1. DL manuals
  2. Fiat
  3. Automobile
  4. 2015 500 Abarth
  5. Owner's Manual

Fiat 2015 500 Abarth Owner's Manual

Summary of 2015 500 Abarth

  • Page 1

    Chrysler group llc o w n e r ’ s m a n u a l 2 0 1 5 2015 fia t 500 15ff500-126-ab second edition rev 1 printed in u.S.A. Fiat 500

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the feat...

  • Page 5: Introduction

    Introduction contents ! Introduction . . . . . . . . . . . . . . . . . . . . . . . .4 ! How to use this manual . . . . . . . . . . . . . .5 ! Warnings and cautions . . . . . . . . . . . . . .7 ! Vehicle identification number . . . . . . . .7 ! Vehicle modifications/alterations . . . .8 1.

  • Page 6

    Introduction congratulations on selecting your new vehicle. Be as- sured that it represents precision workmanship, distinc- tive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engineering spe...

  • Page 7

    How to use this manual consult the table of contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment. The detailed index ...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owners manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss importan...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped vin location 8 introduction.

  • Page 11: Contents

    Things to know before starting your vehicle contents ! A word about your keys . . . . . . . . . . . . .11 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .11 ▫ locking doors with a key. . . . . . . . . . . . . . . .13 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .13 ! Sentry k...

  • Page 12

    ▫ power window switches . . . . . . . . . . . . . . . . .22 ▫ auto-down . . . . . . . . . . . . . . . . . . . . . . . . . .23 ▫ wind buffeting . . . . . . . . . . . . . . . . . . . . . . .23 ! Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 ! Occupant restraint systems . . . . . ....

  • Page 13

    A word about your keys the key fob contains the remote keyless entry (rke) transmitter with an integrated key. To use the mechanical key simply push the mechanical key release button. The vehicle is supplied with a code card containing key code numbers to order duplicate keys, and the autho- rized d...

  • Page 14

    Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park and re- move the key fob from the vehicle. When leaving the vehicle, always lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children t...

  • Page 15

    Warning! (continued) • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Caution! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unatt...

  • Page 16

    Note: a key which has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle. If the vehicle security light is on after the key is turned to the on/run position, it indicates that there is a problem with the electronics. Cau...

  • Page 17

    General information the sentry key® system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference that may be received, including interference ...

  • Page 18

    To unlock the doors and liftgate push and release the unlock button on the rke transmitter once to unlock the driver’s door or twice, within five seconds, to unlock all doors and the liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also ...

  • Page 19

    1. Push the mechanical key release button and release the mechanical key to access the battery case screw lo- cated on the side of the key fob. 2. Rotate the screw located on the side of the key fob using a small screwdriver. Mechanical key release button key fob screw location 2 things to know befo...

  • Page 20

    3. Take out the battery case. Remove and replace the battery observing its polarity. 4. Refit the battery case inside the key fob and turn the screw to lock it into place. General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to t...

  • Page 21

    If your rke transmitter fails to operate from a normal distance, check for these two conditions: 1. A weak battery in the transmitter. The expected life of the battery is a minimum of three years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile...

  • Page 22

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • for personal security and safety in the event of a collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • before ex...

  • Page 23

    Power door locks — if equipped a power door lock switch is incorporated into the driver door handle. Push or pull the handle to lock or unlock the doors and liftgate. If the driver’s door handle is pushed a red lock indicator will show on the driver’s door handle (indicating locked) when the door is...

  • Page 24

    To change the setting proceed as follows: 1. Briefly push the menu button to enter the menu screen. 2. Push the up or down button to highlight “auto door locks”. Push the menu button, use the up or down buttons to turn setting on or off 3. Briefly push the menu button to go back to the menu screen, ...

  • Page 25

    Auto-down the driver’s door window switch has an auto-down feature. Push the window switch for approximately one second, release, and the window will go down automati- cally. To cancel the auto-down movement, operate the switch in either the up or down direction and release the switch. Wind buffetin...

  • Page 26

    Liftgate to unlock the liftgate, use the remote keyless entry (rke) transmitter or activate the power door lock switches located on the driver door handle. To open the liftgate, squeeze the liftgate release handle and pull the liftgate open with one fluid motion. Liftgate handle 24 things to know be...

  • Page 27

    Warning! • driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • if you are required to drive with the liftgate open, make sure that all windows are c...

  • Page 28

    Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: 1. Children 12 years old and under should always ride buckled up in a vehicle with a rear seat. 2. If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger ...

  • Page 29

    Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint. • only use rear-facing child restraint in a vehicle with a ...

  • Page 30

    After the sequence completes, the seat belt reminder light remains illuminated until the respective seat belts are buckled. The driver should instruct all other occu- pants to buckle their seat belts. If an outboard front seat belt is unbuckled while traveling at speeds greater than 5 mph (8 km/h), ...

  • Page 31

    Warning! • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belt even though you have air bags. • in a collision, you and your p...

  • Page 32

    Warning! (continued) • a lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug. • a twisted seat belt may not pro...

  • Page 33

    Warning! (continued) • a shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. • a frayed or torn seat belt could rip apa...

  • Page 34

    3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt i...

  • Page 35

    5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfort- able and not resting on your neck. The retractor will withdraw any slack in the shoulder belt. 6. To release the seat belt, push the red button on the buckle. The seat belt will automaticall...

  • Page 36

    3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted. Seat belt extender if a seat belt is not long enough to fi...

  • Page 37

    Seat belts and pregnant women we recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the seat belt across the thighs and as snug across the hips as possible. Keep the se...

  • Page 38

    Switchable automatic locking retractor (alr) — if equipped the seat belts in the passenger seating positions may be equipped with a switchable automatic locking retractor (alr) which is used to secure a child restraint system. For additional information, refer to “installing child restraints using t...

  • Page 39

    Driver center passenger first row n/a n/a alr second row alr n/a alr • n/a — not applicable • alr — automatic locking retractor if the passenger seating position is equipped with an alr and is being used for normal usage: only pull the seat belt webbing out far enough to comfortably wrap around the ...

  • Page 40

    How to engage the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire seat belt is extracted. 3. Allow the seat belt to retract. As the seat belt retracts, you will hear a clicking sound. This indicates the seat bel...

  • Page 41

    Supplemental restraint system (srs) air bag system components your vehicle may be equipped with the following air bag system components: • occupant restraint controller (orc) • air bag warning light • steering wheel and column • instrument panel • knee impact bolsters • advanced front air bags • sup...

  • Page 42

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 43

    Advanced front air bag features the advanced front air bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the occupant restraint controller (orc), which may receive information from the front i...

  • Page 44

    Warning! (continued) • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, air bags won’t deploy at all. Al- ways wear your seat belts even though you have air bags. Advanced front air ba...

  • Page 45

    The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the air bags inflate to their full size. The advanced front air bags fully inflate in less time than it takes to blink your eyes. The air bags then quickly deflate while helping to ...

