- DL manuals
- Eaton
- UPS
- Powerware 9355
- Installation And Operation Manual
Eaton Powerware 9355 Installation And Operation Manual
Summary of Powerware 9355
Page 1
Powerware 9355 ups 20/30 kva installation and operation manual ®.
Page 2
Powerware, powerware hot sync, abm, and lansafe are registered trademarks and x-slot and connectups are trademarks of eaton power quality corporation. Greenlee is a registered trademark of greenlee textron. Modbus is a registered trademark of modicon. Ecopyright 2006 eaton corporation, raleigh, nc, ...
Page 3
Class a emc statements fcc part 15 note this equipment has been tested and found to comply with the limits for a class a digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a c...
Page 4
Special symbols the following are examples of symbols used on the ups or accessories to alert you to important information: risk of electric shock - indicates that a risk of electric shock is present and the associated warning should be observed. Caution: refer to operator’s manual - refer to your o...
Page 5
Eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com i table of contents 1 introduction 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 safety warnings 5 . . . . . . . . . . . ...
Page 6
Table of contents eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com ii ups startup 71 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Normal mode...
Page 7
Eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 1 chapter 1 introduction the powerware ® 9355 uninterruptible power supply (ups) is a true online, double-conversion, three-phase system that can be used to prevent loss of valuable electroni...
Page 8
Introduction eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 2 providing outstanding performance and reliability, the powerware 9355 ups’s unique benefits including the following: s online ups design with pure sine wave output. The ups fil...
Page 9
Introduction eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 3 s parallel tie cabinet an optional parallel system with up to four upss can be installed to provide a parallel capacity and/or redundant system. This load sharing system provid...
Page 10
Introduction eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 4.
Page 11
Eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 5 chapter 2 safety warnings important safety instructions save these instructions this manual contains important instructions that you should follow during installation and maintenance of the...
Page 12
Safety warnings eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 6 consignes de sécurité consignes de sÉcuritÉ importantes conserver ces instructions ce manuel comporte des instructions importantes que vous êtes invité à suivre lors de tout...
Page 13
Safety warnings eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 7 advertencias de seguridad instrucciones de seguridad importantes guarde estas instrucciones este manual contiene instrucciones importantes que debe seguir durante la instala...
Page 14
Safety warnings eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 8.
Page 15
Eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 9 chapter 3 ups setup this chapter describes: s equipment inspection s floor loading and clearances s removing and replacing the cabinet doors s unloading the cabinet(s) the instructions are ...
Page 16
Ups setup eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 10 removing and replacing the front doors to remove and replace the ups or options cabinet front door, see the following section. To remove and replace the extended battery cabinet ...
Page 17
Ups setup eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 11 ebc front door to remove the ebc front door: 1. Remove the two m8 hex-head screws from the top corners of the door (see figure 3). 2. Lift the door up and off the cabinet. To rep...
Page 18
Ups setup eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 12 unloading the cabinet(s) the following tools are required for unloading the cabinet(s): s 15 mm wrench or socket s 7 mm nut driver or socket s adjustable wrench or channel-locks ...
Page 19
Ups setup eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 13 3. Remove the three m10 bolts securing the rear shipping pad to the pallet and remove the shipping pad (see figure 5). Shipping pad m10 bolts figure 5. Removing the shipping pad ...
Page 20
Ups setup eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 14 4. Remove the front door to access the front shipping bracket (see page 10). 5. Remove the four m8 screws securing the front shipping bracket to the cabinet (see figure 6). 6. Re...
Page 21
Ups setup eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 15 note be sure to support the front and back of the cabinet when rolling it off the pallet to prevent tipping or rolling away. 8. Raise the leveling feet so that they do not touch ...
Page 22
Ups setup eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 16 10. With the cabinet supported, slowly pull the pallet away from the cabinet (see figure 9). Figure 9. Removing the pallet (ups shown) 11. Roll the cabinet to the desired locatio...
Page 23
Eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 17 chapter 4 joining the cabinets if you are installing additional cabinets to the ups, join the cabinets before installing the electrical connections between the cabinets. To join the cabine...
Page 24
Joining the cabinets eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 18 edge grommet for options cabinet ebc options cabinet ups figure 10. Joining additional cabinets (typical configuration) 11. Remove the two ground straps from the rear ...
