EYEZONE P102-8 User Manual

Summary of P102-8

  • Page 1

    Eyezone p102-8 user manual oct 26, 07 3 4 4 1 2 f 1 3 fcc notices it’s herewith confirmed to comply with the requirements of fcc part 15 rules. Operation is subject to the following two conditions: z this device may not cause harmful interference. Z this device must accept any interference received,...

  • Page 2

    1. Package contents……………………..…………………….. 1 2. Introduction………………………………….……………... 1 3. Features…………………………………..………………… 1 4. Hardware overview…………………………….…………... 2 5. Remote control…………………………………………….. 3 6. Setting up……………………………………..……..…….. 4 6.1 slide setup……………………………………..…. 4 6.2 music setup…………….…………...

  • Page 3

    2 multi-language osd:english, french, german, italian, portuguese, spanish, netherlands, japanese and chinese. Supports slide show function: with 14 kinds of transition effects. Supports slide time (interval) mode:interval time with 1, 3, 5, 10, 30, 60 seconds. Supports music slide show:music and pi...

  • Page 4

    4 press the “setup” button on the remote control to open the “setup menu – main page” shown in the following figure. There are five groups of sub-menu in the setup menu. Use the “▲、▼、 ▲ 、 ▼ ” buttons to select an item or to adjust values, and use the “enter” button to go into the function or to conf...

  • Page 5

    6 copy files (music, picture and movie) to the memory card first. 7.1 play picture file step 1: press the “slide” button on the remote control from any menu. Step 2: the preview mode will show all the picture files on the memory card. Use the “▲、▼、 ▲ 、 ▼ ” buttons to select the picture file, and pre...

  • Page 6

    8 7.3 play movie file step 1: press the “movie” button on the remote control from any menu. Step 2: the preview mode will show all the video files on the memory card. Use the “▲、▼、 ▲ 、 ▼ ” buttons to select the movie file, and press the “enter” button to play the movie file. Step 3:press the “next” ...

  • Page 7

    10 „ copy the media files that you want play to the memory card. The bar-code and the name of the corresponding file must be the same. For example:bar-code is 1234567, and names the corresponding file “1234567.Xxx”. (xxx is the extension) „ make sure the “scanner” function is enabled first. “slidesh...

  • Page 8

    12 code 39 enable code 39 disable 13 codabar enable codabar disable.

  • Page 9

    14 upc/ean/jan enable upc/ean/jan disable 15 itf 2 of 5 enable itf 2 of 5 disable.

  • Page 10

    16 chinese post code enable chinese post code disable 17 code 128 disable.

  • Page 11

    18 code 93 enable code 93 disable 19 ean-128 enable ean-128 disable.

  • Page 12

    20 code 32 enable (italian pharmacy code) code 32 disable (italian pharmacy code) 21 msi enable msi disable.

  • Page 13

    22 ean-13 convert to isbn/issn enable ean-13 convert to isbn/issn disable 23 upc/ean add on off add on 5 only.

  • Page 14

    24 add on 2 only add on 2 or 5 25 ean/upc +add on (none mandatory) ean/upc + add on ( mandatory).

  • Page 15

    26 force upc-a to ean-13 format enable force upc-a to ean-13 format disable 27 situation check point no picture 1. Check if the power supply is connected. 2. Make sure the p102-8 is turned on. No response from the remote control 1. Make sure there is a clear view between the remote control and the d...