  • Page 46

    The sabs may help to reduce the risk of occupant injury during certain side impacts, in addition to the injury reduction potential provided by the seat belts and body structure. When the sab deploys, it opens the seam on the out- board side of the seatback’s trim cover. The inflating sab deploys thr...

  • Page 47

    • supplemental side air bag inflatable curtains (sabics): located above the side windows. The trim covering the sabics is labeled srs airbag. Sabics may help reduce the risk of head injury to front and rear seat outboard occupants in certain side impacts. Sabics may reduce the risk of injuries in ce...

  • Page 48

    Warning! • your vehicle is equipped with left and right supple- mental side air bag inflatable curtains (sabics). Do not stack luggage or other cargo up high enough to block the deployment of the sabics. The trim covering above the side windows where the sabic and its deployment path are located sho...

  • Page 49

    Compartment. The side air bags may deploy during angled or offset frontal collisions where the advanced front air bags deploy. Side air bags are a supplement to the seat belt restraint system. Side air bags deploy in less time than it takes to blink your eyes. Occupants, including children, who are ...

  • Page 50

    If a deployment occurs the advanced front air bags are designed to deflate immediately after deployment. Note: front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision, which deploys the air bags, any or a...

  • Page 51

    Warning! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the seat belt retractor assemblies replaced by an authorized dealer imme- diately. Also, have the occupant restraint controller system serviced as well. Not...

  • Page 52

    System reset procedure depending on the nature of the event the left and right turn signal lights, located in the instrument panel cluster, may both be blinking and will continue to blink until the ignition switch is turned to the off position. In order to move your vehicle to the side of the road, ...

  • Page 53

    Customer action customer will see 7. Turn left turn signal switch off. (turn signal switch must be placed in neutral state). Left turn light is off. Right turn light is off. 8. Turn ignition off. System is now reset and the engine may be started. 9. Turn hazard flashers off (manually). If a reset pr...

  • Page 54

    Warning light will turn off. If the orc detects a mal- function in any part of the system, it turns on the air bag warning light, either momentarily or continuously. A single chime will sound to alert you if the light comes on again after initial startup. The orc also includes diagnostics that will ...

  • Page 55

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 56

    Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The main purpose of an edr is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per-...

  • Page 57

    Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the united states, and every canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be pros- ecuted for ignoring it. Ch...

  • Page 58

    Note: • for additional information, refer to www.Seatcheck.Org or call 1–866–seatcheck (732–8243). Canadian residents should refer to transport canada’s website for additional information: • www.Tc.Gc.Ca/eng/roadsafety/safedrivers- childsafety-index-53.Htm summary of recommendations for restraining ...

  • Page 59

    Child size, height, weight or age recommended type of child restraint small children children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint forward-facing child restraint with a five-point harness, facing forward in the rear seat...

  • Page 60

    Infants and child restraints safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and conv...

  • Page 61

    Older children and child restraints children who are two years old or who have outgrown their rear-facing convertible child seat can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who are over two years...

  • Page 62

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 63

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 64

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 65

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 2 things to know before starting your vehicle 63.

  • Page 66

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and teth...

  • Page 67

    Can the rear-facing child restraint touch the back of the front passenger seat? Yes the child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint owner’s manual for more information. Can the head restraints be removed?...

  • Page 68

    Locating the upper tether anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the l...

  • Page 69

    To install a latch-compatible child restraint if the selected seating position has a switchable auto- matic locking retractor (alr) seat belt, stow the seat belt, following the instructions below. See the section “installing child restraints using the vehicle seat belt” to check what type of seat be...

  • Page 70

    How to stow an unused alr seat belt: when using the latch attaching system to install a child restraint, stow all alr seat belts that are not being used by other occupants or being used to secure child restraints. An unused belt could injure a child if they play with it and accidentally lock the sea...

  • Page 71

    Installing child restraints using the vehicle seat belt the seat belts in the passenger seating positions are equipped with a switchable automatic locking retractor (alr) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a l...

  • Page 72

    What is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward facing child restraint, ...

  • Page 73

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 74

    9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the seat belt path. It should not move more than 1 inch (25.4 mm) in any direction. Any seat belt system will loosen with time, so check the seat belt occasionally, and pull it tight if necessary. In...

  • Page 75

    2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts. If...

  • Page 76

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 77

    Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem. Safety tip...

  • Page 78

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 79

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 80

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 81

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 83: Contents

    Understanding the features of your vehicle contents ! Power convertible top — if equipped . .84 ▫ lowering the power top. . . . . . . . . . . . . . . . .84 ▫ raising the power top . . . . . . . . . . . . . . . . . .84 ▫ power convertible top relearn procedure . . . . .86 ▫ wind stop . . . . . . . . ...

  • Page 84

    ▫ seat height adjustment . . . . . . . . . . . . . . . . .101 ▫ ez entry feature . . . . . . . . . . . . . . . . . . . . . .101 ▫ memory feature . . . . . . . . . . . . . . . . . . . . . .102 ▫ heated seats — if equipped . . . . . . . . . . . . .103 ▫ head restraints . . . . . . . . . . . . . . . . ...

  • Page 85

    ▫ to resume speed . . . . . . . . . . . . . . . . . . . . .120 ▫ to vary the speed setting . . . . . . . . . . . . . . .120 ▫ to accelerate for passing . . . . . . . . . . . . . . . .121 ! Rear park assist — if equipped . . . . . . . .122 ▫ rear park assist sensors . . . . . . . . . . . . . . . .122...

  • Page 86

    Power convertible top — if equipped on vehicles equipped with a power convertible top, the power convertible top switch is located on the overhead console. The switch contains two buttons. The passenger side button, is used to open the power top, and the driver side button, is used to close the powe...

  • Page 87

    Note: rail lubrication is recommended every 2000 cycles, or if scratching noises due to dust are present. Refer to “fluids, lubes, and genuine part” in “maintain- ing your vehicle” for information. Caution! Failure to follow these cautions may cause interior water damage, stains or mildew on the top...

  • Page 88

    Power convertible top relearn procedure if your power convertible top does not operate in the auto opening/closing mode (automatically opening/ closing to the one-quarter open and three-quarter open comfort stops), or if the trunk lid does not open - the following relearn procedure may be necessary....

  • Page 89

    Wind stop the wind stop installs in the backseat area of the vehicle. The wind stop will not interfere with power top opera- tion. Therefore, it can remain installed when the top is up. Mirrors inside day/night mirror the mirror can be adjusted up, down, left, and right for various drivers. The mirr...

  • Page 90

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activa...

  • Page 91

    Power mirrors the power mirror controls are located on the driver’s door trim panel. The power mirror controls consist of a mirror select switch and a four-way mirror control switch. To adjust a mirror, press the mirror select switch to either the l (left) or r (right) to select the mirror you need ...

  • Page 92

    Spotter mirror — if equipped some models are equipped with a driver’s side spotter mirror. The spotter mirror allows for a greater range of visibility on the driver’s side of the vehicle. Folding mirrors the exterior mirrors are hinged to allow the mirror to pivot forward or rearward to help avoid d...