Page 25
Joining the cabinets eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 19 rear ground strap front ground strap figure 11. Ground strap installation.
Page 26
Joining the cabinets eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 20
Page 27
Eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 21 chapter 5 electrical installation the powerware 9355 has the following power connections: s 3-phase (l1, l2, and l3), neutral, and ground connection for rectifier/bypass input s 3-phase (l...
Page 28
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 22 battery circuit breaker wiring access cover input circuit breaker output circuit breaker (optional) figure 12. Ups front view.
Page 29
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 23 10. If you have an options cabinet, remove the front door (see page 10). 11. Remove the options cabinet wiring access cover and retain (see figure 13). 12. If you h...
Page 30
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 24 wiring installation wire the ups or options cabinet(s) according to one of the following configurations: s ups only — see the following section, “ups only wiring” s...
Page 31
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 25 ups only wiring to hardwire the ups: 1. Remove the ups conduit landing box from the rear panel and retain (see figure 14). 2. Punch two holes in the conduit landing...
Page 32
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 26 parallel ups wiring to hardwire the ups in a parallel capacity and/or redundant system: 1. Remove the ups conduit landing box from the rear panel and retain (see fi...
Page 33
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 27 9. Wire the ac input to the bypass breaker on the tie cabinet (see figure 16). Neutral line 1 ground line 2 line 3 maintenance bypass wiring to ups tb4 figure 16. B...
Page 34
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 28 options cabinet with mbs wiring to hardwire an options cabinet with an mbs (with or without an input isolation transformer): 1. Remove the options cabinet conduit l...
Page 35
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 29 maintenance bypass auxiliary contacts input l1 l1 l2 l3 n n output l1 l2 l3 n n input l1 l1 l2 l3 output l1 l2 l3 n n options cabinet with mbs only options cabinet ...
Page 36
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 30 options cabinet with dual-feed wiring to hardwire the options cabinets in a dual-feed system: 1. Remove the options cabinet conduit landing box from both options ca...
Page 37
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 31 maintenance bypass auxiliary contacts input l1 l1 l2 l3 n n output l1 l2 l3 n n input l1 l1 l2 l3 first options cabinet with mbs only second options cabinet with re...
Page 38
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 32 options cabinet with output transformer wiring to hardwire the options cabinets for 480v loads: 1. Remove the options cabinet conduit landing box from both options ...
Page 39
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 33 output l1 l2 l3 n n maintenance bypass auxiliary contacts input l1 l1 l2 l3 n n output l1 l2 l3 n n first options cabinet with mbs only second options cabinet with ...
Page 40
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 34 wiring specifications and diagrams note input neutral must be wired for proper operation or the ups will not start. If you have an options cabinet with an input iso...
Page 41
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 35 jumpers (remove three wires for dual-feed) input terminal block l1, l2, l3, n, n output terminal block l1, l2, l3, n, n remote dc (battery) dc +, dc – maintenance b...
Page 42
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 36 figure 22. Ups wiring diagram (single-feed, 208v or 220v input : 208v or 220v output).
Page 43
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 37 figure 23. Ups with ebcs wiring diagram (single-feed, 208v or 220v input : 208v or 220v output).
Page 44
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 38 figure 24. Ups and options cabinet with mbs only (single-feed, 208v or 220v input : 208v output).
Page 45
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 39 figure 25. Ups and options cabinet with mbs/input isolation transformer wiring diagram (single-feed, 208v, 480v, or 600v input : 208v output).
Page 46
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 40 figure 26. Ups and dual-feed options cabinets wiring diagram (dual-feed, 208v, 480v, or 600v input : 208v output).
Page 47
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 41 figure 27. Ups and options cabinet with output transformer wiring diagram (single-feed, 480v input : 480v output).
Page 48
Electrical installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 42 figure 28. Parallel ups system with tie cabinet diagram (single-feed, 208v or 220v input : 208v or 220v output).
Page 49
Eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 43 chapter 6 extended battery cabinet installation note a maximum of four extended battery cabinets (ebcs) can be installed. To install the optional ebc: 1. Remove the ups front door (see pag...
Page 50
Extended battery cabinet installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 44 ups battery connector ebc battery connector ebc cable ups battery circuit breaker figure 29. Typical ebc installation.
