Fender 2230000000 Owner's Manual - ♫
7
7
fe nde r.co m
MORE
DRIVE
NORMAL
BRIGHT
2
1
ON
OFF
ON
STANDBY
CHANNEL
SELECT
PRESENCE
REVERB
MASTER
MIDDLE
BASS
TREBLE
DRIVE
VOLUME
INPUTS
POWER
AMP IN
PREAMP
OUT
FOOT
SWITCH
1
12
2
11
3
10
4
9
5
8
6 7
1
12
2
11
3
10
4
9
5
8
6 7
1
12
2
11
3
10
4
9
5
8
6 7
1
12
2
11
3
10
4
9
5
8
6 7
1
12
2
11
3
10
4
9
5
8
6 7
1
12
2
11
3
10
4
9
5
8
6 7
1
12
2
11
3
10
4
9
5
8
6 7
1
12
2
11
3
10
4
9
5
8
6 7
Hot Rod DeVille™/Deluxe™ III
Hot Rod DeVille™/Deluxe™ III
A. INPUT
1
— A normal sensitivity input, ideal for use with
most guitars.
♫
Either input jack can be used with any type of guitar
depending on the tone character you prefer. Experiment
and use the input that sounds the best to you.
B. INPUT
2
— A lower sensitivity input (–6dB) that provides
cleaner response with high-output and pre-amplified guitars.
♫
You can use Input 1 and Input 2 simultaneously with two
guitars or a guitar and a microphone, for example. Input
sensitivities become equal when used simultaneously.
C. NORMAL / BRIGHT
—
Press IN to boost the high-
frequency tones of the Normal channel.
Normal
Bright
D. VOLUME
— Adjusts the volume of the Normal channel.
E. MORE
DRIVE
— Press IN to boost the gain and distortion
of the Drive channel.
Drive
More Drive
F. DRIVE
— Increase the Drive setting to produce more
distortion and sustain. Use lower Drive settings to
produce cleaner sounds.
G. CHANNEL
INDICATOR
—
Off
J
J
Normal channel
Yellow
ÑJ
J
ÒDrive channel
Red
ÑJ
J
ÒMore Drive channel
H. TREBLE
— Adjusts high-frequency tone.
I. BASS
— Adjusts low-frequency tone.
J. MIDDLE
— Adjusts mid-frequency tone.
K. CHANNEL
SELECT
—
Normal channel
Drive channel
L. MASTER
— Use to adjust the loudness of the Drive and
More Drive channels in conjunction with DRIVE {F}.
M. REVERB
— Adjusts the level of the Reverb effect.
N. PRESENCE
— Adjusts tone at a point in the signal path
after the distortion circuitry to provide unique ultra high-
frequency tone shaping.
O. PREAMP OUT / POWER AMP IN — Multi-functional
input/output jacks that can be used in a variety of
configurations:
(1)
Effects Loop—Connect PREAMP OUT to the input of
your effects device and connect the effects output
to the POWER AMP IN jack.
(2)
Multiple Hot Rod Amps—Connect PREAMP OUT on
the primary unit to POWER AMP IN on the auxiliary
unit. The primary unit is used to control all auxiliary
units, except for REVERB and PRESENCE which remain
active on each auxiliary unit.
(3)
Recording or Sound Reinforcement—Connect
PREAMP OUT to the input jack of sound equipment.
♫
Use instrument (shielded) cables with TS (Tip-Sleeve)
plugs
for connections. Both PREAMP OUT and
POWER AMP IN jacks are located before Reverb and
Presence in the signal path.
P. FOOTSWITCH
— Connect the included footswitch here
to enable remote selection of the Normal / Drive / More
Drive channels. The CHANNEL SELECT {K} button on
the control panel is disabled when the footswitch is
connected.
♫
Speaker cable (unshielded) is superior to instrument
cable (shielded) for connecting the footswitch.
Q. POWER INDICATOR
— Illuminates when the unit is ON.
Unscrew the red jewel to access the bulb (type T47) for
replacement.
R. STANDBY
— Use Standby instead of switching the power
off during short breaks to avoid having to wait for the
tubes to warm up when you want to start playing again.
Also, keep the amplifier on Standby for the first 30
seconds when you first switch the power on to give the
tubes a gentle warm up cycle.
♫
Using Standby will extend the life span of your
amplifier's vacuum tubes by reducing the shock of the
heat-up / cool-down cycle on the tube filaments.
S. POWER
SWITCH
— Switches the unit ON/OFF.