  • Page 93

    Sun visors the driver and passenger sun visors are located on the headliner, near the front windshield. The sun visor can be rotated downward or up against the door glass. Both sun visors are equipped with courtesy mirrors. Blue&me™ hands-free communication blue&me™ hands-free communication overview...

  • Page 94

    Having to take your eyes off the road or remove your hands from the steering wheel. To use voice commands you are not required to train the voice recognition system to recognize your voice. This implies that the system is nearly equally performing with different persons, i.E.: the voice recognition ...

  • Page 95

    Steering wheel controls and the instrument panel multi- function display. Please refer to the fiat blue & me radio supplement for further information. To get started with blue&me™ hands-free kit with voice recognition, you have to simply pair your bluetooth® wire- less technology enabled mobile phon...

  • Page 96

    • to interact with blue&me™ you can use either the buttons on the steering wheel or voice commands. With voice recognition, you can perform system func- tions by speaking voice commands, also identified as “keywords”. When the system recognizes a keyword, it will respond with the appropriate action....

  • Page 97

    • conference call — you can call another contact while you are engaged in a phone conversation (with bluetooth® phones supporting this option). • call waiting — while engaged in a phone conversa- tion, you can receive notification of another incoming phone call, answer the other incoming phone call,...

  • Page 98

    Note: not all mobile phones support the sms text message reader function or automatic phonebook transfer via bluetooth®. For further information on the list of compatible mobile phones go to http://www.Fiatusa.Com, find the support section near the bottom of web page and click on the bluetooth® logo...

  • Page 99

    Media player with the blue&me™ media player you can play the digital audio files stored on a usb device by simply connecting it to the usb port located in the center console of the car. A second usb port, used for charging only, is located in the glovebox. In this way, while you are driving you can ...

  • Page 100

    • to use the media player, you have to simply connect (directly or by an extension lead) your usb device to the center console usb port. After turning the ignition key to on, blue&me™ will start building your media library. At the end of this operation you can surf the complete library and scroll it...

  • Page 101

    Seats seats are a part of the occupant restraint system of the vehicle. Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of you...

  • Page 102

    While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once the desired position is reached. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Warning! • adjusting a seat while driving may b...

  • Page 103

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Seat height adjustment the driver’s seat height can be raised or lowered by using a le...

  • Page 104

    Lift the seatback upright and push the seat rearward to its locked position once the rear passengers are seated. Memory feature both front seats have a memory feature, which can operate in two ways: memory function option 1 — full seat back and track fore/aft position memory: after using the ez entr...

  • Page 105

    Memory function option 2 — seat back only memory: after using the ez entry function, the seat back may first be returned upright prior to going back to the last fore/aft (memory) position on the tracks. This results in the seat back memory being set only – the track will then be locked forward of it...

  • Page 106

    Warning! (continued) • do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface tempera- ture of the seat. Hea...

  • Page 107

    To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. The reactive head restraints will automatically return to their normal position following a rear imp...

  • Page 108

    Rear head restraints to raise the head restraint, pull upward on the head re- straint. To lower the head restraint, press the push button, located at the base of the head restraint, and push down- ward on the head restraint. Refer to “occupant restraints” in “things to know before starting your vehi...

  • Page 109

    2. Rotate the safety catch under the front edge of the hood, near the center, and raise the hood. 3. Lift the hood prop rod that clips to the right side (left side when standing in front of the hood) of the engine compartment. Place the hood prop rod in the hole of hood hinge to secure the hood in t...

  • Page 110

    Caution! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. Warning! Be sure the hood is fu...

  • Page 111

    Note: when the headlights are turned on, the daytime running lights will be deactivated. High beams with the low beams activated, push the multi- function lever towards the instrument panel to turn on the high beams. Pull the multifunction lever toward the steering wheel to turn off the high beams. ...

  • Page 112

    Daytime running lights — if equipped to activate the daytime running lights (drl), rotate the end of the multifunction lever to the o symbol. Note: the low beams and side/taillights will not be on with drl. If allowed by law in the country in which the vehicle was purchased the drl function can be t...

  • Page 113

    Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Follow me home/headlight delay when this feature is selected the driver can choose to have the headlights remain on for a preset...

  • Page 114

    Caution! Before getting out of the vehicle be sure that the switch is in the center position or that the lights are off to avoid draining the battery. Interior light timing (center position) there are four different modes of operation that can be activated in this position: • when one door is opened...

  • Page 115

    Front fog lights — if equipped the fog light switch is located on the center stack of the instrument panel, just below the radio. Press the switch once to turn the front fog lights on. Press the switch a second time to turn the front fog lights off. Windshield wipers and washers the windshield wiper...

  • Page 116

    Front windshield wiper operation there are five different modes of operation for the front windshield wipers. The windshield wiper lever can be raised or lowered to access these modes: windshield wiper off this is the normal position of the wiper lever. Intermittent wiper operation push the lever do...

  • Page 117

    Manual high speed/mist push the lever upward from the off position. The wipers will operate at high speed to clear off road mist or spray from a passing vehicle. This operation will continue until the lever is released. When the lever is released, the wipers will return to the off position and autom...

  • Page 118

    Rear windshield wiper rotate the end of the windshield wiper/washer lever upward to the first detent past the intermittent settings for intermittent wipe operation. With the front wind- shield wiper active, rotate the end of the windshield wiper/washer lever upward. The rear wiper will operate in th...

  • Page 119

    Rear windshield washer operation push the windshield wiper/washer lever toward the instrument panel to activate the rear washer. Push and hold the lever for more than a half second and the wipers will activate automatically for three cycles after the lever is released. Tilt steering column — if equi...

  • Page 120

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Electronic speed control ...

  • Page 121

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 122

    To deactivate a soft tap on the brake pedal, pushing the canc button, or normal brake pressure while slowing the vehicle will deactivate electronic speed control without erasing the set speed memory. Pressing the on/off button or turning the ignition switch off erases the set speed in memory. To res...

  • Page 123

    • if the button is continually pressed, the set speed will continue to increase until the button is released, then the new set speed will be established. To decrease speed when the electronic speed control is set, you can de- crease speed by pushing the set (-) button. The drivers preferred units ca...

  • Page 124

    Using electronic speed control on hills the transmission may downshift on hills to maintain the vehicle set speed. Note: the electronic speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. On steep hills, a greater speed loss or gain may occur so...

  • Page 125

    If several obstacles are detected, the rear park assist system indicates the nearest obstacle. The minimum height of a detectable obstacle corresponds to the maximum height of an obstacle that would clear the underside of the car during the parking maneuver. Rear park assist warning display the rear...

  • Page 126

    Rear park assist audible alerts if an obstacle is behind the vehicle when the transmission is placed into reverse, an audible alert is activated. The tones emitted by the loudspeaker inform the driver that the vehicle is approaching an obstacle. The pauses between the tones are directly proportional...

