1. DL manuals
  2. Fiat
  3. Automobile
  4. 2015 500 Abarth
  5. Owner's Manual

Fiat 2015 500 Abarth Owner's Manual

Summary of 2015 500 Abarth

  • Page 1

    Fiat 500 abarth chrysler group llc o w n e r ’ s m a n u a l 2 0 1 5 2015 fia t 500 abar th 15fx24-126-aa first edition printed in u.S.A. I n c l u d e s c a b r i o.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc . Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents . Your driving ability...

  • Page 3

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the feat...

  • Page 5

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .5 䡵 warnings and cautions . . . . . . . . . . . . . .7 䡵 vehicle identification number . . . . . . . .7 䡵 vehicle modifications/alterations . . . .8 1.

  • Page 6

    Introduction congratulations on selecting your new vehicle. Be as- sured that it represents precision workmanship, distinc- tive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engineering spe...

  • Page 7

    How to use this manual consult the table of contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment. The detailed index ...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owners manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss importan...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped vin location 8 introduction.

  • Page 11

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .11 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .11 ▫ locking doors with a key. . . . . . . . . . . . . . . .13 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .13 䡵 sentry k...

  • Page 12

    䡵 liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 䡵 occupant restraints systems . . . . . . . . .24 ▫ important safety precautions . . . . . . . . . . . . . .24 ▫ seat belt systems . . . . . . . . . . . . . . . . . . . . . .26 ▫ supplemental restraint system (srs) . . . . . . . .3...

  • Page 13

    A word about your keys the key fob contains the remote keyless entry (rke) transmitter with an integrated key. To use the mechanical key simply press the mechanical key release button. The vehicle is supplied with a code card containing key code numbers to order duplicate keys, and the autho- rized ...

  • Page 14

    Warning! • before exiting a vehicle, always turn the ignition to the off/lock position, apply the parking brake, shift the transmission into reverse gear, and remove the key fob from the ignition. When leaving the vehicle, always lock your vehicle. • never leave children alone in a vehicle, or with ...

  • Page 15

    Warning! (continued) • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Caution! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unatt...

  • Page 16

    Note: a key which has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle. If the vehicle security light is on after the key is turned to the on/run position, it indicates that there is a problem with the electronics. Cau...

  • Page 17

    General information the sentry key® system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference that may be received, including interference ...

  • Page 18

    To unlock the doors and liftgate press and release the unlock button on the rke transmitter once to unlock the driver’s door or twice, within five seconds, to unlock all doors and the liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also...

  • Page 19

    3. Take out the battery case. Remove and replace the battery observing its polarity. 4. Refit the battery case inside the key fob and turn the screw to lock it into place. Key fob screw location battery case removed 2 things to know before starting your vehicle 17.

  • Page 20

    General information this device complies with part 15 of fcc rules and with rs-210 of industry canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may...

  • Page 21

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • for personal security and safety in the event of a collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • before ex...

  • Page 22

    Power door locks — if equipped a power door lock switch is incorporated into the driver door handle. Push or pull the handle to lock or unlock the doors and liftgate. If the driver’s door handle is pushed a red lock indicator will show on the driver’s door handle (indicating locked) when the door is...

  • Page 23

    Autoclose when enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). The auto door lock feature can be enabled or disabled using electronic vehicle information center (evic). To change the autoclose setting in the evic, proceed as follows: 1. Briefly pres...

  • Page 24

    Auto-down the driver’s door window switch has an auto-down fea- ture. Press the window switch for approximately one sec- ond, release, and the window will go down automatically. To cancel the auto-down movement, operate the switch in either the up or down direction and release the switch. Wind buffe...

  • Page 25

    Warning! • driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • if you are required to drive with the liftgate open, make sure that all windows are c...

  • Page 26

    Occupant restraints systems some of the most important safety features in your vehicle are the restraint systems: • seat belt systems • supplemental restraint systems (srs) air bags • child restraints important safety precautions please pay close attention to the information in this section. It tell...

  • Page 27

    4. Children that are not big enough to wear the vehicle seat belt properly (refer to “child restraints”) should be secured in the rear seat in child restraints or belt-positioning booster seats. Older children who do not use child restraints or belt-positioning booster seats should ride properly buc...

  • Page 28

    Seat belt systems buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and could cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can redu...

  • Page 29

    The outboard front passenger seat beltalert® is not active when the outboard front passenger seat is unoc- cupied. Beltalert® may be triggered when an animal or heavy object is on the outboard front passenger seat or when the seat is folded flat (if equipped). It is recom- mended that pets be restra...

  • Page 30

    Warning! • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belt even though you have air bags. • in a collision, you and your p...

  • Page 31

    Warning! (continued) • a lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug. • a twisted seat belt may not pro...

  • Page 32

    Warning! (continued) • a frayed or torn seat belt could rip apart in a collision and leave you with no protection. Inspect the seat belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be re- placed immediately. Do not disassemble or modify the seat belt system. Sea...

  • Page 33

    4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug seat belt reduces the risk of sliding...

  • Page 34

    6. To release the seat belt, push the red button on the buckle. The seat belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the seat belt to retract fully. Lap/shoulder belt untwisting procedure use the following procedure to untwist...

  • Page 35

    Warning! (continued) • using a seat belt extender when not needed can increase the risk of serious injury or death in a collision. Only use the seat belt extender when the lap belt is not long enough and only use in the recommended seating positions. Remove and store the seat belt extender when not ...

  • Page 36

    Energy management feature this vehicle has a seat belt system with an energy management feature in the front seating positions that may help further reduce the risk of injury in the event of a collision. This seat belt system has a retractor assembly that is designed to release webbing in a controll...

  • Page 37

    Driver center passenger first row n/a n/a alr second row alr n/a alr • n/a — not applicable • alr — automatic locking retractor if the passenger seating position is equipped with an alr and is being used for normal usage: only pull the seat belt webbing out far enough to comfortably wrap around the ...

  • Page 38

    How to engage the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire seat belt is extracted. 3. Allow the seat belt to retract. As the seat belt retracts, you will hear a clicking sound. This indicates the seat bel...

  • Page 39

    Supplemental restraint system (srs) air bag system components your vehicle may be equipped with the following air bag system components: • occupant restraint controller (orc) • air bag warning light • steering wheel and column • instrument panel • knee impact bolsters • advanced front air bags • sup...

  • Page 40

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 41

    Advanced front air bag features the advanced front air bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the occupant restraint controller (orc), which may receive information from the front i...

  • Page 42

    Warning! (continued) • do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air ba...

  • Page 43

    Seat belts are necessary for your protection in all colli- sions, and also are needed to help keep you in position, away from an inflating air bag. When the orc detects a collision requiring the ad- vanced front air bags, it signals the inflator units. A large quantity of non-toxic gas is generated ...

  • Page 44

    Supplemental driver knee air bag this vehicle is equipped with a supplemental driver knee air bag mounted in the instrument panel below the steering column. The supplemental driver knee air bag provides en- hanced protection during a frontal impact by working together with the seat belts, pretension...

  • Page 45

    When the sab deploys, it opens the seam on the out- board side of the seatback’s trim cover. The inflating sab deploys through the seat seam into the space between the occupant and the door. The sab moves at a very high speed and with such a high force that it could injure you if you are not seated ...

  • Page 46

    The sabic deploys downward, covering the side win- dows. An inflating sabic pushes the outside edge of the headliner out of the way and covers the window. The sabics inflate with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the sa...

  • Page 47

    The sabics and sabs (“side air bags”) are designed to activate in certain side impacts. The occupant restraint controller (“orc”) determines whether the deployment of the side air bags in a particular impact event is appropriate, based on the severity and type of collision. The side impact sensors a...

  • Page 48

    Warning! • side air bags need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. • being too close to the side air bags during deploy- ment could cause you to be severely injured or killed. • relying on the side air bags alone could lead to more severe in...

  • Page 49

    • as the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the are...

  • Page 50

    Enhanced accident response system in the event of an impact, if the communication network remains intact, and the power remains intact, depending on the nature of the event, the orc will determine whether to have the enhanced accident response sys- tem perform the following functions: • cut off fuel...

  • Page 51

    Customer action customer will see 1. Turn ignition off. (turn signal switch must be placed in neutral state). 2. Turn ignition on. Left turn light is off. Right turn light blinks. 3. Turn right turn signal switch on. Right turn light is on solid. Left turn light blinks. 4. Turn left turn signal swit...

  • Page 52

    Air bag warning light the air bags must be ready to inflate for your protection in a collision. The air bag warning light monitors the internal circuits and inter- connecting wiring associated with air bag sys- tem electrical components. The orc monitors the readiness of the elec- tronic parts of th...

  • Page 53

    While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately. • the air bag warning light does not come on during the four to eight seconds when the ignition switch is first turned to the on/run position...

  • Page 54

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 55

    Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The main purpose of an edr is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per-...

  • Page 56

    Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the united states, and every canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be pros- ecuted for ignoring it. Ch...

  • Page 57

    Note: • for additional information, refer to www.Seatcheck.Org or call 1–866–seatcheck. Canadian residents should refer to transport canada’s website for additional information: • http://www.Tc.Gc.Ca/eng/roadsafety/safedrivers- childsafety-index-53.Htm summary of recommendations for restraining chil...

  • Page 58

    Child size, height, weight or age recommended type of child restraint small children children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint forward-facing child restraint with a five-point harness, facing forward in the rear seat...

  • Page 59

    Infants and child restraints safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and conv...

  • Page 60

    Remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward- facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat be...

