Owner’s manual read and save these instructions model no. Fp2500** the treventi ® ceiling fan average weight 30-35 lbs. (depending on housing, blades & accessory choices) standard & damp location models @ @ damp location model; top of fan is marked, “suitable for use in damp locations”.
. Table of contents unpacking instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 electrical and structural requirements . . . . . . . . . . . . . . . . . . . . ...
Rev u/l d/l fan off off on low med hi 3 this manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan unpacking instructions for your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that a...
4 electrical and structural requirements ceiling ceiling joists 2˝ x 4˝ outlet box figure 1 your new ceiling fan will require a grounded electrical supply line of 120 volts ac, 60 hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. Figu...
5 how to assemble your ceiling fan pin setscrew hanger ball figure 5 1. Prior to assembly, set aside and save the hardware bag(s) packed in the packing. 2. Remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod. (figure 5) remove the pin from...
6 how to assemble your ceiling fan (cont'd) the clevis pin must go through the holes in the downrod support and the holes in the downrod. Be sure to push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the...
Downrod/hanger ball assembly attach safety cable to ceiling support cable tab note: supply wires and fan wires omitted for clarity junction box ceiling support cable ceiling joist wood member (2˝ x 4˝ approx.) hanger bracket ceiling 7 how to hang your ceiling fan 2. Make sure the electrical supply w...
8 how to wire and operate your c22 remote control if you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. 9v battery remote transmitter unit detail receiver unit detail note: if fan or supply wires are different colors tha...
Fan motor unit bl-ac in l wh-ac in n blue-for light down blk-to motor l wh-to motor n grn or bare ground grn from hanger ball grn from bracket 120 v ac suppl y (user supplied) wh-for light down grn receiver unit grn blk blk yellow wire from motor - use only with lk25 light kit (see lk25 instructions...
10 installing the canopy housing 1. Screw in two threaded rods into the hanger bracket (figure 15a). Note: the threaded rods in the hanger bracket serves as guides for easier installation. 2. Securely attach the canopy housing to the hanger bracket using the external lockwashers and knurled knobs su...
11 mounting the cover switch housing maintenance blade cleaning periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint free cloth to avoid scratching the fi nish. Abrasive cleaning agents are not required and should be avoided t...
12 parts list ref. No. Description part # 1 hanger bracket assembly apg510bl 3 ceiling canopy pg160 ¾¾ hardware bag containing: hdwma25 ¾¾ 4 5/32˝ threaded rods (2) 5 5/32˝ external lockwashers (2) 6 knurled knobs (2) 10 phillips screwdriver & angled screwdriver 11 blade holder screws (10) 13 switch...
Rev u/l d/l fan off off on low med hi 13 note: the illustration shown is not to scale or its actual confi guration may vary. Wires partially removed for clarity. Exploded-view 18 19 9 8 11 12 10 17 7 6 4 5 3 14 2 1 ground wire (green) ground wire (green) the treventi ® fp2500** figure 18 7a 13 16 15...
14 trouble shooting ▲warning for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble probable cause suggested remedy 1. Fan will not start 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connection...
Copyright 2007 fanimation 2007/01 10983 bennett parkway zionsville, in 46077 (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 773-4113 visit our website @ www.Fanimation.Com.