  • Page 127

    Signal meaning indication failure sensor or system failures visual signal (instrument panel) • icon appears on display. • message is displayed on the electronic vehicle infor- mation center (evic) (where provided). While audible signals are emitted, the audio system is not muted. The audible signal ...

  • Page 128

    The sensors and wiring are tested continuously when the ignition is in the on/run position. Failures are indi- cated immediately if they occur when the system is on. Even if the system is able to identify that a specific sensor is in failure condition, the evic shall indicate that the rear park assi...

  • Page 129

    • objects such as bicycle carriers, etc., must not be placed within 12 in (30 cm) from the rear fascia/ bumper while driving the vehicle. Failure to do so can result in the system misinterpreting a close object as a sensor problem, causing a failure indication to be displayed in the instrument clust...

  • Page 130

    Warning! (continued) • before using the rear park assist system, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the ve- hicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hit...

  • Page 131

    Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location acces- sible to children. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sun...

  • Page 132

    Pinch protect feature this feature will detect an obstruction in the opening of the sunroof during express close operation. If an ob- struction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the switch forward and ...

  • Page 133

    Electrical power outlets there is a standard 12 volt (13 amp) power outlet, located in the floor console, for added convenience. This power outlet can power mobile phones, electronics and other low power devices. Power is available when the ignition switch is in the on/run or start position. Insert ...

  • Page 134

    Caution! • do not exceed the maximum power of 160 watts (13 amps) at 12 volts. If the 160 watts (13 amps) power rating is exceeded, the fuse protecting the system will need to be replaced. • power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as t...

  • Page 135

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 136

    Cigar lighter — if equipped this is located on the center console, in front of the cup holders. To activate the cigar lighter, push and release the knob. After a few seconds the knob automatically returns to its initial position, and the cigar lighter is ready for use. Warning! When the cigar lighte...

  • Page 137

    For rear passengers, there are cupholders located on the floor between the front driver and passenger seats. Storage glove compartment the glove compartment is located on the right side of the instrument panel. Pull outward on the glove compart- ment latch to open the glove compartment. Push the glo...

  • Page 138

    Cargo area features the rear seatbacks have a fold down feature to allow increased cargo capacity. Push down the release button, located at the outboard top of the seatback and move the seatback to its folded- down position to provide a flat load floor cargo area. When returning the seatback to its ...

  • Page 139

    Rear window features rear window defroster the rear window defroster button is located in the center of the instrument panel, below the radio. Press this button to turn on the rear window defroster. An indicator in the instrument cluster will illuminate when the rear window defroster is on. The rear...

  • Page 140

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 141: Contents

    Understanding your instrument panel contents ! Instrument panel features . . . . . . . . . .141 ! Instrument cluster . . . . . . . . . . . . . . . . .142 ! Instrument cluster — eco . . . . . . . . . . .143 ! Instrument cluster — pop, lounge, 500c . . . . . . . . . . . . . . . . . . . . . . . .144 ! ...

  • Page 142

    ▫ introduction . . . . . . . . . . . . . . . . . . . . . . . . .181 ▫ suggestions. . . . . . . . . . . . . . . . . . . . . . . . . .181 ▫ technical specifications . . . . . . . . . . . . . . . . .183 ▫ quick guide . . . . . . . . . . . . . . . . . . . . . . . . .184 ▫ general information. . . . . . ...

  • Page 143

    Instrument panel features 1 — side vent 7 — passenger air bag 13 — storage compartment 2 — multifunction lever – light control 8 — glove compartment 14 — shift lever 3 — instrument cluster and warning lights 9 — rear defrost button 15 — sport button 4 — windshield wiper, washer, trip computer 10 — h...

  • Page 144

    Instrument cluster 142 understanding your instrument panel.

  • Page 145

    Instrument cluster — eco 4 understanding your instrument panel 143.

  • Page 146

    Instrument cluster — pop, lounge, 500c 144 understanding your instrument panel.

  • Page 147

    Instrument cluster descriptions 1. Tire pressure monitoring telltale light — if equipped each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure ...

  • Page 148

    When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. Tpms malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the tpms from functi...

  • Page 149

    3. Turn signal indicators the arrow will flash with the exterior turn signal when the turn signal lever is operated. Note: • a continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on. • check for an inoperative outside light bulb if either indicator ...

  • Page 150

    Note: • the “esc off indicator light” and the “esc activation/malfunction indicator light” come on momentarily each time the ignition switch is turned to on/run. • each time the ignition is turned to on/run, the esc system will be on, even if it was turned off previously. • the esc system will make ...

  • Page 151

    8. Seat belt reminder light when the ignition switch is first turned to on/run, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver’s seat belt remain...

  • Page 152

    Caution! Prolonged driving with the malfunction indicator light (mil) on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the mil is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. Warni...

  • Page 153

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 154

    The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a...

  • Page 155

    Operation of the brake warning light can be checked by turning the ignition switch from the off position to the on/run position. The light should illuminate for ap- proximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light ...

  • Page 156

    16. Gas pedal percentage gauge/turbo gauge/ eco index gauge depending on what options and trim level your vehicle is equipped with there are three gauges available. • gas pedal percentage gauge: this gauge shows what percent the gas pedal is currently depressed at. • turbo gauge: this gauge shows th...

  • Page 157

    18. Electronic vehicle information center (evic) the evic features a driver-interactive display that is located in the instrument cluster. For further information, refer to “electronic vehicle information center (evic)” in “understanding your instrument panel.” 19. Temperature gauge the temperature ...

  • Page 158

    20. Tachometer the tachometer indicates engine speed in revolutions per minute (rpm x 1000). 21. Speedometer / trip odometer / electronic vehicle information center (evic) display area this display indicates the total distance the vehicle has been driven. U.S. Federal regulations require that upon t...

  • Page 159

    23. Generic warning light the generic warning light will illuminate if any of the following conditions occur: oil change request, engine oil pressure sensor failure, external light failure, fuel cut-off intervention, fuel cut-off not available, parking sensor failure. 24. Cruise on indicator — if eq...

  • Page 160

    26. Electronic throttle control (etc) light this light informs you of a problem with the electronic throttle control (etc) system. If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is place...

  • Page 161

    If the light turns on while driving, safely pull over and stop the vehicle. If the a/c system is on, turn it off. Also, shift the transmission into neutral and idle the ve- hicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “if...

  • Page 162

    The evic consists of the following: • system status • vehicle information warning message displays • personal settings (customer-programmable features) • outside temperature display • trip computer functions • tire pressure monitoring display evic displays 1. Red telltales (left bank) • hood ajar • ...

  • Page 163

    • door ajar • speed limiter — if equipped 2. Amber telltales • ice risk • fuel cut off • fuel cut off failed • hill holder failed • oil change request • check lights • vehicle lock 3. Electronic speed control active 4. Amber telltales • generic warning light • glow plug light • park sensor failed • ...

