockers priv none command: create snmp user dlink default encrypted by_password auth...
Page 52
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 47 show snmp user used to display information about each snmp username in the snmp group username table. Purpose show snmp user syntax this command is used to display information about each snmp username in the snmp group u...
Page 55
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 50 example usage: to display snmp view configuration: des-3200-28:4#show snmp view command: show snmp view vacm view table settings view name subtree view type -------------------- ----------------------- ---------- restric...
Page 56
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 51 example usage: to create the snmp community string “dlink”: des-3200-28:4#create snmp community dlink view readview read_write command: create snmp community dlink view readview read_write success. Des-3200-28:4# delete ...
Page 57
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 52 example usage: to display the currently entered snmp community strings: des-3200-28:4#show snmp community command: show snmp community snmp community table community name view name access right ------------------ -------...
Page 58
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 53 show snmp engineid used to display the identification of the snmp engine on the switch. Purpose show snmp engineid syntax this command is used to display the identification of the snmp engine on the switch. Description n...
Page 60
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 55 example usage: to create an snmp group named “sg1:” des-3200-28:4#create snmp group sg1 v3 noauth_nopriv read_view v1 write_view v1 notify_view v1 command: create snmp group sg1 v3 noauth_nopriv read_view v1 write_view v...
Page 61
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 56 example usage: to display the currently configured snmp groups on the switch: des-3200-28:4#show snmp groups command: show snmp groups vacm access table settings group name : group3 readview name : readview writeview nam...
Page 63
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 58 delete snmp host used to remove a recipient of snmp traps generated by the switch’s snmp agent. Purpose delete snmp [host ] syntax this command is used to delete a recipient of snmp traps generated by the switch’s snmp a...
Page 65
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 60 example usage: to delete a trusted host with an ip address 10.48.74.121: des-3200-28:4#delete trusted_host ipaddr 10.48.74.121 command: delete trusted_host ipaddr 10.48.74.121 success. Des-3200-28:4# to delete a trusted ...
Page 66
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 61 example usage: to display the list of trust hosts: des-3200-28:4#show trusted_host command: show trusted_host management stations ip address/netmask ----------------------- 10.53.13.94/32 total entries: 1 des-3200-28:4# ...
Page 69
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 64 config snmp system_contact used to enter the name of a contact person who is responsible for the switch. Purpose config snmp system_contact {} syntax this command is used to enter the name and/or other information to ide...
Page 70
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 65 config snmp system_name used to configure the name for the switch. Purpose config snmp system_name {} syntax this command is used to configure the name of the switch. Description parameters a maximum of 128 characters is...
Page 71
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 66 disable rmon used to disable rmon on the switch. Purpose disable rmon syntax this command is used, in conjunction with the enable rmon command above, to enable and disable remote monitoring (rmon) on the switch. Descript...
Page 74
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 69 des-3200-28:4#download cfg_fromtftp 10.48.74.121 c:\cfg\setting.Txt command: download cfg_fromtftp 10.48.74.121 c:\cfg\setting.Txt connecting to server................... Done. Download configuration................. Don...
Page 76
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 71 show firmware information used to display the firmware section information. Purpose show firmware information syntax this command is used to display the firmware section information. Description none. Parameters none res...
Page 78
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 73 example usage: to view the current configuration settings: des-3200-28:4#show config current_config command: show config current_config ------------------------------------------------------------------- # des-3200-28 co...
Page 80
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 75 enable autoconfig used to activate the auto configuration function for the switch. This will load a previously saved configuration file for current use. Purpose enable autoconfig syntax when autoconfig is enabled on the ...
Page 81
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 76 des-3200-28 fast ethernet switch command line interface firmware: build 1.10.B014 copyright(c) 2009 d-link corporation. All rights reserved. Des-3200-28:4# des-3200-28:4# des-3200-28:4#download cfg_fromtftp 10.41.44.44 c...
Page 82
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 77 disable autoconfig use this to deactivate auto configuration from dhcp. Purpose disable autoconfig syntax this command is used to instruct the switch not to accept auto configuration instruction from the dhcp server. Thi...
Page 83
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 78 ping used to test the connectivity between network devices. Purpose ping {times } {size } {timeout } syntax the command is used to send internet control message protocol (icmp) echo messages to a remote ip address. The r...
Page 85
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 80 traceroute used to trace the routed path between the switch and a destination endstation. Purpose traceroute {ttl } {port } {timeout } {probe } syntax this command is used to trace the routed path between the switch and ...
Page 87: Etwork
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 82 10 n etwork m onitoring c ommands the network monitoring commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters show packet ports show e...
Page 88
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 83 show packet ports used to display stats about packets sent and received by the switch. Purpose show packet ports syntax this command is used to display statistics about packets sent and received by ports specified in the...
Page 89
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 84 show error ports used to display the error statistics for a range of ports. Purpose show error ports syntax this command is used to display all of the packet error statistics collected and logged by the switch for a give...
Page 91
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 86 to display the current flash memory utilization: des-3200-28:4#show utilization flash command: show utilization flash flash memory utilization : total flash : 16,384 kb used flash : 7,371 kb utilization : 44% ctrl+c esc ...
Page 92
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 87 clear counters used to clear the switch’s statistics counters. Purpose clear counters {ports } syntax this command is used to clear the counters used by the switch to compile statistics. Description parameters specifies ...
Page 93
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 88 show log used to display the switch history log. Purpose show log {index } syntax this command is used to display the contents of the switch’s history log. Description parameters index this command will display the histo...
Page 94
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 89 disable syslog used to disable the system log to be sent to a remote host. Purpose disable syslog syntax this command is used to disable the system log to be sent to a remote host. Description none. Parameters only admin...
Page 96
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 91 create syslog host 0 kernel messages 1 user-level messages 2 mail system 3 system daemons 4 security/authorization messages 5 messages generated internally by syslog 6 line printer subsystem 7 network news subsystem 8 uu...
Page 97
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 92 example usage: to create a syslog host: des-3200-28:4#create syslog host 1 ipaddress 10.68.88.1 severity all facility local0 command: create syslog host 1 ipaddress 10.68.88.1 severity all facility local0 success. Des-32...
Page 98
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 93 numerical facility code parameters 0 kernel messages 1 user-level messages 2 mail system 3 system daemons 4 security/authorization messages 5 messages generated internally by syslog 6 line printer subsystem 7 network new...
Page 99
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 94 example usage: to configure a syslog host: des-3200-28:4#config syslog host 1 severity all facility local0 command: config syslog host all severity all facility local0 success. Des-3200-28:4# to configure a syslog host f...
Page 100
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 95 show syslog host used to display the syslog hosts currently configured on the switch. Purpose show syslog host {} syntax this command is used to display the syslog hosts that are currently configured on the switch. Descr...
Page 102
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 97 delete ipif used to delete an interface. Purpose delete ipif [system] [ipv6address ] syntax this command is used to delete an interface. The system interface cannot be deleted. By using this command, an ipv6 address can ...
Page 103
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 98 disable ipif_ipv6_link_local_auto used to disable the auto configuration of a link local address when no ipv6 address is configured. Purpose disable ipif_ipv6_link_local_auto [system] syntax this command is used to disab...
Page 104: Ultiple
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 99 11 m ultiple s panning t ree p rotocol (mstp) c ommands this switch supports three versions of the spanning tree protocol; 802.1d stp, 802.1w rapid stp and 802.1s mstp. Multiple spanning tree protocol, or mstp, is a stan...
Page 106
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 101 enable stp used to globally enable stp on the switch. Purpose enable stp syntax this command is used to globally enable the spanning tree protocol on the switch. Description none. Parameters only administrator-level use...
Page 110
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 105 example usage: to configure stp with path cost auto, hellotime 2 seconds, migration enable, and state enable for ports 1 to 2: des-3200-28:4#config stp ports 1-2 externalcost auto hellotime 2 migrate yes state enable co...
Page 112
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 107 delete stp instance_id used to delete a stp instance id from the switch. Purpose delete stp instance_id syntax this command is used to delete a previously configured stp instance id from the switch. Description paramete...
Page 115
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 110 show stp used to display the switch’s current stp configuration. Purpose show stp syntax this command is used to display the switch’s current stp configuration. Description none parameters none. Restrictions example usa...
Page 116
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 111 status 2 : stp enabled for rstp des-3200-28:4#show stp command: show stp stp bridge global settings -------------------------- stp status : enabled stp version : rstp max age : 20 hello time : 2 forward delay : 15 max h...
Page 117
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 112 show stp ports used to display the switch’s current stp ports configuration. Purpose show stp ports {} {instance } syntax this command is used to display the stp port settings for a specified port or group of ports. Des...
Page 118
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 113 show stp instance used to display the switch’s stp instance configuration purpose show stp instance {} syntax this command is used to display the switch’s current stp instance settings and the stp instance operational s...
Page 119
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 114 show stp mst_config_id used to display the mstp configuration identification. Purpose show stp mst_config_id syntax this command is used to display the switch’s current mstp configuration identification. Description non...
Page 120: Orwarding
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 115 12 f orwarding d atabase c ommands the layer 2 forwarding database commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters create fdb po...
Page 121
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 116 create fdb used to create a static entry in the unicast mac address forwarding table (database). Purpose create fdb port syntax this command is used to make an entry in the switch’s unicast mac address forwarding databa...
