DL manuals
Economix
Toy
Zlin Z-526 AFS
Instruction Manual

Economix Zlin Z-526 AFS Instruction Manual

Page of 8

Download

Print this page

Bookmark us

Zlin Z-526 AFS

Specification:

Length :1875 mm(73.8")

Wing Span :2085 mm(82")

Wing Area :76.2sq.dm

8.19sq.ft

Wing Loading :70.9g/sq.dm

23.2oz/sq.ft

Flying Weight :5.4kg(11.9lbs)

Radio :6ch & 8servos

Engine: :26cc-36cc

SAFETY PRECAUTIONS

INSTRUCTION MANUAL

First-time builders should seek advice from people having building

experience.If misused or abused,it can cause serious bodily injury

and damage to property.

Fly only in open areas and preferably at a dedicated R/C flying site.

We suggest having a qualified instructor carefully inspect your

airplane before its first flight.Please carefully read and follow all

instructions included with this airplane,your radio control system

and any other components purchased separately.

(The people under 18 years old is forbidden from flying this model)

This R/C airplane is not a toy!

1 2 3 4 5 6 7 Next › »

Summary of Zlin Z-526 AFS

Page 1
Zlin z-526 afs specification: length :1875 mm(73.8") wing span :2085 mm(82") wing area :76.2sq.Dm 8.19sq.Ft wing loading :70.9g/sq.Dm 23.2oz/sq.Ft flying weight :5.4kg(11.9lbs) radio :6ch & 8servos engine: :26cc-36cc safety precautions instruction manual first-time builders should seek advice from p...
Page 2
: 4-cycle .120 15 " x7 6 (with 8 servos), 6 6 6 channel radio for aiplane is highly recommended for this model. Warning remove the covering with proper pressure to cut through only the covering itself.Otherwise, cutting down into the balsa structure may weaken the model part and cause accident. The ...
Page 3
Washer (3x6mm) 2 2 accessory list for the coming installation steps. Accessory list for the coming installation steps. Mount the receiver and the battery to appropriate position in the fuselage. Screw (3x16mm) 4 tp screw (2.3x12mm) fix the fuselage top cover to the fuselage with screws as illustrati...
Page 4
31 tp screw (2.3x12mm) screw (4x20mm) screw (4x35mm) screw (2x10mm) screw (3x16mm) 2 2 2 collar (2mm) 5 collar (3mm) 2 collar (5mm) 2 6 6 6 nut(2mm ) nut(3mm ) 6 washer(2x6mm) washer(3x6mm) washer(4x8mm) washer(6x12mm) 6 2 2 1 1 12 2 1 1 4 4 screw (6x35mm) 2 2 4 blind nut(4mm) wheel(100mm) wheel(45m...
Page 5
5.2mm blind nut 4 blind nut (4mm) 1 linkage stopper 12 4 washer(4x8mm) screw (4x45mm) 2 4 screw (4x20mm) 4 plastic tube (2x400mm) fuel tank (550cc) 1 1 cable tie 2 rod (2x200mm) blind nut (4mm) the front view once the engine install completion. The side view once the engine install completion. 162mm...
Page 6
Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! 8 2 2 rod (2.5x300mm) tp screw (2.3x12mm) servo tray(70x58x2mm) pivot&round hinge(4.5x67mm) 8 install the aileron servo to the servo mount as illustration below. Install the control ...
Page 7
1mm trailing edge cut away the rubber tube when the epoxy glue dried. Make sure they are in the right position while installing. Keep some space about 1mm width between the rudder and tail edge. Epoxy the pivot & round hinges to the rudder,drill holes to appropriate position in the rudder and assemb...
Page 8
Make sure hinges are mounted in the same line. Apply instant type ab glue to appropriate position of the elevator and pivot & round hinges. Insert the pivot & round hinges to the elevator. 1mm trailing edge cut away the rubber tube when the epoxy glue dried. Make sure they are in the right position ...