  • Page 164

    Push and release the down button to scroll down- ward through the displayed menu and the related options or to decrease the value displayed. Note: up and down buttons activate differ- ent functions according to the following situations: • to scroll the menu options upwards or downwards. • to increas...

  • Page 165

    • see radio • speed display • autoclose • units • language • buzzer volume • button volume • daylights (d.R.L.) • hill start • tire pressure • unlock driver door first • unlock all doors • exit menu selecting an option of the main menu without submenu 1. Briefly push and release the menu button to s...

  • Page 166

    3. Briefly push and release the menu button to select the displayed submenu option and to open the rel- evant setup menu. 4. Push and release the up or down button (by single pushes) to select the new setting for this submenu option. 5. Briefly push and release the menu button to store the new setti...

  • Page 167

    Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. Trip computer the trip computer is located in the instrument cluster. It features a driver-interactive display (displays informa- tion such as tr...

  • Page 168

    Start of trip procedure with the ignition on, push and hold the trip button for over one second to reset. Exit trip to exit the trip function, wait until all the values have been displayed or hold the menu button for longer than one second. Briefly push and release the menu button to go back to the ...

  • Page 169

    Values displayed range this indicates the distance which may be traveled with the fuel remaining in the tank, assuming that driving conditions will not change. The message “----” will appear on the display in the following cases: • distance less than 30 miles (or 50 km). • the vehicle is parked for ...

  • Page 170

    Personal settings (customer-programmable features) dimmer the evic display is provided with a light sensor capable of detecting environmental light conditions and adjust- ing the brightness of the instruments accordingly. Note: the brightness of the instrument panel may change while travelling follo...

  • Page 171

    Note: the setting can be increased or decreased by 5 mph or km/h each time the up/down button is pushed for speed settings above 20 mph (32 km/h). To increase or decrease the set speed rapidly, push and hold the up/down button. Save the setting by briefly push- ing the button when you approach the r...

  • Page 172

    3. Briefly push and release the menu button to go back to the menu screen, or push and hold the menu button (approximately one second) to go back to the main screen without storing the settings. Set time (clock) this function may be used to set the clock through two submenu items: “time” and “mode.”...

  • Page 173

    • briefly push and release the menu button to return to the “time” sub-function. • when accessing the “mode” submenu, briefly push and release the menu button. The previously set display format will flash on the display. • push and release the up or down button to select “24h” or “12h.” when you hav...

  • Page 174

    Note: the setting will increase or decrease by one unit each time the up or down button is pushed. Push and hold the up or down button to increase/decrease the setting rapidly. Save the setting by briefly pushing the button when you approach the required setting. • briefly push and release the menu ...

  • Page 175

    Speed display when this function is activated the cluster will display the vehicle speed (mph or km/h). To activate (on) or to deactivate (off) the speed display feature, proceed as follows: 1. Briefly push and release the menu button. Push and release the up or down button to highlight speed displa...

  • Page 176

    Units (set units) this function may be used to set the measurement unit in three submenus: “distance,” “temperature” and “fuel economy, and tire pressure.” to set the required unit, proceed as follows: 1. Briefly push and release the menu button. Push and release the up or down button to highlight u...

  • Page 177

    3. When accessing the “temperature” submenu: briefly push and release the menu button. Either “°f” or “°c” will appear on the display (according to the previous setting). 4. Push and release the up or down button for setting. 5. Briefly push and release the menu button to return to the tire pressure...

  • Page 178

    Buzzer volume (adjusting the failure/warning buzzer volume) with this function the volume of the buzzer accompany- ing any failure/warning indication can be adjusted to one of eight volume levels. To adjust the volume proceed as follows: 1. Briefly push and release the menu button. Push and release ...

  • Page 179

    Belt buzzer (buzzer activation for s.B.R. Indication) this function will only be displayed after a fiat group automobiles dealership has deactivated the s.B.R. System. Daytime running lamps (drl) this function may be used to activate / deactivate the daytime running lamps. Proceed as follows to swit...

  • Page 180

    To set the required unit, proceed as follows: 1. Briefly push and release the menu button to display the two sub-menus. 2. Push and release the up or down button to navigate the two sub-menus. 3. Select the required sub-menu and then briefly push and release the menu button. 4. Push and release the ...

  • Page 181

    Tire pressure this function will be used to display the tire pressures individually for all four tires by location. Proceed as follows: 1. Briefly push and release the menu button. Push and release the up or down button to highlight the tire pressure. Push and release the menu button to enter the ti...

  • Page 182

    Exit menu this function closes the initial menu screen. Briefly push and release the menu button to go back to the main screen. Push and release the button to return to the first menu option (speed beep). Push and release the button to return to the last menu option (daylights). Sales code (rab) rad...

  • Page 183

    Introduction the radio has been designed according to the specifica- tions of the passenger compartment, with a personalized design to match the style of the dashboard. If the radio has blue&me™, refer to the appropriate “blue&me™ user’s manual” for further information. The instructions for use are ...

  • Page 184

    Cds the presence of dirt, scratches or distortions on the cds could cause skipping and poor sound quality while it is playing. For optimal playback conditions, follow these guidelines: • only use branded cds. • clean every cd thoroughly removing any finger marks or dust using a soft cloth. Hold cds ...

  • Page 185

    • if a copy-protected cd is used, it may take a few seconds before the system starts to play it. The cd player cannot be guaranteed to play all protected discs. The fact that the cd is protected from being copied is often shown in very small letters or is difficult to read on the actual cd cover whe...

  • Page 186

    With alpine premium audio system (if equipped): • two 165 mm diameter midwoofer speakers. • two 11 mm tweeter speakers in the front pillars. • two 100 mm full range speakers, one speaker in each of the rear side panels. • an amplifier in the trunk on the right-hand side panel. • antenna on the car r...

  • Page 187

    Button general functions mode media cd/aux/media player (if equipped and present) source selection short repeated button push button general functions mode (mute/pause button) volume activation/deactivation (mute/pause) short button push audio audio adjustments: low tones (bass), high tones (treble)...

  • Page 188

    Button general functions mode menu advanced functions adjustment menu activation: short button push adjustment type selection: push or adjustment of values: push or +vol/–vol volume adjustment push + button: volume increase push – button: volume decrease button radio functions mode radio station sea...

  • Page 189

    Button cd functions mode cd ejection short button push previous/next track play short button push or cd track fast forward/rewind long button push or previous/next folder play (for cd-mp3) short button push or general information the radio offers the following functions: radio section • pll tuning w...

  • Page 190

    Cd section • track selection (forward/backward) • fast forward/rewind through tracks • cd display function: display of track number and on mp3 discs (song title, artist) and time elapsed since start of the track • playing audio cd, cd-r and cd-rw caution! On multimedia cds, besides audio tracks, the...

  • Page 191

    Functions and adjustments turning the car radio on the car radio comes on when the (on/off) button is pushed briefly. When the car radio is turned on and the on volume limit is on, the volume is limited to a setting of five even if it had been set higher when previously used. Turning the car radio o...