Page 123
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 118 example usage: to set the fdb aging time: des-3200-28:4#config fdb aging_time 300 command: config fdb aging_time 300 success. Des-3200-28:4# delete fdb used to delete an entry to the switch’s forwarding database. Purpos...
Page 125
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 120 example usage: to display the multicast mac address table: des-3200-28:4#show multicast_fdb vlan default command: show multicast_fdb vlan default vlan name : default mac address : 01-00-5e-00-00-00 egress ports : 1-5 mo...
Page 126
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 121 example usage: to display unicast mac address table: des-3200-28:4#show fdb command: show fdb unicast mac address ageing time = 300 vid vlan name mac address port type ---- ------------------------ ----------------- ---...
Page 127
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 122 show multicast port_filtering_mode used to show the multicast packet filtering mode for ports. Purpose show multicast port_filtering_mode syntax this command is used to display the current multicast packet filtering mod...
Page 128: Acket
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 123 13 p acket s torm c ontrol c ommands on a computer network, packets such as multicast packets and broadcast packets continually flood the network as normal procedure. At times, this traffic may increase due to a malicio...
Page 129
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 124 config traffic control used to configure broadcast/multicast/unicast packet storm control. The software mechanism is provided to monitor the traffic rate in addition to the hardware storm control mechanism previously pr...
Page 130
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 125 config traffic control only administrator-level users can issue this command. Restrictions example usage: to configure traffic control and enable broadcast storm control for ports 1 to 12: des-3200-28:4#config traffic c...
Page 132: Ommands
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 127 14 q o s c ommands the switch supports 802.1p priority queuing. The switch has four priority queues. These priority queues are numbered from 3 (class 3) — the highest priority queue — to 0 (class 0) — the lowest priorit...
Page 134
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 129 show bandwidth_control used to display the bandwidth control table. Purpose show bandwidth_control {} syntax this command is used to display the current bandwidth control configuration on the switch, on a port-by-port b...
Page 135
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 130 config scheduling used to configure the traffic scheduling mechanism for each cos queue. Purpose config scheduling weight syntax the switch contains four hardware priority queues. Incoming packets must be mapped to one ...
Page 136
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 131 show scheduling used to display the currently configured traffic scheduling on the switch. Purpose show scheduling syntax this command is used to display the current traffic scheduling mechanisms in use on the switch. D...
Page 137
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 132 example usage: to configure the traffic scheduling mechanism for each qos queue: des-3200-28:4#config scheduling_mechanism strict command: config scheduling_mechanism strict success. Des-3200-28:4# show scheduling_mecha...
Page 138
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 133 config 802.1p user_priority used to map the 802.1p user priority of an incoming packet to one of the four hardware queues available on the switch. Purpose config 802.1p user_priority syntax this command is used to confi...
Page 139
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 134 show 802.1p user_priority used to display the current mapping between an incoming packet’s 802.1p priority value and one of the switch’s four hardware priority queues. Purpose show 802.1p user_priority syntax this comma...
Page 140
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 135 config 802.1p default_priority used to configure the 802.1p default priority settings on the switch. If an untagged packet is received by the switch, the priority configured with this command will be written to the pack...
Page 141
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 136 show 802.1p default_priority used to display the currently configured 802.1p priority value that will be assigned to an incoming, untagged packet before being forwarded to its destination. Purpose show 802.1p default_pr...
Page 143
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 138 show cos mapping used to show cos mapping. Purpose show cos mapping {port } syntax this command is used to display information regarding cos mapping enabled ports and their mapping method. Description parameters specifi...
Page 144
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 139 config cos tos value used to map the tos value in the ip header of incoming packets to one of the four hardware queues available on the switch. Purpose config cos tos value [class ] syntax this command is used to config...
Page 145
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 140 config dscp_mapping used to map the dscp value in the ip header of incoming packet to one of the four hardware queues available on the switch. Purpose config dscp_mapping dscp_value [class 3>] syntax this command is use...
Page 146
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 141 show dscp_mapping used to show dscp value map to traffic class. Purpose show dscp_mapping {dscp_value } syntax this command displays the information for dscp mapping to traffic class. Description parameters the dscp val...
Page 148
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 143 des-3200-28:4#config mirror port 1 add source ports 2-7 both command: config mirror port 1 add source ports 2-7 both success. Des-3200-28:4# example usage: to delete the mirroring ports: des-3200-28:4#config mirror port...
Page 149
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 144 to disable mirroring configurations: des-3200-28:4#disable mirror command: disable mirror success. Des-3200-28:4# show mirror used to show the current port mirroring configuration on the switch. Purpose show mirror synt...
Page 152
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 147 config vlan only administrator-level users can issue this command. Restrictions.
Page 153
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 148 example usage: to add 4 through 8 as tagged ports to the vlan v1: des-3200-28:4#config vlan v1 add tagged 4-8 command: config vlan v1 add tagged 4-8 success. Des-3200-28:4# to delete ports from a vlan: des-3200-28:4#con...
Page 154
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 149 example usage: to delete a vlan id on the switch: des-3200-28:4#delete vlan vlanid 5 command: delete vlan vlanid 5 success des-3200-28:4# config vlan vlanid used to add additional ports to a previously configured vlan. ...
Page 155
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 150 enable pvid auto_assign used to enable auto-assignment of pvid. Purpose enable pvid auto_assign syntax this command is used to enable auto-assignment of pvid. Description none. Parameters only administrator-level users ...
Page 156
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 151 example usage: to display the pvid auto-assignment state: des-3200-28:4#show pvid auto_assign command: show pvid auto_assign pvid auto-assignment: enabled des-3200-28:4# config gvrp used to configure gvrp on the switch....
Page 157
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 152 enable gvrp used to enable gvrp on the switch. Purpose enable gvrp syntax this command, along with disable gvrp below, is used to enable and disable gvrp on the switch, without changing the gvrp configuration on the swi...
Page 158
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 153 show vlan vlan. Parameters the vlan name of the vlan for which to display a summary of settings. Vlanid specifies a range of multiple vlan ids to be displayed. Ports specifies a port or range of ports that will be displ...
Page 159
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 154.
Page 160
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 155 example usage: to display gvrp port status: des-3200-28:4#show gvrp 1-10 command: show gvrp 1-10 global gvrp : disabled port pvid reassigned gvrp ingress acceptable frame type pvid state checking ---- ---- ---------- --...
Page 161: Ink
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 156 17 l ink a ggregation c ommands the link aggregation commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters create link_aggregation gro...
Page 162
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 157 des-3200-28:4#create link_aggregation group_id 1 command: create link_aggregation group_id 1 success. Des-3200-28:4# delete link_aggregation group_id used to delete a previously configured link aggregation group. Purpos...
Page 163
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 158 des-3200-28:4#config link_aggregation group_id 1 master_port 1 ports 1-4 command: config link_aggregation group_id 1 master_port 1 ports 1-4 success. Des-3200-28:4# config link_aggregation algorithm used to configure th...
Page 164
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 159 show link_aggregation by the algorithm in use by that switch. None. Restrictions.
Page 165
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 160 example usage: to display link aggregation configuration: des-3200-28:4#show link_aggregation command: show link_aggregation link aggregation algorithm = mac-source group id : 1 type: : trunk master port : member port :...
Page 166
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 161 show lacp_ports used to display current lacp port mode settings. Purpose show lacp_ports {} syntax this command is used to display the lacp mode settings as they are currently configured. Description parameters specifie...
Page 167: Asic
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 162 18 b asic ip c ommands the basic ip interface commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters config ipif [system] [ { ipaddress...
Page 169
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 164 example usage: to configure an interface’sipv4 network address: des-3200-28f:4# config ipif system ipaddress 10.48.74.122/8 command: config ipif system ipaddress 10.48.74.122/8 success. Des-3200-28f:4# to configure an i...
Page 170
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 165 example usage: to display ip interface settings: des-3200-28f:4# show ipif command: show ipif ip interface settings interface name ip address : system subnet mask : 192.168.1.66 (manual) vlan name : 255.0.0.0 admin. Sta...
Page 171
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 166 enable autoconfig used to activate the auto configuration function for the switch. This will load a previously saved configuration file for current use. Purpose enable autoconfig syntax when autoconfig is enabled on the...
Page 172
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 167 example usage: to enable auto configuration on the switch: des-3200-28:4#disable autoconfig command: disable autoconfig success. Des-3200-28:4#.
Page 175
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 170 config igmp_snooping querier value of the robustness variable. • by default, the robustness variable is set to 2. You might want to increase this value if you expect a subnet to be lossy. Last_member_query_interval the ...
Page 176
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 171 des-3200-28:4#config router_ports default add 1-10 command: config router_ports default add 1-10 success. Des-3200-28:4# config router_ports_forbidden used to configure ports as forbidden router ports. Purpose syntax co...
Page 177
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 172 des-3200-28:4#enable igmp_snooping command: enable igmp_snooping success. Des-3200-28:4#.
Page 178
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 173 disable igmp_snooping used to disable igmp snooping on the switch. Purpose disable igmp_snooping {forward_mcrouter_only} syntax this command is used to disable igmp snooping on the switch. If forward_mcrouter_only is sp...
Page 179
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 174 example usage: to show igmp snooping: des-3200-28:4#show igmp_snooping command: show igmp_snooping igmp snooping global state : disabled multicast router only : disabled data driven learning max entries : 56 vlan name :...