  • Page 61

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 62

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 63

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 64

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 62 things to know before starting your vehicle.

  • Page 65

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and teth...

  • Page 66

    Can the rear-facing child restraint touch the back of the front passenger seat? Yes the child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint owner’s manual for more information. Can the head restraints be removed?...

  • Page 67

    Locating the latch anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower an...

  • Page 68

    To install a latch-compatible child restraint always follow the directions of the child restraint manu- facturer when installing your child restraint. Not all child restraint systems will be installed as described here. 1. If the selected seating position has a switchable auto- matic locking retract...

  • Page 69

    7. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. How to stow an unused alr seat belt when using the latch attaching system to install a child restraint, stow all alr sea...

  • Page 70

    Installing child restraints using the vehicle seat belt the seat belts in the passenger seating positions are equipped with a switchable automatic locking retractor (alr) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a l...

  • Page 71

    What is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward facing child restraint, ...

  • Page 72

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 73

    8. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test...

  • Page 74

    3. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. 4. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. Warning! • an incorrectly anchored tether strap could lead to increased head motion and possib...

  • Page 75

    Engine break-in recommendations a long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While crui...

  • Page 76

    Safety tips transporting passengers never transport passengers in the cargo area. Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a v...

  • Page 77

    Warning! (continued) • if it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. The best protection against carbon monoxide entry into the vehicle body is a properly maintained ...

  • Page 78

    Air bag warning light the light should come on and remain on for four to eight seconds as a bulb check when the ignition switch is first turned on. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked...

  • Page 79

    Warning! (continued) • never put floor mats or other floor coverings on top of already installed floor mats. Additional floor mats and other coverings will reduce the size of the pedal area and interfere with the pedals. • check mounting of mats on a regular basis. Always properly reinstall and secu...

  • Page 80

    Door latches check for positive closing, latching, and locking. Fluid leaks check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid (if equipped), or brake fluid leaks are suspected, t...

  • Page 81

    Understanding the features of your vehicle contents 䡵 power convertible top — if equipped . .82 ▫ lowering the power top. . . . . . . . . . . . . . . . .82 ▫ raising the power top . . . . . . . . . . . . . . . . . .82 ▫ power convertible top relearn procedure . . . . .84 ▫ wind stop . . . . . . . . ...

  • Page 82

    ▫ ez entry feature. . . . . . . . . . . . . . . . . . . . . . .99 ▫ memory feature . . . . . . . . . . . . . . . . . . . . . . .99 ▫ heated seats — if equipped . . . . . . . . . . . . .100 ▫ head restraints. . . . . . . . . . . . . . . . . . . . . . .101 䡵 to open and close the hood . . . . . . . . ...

  • Page 83

    ▫ to vary the speed setting . . . . . . . . . . . . . . .116 ▫ to accelerate for passing . . . . . . . . . . . . . . . .117 䡵 rear park assist — if equipped . . . . . . . .118 ▫ rear park assist sensors. . . . . . . . . . . . . . . . .118 ▫ rear park assist warning display . . . . . . . . . .119 ▫ r...

  • Page 84

    Power convertible top — if equipped on vehicles equipped with a power convertible top, the power convertible top switch is located on the overhead console. The switch contains two buttons. The passenger side button, is used to open the power top, and the driver side button, is used to close the powe...

  • Page 85

    Note: rail lubrication is recommended every 2000 cycles, or if scratching noises due to dust are present. Refer to “fluids, lubes, and genuine part” in “maintain- ing your vehicle” for information. Caution! Failure to follow these cautions may cause interior water damage, stains or mildew on the top...

  • Page 86

    Power convertible top relearn procedure if your power convertible top does not operate in the auto opening/closing mode (automatically opening/ closing to the one-quarter open and three-quarter open comfort stops), or if the trunk lid does not open - the following relearn procedure may be necessary....

  • Page 87

    Wind stop the wind stop installs in the backseat area of the vehicle. The wind stop will not interfere with power top opera- tion. Therefore, it can remain installed when the top is up. Mirrors inside day/night mirror the mirror can be adjusted up, down, left, and right for various drivers. The mirr...

  • Page 88

    Note: this feature is disabled when the vehicle is moving in reverse. Caution! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Power mirrors the power mirror controls are locat...

  • Page 89

    The power mirror controls consist of a mirror select switch and a four-way mirror control switch. To adjust a mirror, press the mirror select switch to either the l (left) or r (right) to select the mirror you need to adjust. Using the mirror control switch, press on any of the four arrows for the d...

  • Page 90

    Spotter mirror — if equipped some models are equipped with a driver’s side spotter mirror. The spotter mirror allows for a greater range of visibility on the driver’s side of the vehicle. Folding mirrors the exterior mirrors are hinged to allow the mirror to pivot forward or rearward to help avoid d...

  • Page 91

    Sun visors the driver and passenger sun visors are located on the headliner, near the front windshield. The sun visor can be rotated downward or up against the door glass. Both sun visors are equipped with courtesy mirrors. Blue&me™ hands-free communication blue&me™ hands-free communication overview...

  • Page 92

    Having to take your eyes off the road or remove your hands from the steering wheel. To use voice commands you are not required to train the voice recognition system to recognize your voice. This implies that the system is nearly equally performing with different persons, i.E.: the voice recognition ...

  • Page 93

    Steering wheel controls and the instrument panel multi- function display. Please refer to the fiat blue & me radio supplement for further information. To get started with blue&me™ hands-free kit with voice recognition, you have to simply pair your bluetooth® wireless technology enabled mobile phone ...

  • Page 94

    • to interact with blue&me™ you can use either the buttons on the steering wheel or voice commands. With voice recognition, you can perform system func- tions by speaking voice commands, also identified as “keywords”. When the system recognizes a keyword, it will respond with the appropriate action....

  • Page 95

    • conference call — you can call another contact while you are engaged in a phone conversation (with bluetooth® phones supporting this option). • call waiting — while engaged in a phone conversa- tion, you can receive notification of another incoming phone call, answer the other incoming phone call,...

  • Page 96

    Message reader functions are managed by the control buttons on the steering wheel or by the blue&me™ voice commands. The blue&me™ message reader enables the following operations: • to display an indicator on the instrument panel that indicates you have received a new sms text. It will display the se...

  • Page 97

    The media player enables the following operations: • digital audio playback — you can play all your digital audio files (.Mp3, .Wma, .Wav, .Aac) or play a customized playlist (.M3u or .Wpl format). • audio file selection by category — you can play all audio files of a certain category, e.G.: album, ...

  • Page 98

    Warning! (continued) • the use of any handheld device while driving is not recommended. Use voice-operated systems when possible. Follow all applicable laws that may affect the use of electronic devices while driving. • keep the owner’s manual in the car: when kept in the car, the owner’s manual wil...

  • Page 99

    Front seats forward/rearward adjustment the adjusting bar is located at the front of the seats, near the floor. While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once the desired position is reached. Then, using body pressure, move forward and rearw...

  • Page 100

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Seat height adjustment the driver’s seat height can be raised or lowered by using a le...

  • Page 101

    Ez entry feature the driver and front passenger seats have an ez entry feature for rear seat passengers. Pull upward on the release tether, located on the outboard side of the seat- back, dump the seatback forward, then slide the seat forward to allow access in and out of the rear seat. Lift the sea...

  • Page 102

    Memory function option 2 — seat back only memory: after using the ez entry function, the seat back may first be returned upright prior to going back to the last fore/aft (memory) position on the tracks. This results in the seat back memory being set only – the track will then be locked forward of it...

  • Page 103

    Warning! (continued) • do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface tempera- ture of the seat. Hea...

  • Page 104

    Rear head restraints to raise the head restraint, pull upward on the head re- straint. To lower the head restraint, press the push button, located at the base of the head restraint, and push down- ward on the head restraint. Refer to “occupant restraints” in “things to know before starting your vehi...

  • Page 105

    2. Rotate the safety catch under the front edge of the hood, near the center, and raise the hood. 3. Lift the hood prop rod that clips to the right side (left side when standing in front of the hood) of the engine compartment. Place the hood prop rod in the hole of hood hinge to secure the hood in t...

  • Page 106

    Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. Caution! To prevent possible damage, do not slam the ho...

  • Page 107

    Note: when the headlights are turned on, the daytime running lights will be deactivated. High beams with the low beams activated, push the multi- function lever towards the instrument panel to turn on the high beams. Pull the multifunction lever toward the steering wheel to turn off the high beams. ...

  • Page 108

    Daytime running lights — if equipped to activate the daytime running lights (drl), rotate the end of the multifunction lever to the o symbol. Note: the low beams and side/taillights will not be on with drl. If allowed by law in the country in which the vehicle was purchased the drl function can be t...

  • Page 109

    Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Follow me home/headlight delay when this feature is selected the driver can choose to have the headlights remain on for a preset...

  • Page 110

    Caution! Before getting out of the vehicle be sure that the switch is in the center position or that the lights are off to avoid draining the battery. Interior light timing (center position) there are four different modes of operation that can be activated in this position: • when one door is opened...

  • Page 111

    Front fog lights — if equipped the fog light switch is located on the center stack of the instrument panel, just below the radio. Press the switch once to turn the front fog lights on. Press the switch a second time to turn the front fog lights off. Windshield wipers and washers the windshield wiper...

  • Page 112

    Front windshield wiper operation there are five different modes of operation for the front windshield wipers. The windshield wiper lever can be raised or lowered to access these modes: windshield wiper off this is the normal position of the wiper lever. Intermittent wiper operation push the lever do...