Page 51
Eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 45 chapter 7 permanent mounting installation note permanent mounting is optional and uses the rear shipping bracket. To permanently mount the cabinet(s): 1. Lower the leveling feet to prevent...
Page 52
Permanent mounting installation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 46 figure 31. Permanent mounting.
Page 53
Eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 47 chapter 8 communication this section describes the: s db-9 communication port s x-slot cards s remote monitor panel (rmp) and industrial relay card (irc) s powerware lansafe ® power manage...
Page 54
Communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 48 installing communication options and control terminals note to install a can bridge card, see “parallel communication” on page 61. To access and install the communication opt...
Page 55
Communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 49 4. Route the cable(s) through the opening between the two x-slot communication bays. Communication opening figure 34. Routing the cables 5. Remove the communication wiring ac...
Page 56
Communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 50 communication options the powerware 9355 has serial communication capabilities through the db-9 communication port or through an x-slot card in one of the available bays. In ...
Page 57
Communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 51 x-slot cards for information about the powerware hot sync can bridge card, see “parallel communication” on page 61. X-slot cards allow the ups to communicate in a variety of ...
Page 58
Communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 52 remote monitor panel the optional rmp can be installed to monitor the operation of the ups from virtually any location within your facility, up to 500 ft (152.4m) from the up...
Page 59
Communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 53 mounting slots (6 places) note matches mounting holes on a single- or double-gang electrical box. Cable exit openings for 1/2” conduit or provided strain relief (3 places) di...
Page 60
Communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 54 table 3. Rmp wire terminations from rmp terminal to irc terminal remarks j1-1 j1-1 j1-3 j1-3 j1-4 j1-4 use beldon 8690 060 or equivalent cable j1-5 j1-5 equivalent cable j1-6...
Page 61
Communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 55 industrial relay card the irc uses normally-open or normally-closed dry relay contacts to indicate the ups status as listed in table 4. Figure 41 shows an irc. Plug-in termin...
Page 62
Communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 56 table 4. Irc wire terminations irc terminal function remarks j2-1 nc j2-2 com normal mode j2-3 no j2-4 nc j2-5 com bypass mode j2-6 no yp j2-7 nc j2-8 com battery mode j2-9 n...
Page 63
Communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 57 control terminals the cables should be connected to the control terminals with a mating connector. Input and output terminals have a functional isolation from terminal to ter...
Page 64
Communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 58 c a u t i o n s the repo must not be connected to any utility connected circuits. Reinforced insulation to the utility is required. The repo switch must have a minimum rating...
Page 65
Communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 59 programmable signal inputs the ups incorporates two programmable signal inputs (see figure 32 on page 47). Use of non-polar (relay) control input is recommended. The pins mus...
Page 66
Communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 60
Page 67
Eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 61 chapter 9 parallel communication the powerware hot sync can bridge card, shown in figure 43, can be installed to provide connectivity for operational mode control and metering of a paralle...
Page 68
Parallel communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 62 4. Set the jumper pins on the powerware hot sync can bridge card according to the parallel configuration (see figure 45): s if only two upss are paralleled, then set...
Page 69
Parallel communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 63 8. Route the wiring through the conduit from the communication wiring access plate to the opening between the two x-slot communication bays on each ups (see figure 4...
Page 70
Parallel communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 64 10. Route the pull-chain wiring through the middle of the fan section and secure in the cable clips for each ups (see figure 47). Figure 47. Installing communication...
Page 71
Parallel communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 65 11. Wire the pull-chain wiring to signal input 2 on each ups and daisy chain the wiring to each ups as shown in figure 48. Be sure to check correct polarity: s conne...
Page 72
Parallel communication eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 66 alarm 1alarm 2bpo rs232 relay output pull chain outp parallel only x27 x57 x43 x--np x52--nc x45 x44 alarm 1alarm 2bpo rs232 relay output pull chain outp parallel on...
Page 73
Eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 67 chapter 10 operation this chapter contains information on how to use the powerware 9355, including front panel operation, ups startup and shutdown, and configuring the ups for extended bat...
Page 74
Operation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 68 display functions as the default or after 15 minutes of inactivity, the lcd displays the selectable startup screen. The default is the eaton powerware logo and can be changed to ...