Page 180
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 175 example usage: to display the router ports. Des-3200-28:4#show router_ports command: show router_ports vlan name : default static router port : dynamic router port: forbidden router port: total entries: 1 des-3200-28:4#...
Page 182
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 177 example usage: to configure igmp snooping data driven learning’s maximum learned entry value: des-3200-28:4# config igmp_snooping data_driven_learning max_learned_entry 1 command: config igmp_snooping data_driven_learni...
Page 183
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 178 show igmp_snooping host specifies the ip address of a group to display the host information. Only administrator-level users can issue this command. Restrictions example usage: to display igmp snooping fast leave hosts: ...
Page 184
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 179 example usage: to enable igmp access control for all ports: des-3200-28:4# config igmp access_authentication ports all state enable command: config igmp access_authentication ports all state enable success. Des-3200-28:...
Page 186
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 181 config dhcp_relay add ipif used to add an ip destination address to the switch's dhcp/bootp relay table. Purpose config dhcp_relay add ipif [system] syntax this command is used to add an ip address as a destination to f...
Page 188
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 183 config dhcp_relay option_82 check enable – when the field is toggled to enable, the relay agent will check the validity of the packet’s option 82 field. If the switch receives a packet that contains the option 82 field ...
Page 190
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 185.
Page 191
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 186 example usage: to show the dhcp relay configuration: des-3200-28:4#show dhcp_relay command: show dhcp_relay dhcp/bootp relay status : disabled dhcp/bootp hops count limit : 4 dhcp/bootp relay time threshold : 0 dhcp rel...
Page 192
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 187 disable dhcp_relay disable dhcp_relay syntax this command is used to disable the dhcp/bootp relay function on the switch. Description none. Parameters only administrator-level users can issue this command. Restrictions ...
Page 193: 802.1X
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 188 21 802.1x c ommands the switch implements ieee 802.1x port-based and host-based access control. This mechanism is intended to allow only authorized users, or other network devices, access to network resources by establi...
Page 194
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 189 command parameters show acct_client create 802.1x user delete 802.1x user show 802.1x user each command is listed, in detail, in the following sections: enable 802.1x used to enable the 802.1x server on the switch. Purp...
Page 196
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 191 to display the 802.1x authentication states: des-3200-28:4#show 802.1x auth_configuration ports 1 command: show 802.1x auth_configuration ports 1 802.1x : enabled authentication mode : port_based authentication protocol...
Page 197
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 192 to display the 802.1x authentication state for port-based 802.1x: des-3200-28:4#show 802.1x auth_state command: show 802.1x auth_state port auth pae state backend state port status ------ -------------- ------------- --...
Page 198
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 193 example usage: to display the 802.1x authentication state for host-based 802.1x: des-3200-28:4#show 802.1x auth_state command: show 802.1x auth_state port number : 1 index mac address auth pae state backend state port s...
Page 200
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 195 config 802.1x auth_parameter ports used to configure the 802.1x authentication parameters on a range of ports. The default parameter will return all ports in the specified range to their default 802.1x settings. Purpose...
Page 201
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 196 example usage: to configure 802.1x authentication parameters for ports 1 to 20: des-3200-28:4#config 802.1x auth_parameter ports 1–20 direction both command: config 802.1x auth_parameter ports 1–20 direction both succes...
Page 202
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 197 example usage: to initialize the authentication state machine of all ports: des-3200-28:4# config 802.1x init port_based ports all command: config 802.1x init port_based ports all success. Des-3200-28:4# config 802.1x r...
Page 204
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 199 config radius delete used to delete a previously entered radius server configuration. Purpose config radius delete syntax this command is used to delete a previously entered radius server configuration. Description para...
Page 205
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 200 example usage: to configure the radius settings: des-3200-28:4#config radius 1 10.48.74.121 key dlink default command: config radius 1 10.48.74.121 key dlink default success. Des-3200-28:4# config radius parameter used ...
Page 206
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 201 example usage: to display radius settings on the switch: des-3200-28:4#show radius command: show radius timeout : 5 seconds retransmit : 2 index ip address auth-port acct-port status key number number ----- ------------...
Page 208
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 203 example usage: to configure the configurations for a previously created 802.1x guest vlan: des-3200-28:4#show 802.1x guest_vlan command: show 802.1x guest_vlan guest vlan settings ---------------------------------------...
Page 209
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 204 show acct_client used to display the current radius accounting client. Purpose show acct_client syntax this command is used to display the current radius accounting client currently configured on the switch. Description...
Page 210
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 205 show auth_client used to display the current radius authentication client. Purpose show auth_client syntax this command is used to display the current radius authentication client currently configured on the switch. Des...
Page 211
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 206 show auth_diagnostics used to display the current authentication diagnostics. Purpose show auth_diagnostics {ports [} syntax this command is used to display the current authentication diagnostics of the switch on a per ...
Page 212
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 207 show auth_session_statistics used to display the current authentication session statistics. Purpose show auth_session_statistics {ports } syntax this command is used to display the current authentication session statist...
Page 213
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 208 example usage: to display the current authentication statistics for port 1: des-3200-28:4#show auth_statistics ports 1 command: show auth_statistics ports 1 port number : 1 mac address: 00-00-07-5d-60-02 eapolframesrx 6...
Page 214
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 209 show 802.1x user used to display the 802.1x user accounts on the switch. Purpose show 802.1x user syntax this command is used to display the 802.1x port-based or host-based network access control local users currently c...
Page 215: Ccess
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 210 22 a ccess c ontrol l ist (acl) c ommands the switch implements access control lists that enable the switch to deny network access to specific devices or device groups based on ip settings and mac address. The access co...
Page 217
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 212 now that an access profile has been created, users must add the criteria the switch will use to decide if a given frame should be forwarded or filtered. We will use the config access_profile command to create a new rule...
Page 218
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 213 create access_profile source_ip_mask specifies an ip address mask for the source ip address. Destination_ip_mask specifies an ip address mask for the destination ip address. Dscp specifies that the switch will examine t...
Page 219
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 214 create access_profile offset can range from 0 up to 31. The offset reference can be either of the following: l2 – the offset will start counting from the byte after the end of the vlan tags (start of ether type). L3 – t...
Page 220
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 215 config access_profile used to configure an access profile on the switch and to define specific values that will be used to by the switch to determine if a given packet should be forwarded or filtered. Masks entered usin...
Page 221
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 216 config access_profile 802.1p specifies that the access profile will apply only to packets with this 802.1p priority value. Ethernet_type specifies that the access profile will apply only to packets with this hexadecimal...
Page 222
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 217 config access_profile source_ipv6_mask – specifies an ipv6 source address. Src_port_mask – specifies an ipv6 l4 (tcp/udp) source port submask. Dst_port_mask – specifies an ipv6 l4 (tcp/udp) destination port submask. Pac...
Page 223
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 218 config access_profile specified for all access profiles. Only administrator-level users can issue this command. Restrictions example usage: to configure the access profile with the profile id of 1 to filter frames on po...
Page 224
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 219 des-3200-28:4#show access_profile command: show access_profile access profile table ================================================================================ profile id: 101 type: ipv4 frame filter - icmp =======...
Page 225
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 220 create cpu access_profile header. Ip specifies that the switch will examine the ip fields in each frame’s header. Vlan specifies a vlan mask. Source_ip_mask specifies an ip address mask for the source ip address. Destin...
Page 226
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 221 create cpu access_profile address. Profile_id enter an integer between 1 and 3 that is used to identify the cpu access profile to be created with this command. Only administrator-level users can issue this command. Rest...
Page 228
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 223 config cpu access_profile field within each packet. Src_port specifies that the access profile will apply only to packets that have this tcp source port in their tcp header. Dst_port specifies that the access profile wi...
Page 229
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 224 example usage: to configure cpu access list entry: des-3200-28:4#config cpu access_profile profile_id 3 add access_id 1 ip vlan default source_ip 20.2.2.3 destination_ip 10.1.1.252 dscp 3 icmp type 11 code 32 port all d...
Page 230
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 225 des-3200-28:4#show cpu_access_profile command: show cpu_access_profile cpu interface filtering state: enabled access profile table ================================================================================ profile...
Page 231
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 226 disable cpu_interface_filtering used to disable cpu interface filtering on the switch. Purpose disable cpu_interface_filtering syntax this command is used, in conjunction with the enable cpu_interface_filtering command ...
Page 232: Ime
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 227 23 t ime r ange c ommands the time range commands are used in conjunction with the access profile commands listed in the previous chapter to determine a starting point and an ending point, based on days of the week, whe...
Page 233
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 228 config time_range fri would mean monday through friday). To specify a list of days in a week, separate the daylist using a comma, with no spaces (mon,tue,fri would mean monday, tuesday and friday). Delete – use this par...
Page 234: Afeguard
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 229 24 s afeguard e ngine c ommands periodically, malicious hosts on the network will attack the switch by utilizing packet flooding (arp storm) or other methods. These attacks may increase the cpu utilization beyond its ca...
Page 235
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 230 config safeguard_engine packets, until the storm has subsided. Fuzzy if selected, this function will instruct the switch to minimize the ip and arp traffic flow to the cpu by dynamically allotting an even bandwidth to a...