  • Page 113

    Manual high speed/mist push the lever upward from the off position. The wipers will operate at high speed to clear off road mist or spray from a passing vehicle. This operation will continue until the lever is released. When the lever is released, the wipers will return to the off position and autom...

  • Page 114

    Rear windshield wiper rotate the end of the windshield wiper/washer lever upward to the first detent past the intermittent settings for intermittent wipe operation. With the front wind- shield wiper active, rotate the end of the windshield wiper/washer lever upward. The rear wiper will operate in th...

  • Page 115

    Rear windshield washer operation push the windshield wiper/washer lever toward the instrument panel to activate the rear washer. Push and hold the lever for more than a half second and the wipers will activate automatically for three cycles after the lever is released. Tilt steering column — if equi...

  • Page 116

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Electronic speed control ...

  • Page 117

    To activate push the on/off button. The cruise indicator light in the instrument cluster will illuminate. To turn the system off, push the on/off button a second time. The cruise indicator light will turn off. The system should be turned off when not in use. Warning! Leaving the electronic speed con...

  • Page 118

    To resume speed to resume a previously set speed, push the res (+) button and release. Resume can be used at any speed above 25 mph (40 km/h). To vary the speed setting to increase speed when the electronic speed control is set, you can in- crease speed by pushing the res (+) button. The speed incre...

  • Page 119

    The speed decrement shown is dependant on the speed of u.S. (mph) or metric (km/h) units: u.S. Speed (mph) • pressing the set (-) button once will result in a 1 mph decrease in set speed. Each subsequent tap of the button results in a decrease of 1 mph. • if the button is continually pressed, the se...

  • Page 120

    Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use electronic speed control in heavy traffic or on roads that are winding, icy, snow-cov...

  • Page 121

    Rear park assist warning display the rear park assist warning screen is located within the electronic vehicle information center (evic). It provides audible and visual warnings to indicate the distance between the rear fascia/bumper and the detected obstacle. Refer to ⬙electronic vehicle information...

  • Page 122

    Audible and visual signals supplied by the rear park assist system signal meaning indication obstacle distance an obstacle is present within the sensors’ field of view audible signal (dashboard loudspeaker) • sound pulses emitted at a rate that increases as the distance decreases. • emits continuous...

  • Page 123

    While audible signals are emitted, the audio system is not muted. The audible signal is turned off immediately if the distance increases. The tone cycle remains constant if the distance measured by the inner sensors is constant. If this condition occurs for the external sensors, the signal is turned...

  • Page 124

    Park assist system usage precautions note: • ensure that the outer surface and the underside of the rear bumper is clean and clear of snow, ice, mud, dirt or other obstruction to keep the rear park assist system operating properly. • jackhammers, large trucks, and other vibrations could affect the p...

  • Page 125

    Caution! (continued) • the vehicle must be driven slowly when using rear park assist in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using rear park assist. Warning! • drivers must be careful when backing up even wh...

  • Page 126

    Power sunroof — if equipped the power sunroof roof switch is located in the overhead console. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location acces- sible to children. Occupants, particularly ...

  • Page 127

    To open press and hold the power sunroof switch rearward for approximately one second and the sunroof will stop at the vented position. Press the switch a second time and hold for approximately one second and release, the sunroof will open fully, then stop automatically. This is called “express open...

  • Page 128

    Emergency operation in case of electrical failure the sunroof can be operated with the hex wrench that is located in the glove box. There is a plug located in the rear of the sunroof opening at the center of the vehicle. Removing the plug reveals a hex opening in the motor assembly of the sunroof. I...

  • Page 129

    Power is available when the ignition switch is in the on/run or start position. Insert the cigar lighter or accessory plug into the outlet for use. To preserve the heating element, do not hold the lighter in the heating position. Caution! • do not exceed the maximum power of 160 watts (13 amps) at 1...

  • Page 130

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 131

    Caution! (continued) • accessories that draw higher power (i.E., coolers, vacuum cleaners, lights, etc.) will degrade the bat- tery even more quickly. Only use these intermit- tently and with great caution. • after the use of high power draw accessories, or long periods of the vehicle not being star...

  • Page 132

    For rear passengers, there are cupholders located on the floor between the front driver and passenger seats. Storage glove compartment the glove compartment is located on the right side of the instrument panel. Pull outward on the glove compartment latch to open the glove compartment. Push the glove...

  • Page 133

    Cargo area features the rear seatbacks have a fold down feature to allow increased cargo capacity. Push down the release button, located at the outboard top of the seatback and move the seatback to its folded- down position to provide a flat load floor cargo area. When returning the seatback to its ...

  • Page 134

    Rear window features rear window defroster the rear window defroster button is located in the center of the instrument panel, below the radio. Press this button to turn on the rear window defroster. An indicator in the instrument cluster will illuminate when the rear window defroster is on. The rear...

  • Page 135

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 137

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .137 䡵 turbo boost gauge . . . . . . . . . . . . . . . . . .138 䡵 instrument cluster . . . . . . . . . . . . . . . . .139 䡵 instrument cluster descriptions . . . . .140 䡵 electronic vehicle information center ...

  • Page 138

    ▫ technical specifications . . . . . . . . . . . . . . . . .173 ▫ quick guide . . . . . . . . . . . . . . . . . . . . . . . . .174 ▫ general information. . . . . . . . . . . . . . . . . . . .177 ▫ functions and adjustments . . . . . . . . . . . . . .178 ▫ radio . . . . . . . . . . . . . . . . . . . ...

  • Page 139

    Instrument panel features 1 — side vent 7 — passenger air bag 13 — storage compartment 2 — multifunction lever – light control 8 — glove compartment 14 — shift lever 3 — instrument cluster and warning lights 9 — rear defrost button 15 — sport button 4 — windshield wiper, washer, trip computer 10 — h...

  • Page 140

    Turbo boost gauge your vehicle is equipped with a boost gauge and inte- grated shift light indicator located to the left of the instrument cluster. The boost gauge indicates the intake manifold pressure relative to barometric pressure. The engine management system in your vehicle intelligently regul...

  • Page 141

    Instrument cluster 4 understanding your instrument panel 139.

  • Page 142

    Instrument cluster descriptions 1. Tire pressure monitoring telltale light — if equipped each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure ...

  • Page 143

    When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. Tpms malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the tpms from functi...

  • Page 144

    Note: • a continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on. • check for an inoperative outside light bulb if either indicator remains on and does not flash, or flashes at a rapid rate. 4. Electronic stability control (esc) activation/ malfunct...

  • Page 145

    5. Air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to on/run. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible. Re...

  • Page 146

    9. Malfunction indicator light (mil) the malfunction indicator light (mil) is part of an onboard diagnostic (obdii) system which monitors the emissions and engine control sys- tem. If the vehicle is ready for emissions testing, the light will come on when the ignition is first turned on and remain o...

  • Page 147

    10. Front fog light indicator — if equipped this indicator will illuminate when the front fog lights are on. 11. Electric power steering malfunction warning light this telltale is on when the electric power steering is not operating and needs service. 12. Rear fog light indicator — if equipped this ...

  • Page 148

    14. Brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system...

  • Page 149

    Warning! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. Vehicles equipped with the abs, are also equipped with electronic brake force dist...

  • Page 150

    If the abs light is on, the brake system should be serviced as soon as possible to restore the benefits of anti-lock brakes. If the abs light does not turn on when the ignition switch is turned to the on/run position, have the light inspected by an authorized dealer. 16. Gas pedal percentage gauge/t...

  • Page 151

    Caution! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “h” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h” and you hear cont...

  • Page 152

    Electronic vehicle information center (evic) the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following: • system status • vehicle information warning message displays • personal settings (cus...

  • Page 153

    Evic displays 1. Red telltales (left bank) • hood ajar • low oil pressure • electronic throttle control • door ajar • speed limiter — if equipped 2. Amber telltales • ice risk • fuel cut off • fuel cut off failed • hill holder failed • oil change request • check lights • vehicle lock 3. Cruise contr...

  • Page 154

    5. Red telltales (right bank) • trunk ajar • transmission failure • battery charge indicator 6. Exceeded speed limiter 7. Shift up or down indicators 8. Gear indicator evic control buttons press the menu button briefly to access the evic. Press and hold the menu button (approximately one second) to ...

  • Page 155

    Electronic vehicle information center (evic) setup menu the menu comprises a series of functions arranged in a cycle. Press the up and down buttons to access the different options and settings (setup). The setup menu can be activated by pressing the menu button. Single presses on the up or down but-...

  • Page 156

    Selecting an option of the main menu without submenu 1. Briefly press the menu button to select the main menu option to set. 2. Press the up or down button (by single presses) to select the new setting. 3. Briefly press the menu button to store the new setting and go back to the main menu option pre...

  • Page 157

    Change engine oil indicator system change engine oil your vehicle is equipped with an engine oil change indicator system. The “change engine oil” message will flash in the evic display for approximately 10 seconds after a single chime has sounded to indicate the next scheduled oil change interval. T...

  • Page 158

    Trip button the trip button, located on the right steering column stalk, can be used to display and to reset the previously described values. • a short button press displays the different values. • a long button press resets the system and then starts a new trip. New trip to reset: • push and hold t...

  • Page 159

    Trip functions both trip functions are resettable (reset — start of new trip). “trip a” can be used to display the figures relating to: • range • trip distance a • average economy • instantaneous economy • average speed a • travel time a (driving time) “trip b” can be used to display the figures rel...

