Eagle 680022 Operator's Manual - Hours of Operation)
Eagle Solutions, ©2008, Tracker Operator Manual Page #12
Eagle Solutions, ©2008, Tracker Operator Manual Page #13
Daily Maintenance - (every four
hours of operation)
• Check oil level (use 10W30 or SAE30 oil
only).
• Checkandcleanrecoildustfilter.
• Checkandcleancarburetorairfilter.
• Check belt tension by pinching belt together.
Beltshoulddeflectonly½”(13mm).
• Make sure all components (pad holder, fuel
cylinder,etc.)aresecureandtight.
• Check pad holder and pad daily (clean or
replace).
• Cleanmachine.Ifcompressedairisavailable,
blow dust from machine and engine,
concentratingontheinsideofengineshrouds.
Washundercarriage.CAUTION: Care should
be taken to make sure engine is cool before
water is used to prevent warping and other
damage.
Weekly Maintenance – (every
20 to 50 hours of operation)
• AllDailyMaintenanceservices.
• Changeoilandoilfiltersat50hoursofservice.
Use10W30orSAE30motoroil.Useofnon-
recommendedoilmayvoidtheenginewarranty
(seeengineowner’smanual).
• Check for loose nuts and/or bolts on entire
machine.
• Examineallpropanefuelcomponentsforleaks
orwear.Replaceifnecessary.
• Greasewheels.Useonepumponlyofwhite
lithiumgrease.Moregreasethanrecommended
maypushthesealsanddustcoversout,allowing
dustandotherforeignmaterialstopenetratethe
bearings,thusshorteningtheirlife,aswellas
allowinggreasetodropfromthewheelstothe
floor.
Monthly Maintenance – (every
80 hours of operation)
• Perform all Daily and Weekly Maintenance
services.
• Consult engine owner’s manual for the
following:
» Torque head bolts.
» Check valve clearance.
» Torque valve cover bolts.
» Inspect spark plugs. Replace if necessary.
» Remove engine shroud and clean cooling
fins.
Quarterly Maintenance – (every
250 hours of operation)
• Performallmonthlymaintenanceitems.
• HaveenginecheckedbyanAuthorizedService
Center-includingemissionscheck.
Propane Fuel System
Repairs and adjustments to the fuel system can
onlybemadebyanauthorized,properlytrainedand
certifiedservicetechnician.Improperadjustments
will cause increased toxic emissions of carbon
monoxide andmayresultincarbonmonoxide
Changing the Oil
1. Theenginemanufacturerrecommends10W30
or SAE30 motor oil. ATTENTION: Do not
over fill oil and never run engine with low oil
level.
2. Runengineforfiveminutestowarmtheoil.
3. Makesuremachineisonalevelsurface,with
padrestingonthefloor.Placeacontainerunder
thedrainandopentheoildrainvalve.Allowoil
todraincompletely.
4. Close drain valve and add 1 quart of 10W30
or SAE30 motor oil. Check level and add if
necessary.
5. Replace oil-fill cap assembly. Hand tighten
only.
Checking the Oil Level
Whencheckingoil,removedipstick,wipeclean,
and then reinsert the dip stick into the engine.
Do not screw in for Kawasaki or Robin engines.
Removedipstickandobserveoillevelasindicated
on thedip stick.
Adjusting Belt Tension
Toolsrequired:
» 9/16” (19 mm) open end wrench
»
15/16” (24 mm) deep-well socket
1. Loosenmountingboltontopsideofmachine
deckwhileholdingadjustingnutonunderside
ofdeck.NOTE: The mounting bolt must be
loosened before adjustment can be made.
2. Rotate adjusting nut counter clockwise with
sockettoapplytensiontobelt.
3. While holding the tension on the adjusting
nut,tightenthemountingboltonthetopofthe
deck.
4. Check belt tension by pinching belt together.
Beltshoulddepressonly½”(12mm).
To Order Parts Call 1-888-702-5326 - https://monsterfloorequipmentparts.com