I nstall ation i nstructions m i llenn ia ™ 24-i nch b u i lt -i n d ishwasher for use with model: mdw24s part no. 101586 rev. B.
1 appliance safety ..................................................................... 1 design specifications ............................................................. 2 product dimensions............................................................... 2 installation specifications ..............
2 p roduct d imensions d esign s pecifications make sure the area selected for the installation site meets product dimension requirements. I nstallation s pecifications m aterials not included but n eeded for a ll i nstallations • 90° elbow (3/8” npt external thread on one end, opposite end sized to...
3 i nstallation s pecifications i nstallation t ips please read all safety instructions before installing your new dishwasher. Warning warning – electric shock hazard: disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Failure to follow this warning cou...
4 i nstallation s pecifications 1 review dimensions in figure 3 to locate the dishwasher’s drain, water and electrical connections. 2 all connections must be made in the shaded area of figure 2 , page 3 m aking the e lectrical c onnection 1 the dishwasher operates on a 120 volt, 60 hz electrical sup...
5 i nstall s pecifications m aking the d rain c onnection caution caution– to prevent siphoning, an air gap must be used when waste tee or disposer connection is less than 18” above the floor to prevent siphoning. Failure to provide the proper drain connection using an air gap or a 30” minimum high ...
6 i nstallation i nstructions r emoving the p ackaging 1 cut the shipping carton and use it as a pad beneath the dishwasher. This will protect the finished floor in the kitchen. 2 remove wrapping and uncoil the drain hose in the back of the dishwasher. Do not remove the rear insulation blanket. 3 la...
7 i nstallation i nstructions i nstalling the e lbow 1 locate the water inlet valve. The valve has a 3/8” npt female fitting. See figure 12. 2 wrap 90° elbow with thread seal tape (or apply joint compound) and thread it into the water inlet valve. Wrap tape in the same direction as the elbow threads...
8 i nstallation i nstructions f inishing the d rain c onnection note: follow all local codes and ordinances. When connecting the drain line to the disposer, check to be sure that the knockout plug has been removed. Dishwasher will not drain if the plug is left in place. The dishwasher is supplied wi...
9 i nstallation i nstructions s ecuring to c abinet and c ountertop to maintain position and alignment, it is recommended to secure the dishwasher to the countertop and adjacent cabinets. 0dnhvxuhvxiÀflhqwfrxqwhuwrsvxssruw exists: 1 if mounting the dishwasher to the countertop, check at a depth of 2...
10 i nstallation i nstructions 1 loosen depth adjustment screws. 2 slide bracket out to proper depth and tighten screws. See figure 21. 3 attach supplied toekick to brackets with provided color matched screws. 4 tighten screws. I nstalling the t oekick a djusting s tainless s teel t rim p lates your...
11 s ervice i nformation if you need service, be sure to have the model and serial numbers when you call. You’ll find these numbers on the serial number plate located on the light shield in the fresh food compartment. Contact a dacor ® authorized servicer, a dacor ® dealer, or the dacor ® customer s...
12 n otes.
The information and images in this book are the copyright property of distinctive appliances, inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of distinctive appliances, inc. ©2006 distinctive appli...