  • Page 160

    Note: the range depends on several factors: driving style, type of route (freeway, residential, mountain roads, etc.), conditions of use of the car (load, tire pressure, etc.). Trip planning must take into account the above notes. Distance traveled this value shows the distance covered since the las...

  • Page 161

    To adjust the brightness, proceed as follows: 1. Press the up or down button to set the required brightness level. 2. Briefly press the menu button to go back to the menu screen or press and hold the menu (approximately one second) to go back to the main screen without storing settings. Speed beep (...

  • Page 162

    • briefly press the menu button to go back to the menu screen, or press and hold the menu button (approxi- mately one second) to go back to the main screen without storing the settings. To cancel the setting, proceed as follows: 1. Briefly press the menu button. “on” will flash on the display. 2. Pr...

  • Page 163

    Set time (clock) this function may be used to set the clock through two submenu items: “time” and “mode.” proceed as follows: 1. Briefly press the menu button. Press the up or down buttons to highlight set time — press menu button. 2. Press the up or down button to navigate the two sub-menu items. 3...

  • Page 164

    When you have selected the required settings, briefly press the menu button to go back to the time, mode sub-menu screen, or press and hold the menu button (approximately one second) to go back to the main screen without storing the settings. Set date this function may be used to set the date (day -...

  • Page 165

    See radio (repeat audio information) with this function active, the evic display shows infor- mation relevant to the sound system. • radio: tuned radio station frequency, automatic tuning activation or autostore. • cd audio, cd mp3: track number. To activate (on) or to deactivate (off) the sound sys...

  • Page 166

    3. Briefly press the menu button to go back to the menu screen, or press and hold the menu button (approxi- mately one second) to go back to the main screen. Autoclose with this function active, the doors will automatically lock at when the vehicle’s speed exceeds 15 mph (24 km/h). To change the set...

  • Page 167

    6. Briefly press the menu button to return to the sub-menu. 7. When accessing the “fuel economy” submenu, briefly press the menu button. Either “mpg,” “km/l ” or “l/100km” will appear on the display (according to the previous setting). If the distance unit set is “mi,” the fuel economy unit will be ...

  • Page 168

    2. Press the up or down button for setting. 3. Briefly press the menu button to go back to the menu screen, or press and hold the menu button (approxi- mately one second) to go back to the main screen without storing the settings. Buzzer volume (adjusting the failure/warning buzzer volume) with this...

  • Page 169

    3. Briefly press the menu button to go back to the menu screen, or press and hold the menu button (approxi- mately one second) to go back to the main screen without storing the settings. Belt buzzer (buzzer activation for s.B.R. Indication) this function will only be displayed after a fiat group aut...

  • Page 170

    To set the required unit, proceed as follows: 1. Briefly press the menu button to display the two sub-menus. 2. Press the up or down button to navigate the two sub-menus. 3. Select the required sub-menu and then briefly press the menu button. 4. Press the up or down button for setting. 5. Briefly pr...

  • Page 171

    Tire pressure this function will be used to display the tire pressures individually for all four tires by location. Proceed as follows: 1. Briefly press the menu button. Press the up or down button to highlight the tire pressure. Press the menu button to enter the tire pressure menu . 2. Press the u...

  • Page 172

    Sales code (rab) radio introduction the radio has been designed according to the specifica- tions of the passenger compartment, with a personalized design to match the style of the dashboard. If the radio has blue&me™, refer to the appropriate “blue&me™ user’s manual” for further information. The in...

  • Page 173

    Reception conditions reception conditions change constantly while driving. Reception may be interfered with by the presence of mountains, buildings or bridges, or when you are far away from the broadcaster. Warning! Having the volume turned up high can cause the driver to not be able to hear importa...

  • Page 174

    • do not stick labels on the cd surface or write on the recorded surface with pencils or pens. • do not use cds that are very scratched, flawed, distorted, etc. Using discs like these will result in malfunctions or damage to the player. • the use of original cd media is required for the best quality...

  • Page 175

    Technical specifications the complete system consists of: • two 165 mm diameter midwoofer speakers, one speaker in each of the front doors. • two 22 mm diameter tweeter speakers, one speaker in each of the front pillars. • two 100 mm diameter full range speakers, one speaker in each of the rear side...

  • Page 176

    Quick guide radio controls button general functions mode on short button push off short button push tuner am, fm, sat (if equipped) source selection short repeated button push a-b-c cycles a, b, c presets for am, fm, sat (if equipped) short repeated button push media cd/aux/media player (if equipped...

  • Page 177

    Button general functions mode audio audio adjustments: low tones (bass), high tones (treble), left/ right balance (balance), front/ rear balance (fader) menu activation: short button push adjustment type selection: push or adjustment of values: push or (information button) song, artist, album, genre...

  • Page 178

    Button radio functions mode radio station search: • automatic search • manual search automatic search: push buttons or (long push for fast forward) manual search: push buttons or (long push for fast forward) 1 2 3 4 5 current radio station storing long button push for memory preset 1 to 5 respective...

  • Page 179

    General information the radio offers the following functions: radio section • pll tuning with fm/am bands • rbds (radio broadcast data system) • automatic/manual station tuning • fm multipath detector • manual storing of 25 stations (base radio) and 40 stations (if equipped with satellite): 15 on fm...

  • Page 180

    • track selection (forward/backward) • fast forward/rewind through tracks • mp3 display function: display of folder name, id3- tag information, time elapsed since the start of the track, name of the file • playing audio or data cd, cd-r and cd-rw audio section • mute/pause function • soft mute funct...

  • Page 181

    Selecting the cd function by briefly pushing the media button, the cd audio source can be selected (only if a cd is loaded). Volume adjustment to adjust the volume, push the buttons +vol or –vol to increase/decrease the volume. Mute/pause function push the button briefly to activate the mute func- t...

  • Page 182

    The current status of the selected function appears on the display. The functions managed by the audio menu are: • bass (bass adjustment) • midrange (midrange adjustment) • treble (treble adjustment) • balance (right/left balance adjustment) • fader (front/rear balance adjustment) • loudness — if eq...

  • Page 183

    3. Push the button to increase the sound from the left speakers or the button to increase the sound from the right speakers. By pushing the or buttons briefly, the levels will change progressively. By pushing them down longer, the levels will change quickly. Select the value “0” to set the right and...

  • Page 184

    Preset/user/classic/rock/jazz functions — if equipped the built-in equalizer can be activated/deactivated. When the equalizer function is off, the audio settings can only be changed by adjusting the “bass” and “treble” settings, whereas when the function is on, the acoustic curves can be adjusted. T...

  • Page 185

    Menu menu button functions push the menu button briefly to activate the menu function. Use the or buttons to scroll through the menu functions. To change the setting of the selected func- tion, use the or buttons. The current status of the selected function appears on the display. The functions mana...

  • Page 186

    On volume limit this function makes it possible to activate/deactivate the maximum volume limit when turning the radio on. The display shows the function status: • “on volume limit: on” – when the radio is turned on the volume level will be: – if the volume level is equal to or higher than the maxim...

  • Page 187

    Radio off function this function makes it possible to set the radio switching off mode by choosing between two methods. The chosen mode appears on the display: • “radio off: 00 min” — the radio turns off in connec- tion with the ignition key; the radio is turned auto- matically off as soon as the ke...

  • Page 188

    Once the radio mode has been activated, the display will show the name (rbds stations only) or the frequency of the selected radio station, the frequency band selected (e.G. Fma) and the preset button number (e.G. P1). Frequency band selection with the radio mode active, press the fm or am tuner but...

  • Page 189

    Automatic tuning briefly push the or button to start the automatic tuning search for the next station that can be received in the selected direction. If the or button is pushed for longer, the rapid search is started. When the button is released, the tuner will stop on the next station that can be r...

  • Page 190

    Siriusxm satellite radio with over 130 channels, siriusxm satellite radio brings you more of what you love. Get 69 channels of 100% commercial- free music, plus all of your favorite sports, news, talk and entertainment. Hear every nfl game, every nascar race, college sports and more. The biggest and...

  • Page 191

    Re-subscribe to siriusxm satellite radio new vehicle purchasers or lessees will receive a free limited time subscription to siriusxm satellite radio with their radio. Following expiration of the free services, it will be necessary to access the information on the subscription information screen in o...

  • Page 192

    Sirius subscription issues when replacing a sirius radio when a radio needs to be replaced, the dealer will need the sirius information to order a new radio (even if the sirius subscription has lapsed). The esn number con- tains 12 digits. The following are instructions for retrieving the elec- tron...

  • Page 193

    It is advisable to use original cds to ensure optimal playing. If cd-r/rws are used, we recommend using good quality media that are burned at the slowest speed possible. Cd loading/ejecting to load the cd, insert it gently into the slot to activate the motorized loading system, which will position i...

  • Page 194

    A cd which cannot be read will not be ejected until these functions are over. At the end, with the cd mode activated, the display will show the wording “cd disc error” for a few seconds and then the cd will be ejected. Display information when the cd player is operating, information will ap- pear on...

  • Page 195

    Cd mp3 player introduction this chapter describes the operation of the cd mp3 player. Note: layer-3 audio decoding technology is licensed from fraunhofer iis and thomson multimedia. Mp3 mode in addition to playing regular audio cds, the radio is also enabled to play cdroms on which compressed audio ...

  • Page 196

    Selecting mp3 sessions with hybrid discs if a hybrid disc is inserted (mixed mode, enhanced, cd-extra) also containing mp3 files, the radio automati- cally starts playing the audio session. It is possible to move to the mp3 session while playing by keeping the cd button pressed for more than two sec...