Page 236: Raffic
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 231 25 t raffic s egmentation c ommands traffic segmentation allows users to further sub-divide vlans into smaller groups of ports that will help to reduce traffic on the vlan. The vlan rules take precedence, and then the t...
Page 237
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 232 show traffic_segmentation used to display the current traffic segmentation configuration on the switch. Purpose show traffic_segmentation {} syntax this command is used to display the current traffic segmentation config...
Page 238: Ime and
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 233 26 t ime and sntp c ommands the simple network time protocol (sntp) (an adaptation of the network time protocol (ntp)) commands in the command line interface (cli) are listed (along with the appropriate parameters) in t...
Page 239
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 234 des-3200-28:4#config sntp primary 10.1.1.1 secondary 10.1.1.2 poll-interval 30 command: config sntp primary 10.1.1.1 secondary 10.1.1.2 poll-interval 30 success. Des-3200-28:4# show sntp used to display the sntp informa...
Page 240
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 235 des-3200-28:4#enable sntp command: enable sntp success. Des-3200-28:4# disable sntp to disable sntp server support. Purpose disable sntp syntax this command is used to disable sntp support. Sntp service must be separate...
Page 241
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 236 example usage: to manually set system time and date settings: des-3200-28:4#config time 30jun2003 16:30:30 command: config time 30jun2003 16:30:30 success. Des-3200-28:4# config time_zone used to determine the time zone...
Page 242
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 237 config dst disable disable the dst seasonal time adjustment for the switch. Repeating using repeating mode will enable dst seasonal time adjustment. Repeating mode requires that the dst beginning and ending date be spec...
Page 243
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 238 des-3200-28:4#config dst repeating s_week 2 s_day tue s_mth 4 s_time 15:00 e_week 2 e_day wed e_mth 10 e_time 15:30 offset 30 command: config dst repeating s_week 2 s_day tue s_mth 4 s_time 15:00 e_week 2 e_day wed e_mt...
Page 245
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 240 config arpentry above. Only administrator-level users can issue this command. Restrictions example usage: to configure a static arp entry for the ip address 10.48.74.12 and mac address 00:50:ba:00:07:36: des-3200-28:4#c...
Page 247
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 242 des-3200-28:4#show arpentry command: show arpentry arp aging time : 20 interface ip address mac address type ------------- --------------- ----------------- --------------- system 10.0.0.0 ff-ff-ff-ff-ff-ff local/broadc...
Page 248: Outing
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 243 28 r outing t able c ommands the routing table commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create iproute [default] {} delet...
Page 249
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 244 delete iproute used to delete a default ip route entry from the switch’s ip routing table. Purpose delete iproute [default] syntax this command is used to delete an existing default entry from the switch’s ip routing ta...
Page 250
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 245 create ipv6 neighbor_cache ipif used to add a static neighbor to an ipv6 interface. Purpose create ipv6 neighbor_cache ipif syntax this command is used to add a static neighbor to an ipv6 interface. Description paramete...
Page 252
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 247 example usage: to add the default static address 10.48.74.121, with a metric setting of 1, to the routing table: des-3200-28:4#create ipv6route default system 3ffc::1 command: create ipv6route default system 3ffc::1 suc...
Page 253
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 248 des-3200-28:4#show ipv6 nd ipif system command: show ipv6 nd ipif system interface name : system ns retransmit time : 0(ms) des-3200-28:4# show ipv6route used to display ipv6 routes. Purpose show ipv6route syntax this c...
Page 254
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 249 des-3200-28:4#config ipv6 nd ns ipif system retrans_time 10000 command: config ipv6 nd ns ipif system retrans_time 10000 success. Des-3200-28:4#.
Page 255: Mac
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 250 29 mac n otification c ommands the mac notification commands in the command line interface (cli) are listed, in the following table, along with their appropriate parameters. Command parameters enable mac_notification di...
Page 257
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 252 des-3200-28:4#config mac_notification ports 7 enable command: config mac_notification ports 7 enable success. Des-3200-28:4#.
Page 258
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 253 show mac_notification used to display the switch’s mac address table notification global settings. Purpose show mac_notification syntax this command is used to display the switch’s mac address table notification global ...
Page 259
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 254 des-3200-28:4#show mac_notification ports command: show mac_notification ports port # mac address table notification state ------ ------------------------------------ 1 disabled 2 disabled 3 disabled 4 disabled 5 disabl...
Page 260: Ccess
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 255 30 a ccess a uthentication c ontrol c ommands the tacacs / xtacacs / tacacs+ / radius commands allows secure access to the switch using the tacacs / xtacacs / tacacs+ / radius protocols. When a user logs in to the switc...
Page 261
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 256 the access authentication control commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters enable authen_policy disable authen_policy sho...
Page 262
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 257 command parameters enable admin config admin local_enable each command is listed, in detail, in the following sections. Enable authen_policy used to enable system access authentication policy. Purpose enable authen_poli...
Page 263
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 258 show authen_policy used to display the system access authentication policy status on the switch. Purpose show authen_policy syntax this command will show the current status of the access authentication policy on the swi...
Page 265
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 260 config authen_login the switch. Method_list_name – enter a previously implemented method list name defined by the user. The user may add one, or a combination of up to four of the following authentication methods to thi...
Page 266
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 261 delete authen_login method_list_name this command is used to delete a list for authentication methods for user login. Description parameters enter an alphanumeric string of up to 15 characters to define the given method...
Page 267
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 262 des-3200-28:4#show authen_login method_list_name zira command: show authen_login method_list_name zira method list name priority method name comment ---------------- --------- --------------- --------- zira 1 tacacs+ bu...
Page 268
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 263 config authen_enable administrator. A maximum of eight enable method lists can be implemented simultaneously on the switch. The sequence of methods implemented in this command will affect the authentication result. For ...
Page 269
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 264 config authen_enable server_group adding this parameter will require the user to be authenticated using a user-defined server group previously configured on the switch. Local_enable adding this parameter will require th...
Page 270
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 265 des-3200-28:4#delete authen_enable method_list_name permit command: delete authen_enable method_list_name permit success. Des-3200-28:4# show authen_enable used to display the method list of authentication methods for p...
Page 271
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 266 des-3200-28:4#show authen_enable all command: show authen_enable all method list name priority method name comment ---------------- -------- ------------- ------------------ permit 1 tacacs+ built-in group 2 tacacs buil...
Page 272
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 267 config authen application only administrator-level users can issue this command. Restrictions example usage: to configure the default method list for the web interface: des-3200-28:4#config authen application http login...
Page 273
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 268 create authen server_host tacacs/xtacacs/tacacs+/radius server host on a remote host. The tacacs/xtacacs/tacacs+/radius server host will then verify or deny the request and return the appropriate message to the switch. ...
Page 275
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 270 des-3200-28:4#config authen server_host 10.1.1.121 protocol tacacs+ port 4321 timeout 12 retransmit 4 command: config authen server_host 10.1.1.121 protocol tacacs+ port 4321 timeout 12 retransmit 4 success. Des-3200-28...
Page 276
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 271 show authen server_host ip address – the ip address of the authentication server host. Protocol – the protocol used by the server host. Possible results will include tacacs, xtacacs, tacacs+ or radius. Port – the virtua...
Page 277
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 272 des-3200-28:4#create authen server_group group_1 command: create authen server_group group_1 success. Des-3200-28:4# config authen server_group used to configure a user-defined authentication server group. Purpose confi...
Page 278
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 273 config authen server_group only administrator-level users can issue this command. Restrictions example usage: to add an authentication host to server group “group_1”: des-3200-28:4# config authen server_group group_1 ad...
Page 279
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 274 show authen server_group none. Restrictions example usage: to view authentication server groups currently set on the switch. Des-3200-28:4#show authen server_group command: show authen server_group group name ip address...
Page 280
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 275 config authen parameter attempt this command is used to configure the maximum number of times the switch will accept authentication attempts. Users failing to be authenticated after the set amount of attempts will be de...
Page 281
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 276 enable admin used to promote user level privileges to administrator level privileges. Purpose enable admin syntax this command is for users who have logged on to the switch on the normal user level to become promoted to...
Page 282
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 277 des-3200-28:4#config admin local_enable command: config admin local_enable enter the old password: enter the case-sensitive new password:****** enter the new password again for confirmation:****** success. Des-3200-28:4...
Page 283: Ssh
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 278 31 ssh c ommands the steps required to use the secure shell (ssh) protocol for secure communication between a remote pc (the ssh client) and the switch (the ssh server), are as follows: create a user account with admin-...
Page 284
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 279 to enable ssh: des-3200-28:4#enable ssh command: enable ssh success. Des-3200-28:4# disable ssh used to disable ssh. Purpose disable ssh syntax this command is used to disable ssh on the switch. Description none. Parame...
Page 285
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 280 des-3200-28:4#config ssh authmode password enable command: config ssh authmode password enable success. Des-3200-28:4# show ssh authmode used to display the ssh authentication mode setting. Purpose show ssh authmode syn...
Page 287
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 282 config ssh user identify the ssh user. Authmode – specifies the authentication mode of the ssh user wishing to log on to the switch. The administrator may choose between: hostbased – this parameter should be chosen if t...
Page 288
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 283 des-3200-28:4#show ssh user authmode command: show ssh user authmode current accounts: username authmode hostname hostip ---------- --------- ------------------------- --------------- zira password total entries : 1 des...
