Eagle 680022 Operator's Manual - Stopping The Machine
Eagle Solutions, ©2008, Tracker Operator Manual Page #12
Eagle Solutions, ©2008, Tracker Operator Manual Page #13
4. Allow stripper solution to penetrate as
directed.
5. Begin stripping with the machine (one pass
is generally all that is needed). Move at a
deliberate,steadypace.
6. Keepmachinemoving.Runninginoneplace
formorethanafewsecondsmaydamagethe
floor.
7. Do not leave machine unattended while the
engineisrunning.ATTENTION: It is possible
to damage the engine by allowing it to idle
for long periods of time by affecting proper
lubrication. WARNING! Exhaust emissions
contain harmful toxic gases; the worst being
carbon monoxide. Always make certain that
adequate ventilation is available. Do not
operate the machine in confined areas.
8. When stripping against walls, it is best to
generallykeepthewalltotheoperator’sright
handside.Mosthandedgingmaybeeliminated
or at least minimized by moving slowly with
theTrackeralongwalls.
9. Removesludgewithvacuumrecoverysystem
or auto scrubber. Damp mop floor - rinse
thoroughly.
10. Uponcompletion,followshutdownprocedures
as instructed in operation manual and allow
enginetocometoacompletestop.
11. Raisesplashguardskirtandtighten.
12. Install transport wheel, positioning chain of
transportwheeltowardsfrontofmachine.
13. Turnkeyswitchtooff,ifsoequipped,andplace
keyinsecurelocation.
14. Removestripbrushesorpaddrivers.
Stopping the Machine
1. Putmachineinidlemode.
2. Close the service valve on the fuel cylinder
while the engine is running. This serves to
“purge”thefuelsystemofallflammablegas.
3. Ifequipped,turnthekeyswitchtoOFF.
Emergency Stopping
Incaseofemergency,themachinecanbebrought
toaninstantstopbythefollowingmethods:
»
Release “KILL SWITCH” (if installed).
» Turn key switch to “off” position (if installed).
» Position throttle to “off position.
» Close control valve on fuel cylinder.
Cleaning the Machine
Afteruse,theunderneathoftheTrackermaybe
hoseddownforcleaningbystandingthemachinein
anuprightposition.
1. Removethepropanecylinder.
2. Twooperatorsshouldfirmlygripthefrontofthe
Trackerandliftuntilthemachineisupright.
3. Thestrippingbrushesorpaddriversmaythen
be easily removed and the under belly of the
Trackermaybecleaned.
4. Care should be taken when lowering the
machine;twoorthreeoperatorsmaybeneeded
(itisheavy!).NOTE: An operator should be
stationed by the side of the Tracker when it is
in an upright position to prevent it accidentally
being knocked over. It should never be left
unattended in the upright position.
Storing the Machine
1. RemovethefuelcylinderandstoreinaNFPA
approved propane storage cage outside as
directedbyyourlocalgovernment.
2. Aftertheenginehascooledcompletely,clean
machinethoroughly.
3. Performalldailymaintenancerequirements.
4. Storemachineinacool,dry,secureareawhere
itwillnotbedamagedbyothertraffic.
Transporting the Machine
Whentransportingthemachinefromonejobto
another,securethemachinewiththefuelcylinder
installed and the service valve OFF! Allow the
enginetocooldownbeforeloadingit.
Maintenance
WARNING: Before attempting any maintenance
procedures on the machine, close the service valve
on the fuel cylinder and stop the engine.
Repairsandadjustmentstothefuelsystemmust
be performed by an authorized, properly trained
service technician. To keep the machine in good
workingcondition,simplyfollowthedaily,weekly
andmonthlymaintenanceprocedures.
Keeping the machine clean and free from
accumulateddust,lintandoilallowsfreeairflow
acrosstheengineandpropercooling.Alwaysuse
cleanrecoildustfilters.Thesecanbecleanedby
washing them in flowing water and shaking them
dry. Extra filters may be ordered from Eagle
Solutions at 800.633.0519. Keep a log book of
maintenanceand/orrepairs.
To Order Parts Call 1-888-702-5326 - https://monsterfloorequipmentparts.com