- DL manuals
- Fervi
- Grinder
- 413
- Operation And Maintenance Manual
Fervi 413 Operation And Maintenance Manual
Summary of 413
Page 1
Operation and maintenance manual mini air die grinder art. 0413 translation of the original instructions fervi.Com.
Page 2: Preface
Hardware page 2 of 14 preface please ensure you have read this manual before any operation translation of the original instructions it is compulsory to read this instruction manual before starting operation. The guarantee that the machine will function and perform properly is strictly dependent upon...
Page 3: Contents
Hardware page 3 of 14 contents 1 general safety instructions............................................................. 4 1.1 risks associated with the work area ............................................................................4 1.2 risks associated with the presence of rotating and/or ...
Page 4: Parts
Hardware page 4 of 14 1 general safety instructions 1. During use, maintain control of the tool. The operators represent the most important aspect of safety. Working cautiously and carefully is the best protection against the risk of injury. 2. The pneumatic tool should not be used and repaired by s...
Page 5: 1.4 Technical Assistance
Hardware page 5 of 14 1.3 personal protective equipment when using the pneumatic tool, always wear the following: safety shoes; work gloves; hearing protection (cap, earplugs, etc.); protective goggles. 1.4 technical assistance for any problems and/or concerns, please contact, without hesitation, th...
Page 6: Use
Hardware page 6 of 14 2 description of the grinder and intended use the grinder is a portable pneumatic tool, to be used for grinding, finishing and chamfering of small surfaces. Replacing the abrasive tools (grinding wheels) it is possible to grind or polish different materials, such as metals, woo...
Page 7: 2.2 Pictograms
Hardware page 7 of 14 2.2 pictograms attached to each machine there is an obligation pictogram: carefully read the operation and maintenance manual before using the tool! Figure 2 – close-up of the pictograms 2.3 identification plate there is an identification plate on each machine, which shows the ...
Page 8
Hardware page 8 of 14 3 improper uses and precautions it is strictly forbidden !! to allow the tool to be used by untrained personnel and those who have not read the instruction manual; to use the tool for different purposes and uses other than those for which it was designed, i.E. Grinding, smo...
Page 9: 4 Commissioning
Hardware page 9 of 14 4 commissioning 1. Remove the air inlet cap, then screw the supplied nozzle into the hole: 1/4" npt male quick-release coupling 2. Put a few drops of lubricating oil (without resin acid) in the air inlet nozzle. 3. Check the flexible air supply hose. If it is damaged, broken, t...
Page 10: 5 How To Use
Hardware page 10 of 14 5 how to use 5.1 attaching the abrasive tools (wheels) crushing and cutting before attaching and/or removing the grinding wheels, always remove the air supply hose. Protective gloves before attaching and/or removing the grinding wheels, wear suitable protective gloves. 1. Choo...
Page 11: 5.2 Power On / Off
Hardware page 11 of 14 5.2 power on / off (personal protective equipment) ppe before using the grinder, wear suitable work clothing, gloves, shoes and protective goggles. Also wear a mask if you work with materials that produce dust or fumes. Also wear protective devices for the ears (hearing protec...
Page 12: Emergency
Hardware page 12 of 14 the grinder's start lever is a continuous hold lever, in the sense that the function controlled (i.E., the rotation of the grinding wheel) is active as long as the lever itself is kept pressed. Therefore, release the lever to shut it down in an emergency. Emergency in case of ...
Page 13
Hardware page 13 of 14 6 maintenance and cleaning the purpose of this chapter is to provide all the information on maintenance procedures and frequency that the grinder requires. Intervention frequency daily weekly 1. General visual inspection x 2. General cleaning x 3. Clean the air outlet nozzle x...
Page 14
Hardware page 14 of 14 7 bill of materials and spare parts ref. Description ref. Description 0413/01 body of the machine 0413/20 sealing gasket 0413/02 trigger 0413/21 bearing 0413/03 safety lock 0413/22 rear cylinder head 0413/04 spring 0413/23 straight pin 0413/05 straight pin 0413/24 blade 0413/0...