Page 290
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 285 des-3200-28:4#show ssh algorithm command: show ssh algorithm encryption algorithm -------------------------- 3des : enabled aes128 : enabled aes192 : enabled aes256 : enabled arcfour : enabled blowfish : enabled cast128...
Page 291: Ssl
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 286 32 ssl c ommands secure sockets layer or ssl is a security feature that will provide a secure communication path between a host and client through the use of authentication, digital signatures and encryption. These secu...
Page 293
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 288.
Page 295
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 290 config ssl cachetimeout timeout used to configure the ssl cache timeout. Purpose config ssl cachetimeout timeout syntax this command is used to set the time between a new key exchange between a client and a host using t...
Page 296
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 291 show ssl this command is used to view the ssl status on the switch. Description none. Parameters none. Restrictions example usage: to view the ssl status on the switch: des-3200-28:4#show ssl command: show ssl ssl statu...
Page 297
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 292 download ssl certificate use of the ssl function. The switch only supports certificate files with .Der file extensions. Parameters enter the ip address of the tftp server. Certfilename enter the path and the filename of...
Page 298: D-L
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 293 33 d-l ink s ingle ip m anagement c ommands simply put, d-link single ip management is a concept that will stack switches together over ethernet instead of using stacking ports or modules. Switches using d-link single i...
Page 299
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 294 with sim enabled, the applications in the cs will redirect the packet instead of executing the packets. The applications will decode the packet from the administrator, modify some data, and then send it to the ms. After...
Page 300
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 295 enable sim used to enable single ip management (sim) on the switch. Purpose enable sim syntax this command is used to enable sim globally on the switch. Sim features and functions will not function properly unless this ...
Page 302
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 297 example usage: to show the sim information in detail: des-3200-28:4#show sim command: show sim sim version : ver-1.6.07 firmware version : 1.00.B015 device name : mac address : 00-19-5b-ef-78-b5 capabilities : l2 platfo...
Page 303
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 298 to show other groups information in summary: des-3200-28:4#show sim group command: show sim group sim group name : default id mac address platform / hold firmware device name capability time version --- ----------------...
Page 305
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 300 example usage: to add a member: des-3200-28:4#config sim_group add 1 command: config sim_group add 1 please wait for ack !!! Sim config success !!! Success. Des-3200-28:4# to delete a member: des-3200-28:4# config sim_g...
Page 306
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 301 des-3200-28:4# config sim dp_interval 30 command: config sim dp_interval 30 success. Des-3200-28:4# to change the hold time: des-3200-28:4# config sim hold_time 120 command: config sim hold_time 120 success. Des-3200-28...
Page 308
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 303 to download configuration files: des-3200-28:4#download sim_ms configuration_from_tftp 10.53.13.94 c:/des3200.Txt all command: download sim_ms firmware_from_tftp 10.53.13.94 c:/des3200.Txt all this device is updating co...
Page 309
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 304 example usage: to upload configuration files to a tftp server: des-3200-28:4#upload sim_ms configuration_to_tftp 10.55.47.1 d:\configuration.Txt members 1 command: upload sim_ms configuration 10.55.47.1 d:\configuration...
Page 310: Smtp
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 305 34 smtp c ommands smtp or simple mail transfer protocol is a function of the switch that will send switch events to mail recipients based on e-mail addresses entered using the commands below. The switch is to be configu...
Page 311
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 306 the maximum attempts for delivering mail to recipients is three. Mail message delivery attempts will be tried every five minutes until the maximum number of attempts is reached. Once reached and the message has not been...
Page 312
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 307 example usage: to disable smtp on the switch: des-3200-28:4#disable smtp command: disable smtp success. Des-3200-28:4# config smtp used to configure necessary information in setting up the switch as an smtp client. Purp...
Page 313
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 308 show smtp used to view configured parameters for the smtp function on the switch. Purpose show smtp syntax this command is used to display parameters configured for smtp on the switch, including server information, mail...
Page 314
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 309 example usage: to send a test mail message to all configured mail recipients: des-3200-28:4# smtp send_testmsg command: smtp send_testmsg subject: this is a smtp test. Content: hello everybody!! Sending mail, please wai...
Page 316
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 311 des-3200-28:4#cable_diag ports 25-28 command: cable_diag ports 25-28 perform cable diagnostics ... Port type link status test result cable length (m) ---- ------- -------------- -------------------------- --------------...
Page 317: Dhcp
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 312 36 dhcp l ocal r elay c ommands the dhcp local relay commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config dhcp_local _relay vl...
Page 318
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 313 enable dhcp_local_relay only administrator-level users can issue this command. Restrictions example usage: to enable the dhcp local relay function: des-3200-28:4#enable dhcp_local_relay command: enable dhcp_local_relay ...
Page 319: Ratuitous
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 314 37 g ratuitous arp c ommands the gratuitous arp commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config gratuitous_arp send ipif_...
Page 320
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 315 config gratuitous_arp send duplicate_ip_detected used to enable or disable the sending of gratuitous arp requests while duplicate ip addresses are detected purpose config gratuitous_arp send duplicate_ip_detected [enabl...
Page 321
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 316 des-3200-28:4# config gratuitous_arp learning enable command: config gratuitous_arp learning enable success. Des-3200-28:4# config gratuitous_arp_send periodically used to configure the interval for periodical sending o...
Page 322
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 317 des-3200-28:4#enable gratuitous_arp ipif system trap log command: enable gratuitous_arp ipif system trap log success. Des-3200-28:4# disable gratuitous_arp used to disable the gratuitous arp trap and log. Purpose disabl...
Page 323
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 318 des-3200-28:4# show gratuitous_arp command: show gratuitous_arp send on ipif status up : enabled send on duplicate_ip_detected : disabled gratuitous arp learning : enabled ip interface name : system gratuitous arp trap ...
Page 324: Vlan
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 319 38 vlan t runking c ommands the vlan trunking commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters enable vlan_trunk disable vlan_tru...
Page 326
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 321 des-3200-28:4# config vlan_trunk ports 6-7 state enable command: config vlan_trunk ports 6-7 state enable can not operate the member ports of any trunk. Des-3200-28:4# config vlan_trunk ports 7 state disable command: co...
Page 327
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 322 show vlan_trunk used to display vlan trunk configuration. Purpose show vlan_trunk syntax this command is used to display vlan trunk information. Description none. Parameters none. Restrictions example usage: to display ...
Page 328: Ommands
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 323 39 q- in -q c ommands the q-in-q commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters enable qinq disable qinq show qinq show qinq po...
Page 329
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 324 enable qinq this command is used to enable the q-in-q mode. Purpose enable qinq syntax this command is used to enable q-in-q mode. Description when q-in-q is enabled, all network port roles will be nni port and their ou...
Page 330
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 325 show qinq used to show global q-in-q purpose show qinq syntax this command is used to show the global q-in-q status. Description none. Parameters none. Restrictions example usage: to show global q-in-q status: des-3200-...
Page 332
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 327 des-3200-28:4#create vlan_translation add cvid 1-10 svid 100 command: create vlan_translation add cvid 1-10 svid 100 success. Des-3200-28:4# delete vlan_translation cvid used to delete vlan translation rules. Purpose de...
Page 333
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 328 example usage: to show vlan translation rules for c-vid 10 to c-vid 40: des-3200-28:4#show vlan_translation cvid 10-40 command: show vlan_translation cvid 10-40 cvid svid action ---- ---- ------ 10 100 add 20 100 add 30...
Page 334
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 329 show bpdu_tunnel used to show the bpdu tunneling global state, tunnel destination mac address, and port state. Purpose show bpdu_tunnel syntax this command is used to show the bpdu tunneling global state, tunnel destina...
Page 335
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 330 disable bpdu_tunnel the command is used to disable the bpdu tunneling function. Description none. Parameters only administrator-level users can issue this command. Restrictions example usage: to disable bpdu tunneling: ...
Page 336: Symmetric
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 331 40 a symmetric vlan c ommands the asymmetric vlan commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters enable asymmetric_vlan disable...
Page 337
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 332 des-3200-28:4#disable asymmetric_vlan command: disable asymmetric_vlan success. Des-3200-28:4# show asymmetric_vlan used to view the asymmetric vlan state on the switch. Purpose show asymmetric_vlan syntax this command ...
Page 339
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 334 to configure the mld snooping to the default vlan with the state enabled: des-3200-28:4#config mld_snooping vlan default state enable command: config mld_snooping vlan default state enable success. Des-3200-28:4# config...
Page 340
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 335 config mld_snooping querier version - specifies the version of mld packet that will be sent by this port. Only administrator-level users can issue this command. Restrictions example usage: to configure the mld snooping ...
Page 344
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 339 show mld_snooping mrouter_ports the vids of the configured routers to view information for. Static displays router ports that have been statically configured. Dynamic displays router ports that have been dynamically con...
Page 345: Igmp
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 340 42 igmp s nooping m ulticast vlan c ommands the igmp snooping multicast vlan commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters cre...
Page 346
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 341 create igmp_snooping multicast_vlan when remap priority is set. Only administrator-level users can issue this command. Restrictions example usage: to create an igmp snooping multicast vlan with the vlan name “mv1” and a...
