Dacor Epicure ER36D Installation Instructions Manual - Nstallation
I
nsTallaTIon
I
nsTruCTIons
g
as
s
upply
C
onneCTIon
WarnInG
WarnInG:
Do not apply excessive pressure when tightening gas
connections and fittings.
Do not use Teflon tape or plumber’s putty on gas flex line
connections.
Turn all cooktop control valves to the “OFF” position. Turn
on the gas supply and check all lines and connections for
leaks using a soap and water solution. Do not use a flame
to check for leaks. After verifying that there are no gas
leaks, turn off the gas supply to the range by turning the
gas shut-off valve to the “OFF” position.
For LP installations, the LP gas tank must have its own
high pressure regulator. This is in addition to the pressure
regulator provided with the range.
The maximum gas supply pressure to the regulator must
never exceed 1/2 pound per square inch (psi) or 3.5kPa.
The range and shut-off valve must be disconnected
from the gas supply piping during any pressure testing
exceeding 1/2 psi (3.5kPa).
The range must be isolated from the gas supply piping by
closing the shut-off valve during any pressure testing at or
below 1/2 psi (3.5 kPa).
•
•
•
•
•
•
noTe: The gas pressure regulator is pre-set at the factory for the
type of gas intended for use with the appliance. To verify that the
appliance is compatible with the type of gas available, check the
range data plate (see page 3 for location). Ranges intended for
use with LP gases will have “LP” as a part of the model number.
Consult your dealer if the range is not compatible with the type of
gas supplied.
Before sliding the range into the cabinet:
Make sure the gas supply valve is in the off position.
Connect a flexible gas supply line to the gas shut-off valve
previously installed on the stub out. The gas line needs to be
long enough to allow the range to be pulled out for service.
Remove the gas regulator access cover.
1.
2.
3.
Connect the gas line to the regulator.
Turn on the gas supply and check for leaks.
Turn the gas supply off.
Replace the regulator access cover.
f
Inal
I
nsTallaTIon
Peel the protective coating off the sides of the range, if
applicable.
Carefully slide the range into position in the cut-out. The rear
anti-tip leg should engage the anti-tip bracket.
re-installing the oven Door(s)
WarnInG
WarnInG: To avoid personal injury or damage to the door due
to it falling off its hinges:
Make sure that the notch on the bottom of each hinge rests
on top of the lower lip of each hinge receptacle before
attempting to open the oven door.
Rotate the hinge locks toward the front of the range
immediately after installation of the door.
•
•
Grasp the oven door on opposite sides and hold it at a 15°
angle from the front of the oven. Slide the hinges into the
hinge openings, resting the bottom of the hinge arms on the
hinge receptacles. Continue to hold the door at a 15° angle
with one hand while pushing in on each of the bottom corners
of the door. Push until the notch on the bottom of each hinge
slips over the lower lip of each hinge receptacle.
Lower the door to the fully opened position.
Rotate the two hinge locks toward the oven.
Slowly and carefully open and close the door completely to
ensure that it is properly installed.
Remove the protective plastic from the front of the range and
any packaging from inside the oven(s).
4.
5.
6.
7.
1.
2.
1.
2.
3.
4.
5.
Gas and electrical access covers
Gas regulator
access cover
Back of range
electrical access cover
notch on bottom
of hinge
Lower lip of
hinge receptacle
Door Installation