Native rate series native rate series plus digital video processor installation and operations manual ™.
Inventory list / unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 front pan...
Unpacking remove the nr series unit from the shipping con- tainer and examine it for any signs of shipping damage or missing items (check inventory list below). All shipping materials should be saved if the unit is to be moved or returned for service. Installation the processor can be either placed ...
Installation 3 connections because of the high performance of the nr series unit it is very important to use the highest quality cables possible, for both input and output signals. Both the rgb bnc and the d15 monitor output connections are active at all times and can run two displays simultaneously...
4 front panel control 1. Power/standby: press to turn the unit on (led turns green) or to standby (red) 2. Infrared sensor/flasher window 3. Cpu reset: push a small paper clip into this opening to reset the unit’s cpu. Note: do not activate the cpu reset without first contacting faroudja technical s...
Setup 5 • press the enter button, the preset leds turn red, the enter led turns green. (press enter again to cancel procedure) • press the preset you want to use and the led on that preset will turn green and the led on the enter will go out. Note: when functions are accessed via the front panel con...
It is recommended that sizing and blanking adjust- ments be done with the display device controls first to insure proper settings before using the fol- lowing commands. Bottom blanking right blanking left blanking top blanking image vertical position moves image up from center image horizontal posit...
Ir remote and osd operation there are four ways to control the unit: from the front panel, with the remote control buttons, using the on-screen-display with the remote and via rs232. Controlling from the front panel or the remote requires cycling through the available func- tions. If direct access i...
Use these commands to fine tune the image brightness contrast tint color detail noise reduction note: adjusting detail – the detail and noise reduction settings have been optimized for the scan rate and resolution of the nr series for most sources. However, the viewers tastes and the types of softwa...
Command function command function help display help menu system setup st report current status on power on e# echo 0=off, 1=on off power off w# screen shape, (0=wide, 1=4x3, 2=wide-4:3) cs# comp sync 0=off, 1=on inputs g# sync on green 0=off, 1=on v video input m# output mode (0-2) (0=rgb, 1=ycrcb, ...
Ir remote teaching functions use the function key to locate ir setup menu-press enter. Use the value key to select the different com- mands. Each time the enter button is pressed it “flashes” the commands out through the ir receiver win- dow on the front panel. Ir command 1 power on 2 power off 3 vi...
Inputs (interlaced) format ntsc/pal auto detect composite(bnc) 1vpp s-video y - 1v pp c -286mv pp component (smpte)(bnc) y—1vpp cr—700mv pp cb - 700mv pp rgb comp. Sync—1vpp rgb-700mv pp hd/pc pass-thru d15m remote control “d9f” rs-232 ascii outputs (progressive) r,g,b (bnc or db15) 700mv pp, ttl sy...
12 limited warranty faroudja laboratories, inc. (“faroudja”) warranties that its products will be free of defects in workmanship and material and conform substantially to published speci- fications under normal use and service. This warranty is made to the first purchaser of the products and extends...
