Dacor EPICURE EG366 Installation Instructions Manual - page 14
12
InstallatIon InstructIons
vErIfyIng propEr opEratIon
WarnInG
Do not use an extension cord with this appliance. Such use may
result in fire, electric shock or other personal injury.
Prior to operating the cooktop, please read the
accompanying use and care manual carefully. Important
safety, service and warranty information is contained within
the use and care manual.
Before beginning the test procedure
1.
, make sure that:
- The power plug is disconnected from the wall receptacle.
- All cooktop control valves are in the oFF position,
- All burner rings, burner caps and grates are properly
positioned on the cooktop frame.
Turn on the gas supply valve and check all gas supply lines
2.
and connections for leaks using a soap and water solution.
Do not use a flame to check for leaks.
After verifying that there are no gas leaks, connect the power
3.
cord to the electrical outlet.
T
4.
est each cooktop burner separately by pushing in and
turning one control knob at a time counterclockwise to the
hIGh position. It may take up to four (4) seconds for ignition
to occur, at which time the ignitor will stop sparking. If ignition
does not occur within four seconds, turn the knob to oFF,
wait for at least two minutes to allow any gas to dissipate,
then repeat the ignition test. After ignition, rotate the control
knob counterclockwise from hIGh to LoW to adjust the
flame height progressively. When the cooktop and burners
are installed properly, the flame will be steady and quiet. It
will also have a sharp, blue inner cone that will vary in length
proportional to the burner size. If the cooktop is equipped for
use with LP gas, the ends of the flame may be yellow at the
tips, which is normal.
Turn the control knob to the
5.
oFF position.
Repeat the ignition test for all
6.
remaining burners.
noTe: If the cooktop does not operate properly, follow
these troubleshooting steps:
Verify that power and gas are supplied to the cooktop.
1.
Check the electrical connections and gas supply to ensure
2.
that the installation has been completed correctly.
Repeat the above burner ignition test.
3.
If the appliance still does not work, contact
4.
the Dacor
Customer Service Team at (800) 793-0093.
Do not attempt to repair the appliance yourself. Dacor
is not responsible for service required to correct a faulty
installation.
InstallatIon chEcklIst
WarnInG
To ensure a safe and proper installation, the following
•
checklist should be completed by the installer to ensure that
no part of the installation has been overlooked.
Proper installation is the responsibility of the homeowner.
•
The importance of proper installation of your Dacor cooktop
cannot be overemphasized.
Is the
□
electrical outlet for the cooktop grounded
and located according to these instructions and in
accordance with all applicable electrical codes? (See
Pages 4, 5 and 9).
Is the
□
gas service for the cooktop located and installed
according to these instructions and in accordance with
all applicable codes? (See Pages 4, 5 and 9).
Has the gas supply inlet pressure been measured to
□
ensure that it does not exceed the maximums stated in
these instructions? (See pages 4).
Is the cooktop secured using the provided hold-down
□
bolts? (See page 7).
Is the cooktop connected to the gas supply according
□
to these instructions and in accordance with all
applicable codes? (See page 9).
Are the burners and grates properly installed according
□
to these instructions? (See page 10).
Are the burner knobs installed on the right valves?
□
(See page 11).
Has proper operation been verified?
□
Did the installer
check the gas supply for leaks?
Have any problems been noted on the warranty card
□
or during the on-line warranty activation? Has the
warranty been activated on-line or the warranty card
filled out completely and mailed?