Eclipse AVN827GA Installation Manual - page 3
Select the screws in accordance with the shapes of the
screw holes in the mounting bracket.
⑦ Hexagonal head bolt
(Red:M5 x 8) x 8
5
7
1
Flat head screw
(Red:M5x8) x 8
⑧
4
Mounting bolts
Pocket, etc
Center cluster panel
Attach a splicing connector at this location.
Reverse signal wire
Reverse lamp
Reverse signal wire
Connecting point for the reverse signal (example)
Use a splicing connector to connect the reverse signal wire (Violet/White) coming from the main unit to the reverse signal wire of the vehicle.
1
Route the reverse signal wire to the main unit.
2
・ Be sure to connect the reverse signal wire. If it is not connected, when reversing the vehicle, the position of the vehicle may be different to that displayed
on the navigation screen.
・ Use a circuit tester to confirm that a sensing voltage of 6V or higher is generated when the selector lever is in reverse.
Tip
2
Route the parking brake signal wire to the main unit.
Connecting point for the parking brake signal (example)
1
Use a splicing connector to connect the parking brake signal wire (Light Green) coming from the main unit to the parking brake signal wire of the
vehicle.
Notes on installation
・ Check the speed pulse signal, parking brake signal and reverse signal carefully before making the connections. If the wires are incorrectly connected,
accidents or problems with correct operation may result.
・ The locations of the speed pulse signal wire, parking brake signal wire and reverse signal wire may vary depending on the vehicle model and grade.
Ask the car dealer or your nearest ECLIPSE dealer for details.
Press the “AUDIO” button and then touch “INFO”.
4
Press the
button to open the display, and then insert the map SD card into the main unit.
2
Insert the ignition key into the vehicle and start the engine.
1
1
5
・ Do not turn the ignition key to ACC OFF or operate the main unit until the navigation screen appears.
・ Check that the shift position is correct and that the area around the vehicle is safe before starting the engine.
Tip
5
Touch “SYSTEM CHECK” and check the connection status for each signal.
4
Attach the brackets to the main unit.
4
Install the main unit in the vehicle.
5
Mounting bracket
・ Carefully bind any excess length of wire that is connected to the main unit and secure it to an area of empty space in the vehicle so that it does not
dislodge or interfere with the main unit or vehicle-side equipment. If the wires are not handled correctly, operating problems or short-circuits may occur,
and this may result in the danger of fire or other accidents.
・ Connect all wires before installing the main unit.
・ Be sure to use the supplied accessory mounting screws (Red: M5 x 8) as the mounting screws. If any other screws are used, they may damage the
inside of the main unit.
Tip
・ Do not peel off this protective label before finishing installation and checking operations.
Tip
Panel protective sheet
2
Route the vehicle speed pulse signal wire to the main unit.
Connecting point for the vehicle speed pulse signal (example)
1
Use a splicing connector to connect the vehicle speed pulse signal wire (Pink) coming from the main unit to the vehicle speed pulse signal wire of the
vehicle.
・ Always be sure to connect the vehicle speed pulse, otherwise the measurement precision will be greatly reduced.
Tip
Vehicle speed pulse
signal wire (vehicle harness)
Engine computer
Vehicle speed pulse signal wire
(Pink) of connection cable
Splicing connector
Parking brake signal wire
Attach a splicing connector at this location.
Parking brake signal wire
Hand-operated parking brake
Foot-operated parking brake
Press the
button to close the display.
・ After the program has finished loading, follow the directions on the screen to display the map screen.
3
2 3
・ Be careful not to press hard on the main unit display or the buttons when installing the main unit to the vehicle, otherwise the display and buttons may
become damaged.
Tip
Remove the pocket and any other accessories from the center cluster to make room for the main unit.
2
Remove the mounting brackets for the pocket.
3
♦Connecting the vehicle speed pulse, parking brake and reverse wires
♦Connecting the vehicle speed pulse, parking brake and reverse wires
♦Checking operation after installation
♦Checking operation after installation