  • Page 197

    Structure of the folders the radio with mp3 player: • recognizes only the folders that effectively contain mp3 format files. • if the mp3 files on a cd-rom are structured in sub-folders their structure is compressed to a single level structure, where the sub-folders are taken to the level of the mai...

  • Page 198

    The duration of the mp3 tracks is not correctly displayed: in some cases (due to the recording mode) the duration of the mp3 tracks can be displayed incorrectly. Operating instructions — hands-free phone refer to the appropriate “blue&me™ user’s manual” for further information. Personal/portable nav...

  • Page 199

    Steering wheel audio controls the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pu...

  • Page 200

    Radio operation pushing the top of the switch will “seek” up for the next listenable station and pushing the bottom of the switch will “seek” down for the next listenable station. The button located in the center of the left-hand control will tune to the next preset station that you have pro- gramme...

  • Page 201

    5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. Note: if you experience difficulty in playing a particular disc, it may be damaged (e.G., scratched, reflective coat- ing removed, a hair, moist...

  • Page 202

    The manual climate controls consist of a series of rotary dials and one inner push knob. 1. Temperature control rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial to the left into the blue area of the scale indicates cooler temperatures, wh...

  • Page 203

    4. Mode control rotate this control to change the system between modes (panel, bi-level, floor, mix, defrost). • panel air is directed through the outlets in the instrument panel. These outlets can be ad- justed to direct airflow. Note: the center instrument panel outlets can be aimed so that they a...

  • Page 204

    5. A/c button push this button to engage the air conditioning. A light will illuminate when the air conditioning system is engaged. Max a/c for maximum cooling, use the a/c and recirculation modes at the same time. Economy mode if economy mode is desired, push the a/c button to turn off the indicato...

  • Page 205

    1. Auto temperature control (atc) button controls airflow, temperature, distribution, and air recir- culation automatically. Push and release to select. Per- forming this function will cause the atc to switch between manual mode and automatic modes. Refer to “automatic operation” for more informatio...

  • Page 206

    5. Mix mode air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. Performing this function wi...

  • Page 207

    9. Bi-level air is directed through the panel and floor outlets. Press and release the panel mode button and floor mode button to enter bi-level mode, the indicators illuminate when on. Performing this function will cause the atc to switch into manual mode. 10. Temperature control down button provid...

  • Page 208

    Note: • if the system is in mix or defrost mode, the a/c can be turned off, but the a/c system shall remain active to prevent fogging of the windows. • if fog or mist appears on the windshield or side glass, select defrost mode and adjust blower speed if needed. Recirculation control when outside ai...

  • Page 209

    Automatic operation 1. Push the auto button on the automatic temperature control (atc) panel, the indicator will illuminate when on. 2. Next, adjust the temperature you would like the system to maintain by adjusting the temperature con- trol buttons. Once the desired temperature is dis- played, the ...

  • Page 210

    Manual operation the system allows for manual selection of blower speed, air distribution mode, a/c status and recirculation con- trol. The blower fan speed can be set to any fixed speed by adjusting the blower control. The fan will now operate at a fixed speed until additional speeds are selected. ...

  • Page 211

    Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging. Note: automatic temperature controls...

  • Page 212

    Operating tips chart 210 understanding your instrument panel.

  • Page 213

    Window fogging windows will fog on the inside when the humidity inside the vehicle is high. This often occurs in mild or cool temperatures when it’s rainy or humid. In most cases, turning the air conditioning (pressing the a/c button) on will clear the fog. Adjust the temperature control, air direct...

  • Page 215

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .217 ▫ manual transmission — if equipped . . . . . . .217 ▫ automatic transmission — if equipped . . . . .217 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .217 ▫ cold weather operation . . . . . . . ....

  • Page 216

    ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . . .231 䡵 driving on slippery surfaces . . . . . . . . .233 ▫ acceleration . . . . . . . . . . . . . . . . . . . . . . . . .233 ▫ traction . . . . . . . . . . . . . . . . . . . . . . . . . . . .233 䡵 driving through water . . . . . . . . ....

  • Page 217

    䡵 tires — general information . . . . . . . .263 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . . .263 ▫ tire inflation pressures . . . . . . . . . . . . . . . . .264 ▫ tire pressures for high speed operation . . . .266 ▫ radial ply tires . . . . . . . . . . . . . . . . . . . . . .266 ▫...

  • Page 218

    ▫ materials added to fuel . . . . . . . . . . . . . . . .286 ▫ fuel system cautions. . . . . . . . . . . . . . . . . . .286 ▫ carbon monoxide warnings . . . . . . . . . . . . .287 䡵 adding fuel . . . . . . . . . . . . . . . . . . . . . . . .288 ▫ fuel filler cap (gas cap) . . . . . . . . . . . . . ....

  • Page 219

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a numb...

  • Page 220

    Turn the ignition switch to the avv/acc (start) position and release it when the engine starts. If the engine fails to start within 10 seconds, turn the ignition switch to the stop (off/lock) position, wait 10 to 15 seconds, then repeat the “normal starting” procedure. Cold weather operation to prev...

  • Page 221

    3. If the engine fails to start within ten seconds, cycle the ignition to the stop (off/lock) position, wait five seconds to allow the starter to cool, then repeat the extended park starting procedure. 4. If the engine fails to start after eight attempts, allow the starter to cool for at least 10 mi...

  • Page 222

    After starting the idle speed will automatically decrease as the engine warms up. Turbocharger “cool down” this vehicle is equipped with an after-run pump to cool the turbocharger after the engine is shut off. Depending on the type of driving and the amount of cargo, the pump will run for up to 10 m...

  • Page 223

    Fully press the clutch pedal before you shift gears. As you release the clutch pedal, lightly press the accelerator pedal. Use each gear in numerical order; do not skip a gear. Be sure the transmission is in first gear, not third, when starting from a standing position. Damage to the clutch can resu...

  • Page 224

    Recommended shift speeds to use your manual transmission for optimal fuel economy, it should be upshifted as listed in the following table. Manual transmission recommended shift speeds units in mph (km/h) engine size accel- era- tion rate 1 to 2 2 to 3 3 to 4 4 to 5 1.4l turbo accel 14 (23) 23 (37) ...

  • Page 225

    Automatic transmission — if equipped caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into or out of park or reverse only after the vehicle has come to a complete stop. • do not shift between park, reverse, neu- tral, or drive when the engine is ...

  • Page 226

    Warning! (continued) locked in park, securing the vehicle against un- wanted movement. • when leaving the vehicle, always remove the igni- tion key from the vehicle and lock the vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a ve...

  • Page 227

    Six-speed automatic transmission the transmission gear position display (located in the instrument cluster) indicates the transmission gear range. You must press the brake pedal to move the shift lever out of park (refer to “brake/transmission shift inter- lock system” in this section). To drive, mo...

  • Page 228

    The transmission shift lever has park, reverse, neu- tral, drive, and autostick® shift positions. Manual shifts can be made using the autostick® shift control (refer to “autostick®” in this section for further informa- tion). Toggling the shift lever forward (-) or rearward (+) while in the autostic...

  • Page 229

    When parking on a hill, apply the parking brake before shifting the transmission to park, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of park. As an added precau- tion, turn the front wheels toward the curb on a downhill grade and away f...

  • Page 230

    Warning! (continued) locked in park, securing the vehicle against un- wanted movement. • when leaving the vehicle, always remove the igni- tion key from the vehicle and lock the vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a ve...

  • Page 231

    • look at the transmission gear position display and verify that it indicates the park position. • with brake pedal released, verify that the shift lever will not move out of park. Reverse (r) this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a comp...

  • Page 232

    Drive (d) this range should be used for most city and highway driving. It provides the smoothest upshifts and down- shifts, and the best fuel economy. The transmission automatically upshifts through all forward gears. The drive position provides optimum driving characteris- tics under all normal ope...

  • Page 233

    In the event of a momentary problem, the transmission can be reset to regain all forward gears by performing the following steps: 1. Stop the vehicle. 2. Shift the transmission into park. 3. Turn the ignition switch to the off position. 4. Wait approximately 10 seconds. 5. Restart the engine. 6. Shi...

  • Page 234

    Note: in autostick® mode, the transmission will only shift up or down when the driver moves the shift lever rearward (+) or forward (-), except as described below. • the transmission will automatically upshift when nec- essary to prevent engine over-speed. • the transmission will automatically downs...

  • Page 235

    Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. Driving on slippery surfaces acceleration rapid acceleration on snow covered, wet, or other slip- pery surfaces ma...

  • Page 236

    To reduce this possibility, the following precautions should be observed: 1. Slow down during rainstorms or when the roads are slushy. 2. Slow down if the road has standing water or puddles. 3. Replace the tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Mai...

  • Page 237

    Warning! • driving through standing water limits your vehi- cle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • driving through standing water limits your vehi- cle’s braking capabilities, which increases stopping distances. Therefore, after driving throu...

  • Page 238

    Caution! (continued) • driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.E., engine oil, trans- mission, axle, etc.) for signs of contamination (i.E., fluid that is milky or foamy in appearance) after driving through stan...

  • Page 239

    If the steering icon is flashing, it indicates that the vehicle needs to be taken to an authorized dealer for service. It is likely the vehicle has lost power steering assistance. If the steering icon is displayed and the “power steer- ing system over temp” message is displayed on the evic screen, t...

  • Page 240

    Parking brake before leaving the vehicle, make sure that the parking brake is fully applied. Also, be certain to leave the manual transmission in reverse or first gear. The parking brake lever is located in the center console. To apply the parking brake, pull the lever up as firmly as possible. To r...