  • Page 192

    When the volume level is changed using the dedicated controls, the mute function is deactivated and the vol- ume is adjusted to the new level selected. Audio adjustment the functions that can be selected from the audio menu change depending on the context: am/fm/media/ satellite. Push the audio butt...

  • Page 193

    Tone adjustment proceed as follows: 1. Push the audio button. 2. Push the or button to select “bass,” “mid- range” or “treble” in the audio menu. 3. Push the or button to increase/decrease the bass or treble adjustments. By pushing the or buttons briefly, the levels will change progressively. By pus...

  • Page 194

    Fader adjustment proceed as follows: 1. Push the audio button. 2. Push the or button to set “fader” in the audio menu. 3. Push the button to increase the sound coming from the rear speakers or the button to increase the sound coming from the front speakers. By pushing the or buttons briefly, the lev...

  • Page 195

    To activate the equalizer, use the audio button to select one of the adjustments: • “eq user” (adjustment of 7 equalizer bands that can be changed by the user) • “classic” (equalizer preset for optimal classic music sound) • “rock” (equalizer preset for optimal rock and pop music sound) • “jazz” (eq...

  • Page 196

    Menu menu button functions push the menu button briefly to activate the menu function. Use the or buttons to scroll through the menu functions. To change the setting of the selected func- tion, use the or buttons. The current status of the selected function appears on the display. The functions mana...

  • Page 197

    On volume limit this function makes it possible to activate/deactivate the maximum volume limit when turning the radio on. The display shows the function status: • “on volume limit: on” – when the radio is turned on the volume level will be: – if the volume level is equal to or higher than the maxim...

  • Page 198

    Radio off function this function makes it possible to set the radio switching off mode by choosing between two methods. The chosen mode appears on the display: • “radio off: 00 min” — the radio turns off in connec- tion with the ignition key; the radio is turned auto- matically off as soon as the ke...

  • Page 199

    Once the radio mode has been activated, the display will show the name (rbds stations only) or the frequency of the selected radio station, the frequency band selected (e.G. Fma) and the preset button number (e.G. P1). Frequency band selection with the radio mode active, press the fm or am tuner but...

  • Page 200

    Automatic tuning briefly push the or button to start the automatic tuning search for the next station that can be received in the selected direction. If the or button is pushed for longer, the rapid search is started. When the button is released, the tuner will stop on the next station that can be r...

  • Page 201

    Logos are trademarks of siriusxm radio inc. And its subsid- iaries. Siriusxm radio requires a subscription, sold sepa- rately after trial subscription included with vehicle pur- chase. Prices and programming are provided by siriusxm and are subject to change. Subscriptions governed by terms & condit...

  • Page 202

    Write down the electronic serial number (esn) for your receiver. To retrieve the electronic serial number of siriusxm satellite receiver module tune to channel 0. Make sure that when the order is placed, the esn are correct. If any of the esn numbers are not entered correctly, then the siriusxm subs...

  • Page 203

    The following are instructions for retrieving the elec- tronic serial number (esn) from fiat 500 nafta model radios: to retrieve the esn of sirius satellite receiver module tune to channel 0. Make sure that when the order is placed, the esn are correct. If any of the esn numbers are not entered corr...

  • Page 204

    It is advisable to use original cds to ensure optimal playing. If cd-r/rws are used, we recommend using good quality media that are burned at the slowest speed possible. Cd loading/ejecting to load the cd, insert it gently into the slot to activate the motorized loading system, which will position i...

  • Page 205

    A cd which cannot be read will not be ejected until these functions are over. At the end, with the cd mode activated, the display will show the wording “cd disc error” for a few seconds and then the cd will be ejected. Display information when the cd player is operating, information will ap- pear on...

  • Page 206

    Cd mp3 player introduction this chapter describes the operation of the cd mp3 player. Note: layer-3 audio decoding technology is licensed from fraunhofer iis and thomson multimedia. Mp3 mode in addition to playing regular audio cds, the radio is also enabled to play cdroms on which compressed audio ...

  • Page 207

    Selecting mp3 sessions with hybrid discs if a hybrid disc is inserted (mixed mode, enhanced, cd-extra) also containing mp3 files, the radio automati- cally starts playing the audio session. It is possible to move to the mp3 session while playing by keeping the cd button pressed for more than two sec...

  • Page 208

    Structure of the folders the radio with mp3 player: • recognizes only the folders that effectively contain mp3 format files. • if the mp3 files on a cd-rom are structured in sub-folders their structure is compressed to a single level structure, where the sub-folders are taken to the level of the mai...

  • Page 209

    The duration of the mp3 tracks is not correctly displayed: in some cases (due to the recording mode) the duration of the mp3 tracks can be displayed incorrectly. Operating instructions — hands-free phone refer to the appropriate “blue&me™ user’s manual” for further information. Personal/portable nav...

  • Page 210

    Steering wheel audio controls the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pu...

  • Page 211

    Radio operation pushing the top of the switch will “seek” up for the next listenable station and pushing the bottom of the switch will “seek” down for the next listenable station. The button located in the center of the left-hand control will tune to the next preset station that you have pro- gramme...

  • Page 212

    4. Do not use solvents such as benzene, thinner, cleaners, or anti-static sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. Note: if you experience difficulty in playing a particular dis...

  • Page 213

    Manual heating and air conditioning the manual climate controls consist of a series of rotary dials and one inner push knob. 1. Temperature control rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial to the left into the blue area of the sca...

  • Page 214

    Note: • continuous use of the recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. • the use of the recirculation mode in cold or damp weather could cause windows to fog on the inside, because of moisture buildup inside the veh...

  • Page 215

    Require extra heat to the windshield. This setting is good for maintaining comfort while reducing mois- ture on the windshield. • defrost air is directed through the windshield and side window demister outlets. Use this mode with maximum blower and temperature settings for best windshield and side w...

  • Page 216

    The atc system automatically maintains the interior comfort level desired by the occupant. 1. Auto temperature control (atc) button controls airflow, temperature, distribution, and air recir- culation automatically. Push and release to select. Per- forming this function will cause the atc to switch ...

  • Page 217

    The blower fan speed may be set to any fixed speed by pushing the blower control up or down buttons. The fan will now operate at a fixed speed until additional speeds are selected. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the auto mode. The op...

  • Page 218

    8. Panel mode air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. Performing this function will cause the atc to switch into manual mode. Note: the center instrument panel outlets can be aimed so that they are directed toward the rear seat ...

  • Page 219

    Climate control functions air conditioning (a/c) the air conditioning (a/c) button allows the operator to manually activate or deactivate the air conditioning system. When in a/c mode with the atc set to a cool temperature, dehumidified air flows through the air outlets. If economy mode is desired, ...

  • Page 220

    Automatic operation 1. Push the auto button on the automatic temperature control (atc) panel, the indicator will illuminate when on. 2. Next, adjust the temperature you would like the system to maintain by adjusting the temperature con- trol buttons. Once the desired temperature is dis- played, the ...

