Eagle 680022 Operator's Manual - Adjusting Handle
Eagle Solutions, ©2008, Tracker Operator Manual Page #10
Eagle Solutions, ©2008, Tracker Operator Manual Page #11
Checking Oil Levels and Filters
Checkoillevelspriortostartingengine.Refer
toengineowner’smanualfortheproperprocedure.
DONOTOVERFILLOILLEVEL;todosomay
cause damage to the engine and may elevate
harmfulemissions.Use10W30oil.Alwayscheck
oil daily before using the machine (see “Daily
Maintenance”).
Be sure the carburetor air filter is free of dust,
oil,etc.Dirtyfiltersarethemostfrequentcauseof
elevatedtoxicemissions.
Check recoil dust filter. Clean or replace if
necessary. See the instructions in the engine
owner’smanual.
Adjusting Handle
Your machine is equipped with an adjustable
handleforcomfortanduse.Mostfinditnecessary
to adjust the handle to “belt height” for optimum
control.A9/16wrenchisusedtoloosenandtighten
thepivotpoints.
The handle folds over the engine to facilitate a
compact transport space. However, leaving the
handle loose when operating, allows the operator
tofoldthehandlewhileusingtheTrackerintight
spaces.
Installing the Fuel Cylinder
1. Takemachinetowellventilatedarea.
2. Checkcylinderforoverfill.
3. Placecylinderonthemachineintankholding
areaandsecurethestrap.
4. Connectfuelcylindertothemachineusingthe
“Rego”connection.Tightenhandtight.Donot
useawrenchorpliersorcrossthreadtheRego
connection.
5. Opentheservicevalveslowly.Bealertforthe
odorofpropanethatmayindicatealeak.
6. Toremovethecylinder,reversetheprocedure.
Strip Brush Or Pad Driver
Installation & Inspection
1. Place transport wheel on Tracker & install
safetychain.
2. Lying on floor, grip strip brush or pad driver
withbothhands.Firmlytwistinalefttoright
rapidmotion.
3. Removeandinspect.
4. Reinstallinsimilarmotion.
5. Removetransportwheel.
Transport Wheel Installation,
Removal
1. Position one operator at Tracker handle,
pressingdowntoliftfrontendofmachine.
2. Second operator removes or installs transport
wheel.
3. When installing transport wheel, position
so that the chain on the transport wheel that
holdsthesecurepinisinthefront,awayfrom
the Tracker. This assures that the wheel is
positionedproperly,allowingeaseofmovement
whenpushingtheTrackertostorage.
Starting Machine
1. Check fuel cylinder for overfill and install
cylinderonmachine.
2. Installbothstripbrushesorpaddedpaddrivers
ontomachine.
3. Remove transport wheel. Store in a secure
location.
4. Placemachineonlevelsurfaceandcheckfor
correctoillevel.
5. Lowersplashguardskirttofloorlevel.
6. Slowly open the service valve on the fuel
cylinder.NOTE: Opening the service valve too
quickly may cause the excess flow valve to stop
the flow of propane. If this occurs, close the
valve, wait a few seconds and re-open the valve
SLOWLY!
7. Chokeengineandengagestarterwiththrottlein
‘slow’position.
5. When engine starts, ease the throttle back to
running position. NOTE: Do not run engine
with the throttle in the choke position! Excessive
harmful emissions will be produced putting you
in harm’s way!
7. Increasethrottle.Centrifugalclutchwillengage
and brushes will begin turning. Continue
increasingthrottleto100%positionasmachine
movesforward.
Operating Machine
WARNING! Be careful not to allow the machine to
come in contact with loose tiles or other obstructions
on the floor. If objects are hit by the revolving pad
they could become dangerous projectiles.
1. Clearareaofalldisplays.Removeanydustand
stickersfromfloor.
2. Prepare stripping solutions according to
instructionsonthechemicallabel.
3. Apply solution to the floor using a mop or
solutionspreader.KEEPFLOORWETWITH
SOLUTION!
Machine Set-Up & Operation
To Order Parts Call 1-888-702-5326 - https://monsterfloorequipmentparts.com