Page 347
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 342 config igmp_snooping multicast_vlan with the data traffic to be forwarded on the multicast vlan. If none is specified, the packet’s original priority will be used. The default setting is none. Replace_priority - specifi...
Page 348
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 343 des-3200-28:4#config igmp_snooping multicast_vlan_group v1 add 225.1.1.1 command: config igmp_snooping multicast_vlan_group v1 add 225.1.1.1 success. Des-3200-28:4#.
Page 349
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 344 show igmp_snooping multicast_vlan_group used to display the multicast groups configured for the specified multicast vlan. Purpose show igmp_snooping multicast_vlan_group {} syntax this command is used to display the mul...
Page 350
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 345 enable igmp_snooping multicast_vlan used to enable the multicast vlan function. Purpose enable igmp_snooping multicast_vlan syntax this command is used to control the multicast vlan function. The ism vlan will take effe...
Page 351
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 346 example usage: to display igmp snooping multicast vlan information: des-3200-28:4# show igmp_snooping multicast_vlan command: show igmp_snooping multicast_vlan multicast vlan global state : enabled vid : 4001 vlan name:...
Page 352: Imited
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 347 43 l imited ip m ulticast a ddress c ommands the limited ip multicast address commands allows the administrator to permit or deny access to a port or range of ports by specifying a range of multicast addresses. The limi...
Page 354
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 349 des-3200-28:4# delete mcast_filter_profile profile_id 3 command: delete mcast_filter_profile profile_id 3 success. Des-3200-28:4# delete mcast_filter_profile used to delete a multicast address profile. Purpose delete mc...
Page 355
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 350 des-3200-28:4#show mcast_filter_profile command: show mcast_filter_profile mcast filter profile: profile id name multicast addresses ---------- -------------------------------- ------------------------------- 1 m1 234.1...
Page 356
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 351 des-3200-28:4#config limited_multicast_addr ports 1,3 add profile_id 2 command: config limited_multicast_addr ports 1,3 add profile_id 2 success. Des-3200-28:4# show limited_multicast_addr used to show the per-port limi...
Page 357
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 352 config max_mcast_group config max_mcast_group ports max_group 1024> syntax this command is used to configure the maximum number of multicast groups that a port can join. Description - a range of ports to configure the m...
Page 358
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 353 des-3200-28:4#show max_mcast_group ports 1 command: show max_mcast_group ports 1 max multicast filter group: port maxmcastgroup ---- ------------- 1 1024 des-3200-28:4#.
Page 359: Lldp
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 354 44 lldp c ommands the lldp commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters enable lldp disable lldp config lldp message_tx_inter...
Page 360
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 355 command parameters show lldp statistics show lldp statistics ports {} each command is listed, in detail, in the following sections: enable lldp used to enable lldp operations on the switch. Purpose enable lldp syntax th...
Page 361
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 356 des-3200-28:4# disable lldp command: disable lldp success. Des-3200-28:4#.
Page 362
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 357 config lldp message_tx_interval used to change the packet transmission interval. Purpose config lldp message_tx_interval syntax this command is used to control how often active ports retransmit advertisements to their n...
Page 363
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 358 config lldp tx_delay used to change the minimum time (delay-interval) of any lldp port. It will delay advertising successive lldp advertisements due to a change in lldp mib content. The tx delay defines the minimum inte...
Page 364
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 359 config lldp notification_interval used to configure the timer of the notification interval used to send notifications to configured snmp trap receiver(s). Purpose config lldp notification_interval syntax globally change...
Page 366
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 361 des-3200-28:4# config lldp ports 1-2 mgt_addr ipv4 192.168.254.10 enable command: config lldp ports 1-2 mgt_addr ipv4 192.168.254.10 enable success des-3200-28:4# config lldp ports basic_tvls used to configure an indivi...
Page 367
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 362 des-3200-28:4# config lldp ports all basic_tlvs system_name enable command: config lldp ports all basic_tlvs system_name enable success. Des-3200-28:4# config lldp ports dot1_tlv_pvid used to configure an individual por...
Page 368
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 363 config lldp ports dot1_tlv_protocol_vid dot1_tlv_protocol_vid - this tlv optional data type determines whether the ieee 802.1 organizationally defined port vlan id tlv transmission is allowed on a given lldp transmissio...
Page 370
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 365 config lldp ports dot3_tlvs includes whether the port support the auto-negotiation function, whether the function is enabled, the auto-negotiated advertised capability, and the operational mau type. The default state is...
Page 371
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 366 des-3200-28:4# config lldp forward_ message enable command: config lldp forward_ message enable success. Des-3200-28:4# show lldp this command displays the switch’s general lldp configuration status. Purpose show lldp s...
Page 372
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 367 to display the management address information: des-3200-28:4# show lldp mgt_addr ipv4 192.168.254.10 command: show lldp mgt_addr ipv4 192.168.254.10 total address:1 des-3200-28:4# show lldp ports used to display the lld...
Page 373
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 368 des-3200-28:4# show lldp ports 1 command: show lldp ports 1 port id : 1 --------------------------------------------------------------------- admin status : tx_and_rx notification status : disable advertised tlvs option...
Page 374
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 369 des-3200-28:4# show lldp local_ports 1 mode detailed command: show lldp local_ports 1 mode detailed port id : 1 -------------------------------------------------------------------- port id subtype : local port id : 1/1 ...
Page 375
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 370 des-3200-28:4# show lldp local_ports 1 mode brief command: show lldp local_ports 1 mode brief port id : 1 --------------------------------------------------------- port id subtype : local port id : 1/1 port description ...
Page 376
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 371 des-3200-28:4# show lldp remote_ports 1-2 brief command: show lldp remote_ports 1-2 brief port id: 1 ----------------------------------------------------------- remote entities count : 3 entity 1 chassis id subtype : ma...
Page 377
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 372 to display remote table entries in normal mode: des-3200-28:4# show lldp remote_ports ports 1 normal command: show lldp remote_ports ports 1 normal port id : 1 -----------------------------------------------------------...
Page 378
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 373 to display remote table entries in detailed mode:.
Page 379
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 374 des-3200-28:4# show lldp remote_ports 1 mode detailed command: show lldp remote_ports 1 mode detailed port id : 1 ---------------------------------------------------------------------- remote entities count : 1 entity 1...
Page 380
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 375 maximum frame size : 1536 unknown tlvs count : 0 (none.) des-3200-28:4# show lldp statistics used to display the system lldp statistics information. Purpose show lldp statistics syntax this command is used to display an...
Page 381
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 376 des-3200-28:4# show lldp statistics ports 1 command: show lldp statistics ports 1 port id: 1 ----------------------------------------------------------- lldpstatstxportframestotal : 27 lldpstatsrxportframesdiscardedtota...
Page 382: Revention
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 377 45 d o s p revention c ommands the dos prevention commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters config dos_prevention dos_type...
Page 384
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 379 enable dos_prevention trap_log used to enable a dos prevention trap/log. Purpose enable dos_prevention trap_log syntax this command is used to send traps and logs when a dos attack event occurs. The event will be logged...
Page 386
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 381 to display dos prevention information for land attack: des-3200-28:4# show dos_prevention land_attack command: show dos_prevention land_attack dos type: land attack state: enabled action: mirror port: 7 priority: 5 rx r...
Page 387
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 382 example usage to clear all counters of the prevention of each dos attack: des-3200-28:4# clear dos_prevention counters command: clear dos_prevention counters success. Des-3200-28:4#.
Page 388: Ip-Mac-P
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 383 46 ip-mac-p ort b inding c ommands the ip network layer uses a four-byte address. The ethernet link layer uses a six-byte mac address. Binding these two address types together allows the transmission of data between the...
Page 390
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 385 example usage: to configure address binding on the switch: des-3200-28:4#config address_binding ip_mac ipaddress 10.1.1.3 mac_address 00- 00-00-00-00-05 command: config address_binding ip_mac ipaddress 10.1.1.3 mac_addr...
Page 391
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 386 example usage: to configure address binding on the switch: des-3200-28:4#config address_binding ip_mac ports 2 state enable command: config address_binding ip_mac ports 2 state enable success. Des-3200-28:4# show addres...
Page 392
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 387 des-3200-28:4#show address_binding ip_mac all command: show address_binding ip_mac all ip address mac address mode acl status ports --------------- ----------------- --------------- --------- ---------- 10.1.1.1 00-00-0...
Page 394
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 389 enable address_binding trap_log used to enable the trap log for the ip-mac-port binding function. Purpose enable address_binding trap_log syntax this command, along with the disable address_binding trap_log will enable ...
Page 396
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 391 to display address binding dhcp snooping maximum entry: des-3200-28:4#show address_binding dhcp_snoop max_entry command: show address_binding dhcp_snoop max_entry port max entry ---- --------- 1 5 2 5 3 5 4 5 5 5 6 5 7 ...
Page 397
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 392 example usage to enable address binding dhcp snooping: des-3200-28:4#enable address_binding dhcp_snoop command: enable address_binding dhcp_snoop success. Des-3200-28:4# disable address_binding dhcp_snoop used to disabl...
Page 399
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 394 enable address_binding arp_inspection used to enable arp inspection. Purpose enable address_binding arp_inspection syntax this command is used to filter arp packets which have unauthorized sender mac, ip address, and in...
Page 400: Oopback
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 395 47 l oopback d etection c ommands the loopback detection commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters config loopdetect { rec...