  • Page 221

    Manual operation the system allows for manual selection of blower speed, air distribution mode, a/c status and recirculation con- trol. The blower fan speed can be set to any fixed speed by adjusting the blower control. The fan will now operate at a fixed speed until additional speeds are selected. ...

  • Page 222

    Note: automatic temperature controls (atc) will au- tomatically adjust the climate control settings to reduce or eliminate window fogging on the front windshield. When this occurs, recirculation will be unavailable. Summer operation note: in some cases during high temperature opera- tion, the air co...

  • Page 223

    Operating tips chart 4 understanding your instrument panel 221.

  • Page 225: Starting And Operating

    Starting and operating contents ! Starting procedures . . . . . . . . . . . . . . . .227 ▫ manual transmission — if equipped . . . . . . .227 ▫ automatic transmission — if equipped . . . . .227 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .228 ▫ cold weather operation . . . . . . . ....

  • Page 226

    ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . . .242 ! Driving on slippery surfaces . . . . . . . . .244 ▫ acceleration . . . . . . . . . . . . . . . . . . . . . . . . .244 ▫ traction . . . . . . . . . . . . . . . . . . . . . . . . . . . .244 ! Driving through water . . . . . . . . ....

  • Page 227

    ! Tires — general information . . . . . . . .273 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . . .273 ▫ tire inflation pressures . . . . . . . . . . . . . . . . .275 ▫ tire pressures for high speed operation . . . .276 ▫ radial ply tires . . . . . . . . . . . . . . . . . . . . . .276 ▫...

  • Page 228

    ▫ materials added to fuel . . . . . . . . . . . . . . . .301 ▫ fuel system cautions. . . . . . . . . . . . . . . . . . .302 ▫ carbon monoxide warnings . . . . . . . . . . . . .303 ! Adding fuel . . . . . . . . . . . . . . . . . . . . . . . .303 ▫ fuel filler cap (gas cap) . . . . . . . . . . . . . ....

  • Page 229

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a numb...

  • Page 230

    Normal starting note: normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal. Turn the ignition switch to the avv/acc (start) position and release it when the engine starts. If the engine fails to start within 10 seconds, turn the ignition swi...

  • Page 231

    2. Cycle the ignition in the start position and release it when the engine starts. 3. If the engine fails to start within ten seconds, cycle the ignition to the stop (off/lock) position, wait five seconds to allow the starter to cool, then repeat the extended park starting procedure. 4. If the engin...

  • Page 232

    Caution! (continued) • to prevent damage to the starter, do not continu- ously crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. After starting the idle speed is controlled automatically and it will decrease as the engine warms up. Turbocharger “cool dow...

  • Page 233

    Fully press the clutch pedal before you shift gears. As you release the clutch pedal, lightly press the accelerator pedal. Note: to shift into reverse from neutral, lift the ring under the knob and, at the same time move the gearshift lever to the right and then backward. Use each gear in numerical ...

  • Page 234

    Note: • clashing reverse gear, especially if vehicle is mov- ing, can result in transmission damage. • during cold weather, until the transmission lubricant is warm, you may experience slightly higher shift efforts. This is normal and not harmful to the trans- mission. Recommended shift speeds to us...

  • Page 235

    Downshifting proper downshifting will improve fuel economy and prolong engine life. Caution! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released. Damage...

  • Page 236

    Warning! • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something. Only shift ...

  • Page 237

    Key ignition park interlock this vehicle is equipped with a key ignition park inter- lock which requires the transmission to be in park before the ignition switch can be turned to the lock/ off (key removal) position. The key can only be re- moved from the ignition when the ignition is in the lock/o...

  • Page 238

    Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears. The transmission shift lever has park, reverse, neu- tral, drive, and autostick shift positions. Manual shifts c...

  • Page 239

    Gear ranges do not race the engine when shifting from park or neutral into another gear range. Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park (p) this range supplements the parki...

  • Page 240

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 241

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off position to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ...

  • Page 242

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 243

    If the transmission temperature exceeds normal operating limits, the transmission controller will expand the range of torque converter clutch engagement. This is done to pre- vent transmission damage due to overheating. During cold temperatures, transmission operation may be modified depending on en...

  • Page 244

    Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, authorized dealer service is required...

  • Page 245

    • the transmission will automatically downshift to first gear when coming to a stop. After a stop, the driver should manually upshift (+) the transmission as the vehicle is accelerated. • you can start out (from a stop) in first, second, or third gear. Starting out in second or third gear can be hel...

  • Page 246

    Driving on slippery surfaces acceleration rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the driving wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels. Warning! ...

  • Page 247

    Driving through water driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. Flowing/rising water warning! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flow...

  • Page 248

    Caution! • always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • determine the condition of the road or the path that is under water and if there are any obstacles in the wa...

  • Page 249

    Power steering the electric power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will vary its assist to provide light efforts while parking and good feel while driving. If the electric steering system experiences a fault that pr...

  • Page 250

    Note: • even if the power steering assistance is no longer operational, it is still possible to steer the vehicle. Under these conditions there will be a substantial increase in steering effort, especially at low speeds and during parking maneuvers. • if the condition persists, see your authorized d...

  • Page 251

    When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. Warning! • never leave children alone in a vehicle, or with access to ...

  • Page 252

    Caution! If the brake warning light remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. Sport mode manual transmission — if equipped the sport mode increases steering feedback to the driver with slig...

  • Page 253

    Automatic transmission — if equipped the sport mode increases steering feedback to the driver with slight increase in effort and changes the transmis- sion shift schedules for more aggressive shifting. This driving mode is useful while driving on twisty roads where more steering precision is desired...

  • Page 254

    Brake system your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability, the remaining system will still func- tion. However, there will be some loss of overall braking effectiveness. You may notice increased pedal travel during applica...

  • Page 255

    The abs includes an amber abs warning light. When the light is illuminated, the abs is not functioning. The system reverts to standard non-anti-lock brakes. Turning the ignition off and on again may reset the abs if the fault detected was only momentary. Warning! • pumping the anti-lock brakes will ...

  • Page 256

    Brake assist system (bas) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce...

  • Page 257

    Traction control system (tcs) this system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the tcs system, brake limit...

  • Page 258

    Hsa activation criteria the following criteria must be met in order for hsa to activate: • vehicle must be stopped. • vehicle must be on a 2.5% (manual transmission) or 7% grade or greater (automatic transmission) hill. • gear selection matches vehicle uphill direction (i.E., vehicle in neutral (man...

  • Page 259

    Electronic stability control (esc) the electronic stability control (esc) system enhances directional control and stability of the vehicle under various driving conditions. Esc corrects for oversteering or understeering of the vehicle by applying the brake of the appropriate wheel to assist in count...

  • Page 260

    Note: the esc off switch is located left of the steering column (manual transmission only). Warning! The electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esc cannot pre...