Page 75
Operation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 69 user settings the following table displays the options that can be changed by the user. Note changes to the output voltage or frequency options should be made before turning on t...
Page 76
Operation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 70 table 7. User settings (continued) default setting available settings description user password enabled/disabled if enabled is selected, the password is user. Disabled audible al...
Page 77
Operation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 71 ups startup w a r n i n g only qualified service personnel (such as a licensed electrician) should perform the ups installation and initial startup. Risk of electrical shock. Ver...
Page 78
Operation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 72 starting the ups on battery note before using this feature, the ups must have been powered by utility power at least once. To start the ups on battery: 1. Remove the ups front do...
Page 79
Operation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 73 internal bypass startup to start the ups in internal bypass mode: 1. Remove the ups front door (see page 10). 2. Verify that the maintenance bypass switch is in the ups position ...
Page 80
Operation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 74 configuring the ups for ebcs note each ups in a parallel system must have its own ebc and the same number of ebcs to ensure consistent runtimes. To ensure maximum battery runtime...
Page 81
Operation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 75 parallel operation initial startup must be performed by an authorized eaton customer service engineer. This section describes shutting down and restarting upss in a parallel syst...
Page 82
Operation eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 76 restarting the parallel system to restart the parallel system: 1. Verify that all ups breakers on the tie cabinet are in the off position. 2. Switch on utility power where the up...
Page 83
Eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 77 chapter 11 ups maintenance this section explains how to: s care for the ups and batteries s recycle used batteries or ups s use the maintenance bypass switch (mbs) s use parallel bypass up...
Page 84
Ups maintenance eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 78 when to replace batteries when the indicator flashes and the lcd panel displays battery failure, the batteries may need replacing. Contact your service representative to or...
Page 85
Ups maintenance eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 79 using the ups maintenance bypass switch the ups maintenance bypass switch is located behind the ups front door (see figure 51). The maintenance bypass switch is used to byp...
Page 86
Ups maintenance eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 80 single ups bypass to transfer the load from the ups to maintenance bypass: 1. Remove the ups front door (see page 10). 2. Turn the maintenance bypass switch to the bypass p...
Page 87
Ups maintenance eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 81 parallel ups bypass to switch the parallel ups to maintenance bypass from normal mode: 1. From any ups, set the system to internal bypass mode: s using the button on the fr...
Page 88
Ups maintenance eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 82.
Page 89
Eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 83 chapter 12 specifications this section provides the following specifications: s model list s dimensions and weights s environmental and safety specifications s technical specifications s m...
Page 90
Specifications eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 84 table 10. Environmental and safety specifications operating temperature 50°f to 104°f (10°c to 40°c) optimal battery performance: 77°f (25°c) transit temperature -13°f to 13...
Page 91
Specifications eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 85 table 12. Model specifications 20 kva model output voltage (line–line) 208 208 208 220 output voltage (line–neutral) 120 120 120 127 input voltage 208 480 (with input isolat...
Page 92
Specifications eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 86 table 14. Battery runtimes (in minutes) at full load, 0.9 pf load ups internal batteries +(1) ebc 36 +(2) ebc 36 +(3) ebc 36 30 kva/27 kw 10 31 56 75 20 kva/18 kw 18 56 82 9...
Page 93
Eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 87 chapter 13 troubleshooting the powerware 9355 is designed for durable, automatic operation and also alerts you whenever potential operating problems may occur. Usually the alarms shown by ...
Page 94
Troubleshooting eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 88 action possible cause alarm or condition the ups does not start. The main utility breaker is off. Verify that the main utility breaker is on. The input circuit breaker is o...
Page 95
Troubleshooting eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 89 service and support if you have any questions or problems with the ups, call your local distributor or the help desk at one of the following telephone numbers and ask for a...
Page 96
Troubleshooting eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 90
Page 97
Eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 91 chapter 14 limited warranty warrantor: the warrantor for the limited warranties set forth herein is eaton power quality corporation, a delaware corporation (“eaton”). Limited warranty: thi...
Page 98
Limited warranty eaton powerware ® 9355 ups (20/30 kva) installation and operation manual s 164201626 rev b www.Powerware.Com 92.
Page 100
*164201626b* 164201626 b.