Page 403
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 398 enable loopdetect used to globally enable the loop-detect function on the switch. Purpose enable loopdetect syntax this command is used to allow the loop detection function to be globally enabled on the switch. The defa...
Page 404
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 399 show loopdetect used to display the switch’s current loopback detection configuration. Purpose show loopdetect syntax this command is used to display the switch’s current loopback detection configuration. Description no...
Page 407: Rotocol
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 402 48 p rotocol vlan c ommands the protocol vlan commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters create dot1v_protocol_group group_...
Page 408
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 403 create dot1v_protocol_group used to create a protocol group for the protocol vlan function. Purpose create dot1v_protocol_group group_id {group_name } syntax this command is used to create a protocol group for the proto...
Page 409
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 404 example usage: to add a protocol ipv6 to protocol group 1: des-3200-28:4#config dot1v_protocol_group group_id 1 add protocol ethernet_2 0x86dd command: config dot1v_protocol_group group_id 1 add protocol ethernet_2 0x86...
Page 412
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 407 show port dot1v used to display the vlan to be associated with untagged packets ingressed from a port based on the protocol group. Purpose show port dot1v {ports } syntax this command is used to display the vlan to be a...
Page 413: Mac-
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 408 49 mac- based vlan c ommands the mac-based vlan commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters create mac_based_vlan mac_addres...
Page 414
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 409 create mac_based_vlan used to create a static mac-based vlan entry. Purpose create mac_based_vlan mac_address vlan syntax this command is used to create a static mac-based vlan entry. Description when a static mac-based...
Page 416: Low
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 411 50 f low m eter c ommands the flow meter commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters config flow_meter profile_id access_id ...
Page 418
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 413 show flow_meter used to display the flow-based metering configuration. Purpose show flow_meter {profile_id {access_id }} syntax this command displays the flow meter configuration. Description profile_id – specifies the ...
Page 419: Mac-
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 414 51 mac- based a ccess c ontrol c ommands the mac-based access control commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters enable mac...
Page 421
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 416 enable mac_based_access_control used to enable mac-based access control. Purpose syntax enable mac_based_access_control this command enables mac-based access control on the switch. By default this is not enabled. Descri...
Page 422
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 417 config mac_based_access_control password used to configure the password of the mac-based access control. Purpose config mac_based_access_control password syntax this command will set the password that will be used for a...
Page 426
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 421 clear mac_based_access_control auth_mac used to reset the current state of a user. The re-authentication will be started after the user traffic is received again. Purpose clear mac_based_access_control auth_mac [ports [...
Page 428
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 423 des-3200-28:4#delete mac_based_access_control_local vlan default command: delete mac_based_access_control_local vlan default success. Des-3200-28:4# show mac_based_access_control used to display the mac-based access con...
Page 430
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 425 to display mac-based access control local databases by vlan: des-3200-28:4#show mac_based_access_control_local vlan default command: show mac_based_access_control_local vlan default mac address vlan name vid -----------...
Page 432
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 427 config mac_based_access_control authorization attributes used to enable or disable local or radius authorization to accept an authorized configuration. Purpose config mac_based_access_control authorization attributes { ...
Page 433
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 428 enable authorization attributes the enable authorization command globally enables the authorization for attributes function. Purpose enable authorization attributes syntax used to enable authorization attributes. When e...
Page 434
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 429 show authorization used to display authorization for attributes status. Purpose show authorization syntax used this to view authorization for attributes status. Description none. Parameters none. Restrictions example us...
Page 436: Arp
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 431 52 arp s poofing p revention c ommands the arp spoofing prevention commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters config arp_sp...
Page 438
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 433 show arp_spoofing_prevention used to display arp spoofing prevention entries. Purpose show arp_spoofing_prevention syntax this command is used to display arp spoofing prevention entries. Description none. Parameters non...
Page 439: Echnical
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 434 53 t echnical s upport c ommands the technical support commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters show tech_support upload ...
Page 440
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 435 des-3200-28:4#show tech_support command: show tech_support des-3200-28 fast ethernet switch technical information report ============================================================================= [cpu utilization 829...
Page 441
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 436.
Page 442
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 437 upload tech_support_totftp used to upload information for assistance from technical support. Purpose upload tech_support_totftp syntax this command is used to upload information for assistance from technical support to ...
Page 443: Ommand
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 438 54 c ommand h istory c ommands the command history commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters ? Dir config command_history ...
Page 444
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 439 des-3200-28:4#? .. ? Cable_diag ports clear clear address_binding dhcp_snoop binding_entry ports clear arptable clear counters clear dos_prevention counters clear fdb clear igmp_snooping data_driven_group clear log clea...
Page 445
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 440 dir used to display all commands in the command line interface (cli). Purpose dir syntax this command is used to display all of the commands available through the command line interface (cli). Description none. Paramete...
Page 446
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 441 config command_history used to configure the command history. Purpose config command_history syntax this command is used to configure the command history. Description parameters the number of previously executed command...
Page 447: Onnectivity
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 442 55 c onnectivity f ault m anagement c ommands connectivity fault management (cfm) or ethernet connectivity fault management is an end-to-end ethernet layer oam protocol. Cfm is defined by ieee 802.1ag and includes conne...
Page 448
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 443 forwards all cfm frames at a higher level regardless of the origin of the frame, inward or outward. If the port on which the inward mep is configured is blocked by spanning-tree protocol, the mep can no longer transmit ...
Page 449
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 444 the connectivity fault management (cfm) commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create cfm md level config cfm md { mip ...
Page 450
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 445 create cfm md used to create a maintenance domain for cfm. Purpose create cfm md level syntax use this command to create a cfm maintenance domain and set the level for that domain. Description md - the new cfm maintenan...
Page 451
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 446 example usage to configure the maintenance domain called “op_domain” and specify the explicit option for creating mips: des-3200-28f:4# config cfm md op_domain mip explicit command: config cfm md op_domain mip explicit ...
Page 453
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 448 example usage to configure parameters for ma “op1”: des-3200-28f:4# config cfm ma op1 md op_domain vlan 1 ccm_interval 1sec command: config cfm ma op1 md op_domain vlan 1 ccm_interval 1sec success. Des-3200-28f:4# creat...
Page 454
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 449 des-3200-28f:4# create cfm mep mep1 mepid 1 md op_domain ma op1 direction inward port 2 command: create cfm mep mep1 mepid 1 md op_domain ma op1 direction inward port 2 success. Des-3200-28f:4#.
Page 456
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 451 example usage: to configure parameters for mep “mep1”: des-3200-28f:4# config cfm mep mep1 state enable ccm enable command: config cfm mep mep1 state enable ccm enable success. Des-3200-28f:4# delete cfm mep this comman...
Page 457
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 452 delete cfm ma this command is used to delete a previously created maintenance association. Purpose delete cfm ma md syntax all meps created in the maintenance association will be deleted automatically. Description ma - ...
Page 458
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 453 enable cfm this command is used to enable the cfm globally. Purpose enable cfm syntax this command is used to enable the cfm globally. Description none. Parameters only administrator-level users can issue this command. ...
Page 460
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 455 example usage to view cfm settings for ports 3-6: des-3200-28f:4# show cfm ports 3-6 command: show cfm ports 3-6 port state ----- --------- 3 enabled 4 enabled 5 enabled 6 disabled des-3200-28f:4# show cfm this command ...
Page 461
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 456 to view cfm settings for md “op_domain” ma “op1”: des-3200-28f:4# show cfm md op_domain ma op1 command: show cfm md op_domain ma op1 ma vid : 1 mip creation : none ccm interval : 10 second(s) senderid tlv : defer mepid ...
Page 462
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 457 to view cfm settings for mep “mep1”: des-3200-28f:4# show cfm mepname mep1 command: show cfm mepname mep1 name : mep1 mepid : 1 port : 1 direction : inward cfm port state : enabled mac address : 00-04-a8-00-00-03 mep st...
Page 463
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 458 show cfm fault this command is used to show the meps that have faults. Purpose show cfm fault { md { ma } } syntax this command displays all the fault conditions detected by the meps contained in the specified ma or md....
Page 464
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 459 example usage: to display cfm configuration for port 1: des-3200-28f:4# show cfm port1 command: show cfm port1 mac address: 00-05-78-82-32-01 md name ma name mepid level direction vid ----------- ----------- ----- -----...
Page 465
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 460 example usage to initiate a loopback test from mep “mep1”: des-3200-28f:4# cfm loopback 00-01-02-03-04-05 mep mep1 command: cfm loopback 00-01-02-03-04-05 mep mep1 request timed out. Request timed out. Reply from mpid 5...
Page 467
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 462 to view link trace results for trace of mep “mep1” transaction “tras_id 26”: des-3200-28f:4# show cfm linktrace mep mep1 trans_id 26 command: show cfm linktrace mep mep1 trans_id 26 transaction id: 26 from mep mep1 to 0...
Page 469
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 464 show cfm mipccm this command is used to display the mip ccm database entries. Purpose show cfm mipccm syntax all entries in the mip ccm database will be shown. A mip ccm entry is similar to a fdb which keeps the forward...
Page 470
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 465 example usage: to enable all mps to reply to ltm: des-3200-28f:4# config cfm mp_ltr_all enable command: config cfm mp_ltr_all enable success. Des-3200-28f:4# show cfm mp_ltr_all this command is used to show the current ...