  • Page 241

    When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. Warning! • never leave children alone in a vehicle, or with access to ...

  • Page 242

    Caution! If the brake warning light remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. Sport mode manual transmission — if equipped in sport mode, the engine is more responsive to the throttle pedal...

  • Page 243

    Automatic transmission — if equipped the sport mode increases steering feedback to the driver with slight increase in effort and changes the transmis- sion shift schedules for more aggressive shifting. This driving mode is useful while driving on twisty roads where more steering precision is desired...

  • Page 244

    Brake system your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability, the remaining system will still func- tion. However, there will be some loss of overall braking effectiveness. You may notice increased pedal travel during applica...

  • Page 245

    The abs includes an amber abs warning light. When the light is illuminated, the abs is not functioning. The system reverts to standard non-anti-lock brakes. Turning the ignition off and on again may reset the abs if the fault detected was only momentary. Warning! • pumping the anti-lock brakes will ...

  • Page 246

    Brake assist system (bas) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce...

  • Page 247

    Traction control system (tcs) the traction control system (tcs) monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide en- hanced acceleration and stability. A feature of the...

  • Page 248

    Hsa activation criteria the following criteria must be met in order for hsa to activate: • vehicle must be stopped. • vehicle must be on a 2.5% (manual transmission) or 7% grade or greater (automatic transmission) grade hill. • gear selection matches vehicle uphill direction (i.E., vehicle in neutra...

  • Page 249

    Electronic stability control (esc) the electronic stability control (esc) system enhances directional control and stability of the vehicle under various driving conditions. Esc corrects for oversteering or understeering of the vehicle by applying the brake of the appropriate wheel to assist in count...

  • Page 250

    Note: the esc off switch is located left of the steering column (manual transmission only). Warning! The electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esc cannot pre...

  • Page 251

    Esc operating modes the esc system has three available operating modes. Full on this is the normal operating mode for esc. Whenever the vehicle is started, the esc system will be in on mode. This mode should be used for most driving situations. Esc should only be turned to partial off for specific r...

  • Page 252

    Full off this mode is intended for off-highway or off-road use only and should not be used on public roadways. In this mode, all tcs and esc stability features are turned off, except for the limited slip feature described in the tcs section. To enter the “full off” mode, depress and hold the esc off...

  • Page 253

    The esc activation/malfunction indicator light also flashes when tcs is active. If the esc activation/ malfunction indicator light begins to flash during accel- eration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing roa...

  • Page 254

    Note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design standards. Tires designed to this standard ...

  • Page 255

    Tire sizing chart example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on u.S. Design standards, or ⴖ....Blank....ⴖ = passenger car tire based on european design standards, or lt = light truck tire based o...

  • Page 256

    Example: service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – the maximum speed corres...

  • Page 257

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 258

    Example: dot ma l9 abcd 0301 01 = number representing the year in which the tire was manufactured (two digits) – 01 means the year 2001 – prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured. Example: 031 could represen...

  • Page 259

    Term definition maximum inflation pressure the maximum inflation pressure is the maximum permissible cold tire inflation pressure for this tire. The maximum inflation pressure is molded into the sidewall. Recommended cold tire inflation pressure vehicle manufacturer’s recommended cold tire inflation...

  • Page 260

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Tire placard location (door) tire placard location (b-pillar) 258 starting and operating.

  • Page 261

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 262

    To determine the maximum loading conditions of your vehicle, locate the statement “the combined weight of occupants and cargo should never exceed xxx lbs or xxx kg” on the tire and loading information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) ...

  • Page 263

    Note: • if your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. The follow- ing table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and num- ber and size of occupan...

  • Page 264

    262 starting and operating.

  • Page 265

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 266

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the v...

  • Page 267

    Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always cold tire inflation pressure. Cold tire inflat...

  • Page 268

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure ...

  • Page 269

    Consult an authorized tire dealer for tire repairs and additional information. Damaged run flat tires, or run flat tires that have experienced a loss of pressure should be replaced imme- diately with another run flat tire of identical size and service description (load index and speed symbol). All s...

  • Page 270

    While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states pro- hibit studded tires; therefore, local laws should be checked before using these tire types. Summer or three season tires — if equipped su...

  • Page 271

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continu- ously when you are stuck, and do...

  • Page 272

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16” (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further infor- mation. Life of tir...

  • Page 273

    Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressures. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance when ...

  • Page 274

    Warning! (continued) • never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have a collision. • failure to equip your vehicle wi...

  • Page 275

    These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires. Rotation will increase tread life, help to maintain mud, snow and wet traction levels, and contribute to a smooth, quiet ...

  • Page 276

    Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold tire pressure. The tire pressure will vary with temperature by about 1 psi (7 kpa) for every 12° f (6.5° c). This means that when the out...

  • Page 277

    For example, your vehicle may have a recommended cold (parked for more than three hours) tire pressure of 30 psi (207 kpa). If the ambient temperature is 68° f (20° c) and the measured tire pressure is 27 psi (186 kpa), a temperature drop to 20° f (-7° c) will decrease the tire pressure to approxima...

  • Page 278

    Note: • the tpms is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • the tpms should not be used as a tire pressure gauge while adjusting your tire pressure. • driving on a significantly under-inflated tire causes the tire to overheat ...

  • Page 279

    The tpms consists of the following components: • receiver module. • four tire pressure monitoring sensors. • tire pressure monitoring telltale light. Tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illuminate in the instrument cluster, an audible chime...

  • Page 280

    5. Using wheels/tires not equipped with tpm sensors. Note: your vehicle may be equipped with a compact spare wheel and tire assembly. 1. The compact spare tire does not have a tire pressure monitoring sensor. Therefore, the tpms will not moni- tor the tire pressure in the compact spare tire. 2. If y...

  • Page 281

    Enhanced tpm system when the vehicle is equipped with an enhanced tpm system, the driver can view text messages showing the actual tire pressure value by position by selecting the tire pressure menu command in the instrument cluster. Refer to ”instrument panel features” in “understanding your instru...

  • Page 282

    Should this occur, you should stop as soon as possible and inflate the tires with low pressure to the vehicle’s recom- mended cold placard pressure value. Once the system receives the updated tire pressures, the system will auto- matically update and the “tire pressure monitoring telltale light” wil...

  • Page 283

    If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “tire pressure monitoring telltale light” will no longer flash, and the “service tire pressure monitoring system” message will no longer display, and a pres...

  • Page 284

    Shown. This indicates that the pressure values are still being received from the tpm sensors but they may not be located in the correct vehicle position. The system still needs to be serviced as long as the ⬙service tire pressure monitoring system ⬙ message is displayed. Note: • the tpms will not mo...

  • Page 285

    Of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this information. General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following...

  • Page 286

    Reformulated gasoline many areas of the country require the use of cleaner burning gasoline referred to as “reformulated gasoline.” reformulated gasoline contain oxygenates and are spe- cifically blended to reduce vehicle emissions and im- prove air quality. The manufacturer supports the use of refo...

  • Page 287

    If a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all of these symptoms: • operate in a lean mode. • obd ii “malfunction indicator light” on. • poor engine performance. • poor cold start and cold drivability. • increased risk for fuel system component corrosio...

  • Page 288

    Materials added to fuel all gasoline sold in the united states is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefore, you should not have to add anything to the f...

  • Page 289

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 290

    Adding fuel fuel filler cap (gas cap) the gas cap is located on the passenger side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle. Caution! • damage to the fuel system or emission control system could result from using an improper f...

  • Page 291

    Warning! (continued) • never add fuel when the engine is running. It may cause the mil to turn on and could cause a fire. • a fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. Not...

  • Page 292

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmission automatic transmission flat tow none transmission in neutral not allowed dolly tow front ok ok rear not allowed not allowed on trailer all ok ok this veh...

  • Page 293

    Caution! Towing this vehicle in violation of the above require- ments can cause severe transmission damage. Dam- age from improper towing is not covered under the new vehicle limited warranty. 5 starting and operating 291.

  • Page 295

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .295 䡵 if your engine overheats . . . . . . . . . . . .295 䡵 tirefit kit — if equipped . . . . . . . . . . . . .296 ▫ tirefit storage . . . . . . . . . . . . . . . . . . . . . .297 ▫ tirefit kit components and operation...

  • Page 296

    䡵 shift lever override . . . . . . . . . . . . . . . .321 䡵 towing a disabled vehicle . . . . . . . . . . .322 ▫ automatic transmission . . . . . . . . . . . . . . . . .323 ▫ manual transmission . . . . . . . . . . . . . . . . . . .324 294 what to do in emergencies.

  • Page 297

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the radio. Press the switch to turn on the hazard warning flashers. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Press th...

  • Page 298

    Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the n...

  • Page 299

    Tirefit storage the tirefit kit is located under the front driver’s seat. Tirefit kit components and operation tirefit kit location tirefit components 1 — sealant bottle 5 — mode select knob 2 — deflation button 6 — sealant hose (clear) 3 — pressure gauge 7 — air pump hose (black) 4 — power button 8...

  • Page 300

    Using the mode select knob and hoses your tirefit kit is equipped with the following symbols to indicate the air or sealant mode. Selecting air mode push in the mode select knob (5) and turn to this position for air pump operation only. Use the black air pump hose (7) when selecting this mode. Selec...

  • Page 301

    • the sealant bottle (1) and sealant hose (6) are a one tire application use and need to be replaced after each use. Always replace these components immediately at your original equipment vehicle dealer. • when the tirefit sealant is in a liquid form, clean water, and a damp cloth will remove the ma...

