January, 200 4 412 o pe rator and 455 d control panel inst allation manual contents t h e 4 1 2 o p e r a t o r a n d 4 5 5 d c o n t r o l p a n e l : i n s t a l l a t i o n m a n u a l faac international, inc. 303 lexington avenue cheyenne, wy 82007 www.Faacusa.Com important safety information 2 ...
Page 2 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual both the installer and the owner and/or operator of this system need to read and understand this installation manual and the safety instructions supplied with other components of the gate system. This information sh...
Page 3 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual 6. It is extremely unsafe to compensate for a damaged gate by increasing hydraulic pressure. 7. Devices such as reversing edges and photobeams must be installed to provide better protection for personal property and...
Page 4 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual t echnical d ata t he 412 c ompact o perator parameter measure voltage required 1 , vac 115, +/–10%, 50-60 hz 230, +6 or -10%, 50-60 hz duty type residential duty maximum duty cycle 2 18 cycles/hr 30 cycles/hr maxim...
Page 5 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual u npacking the o perator when you receive your 412 compact operator, complete the following steps. Inspect the shipping box for physical damage such as a torn carton. Then inspect the operator after you remove it fr...
T he 412 c ompact o perator g eneral c haracteristics the faac 412 compact operator is an automatic gate operator for a swinging gate leaf. The 412 compact operator is useful in apartment and other residential applications and can accommodate a gate leaf up to 14 ft (4.3 m) long. The self-contained ...
M anual r elease m echanism the manual release mechanism is a built-in release device of the 412 operator (see figure 4). To access the keyhole, remove the plug on the top of the motor housing. Then insert the key and turn it a half turn in the direction of the gate’s closing to disengage the operat...
Page 8 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual outward swinging gate: if you are installing the 412 operator to swing the gate outward, construct a steel elbow of sufficient size to attach to the gate pillar and rear mounting bracket (see figure 7 for elbow dime...
Page 9 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual a ttach the f ront m ounting b racket to the g ate l eaf disengage the operator’s worm screw drive from its motor with the manual release. Insert the key in the top of the motor assembly, and turn the key a half tur...
Page 10 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual i nstalling the 455 d c ontrol p anel locate the control panel enclosure in the most convenient position possible, considering the movement of the gate. Figure 12 shows a basic layout for a two- leaf gate with the ...
1 5 3 6 8 2 4 9 7 3 5 1 a a b a b c c d a figure 12. The layout of a sample gate system locate switches at least 10 ft from the gate page 11 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual 1 operator wire gauges for given voltage 2 control panel 220 vac 115 vac 3 photoc...
Page 12 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual the 412 compact operator.
Page 13 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual parts list 412 compact operator pos part no. Description qty 1 799360 motor housing, sx top section 1 1 799359 motor housing dx top section 1 2 713009 manual release key, 412 1 3 7171345 flange, protective cover, 4...
T he 455 d c ontrol p anel g eneral d escription the faac 455 d control panel is used to operate the following models. Swing gate operators: 400 412 402 750 422 760 barrier gate operators: 610/615 the 455 d programming controls the following: operating logic: a, s, e, ep, b, and c logics available. ...
Page 15 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual t he 455 d c ontrol p anel i nstallation i nstructions ra di o 1-455d115 = 115v 1-455d = 230v f2 f1 m m k + op - cl +24 v fsw nc - b - stop a + tx fsw w. L. Lock 9 10 11 12 13 14 15 16 17 18 19 22 23 24 25 lamp com...
Note: in order to c omply with ul 325, two s ets of faac photobeams mus t be ins talled. One s et s hould be 6 in. Outs ide the c los ed gate(s ) and ac t as a c los ing rev ers ing dev ic e. Another s et s hould be 6 in. Bey ond the s wing of the gate(s ) and ac t as an opening rev ers ing dev ic e...
F sw o p f sw c l o p_ a o p_ b st o p f c a1 f c a2 f c c 1 f c c 2 fswop fswcl op_a op_b stop fca1 fca2 fcc1 fcc2 this display shows the normal status of the control panel. This display shows the meaning of each led. Figure 16. The 455 d display. Page 17 january, 200 4 412 o pe rator and 455 d con...
• e (semi-automatic): this mode requires a command to open and a command to close. A second command during opening stops the gate. A second command during closing reopens the gate. • ep (semi-automatic, step by step): this mode requires a command to open and a command to close. A second command duri...
Page 19 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual magnetic lock shadow loop rev ersing photocells (f or closing) 3 & 4 wire radio receiv ers n.C. N.O. Com n.C. N.O. Com 17 14 18 21 12 vac relay + - lock 12 19 7 8 nc c coil voltage = motor voltage additional revers...
Page 20 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual p rogramming to program the automated system, the “programming mode” must be accessed. Programming is split into two parts: basic and advanced. B asic p rogramming to access basic programming, press the “f” key. • ...
Page 21 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual t he 455 d c ontrol p anel i nstallation i nstructions i ndicator -l icht : if 0 is selected, the output func- tions as a standard indicator-light (lit at opening and pause, flashing at closing, and off when gate c...
• when gate operator (1) reaches the position that you want it to slow down, an open command must be given to start the slow down phase. • when gate operator (1) reaches the positive stop and the desired motor run time has been reached, an open command must be given to shut the motor off. At this po...
Page 23 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual t he 455 d c ontrol p anel i nstallation i nstructions the procedure has ended and the gate is ready to operate, using default slow down automatically set by the control panel. C omplete l earning n otes : • if onl...
T he 455 d c ontrol p ane l i ns tallat ion i n struc ti on s page 24 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual a (automatic) logic (455 d) gate status open a open b stop opening reversing device(s) closing reversing device(s) warning light closed opens both leave...
Page 25 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual e (semi-automatic) logic (455 d) gate status open a open b stop opening reversing device(s) closing reversing device(s) warning light closed opens both leaves opens single leaf connected to motor 1 no effect no eff...
January, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual t he 412 o perator the faac 412 operator requires no maintenance. Periodically inspect the operator, however, to ensure continued proper operation. T he 455 d c ontrol p anel keep the control panel free from spider webs, i...
Page 27 january, 200 4 412 o pe rator and 455 d control panel i nst allatio n m anual t roubleshooting p roblem : t he gate does not respond to an activating signal . S olution : you should have at least one operator wired to terminals 1,2 and 3. Be sure that you have the motor start capacitors wire...
To the original purchaser only: faac international, inc., warrants, for twenty-four (24) months from the date of invoice, the gate operator systems and other related systems and equipment manufactured by faac s.P.A. And distributed by faac international, inc., to be free from defects in material and...