Page 471
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 466 to view remote mep information for remote mep id “2”: des-3200-28f:4# show cfm remote_mep mepname mep1 remote_mepid 2 command: show cfm remote_mep mepname mep1 remote_mepid 2 remote mepid : 2 mac address : 00-11-22-33-4...
Page 472
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 467 8 0 0 0 0 0 0 9 0 0 0 0 0 0 10 0 0 0 0 0 0 11 0 0 0 0 0 0 12 0 0 0 0 0 0 --------------------------- port viddrop opcodrop ----- ---------- ---------- all 0 0 1 0 0 2 0 0 3 0 0 4 0 0 5 0 0 6 0 0 7 0 0 8 0 0 9 0 0 10 0 0...
Page 473
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 468 example usage: to display the cfm packet ccm counters: des-3200-28:4# show cfm pkt_cnt ccm command: show cfm pkt_cnt ccm ccm rx counters: xcon = cross-connect ccms error = error ccms normal = normal ccms mep name vid po...
Page 474: Thernet
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 469 56 e thernet oam c ommands ethernet oam (operations, administration, and maintenance) is a data link layer protocol which provides network administrators the ability to monitor the health of the network and quickly dete...
Page 477
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 472 des-3200-28f:4# config ethernet_oam ports 1 link_monitor error_symbol threshold 2 window 1000 notify_state enable commands: config ethernet_oam ports 1 link_monitor error_symbol threshold 2 window 1000 notify_state enab...
Page 483
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 478 show ethernet_oam ports (status) activesendlocal : the port is active and is sending local information sendlocalandremote : the local port has discovered the peer but has not yet accepted or rejected the configuration o...
Page 484
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 479 example usage to show oam control and status information on port 1-2: des-3200-28f:4# show ethernet_oam ports 1-2 status commands: show ethernet_oam ports 1-2 status port 1 ------------------- local client oam : disable...
Page 485
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 480 show ethernet_oam ports (configuration) used to display ethernet oam configuration per port. Purpose show ethernet_oam ports {} configuration syntax use this to view ethernet oam configurations for ports. Description - ...
Page 486
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 481 example usage: to show ethernet oam configuration on port 1-2: des-3200-28f:4# show ethernet_oam ports 1-2 configuration commands: show ethernet_oam ports 1-2 configuration port 1 ---------------------------------------...
Page 487
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 482 show ethernet_oam ports (statistics) used to display ethernet oam statistics for ports. Purpose show ethernet_oam ports {} statistics syntax use this command to display ethernet oam ports statistics information. Descrip...
Page 488
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 483 show ethernet_oam ports (event log) used to display ethernet oam event log purpose show ethernet_oam { } event_log { index } syntax use this command to view ports ethernet oam event log information. The switch can buffe...
Page 490: Bpdu
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 485 57 bpdu a ttack p rotection c ommands the bpdu attack protection commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config bpdu_pro...
Page 492
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 487 example usage: to set the bpdu attack protection port state to enable and drop mode: des-3200-28f:4# config bpdu_protection ports 1 state enable mode drop commands: config bpdu_protection ports 1 state enable mode drop ...
Page 494
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 489 enable bpdu_protection used to globally enable bpdu attack protection on the switch. Purpose enable bpdu_protection syntax use this to enable bpdu attack protection. Description note: the bpdu attack protection function...
Page 495
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 490 disable bpdu_protection used to disable bpdu attack protection on the switch. Purpose disable bpdu_protection syntax use this to disable bpdu attack protection on the entire switch. Note that if bpdu attack protection i...
Page 496
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 491 example usage: to display bpdu protection settings for ports: des-3200-28f:4# show bpdu_protection ports 1-12 commands: show bpdu_protection ports 1-12 port state mode status ------ ------------ ----------- ---------- 1...
Page 497: Ueue
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 492 58 p er -q ueue b andwidth c ontrol c ommands the per-queue bandwidth control commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table: command parameters co...
Page 499
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 494 show per_queue bandwidth_control used to display the configuration settings for per-queue bandwidth control. Purpose show per_queue bandwidth_control {} syntax use this command to view the per-queue bandwidth limits set...
Page 500: Erps
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 495 59 erps c ommands the ethernet ring protection switching (erps) defined in itu-t g.8032 is intended to provide a protection switching and recovery process, and to prevent loops forming for ethernet in a ring topology. T...
Page 501
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 496 enable erps used to enable the global erps function on the switch. Purpose enable erps syntax this command is used to enable the global erps function on the switch. For each ring with the ring state enabled when erps is...
Page 502
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 497 create erps vlan used to define an existing vlan as an r-aps vlan on the switch. Purpose create erps raps_vlan syntax use this command to create a special r-aps vlan that is used for transferring r-aps control messages....
Page 503
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 498 config erps ring_mel used to configure the mel (maintenance entity group level) value. Purpose config erps raps_vlan ring_mel syntax this command is used to configure the ring mel for an r-aps vlan. The ring mel is one ...
Page 509
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 504 example usage: to display current erps information: des-3200-28f:4# show erps command: show erps erps information --------------------------- erps status : enabled r-aps vlan : 8 west port : 25 (blocking) east port : 26...
Page 510: Etwork
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 505 60 n etwork l oad b alancing (nlb) c ommands the network load balancing (nlb) commands are used to configure the switch to support network load balancing service, a proprietary microsoft implementation of server cluster...
Page 511
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 506 create nlb unicast_fdb used to create an entry for the nlb unicast fdb. Purpose create nlb unicast_fdb syntax for nlb, the switch uses a fdb that is separate from and independent of the layer 2 unicast fdb. Since a mac ...
Page 512
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 507 delete nlb unicast_fdb used to remove a previously created mac address entry from the nlb unicast fdb. Purpose delete nlb unicast_fdb syntax the delete nlb unicast_fdb command is used to remove an entry from the nlb fdb...
Page 515
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 510 example usage: to configure a nlb multicast mac forwarding database entry: des-3200-28f:4# config nlb multicast_fdb default 03-bf-01-01-01-01 add 1-5 command: config nlb multicast_fdb default 03-bf-01-01-01-01 add 1-5 s...
Page 516: Ppp
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 511 61 ppp o e c ircuit id i nsertion c ommands pppoe circuit id insertion is used to produce the unique subscriber mapping capability that is possible on atm networks between atm-dsl local loop and the pppoe server. The pp...
Page 518
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 513 config pppoe circuit_id_insertion ports used to enable and disable pppoe circuit identifier insertion on a per port basis and specify how to encode the circuit id option. Purpose config pppoe circuit_id_insertion ports ...
Page 519
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 514 to view the global pppoe id insertion state: des-3200-28f:4# show pppoe circuit_id_insertion command: show pppoe circuit_id_insertion status: disabled des-3200-28f:4# show pppoe circuit_id_insertion ports used to displa...
Page 520: Dhcp
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 515 62 dhcp s erver s creening s ettings due to this function allow you not only to restrict all dhcp server packets but also to receive any specified dhcp server packet by any specified dhcp client, it is useful when one o...
Page 521
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 516 config filter dhcp_server dhcp server packets except those that have been ip/client mac bound will be filtered. This command is used to configure the state of the function for filtering of dhcp server packet and to add/...
Page 522
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 517 show filter dhcp_server used to display current dhcp server/client filter list created on the switch. Purpose show filter dhcp_server syntax this command is used to display dhcp server/client filter list created on the ...
Page 524: Ppendix
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 519 a ppendix a -t echnical s pecifications general protocols ieee 802.3 10base-t ethernet ieee 802.3u 100base-tx fast ethernet ieee 802.3ab 1000base-t gigabit ethernet ieee 802.3z 1000base-t (sfp “mini gbic”) ieee 802.1d s...
Page 525
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 520 physical and environmental power consumption des-3200-10: 12.7w des-3200-18: 13.2w des-3200-26: 13.8w des-3200-28: 18.4w des-3200-28f: 46.7w internal power supply des-3200-10/des-3200-18: 34w ac input: 100~240 vac, 12v/...
Page 526: Led Indicators
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 521 led indicators location led indicative color status description solid light power on. Power green light off power off. Solid light console on. Per device blinking post is in progress/post is failure. Console green light...
Page 527: Ppendix
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 522 a ppendix b - p assword r ecovery p rocedure this document describes the procedure for resetting passwords on d-link switches. Authenticating any user who tries to access networks is necessary and important. The basic a...
Page 528
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 523 in the “password recovery mode” only the following commands can be used. Command parameters reset config the reset config command resets the whole configuration will be back to the default value reboot the reboot comman...
Page 529: Ppendix
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 524 a ppendix c - radius a ttributes a ssignment the radius attributes assignment on the des-3200 is used in the following modules: 802.1x (port-based and host-based), and mac-based access control. The description that foll...
Page 530
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 525 to assign 802.1p default priority by radius server , the proper parameters should be configured on the radius server. The tables below show the parameters for 802.1p default priority. The parameters of the vendor-specif...
Page 531
Xstack® des-3200 series layer 2 ethernet managed switch cli reference manual 526 if the user has configured the vlan attribute of the radius server (for example, vid 3) and the 802.1x, or mac-based access control authentication is successful, the port will be added to vlan 3. However, if the user do...