Summary of Advance
Page 1
Page 1 of 22 10/11/2009 technical manual dish washer “advance” csi instalaciones.
Page 2
Page 2 of 22 10/11/2009 platform the platform used for controlling the low range, advance dishwasher (front loading, top loading and glasswasher) is shown below. Advance serigraphy main control card temperature card card assembly csi instalaciones.
Page 3
Page 3 of 22 10/11/2009 as can be seen from the picture, the platform has 2 cards, the main controller card and the auxiliary temperature card, in addition to a membrane keyboard with 4 buttons and 5 leds permitting interaction with the appliance. Temperature card the temperature card is powered thr...
Page 4
Page 4 of 22 10/11/2009 the configuration of the dip-switches is as follows: o dip1: door o if dip1=0 glass washer and front loading. To begin a new wash cycle, select the required programme, the appliance is on stand-by meanwhile o if dip1=1 top loading: to start a new wash cycle, just open and...
Page 5
Page 5 of 22 10/11/2009 fagor electronic advance model dip1 dip2 dip3 dip4 cycle times (s) other glasswasher models off off off off ad-15 d , ad-21 d off on off off p1=90 / p2= 120 / p3=180 other glasswasher models a.F. Off off on off ad-48 d, ad-64 d off on on off ad-48 hy, ad-64 hy off off on on p...
Page 6
Page 6 of 22 10/11/2009 dips on off csi instalaciones.
Page 7
Page 7 of 22 10/11/2009 interface one of the possible serigraphic combinations (membrane keyboard) is shown below. This has been designed to interact with the 5 relay card. These are the components of the above combination: b1 (on/off button) o button for switching appliance on/off. The button shoul...
Page 8
Page 8 of 22 10/11/2009 l2 (led p1) o if the appliance is washing, this led remains lit. It is also lit if the appliance is in pause mode, i.E., if the door has been opened o if the descaler or drainage pump function is activated, the led flashes o if the appliance is not washing, this led is off. B...
Page 9
Page 9 of 22 10/11/2009 b4 (button p3) o if this button is pressed once, the dishwasher starts to wash with programme 3 o if the button is pressed for 3 seconds, this activates the function corresponding to the right icon (cold rinse or indefinite cycle, depending upon the dip1 configuration) o if d...
Page 10
Page 10 of 22 10/11/2009 general operation to switch on the appliance, press button b1 (button on/off), when the required programme button is pressed the dishwasher starts, provided that the tank has been filled with water. When the programme is selected the machine starts and runs for the time esta...
Page 11
Page 11 of 22 10/11/2009 diagnostics the software should also diagnose any faults, informing of the action via impulse trains of the on/off led. The trains are formed of x 0.5” impulses (on) and a wait of 2”, as shown in the diagram below. Example of a 2-impulse train the diagnostics defined are lis...
Page 12
Page 12 of 22 10/11/2009 csi instalaciones.
Page 13
Page 13 of 22 10/11/2009 csi instalaciones.
Page 14
Page 14 of 22 10/11/2009 csi instalaciones.
Page 15
Page 15 of 22 10/11/2009 csi instalaciones.
Page 16
Page 16 of 22 10/11/2009 csi instalaciones.
Page 17
Page 17 of 22 10/11/2009 water power(kw) duration capacit consumptio net mode inlet resistor max min. Of rinse weigh pressure voltage power supply. Dru tub absorb basket (mm) cycle tub(l) water(l) (kg) ad-15 2÷4 kg/cm2 (28÷56psi) ad- 15d 3.5÷5 kg/cm2 (42÷70psi) 2.4 2.66 350x35 0 11 2 36 ad-21 2÷4 kg...
Page 18
Page 18 of 22 10/11/2009 water power(kw) basket, capacit consumptio net model inlet resistor max square of rinse weigh pressure drainage hose power supply voltage dru tub absorb (mm) cycle duration tub(l) water(l) (kg) ad - 64 6.65 60 ad - 64b ad - 64b-bt ad – 64hy clinic ad – 64c (200÷400 kpa) (2÷4...
Page 19
Page 19 of 22 10/11/2009 notes csi instalaciones.
Page 20
Page 20 of 22 10/11/2009 notes notes csi instalaciones.
Page 21
Page 21 of 22 10/11/2009 notes csi instalaciones.
Page 22
Page 22 of 22 10/11/2009 csi instalaciones.