ECX ECX03006 Instruction Manual - page 10
10
EN
RUCKUS
SHOCK CLEANING
Oil-fi lled shocks will require regular maintenance due to the
oil breaking down or getting dirty. This maintenance should be
performed after about every 3 to 5 hours of use, depending on
the conditions that the vehicle is used in.
• Remove the shock from the vehicle.
• Remove the cap from the shock body and dispose of fluid.
• Disassemble the shock. Clean thoroughly with DYN5505. Dry
parts before assembly.
• Re-assemble the shock and refill the shock body with silicone
fluid (30 weight recommended).
• Slowly move the shaft and piston up and down to remove air
bubbles.
• Move the piston to the midway point of the body and install
the cap.
• Wipe off any overflowing fluid.
• When properly filled, the piston should rebound about 3/8 in
(9.5mm) after being pushed in fully.
• Re-install the shock on the vehicle.
Ride Height Adjustment
Ride height is an adjustment that affects the way the vehicle
jumps, turns and goes over bumps. Drop one end of the
vehicle from approximately 6 inches (152 mm) in height onto
a fl at surface. When dropping the front of the vehicle, after
the vehicle settles, make sure the front arms are equal and
parallel to the fl at surface. Do the same with the rear to make
sure both arms are parallel with the fl at surface.
Lowering the front ride height increases steering, but
decreases traction. Lowering the rear ride height increases
traction, but decreases steering.
Part #
Description
ECX1036
Shock Body Set
ECX1037
Shock Caps, Pistons
ECX1038
Shock Parts Set
ECX1039
Front Shock Shaft (2)
ECX1040
Rear Shock Shaft (2)
ECX1041
Front Shock Springs (2)
ECX1042
Rear Shock Springs (2)
ECX1043
Shock O-Ring Set
No. Description
TAPPING
BINDER HEAD
M3x10mm
TAPPING
BINDER HEAD
M3x12mm
TAPPING
FLAT HEAD
M3x15mm
TAPPING
FLAT HEAD
M3x12mm
TAPPING
FLAT HEAD
M3x10mm
TAPPING
BINDER HEAD
M3x18mm
TAPPING
FLAT HEAD
M2x16mm
TAPPING
BINDER HEAD
M3x16mm
No. Description
WASHER
5x7x0.5mm
E-CLIP E2.5
LOCK WASHER
FLANGED
LOCK NUT M4
WASHER
3x8x0.5mm
LOCK NUT M3
WASHER
2x7x0.5mm
SET SHAFT
SCREW
M3x13mm
No. Description
SETSCREW
M3x3mm
SETSCREW
M3x12mm
STEP SCREW
M3x0.5x13.4mm
STEP SCREW
M3x0.5x10.5mm
BUTTON
HEX
M2.5x4mm
BUTTON
HEX
M2.5x8mm
STEP SCREW
M3x0.5x7.4mm
No. Description
BINDER
HEAD
M3x8mm
BINDER
HEAD
M3x12mm
BINDER
HEAD
M3x20mm
BINDER
HEAD
M3x25mm
REAR SHOCK
FRONT SHOCK
ECX1043
ECX1037
ECX1037
ECX1041
ECX1037
ECX1043
ECX1036
ECX1038
ECX1038
ECX1043
ECX1037
ECX1037
ECX1038
ECX1042
ECX1040
ECX1057
ECX1037
ECX1043
ECX1038
ECX1039
ECX1036
ECX1038
ECX1038
ECX1037
ECX1057
FASTENERS