  • Page 302

    Warning! • do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the tirefit kit. • do not use tirefit or drive the vehicle under the following circumstances: – if the puncture in the tire tread is approx...

  • Page 303

    Warning! (continued) • tirefit sealant solution contains latex. In case of an allergic reaction or rash, consult a physician immediately. Keep tirefit out of reach of children. If swallowed, rinse mouth immediately with plenty of water and drink plenty of water. Do not induce vomiting! Consult a phy...

  • Page 304

    5. Uncoil the power plug (8) and insert the plug into the vehicle’s 12 volt power outlet. Note: do not remove foreign objects (e.G., screws or nails) from the tire. (c) injecting tirefit sealant into the deflated tire: • always start the engine before turning on the tire- fit kit. Note: manual trans...

  • Page 305

    Note: if the mode select knob (5) is on air mode and the pump is operating, air will dispense from the air pump hose (7) only, not the sealant hose (6). If the sealant (white fluid) does flow through the sealant hose (6): 1. Continue to operate the pump until sealant is no longer flowing through hos...

  • Page 306

    Caution! • the metal end fitting from power plug (8) may get hot after use, so it should be handled carefully. • failure to reinstall the cap on the fitting at the end of the sealant hose (6) can result in sealant con- tacting your skin, clothing, and the vehicle’s inte- rior. It can also result in ...

  • Page 307

    3. Uncoil the air pump hose (7) (black in color) and screw the fitting at the end of hose (7) onto the valve stem. 4. Check the pressure in the tire by reading the pressure gauge (3). If tire pressure is less than 19 psi (1.3 bar): the tire is too badly damaged. Do not attempt to drive the vehicle f...

  • Page 308

    (f) sealant bottle and hose replacement: 1. Uncoil the sealant hose (6) (clear in color). 2. Locate the round sealant bottle release button in the recessed area under the sealant bottle. 3. Press the sealant bottle release button. The sealant bottle (1) will pop up. Remove the bottle and dispose of ...

  • Page 309

    Torque specifications lug nut/bolt torque **lug nut/ bolt size lug nut/ bolt socket size 66 ft-lbs (90 n·m) steel wheels only 75 ft-lbs (100 n·m) aluminum wheels only m12 x 1.25 17 mm **use only chrysler recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. Inspect the wh...

  • Page 310

    Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten...

  • Page 311

    Warning! (continued) • being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be ra...

  • Page 312

    Preparations for jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the whe...

  • Page 313

    Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • turn on the hazard warning flashers. • block the...

  • Page 314

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Remove the scissors jack and tool bag from under the driver’s seat. 2. Remove center cap (if equipped). Note: before using the swivel wrench to remove the ...

  • Page 315

    3. Loosen, but do not remove, the wheel bolts by turning them to the left one turn while the wheel is still on the ground. Note: there are front and rear jacking locations on each side of the body (as indicated by the triangular lift point symbol on the sill molding). Do not raise the vehicle until ...

  • Page 316

    4. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed. Warning! Raising the vehicle higher than necessary ...

  • Page 317

    Warning! To avoid the risk of forcing the vehicle off the jack, do not fully tighten the wheel bolts until the vehicle has been lowered. Failure to follow this warning may result in personal injury. 7. Install the wheel and wheel bolts with the cone shaped end of the bolts toward the wheel. Lightly ...

  • Page 318

    Note: when using a portable battery booster pack, follow the manufacturer’s operating instructions and precautions. Warning! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Caution! Do not use a portable battery booster pack or any other ...

  • Page 319

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 320

    Jump-starting procedure warning! Failure to follow this jump-starting procedure could result in personal injury or property damage due to battery explosion. Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Con...

  • Page 321

    5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then turn the key to run position on the vehicle with the discharged battery. 6. Once the vehicle is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. D...

  • Page 322

    Caution! Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the en- gine to idle with the transmission in neutral for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure d...

  • Page 323

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously w...

  • Page 324

    5. Insert a small screwdriver or similar tool into the access hole, and push and hold the override release lever in. 6. Move the shift lever to the neutral position. 7. The vehicle may then be started in neutral. 8. Reinstall the shift lever override access cover. Towing a disabled vehicle this sect...

  • Page 325

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members ...

  • Page 326

    Caution! • do not flat tow any vehicle equipped with an automatic transmission. Damage to the drivetrain will result. If these vehicles require towing, make sure all drive wheels are off the ground. • towing this vehicle in violation of the above re- quirements can cause severe transmission damage. ...

  • Page 327

    Maintaining your vehicle contents 䡵 engine compartment — 1.4l turbo . . . .327 䡵 onboard diagnostic system — obd ii . .328 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . .329 䡵 replacement parts . . . . . . . . . . . . . . . . . .330 䡵 dealer service . . . . . . . . . . . . ...

  • Page 328

    ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .357 䡵 fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .364 ▫ interior fuses . . . . . . . . . . . . . . . . . . . . . . . .365 ▫ underhood fuses. . . . . . . . . . . . . . . . . . . ....

  • Page 329

    Engine compartment — 1.4l turbo 1 — engine coolant reservoir 5 — battery 2 — engine oil dipstick 6 — engine oil fill 3 — brake fluid reservoir 7 — washer fluid reservoir 4 — front distribution unit (fuses) 7 maintaining your vehicle 327.

  • Page 330

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 331

    Emissions inspection and maintenance programs in some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states that require an inspection and mainte- nance (i/m), this check verifies the...

  • Page 332

    • the mil will not flash at all and will remain fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is ready and you can proceed to the i/m station. If your obd ii system is not ready, you should see your authorized dealer or repair fac...

  • Page 333

    Note: intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. Warning! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If...

  • Page 334

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, or air conditi...

  • Page 335

    Caution! Do not overfill the engine with oil. Overfilling the engine with oil will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This loss of oil pressure and increased oil temperature could damage your engine. Change engine oil the oil change indicat...

  • Page 336

    Materials added to engine oil do not add any supplemental materials, other than leak detection dyes, to the engine oil. Engine oil is an engi- neered product and its performance may be impaired by supplemental additives. Disposing of used engine oil and oil filters care should be taken in disposing ...

  • Page 337

    Warning! (continued) for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed. Failure to do so can result in serious personal injury. Engine air cleaner filter selection the quality o...

  • Page 338

    Warning! (continued) • the battery in this vehicle has a vent hose that should not be disconnected and should only be replaced with a battery of the same type (vented). Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and th...

  • Page 339

    Warning! (continued) • the air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced technician. Caution! Do not use chemical flushes...

  • Page 340

    Refrigerant recovery and recycling hfo 1234yf — if equipped hfo 1234yf air conditioning refrigerant is a hydro- fluorocarbon (hfc) that is endorsed by the environmen- tal protection agency and is an ozone-saving product with a low gwp (global warming potential). However, the manufacturer recommends ...

  • Page 341

    2. Pull the console closeout cover rearward to disengage the front retaining tab and remove the cover. 3. Remove the two 5.5 mm screws (1 and 2) that secure the particulate air filter cover to the hvac housing. Console closeout panel air filter cover screw locations 7 maintaining your vehicle 339.

  • Page 342

    4. Remove the a/c air filter by pulling it straight out of the housing. Take note of the air filter position indicators. 5. Install the a/c air filter with the air filter position indicators pointing in the same direction as removal. Caution! The a/c air filter is identified with an arrow to indicat...

  • Page 343

    Body lubrication locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, decklid, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease, such as mopar® spray white lube to assure quiet, easy...

  • Page 344

    Rear wiper blade removal/installation 1. Lift the pivot cap on the rear wiper arm upward, this will allow the rear wiper blade to be raised off of the liftgate glass. Note: the rear wiper arm cannot be raised fully up- ward unless the pivot cap is raised first. 2. Lift the rear wiper arm upward to r...

  • Page 345

    4. Install the wiper blade pivot pin into the wiper blade holder at the end of the wiper arm, and firmly press the wiper blade until it snaps into place. 5. Lower the wiper blade and snap the pivot cap into place. Adding washer fluid the windshield washer fluid reservoir is located in the engine com...

  • Page 346

    Warning! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine ...

  • Page 347

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine perfor- mance and cause serious damage to the engine. • damage to the catalytic converter can res...

  • Page 348

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires di...

  • Page 349

    Coolant checks check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh engine coolant (anti- freeze). Check...

  • Page 350

    Caution! (continued) hybrid organic additive technology (hoat) en- gine coolant (antifreeze) or any “globally compat- ible” coolant (antifreeze). If a non-oat engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and r...

  • Page 351

    • mix a minimum solution of 50% oat engine coolant that meets the requirements of chrysler material stan- dard ms-12106 and distilled water. Use higher concen- trations (not to exceed 70%) if temperatures below −34° f (−37° c) are anticipated. • use only high purity water such as distilled or deion-...

  • Page 352

    The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loo...

  • Page 353

    As long as the engine operating temperature is satisfac- tory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicl...

  • Page 354

    • make sure that the coolant expansion bottle overflow hoses are not kinked or obstructed. • keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • do not change the thermostat for summer or winter operation. If replacement i...

  • Page 355

    Fluid reservoir. Fluid level can be expected to fall as the brake pads wear. The brake fluid level should be checked when the pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Note: if your vehicle is equipped with a manual trans- mission , the brake fl...

  • Page 356

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 357

    Manual transmission — if equipped lubricant selection use only the manufacturers recommended transmission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Fluid level check check the fluid level by removing the fill plug. The fluid level ...

  • Page 358

    Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Refer to “fluids, lubricants, and genuine parts” in this section for fluid specifications. Special additives the manufacturer s...

  • Page 359

    Caution! If a transmission fluid leak occurs, visit your autho- rized dealer immediately. Severe transmission dam- age may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately. Fluid and filter changes under normal operating conditions, the fluid installed at the f...

  • Page 360

    What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road salt, dirt and moisture accumulation. • stone and gravel impact. • insects, tree sap and tar. • salt in the air near seacoast localities. ...

  • Page 361

    Special care • if you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • it is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open. • if you detect any stone chips or scratches...

  • Page 362

    Note: if your vehicle is equipped with dark vapor chrome wheels do not use wheel cleaners, abrasives or polishing compounds. They will permanently damage this finish and such damage is not covered by the new vehicle limited warranty. Use only mild soap and water with a soft cloth. Used on a regular ...

  • Page 363

    Interior care use mopar® total clean to clean fabric upholstery and carpeting. Use mopar® total clean to clean vinyl upholstery. Mopar® total clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small part...

  • Page 364

    To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Gl...

  • Page 365

    Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol con...

  • Page 366

    Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced a...

  • Page 367

    Warning! (continued) • if a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. Interior fuses the interior fuse panel is part of the body control module (bcm) and is l...

  • Page 368

    Cavity vehicle fuse number mini fuse description 3 f53 5 amp tan instrument panel node 4 f38 20 amp yellow central door locking 5 f36 10 amp red diagnostic socket, car radio, climate control system 6 f43 20 amp yellow bi-directional washer 7 f48 20 amp yellow passenger power window 8 f13 7.5 amp bro...

  • Page 369

    Underhood fuses the front distribution unit is located on the right side of the engine compartment, next to the battery. To access the fuses, press the release tabs and remove the cover. The id number of the electrical component correspond- ing to each fuse can be found on the back of the cover. Fro...

  • Page 370

    Cavity maxi fuse mini fuse description f01 60 amp blue body controller f02 20 amp yellow audio amplifier f03 20 amp yellow ignition switch f04 40 amp orange anti-lock brake pump f05 70 amp tan electric power steering f06 20 amp yellow radiator fan - single speed f06 30 amp green radiator fan - low s...

  • Page 371

    Cavity maxi fuse mini fuse description f16 7.5 amp brown transmission f17 25 amp white powertrain (multiair – if equipped) f17 15 amp blue powertrain f18 15 amp blue powertrain f18 5 amp tan powertrain (multiair – if equipped) f19 7.5 amp brown air conditioning f20 15 amp blue heated seats – if equi...

  • Page 372

    Cavity maxi fuse mini fuse description f85 30 amp green (ato) rear defroster f87 5 amp tan rear defroster f90 5 amp tan heated mirrors – if equipped vehicle storage if you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • disconnect t...

  • Page 373

    Exterior bulbs bulb number front low and high beam headlamp hir2ll front parking/daytime running lamps w21/5w front fog lamps h11ll front side marker lamps w3w front turn signal lamps wy21w side direction lamps wy5w rear turn signal lamps py21w rear side marker lamps w3w rear tail and stop lamps p21...

  • Page 374

    Headlamps low beam and high beam 1. Remove the plastic cap from the back of the headlamp housing. 2. Rotate the bulb counter-clockwise. 3. Remove the bulb and replace as needed. 4. Install the bulb and rotate clockwise to lock in place. 5. Reinstall the plastic cap. Front turn signal, parking and da...

  • Page 375

    6. Install the bulb into socket, and rotate bulb/socket clockwise into lamp locking it in place. 7. Reinstall the plastic cap. Front fog lamps to replace the front fog lights, see your authorized dealer. Front/rear side marker lamps 1. Remove portion of the wheel liner to allow hand access to side m...

  • Page 376

    3. Remove four screws and separate the backplate from the lamp housing. 4. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise. 5. Remove the backup lamp bulb by pulling straight out. 6. Replace lamps as required and reinstall lamp. Center high mounted ...

  • Page 377

    Fluid capacities u.S. Metric fuel (approximate) 10.5 gallons 40 liters engine oil with filter 1.4 liter turbo engine 4 quarts 3.8 liters cooling system 1.4 liter turbo engine (mopar® antifreeze/engine coolant 10 year/150,000 mile formula) 4.6 quarts 4.4 liters 1.4 liter turbo engine (mopar® antifree...

  • Page 378

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/ 150,000 mile formula oat (organic additive technology) meeting the requirements of chrysler material standard ms-12106. Engine oil we recomme...

  • Page 379

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 380

    Chassis component fluid, lubricant, or genuine part manual transmission – if equipped we recommend you use mopar® c635 ddct/mtx transmission fluid automatic transmission – if equipped use only mopar® aw-1 automatic transmission fluid or equivalent. Failure to use the correct fluid may affect the fun...

  • Page 381

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .380 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .382 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 382

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 383

    Once a month or before a long trip: • check engine oil level • check windshield washer fluid level • check the tire inflation pressures and look for unusual wear or damage • check the fluid levels of the coolant reservoir and brake master cylinder as needed • check function of all interior and exter...

  • Page 384

    Maintenance chart mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176...

  • Page 385

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 386

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 387

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . .387 ▫ prepare for the appointment. . . . . . . . . . . . .387 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .387 ▫ be reasonable with requests . . . . ....

  • Page 388

    䡵 department of transportation uniform tire quality grades . . . . . . . .392 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .393 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .393 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .393 386 if you need consumer...

  • Page 389

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 390

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 391

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 392

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You will be pleased with their sincere efforts to re...

  • Page 393

    Campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. To contact nhtsa, you may either call the auto safety hotline toll free at 1–888–327–4236 (tty: 1–800–424– 9153), or go to http://www.Safercar.Gov; or write to: admini- s...

  • Page 394

    Diagnostic procedure manuals diagnostic procedure manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and cor...

  • Page 395

    Treadwear the treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled condi- tions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100. The relat...

  • Page 396

    The grade c corresponds to a level of performance, which all passenger car tires must meet under the federal motor vehicle safety standard no. 109. Grades b and a represent higher levels of performance on the laboratory test wheel, than the minimum required by law. Warning! The temperature grade for...

  • Page 397

    Index 10

  • Page 398

    Adding engine coolant (antifreeze) . . . . . . . . . . . .348 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .288 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .343 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .286 airbag. . . . . . . . . ....

  • Page 399

    Adding fluid . . . . . . . . . . . . . . . . . . . . . . . . . .356 fluid and filter changes . . . . . . . . . . . . . . . . . .357 fluid change . . . . . . . . . . . . . . . . . . . . . . . . . .357 fluid level check . . . . . . . . . . . . . . . . . . . . . . .356 fluid type . . . . . . . . . . . ...

  • Page 400

    Chains, tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . .272 changing a flat tire . . . . . . . . . . . . . . . . . . . . . . .308 chart, tire sizing . . . . . . . . . . . . . . . . . . . . . . . . .253 check engine light (malfunction indicator light) . .144 checking your vehicle for sa...

  • Page 401

    Pressure cap . . . . . . . . . . . . . . . . . . . . . . . . . .349 selection of coolant (antifreeze) . . . . . . . . . . . . .347 corrosion protection . . . . . . . . . . . . . . . . . . . . . . .357 cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 customer assistance . . . ....

  • Page 402

    Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . .315 towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .322 emission control system maintenance . . . . . . . . . .329 engine air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .334 break-in recommendations ....

  • Page 403

    Fluid level checks automatic transmission . . . . . . . . . . . . . . . . . .356 fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .376 fluids, lubricants and genuine parts . . . . . . . . . . .376 fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 freeing...

  • Page 404

    Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 heated mirrors. . . . . . . . . . . . . . . . . . . . . . . . . . . .88 heated seats. . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .199 hill st...

  • Page 405

    Liftgate (sedan) . . . . . . . . . . . . . . . . . . . . . . . . . . .22 light bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 ant...

  • Page 406

    Lubricant selection . . . . . . . . . . . . . . . . . . . . . .355 master cylinder (brakes) . . . . . . . . . . . . . . . . . . . .352 media hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 automatic dimming...

  • Page 407

    Power door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86 outlet (auxiliary electrical outlet) . . . . . . . . . . .126 steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .236 sunroof . . . . . ....

  • Page 408

    Safety tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 schedule, maintenance . . . . . . . . . . . . . . . . . . . . .380 seat belt beltalert® . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 disengage the automatic locking mode . . . . . . .36 energy management featu...

  • Page 409

    Snow tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .267 spark plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .376 specifications oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .333 speed control (cruise control). . . . . . . . . . . . . . . .11...

  • Page 410

    Inflation pressures . . . . . . . . . . . . . . . . . . . . . . .264 jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .308 life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . .270 load capacity . . . . . . . . . . . . . . . . . . . . . . . . .258 pressure monitor sys...

  • Page 411

    Unleaded gasoline . . . . . . . . . . . . . . . . . . . . . . . .283 untwisting procedure, seat belt . . . . . . . . . . . . . . . .32 vehicle identification number (vin) . . . . . . . . . . . . .7 vehicle loading . . . . . . . . . . . . . . . . . . . . . . . . . .259 vehicle modifications/alteratio...

  • Page 412

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals . Mobile two-way radios and telephone equipment must be installed properly by trained personnel . The following must be obs...

  • Page 413

    Fiat 500 abarth chrysler group llc o w n e r ’ s m a n u a l 2 0 1 5 2015 fia t 500 abar th 15fx24-126-aa first edition printed in u.S.A. I n c l u d e s c a b r i o.