  • Page 261

    Esc operating modes the esc system has two available operating modes. Full on this is the normal operating mode for esc. Whenever the vehicle is started, the esc system will be in on mode. This mode should be used for most driving situations. Esc should only be turned to partial off for specific rea...

  • Page 262

    Esc activation/malfunction indicator light and esc off indicator light the esc activation/malfunction indicator light in the instrument cluster will come on when the ignition switch is turned to the mar (acc/on/run) position for four seconds. If the esc activation/malfunction indicator light comes o...

  • Page 263

    Tire safety information tire markings note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design stand...

  • Page 264

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it beg...

  • Page 265

    Example: 65, 85, 80 = aspect ratio in percent (%) – ratio of section height to section width of tire, or 10.5 = section width in inches (in) r = construction code – #r# means radial construction, or – #d# means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service descriptio...

  • Page 266

    Example: h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – the maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.E., tire press...

  • Page 267

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 268

    Example: dot ma l9 abcd 0301 01 = number representing the year in which the tire was manufactured (two digits) – 01 means the year 2001 – prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured. Example: 031 could represen...

  • Page 269

    Term definition maximum inflation pressure the maximum inflation pressure is the maximum permissible cold tire inflation pressure for this tire. The maximum inflation pressure is molded into the sidewall. Recommended cold tire inflation pressure vehicle manufacturer’s recommended cold tire inflation...

  • Page 270

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) example tire placard location (b-pillar) 268 starting an...

  • Page 271

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 272

    Note: under a maximum loaded vehicle condition, gross axle weight ratings (gawrs) for the front and rear axles must not be exceeded. For further information on gawrs, vehicle loading, and trailer towing, refer to “vehicle loading” in this section. To determine the maximum loading conditions of your ...

  • Page 273

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 274

    272 starting and operating.

  • Page 275

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 276

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the v...

  • Page 277

    Tire inflation pressures the proper cold tire inflation pressure is listed on the driver’s side b-pillar or rear edge of the driver’s side door. At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judgement when determining pro...

  • Page 278

    Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too low. Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits ...

  • Page 279

    Tire repair if your tire becomes damaged, it may be repaired if it meets the following criteria: • the tire has not been driven on when flat. • the damage is only on the tread section of your tire (sidewall damage is not repairable). • the puncture is no greater than a ¼ of an inch (6 mm). Consult a...

  • Page 280

    Driving conditions. Install winter tires on your vehicle when ambient temperatures are less than 40°f (5°c) or if roads are covered with ice or snow. For more informa- tion, contact an authorized dealer. Summer tires do not contain the all season designation or mountain/snowflake symbol on the tire ...

  • Page 281

    While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states pro- hibit studded tires; therefore, local laws should be checked before using these tire types. Run flat tires — if equipped run flat tires a...

  • Page 282

    Spare tire matching original equipped tire and wheel — if equipped your vehicle may be equipped with a spare tire and wheel equivalent in look and function to the original equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for y...

  • Page 283

    Warning! (continued) replaced. Be sure to follow the warnings, which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control. Full size spare — if equipped the full size spare is for temporary emergency use only. This tire may look like the originally equ...

  • Page 284

    Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressures listed on your tire and loading inf...

  • Page 285

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (2 mm). When the t...

  • Page 286

    • performance tires, tires with a speed rating of v or higher, and summer tires typically have a reduced tread life. Rotation of these tires per the vehicle main- tenance schedule is highly recommended. Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining...

  • Page 287

    It is recommended to replace the two front tires or two rear tires as a pair. Replacing just one tire can seriously affect your vehicle’s handling. If you ever replace a wheel, make sure that the wheel’s specifications match those of the original wheels. It is recommended you contact your authorized...

  • Page 288

    Caution! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Tire chains (traction devices) use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard against damage: • traction device must be ...

  • Page 289

    Caution! (continued) • install device as tightly as possible and then re- tighten after driving about ½ mile (0.8 km). • do not exceed 30 mph (48 km/h). • drive cautiously and avoid severe turns and large bumps, especially with a loaded vehicle. • do not drive for a prolonged period on dry pave- men...

  • Page 290

    The suggested rotation method is the “rearward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed. Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure b...

  • Page 291

    The tpms will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning limit for any reason, including low temperature effects, or natural pressure loss through the tire. The tpms will continue to warn the driver of low tire pressure as long as the condition e...

  • Page 292

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, ...

  • Page 293

    • driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. • the tpms is not a substitute for proper tire mainte- nance, and i...

  • Page 294

    Tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illumi- nate in the instrument cluster, an audible chime will be activated, and the “check left or right front/rear tire xxx.X psi” text message will display when one or more of the four active road tire ...

  • Page 295

    Note: your vehicle may be equipped with a compact spare wheel and tire assembly. 1. The compact spare tire does not have a tire pressure monitoring sensor. Therefore, the tpms will not moni- tor the tire pressure in the compact spare tire. 2. If you install the compact spare tire in place of a road ...

  • Page 296

    Enhanced system — if equipped when the vehicle is equipped with an enhanced tpm system, the driver can view text messages showing the actual tire pressure value by position by selecting the tire pressure menu command in the instrument cluster. Refer to the instrument panel features section of the ow...

  • Page 297

    Should this occur, you should stop as soon as possible and inflate the tires with low pressure to the vehicle’s recom- mended cold placard pressure value. Once the system receives the updated tire pressures, the system will auto- matically update and the “tire pressure monitoring telltale light” wil...

  • Page 298

    If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “tire pressure monitoring telltale light” will no longer flash, and the “service tire pressure monitoring system” message will no longer display, and a pres...

  • Page 299

    Shown. This indicates that the pressure values are still being received from the tpm sensors but they may not be located in the correct vehicle position. The system still needs to be serviced as long as the #service tire pressure monitoring system# message is displayed. Note: • the tpms will not mon...

  • Page 300

    Pressure value instead of dashes (- -), as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this information. General information this ...

  • Page 301

    Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required. Poor quality gasoline can cause problems such as hard starting, stalling and hesitations. If you experience these symptoms, tr...

  • Page 302

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, methyl tert-butyl ether (mtbe), and ethyl tret-butyl ether (etbe). Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels ble...

  • Page 303

    To fix a non-ffv vehicle inadvertently fueled once with e-85 perform the following: • drain the fuel tank (see your authorized dealer). • change the engine oil and oil filter. • disconnect and reconnect the battery to reset the engine controller memory. More extensive repairs will be required for pr...

  • Page 304

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gas is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance and damage the emissions control system. • an out-of-tune engine or certain fuel or ignition malfu...

  • Page 305

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 306

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel filler cap. A poorly fitting cap could let impurities (continued) caution! (continued) into the fuel system. Also, a poorly fitting aftermar- ket cap can cause the “malfunction indicator light (m...

  • Page 307

    Warning! (continued) • a fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. Note: • when the fuel nozzle “clicks” or shuts off, the fuel tank is full. • tighten the gas cap about 1...

  • Page 308

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmission automatic transmission flat tow none transmission in neutral not allowed dolly tow front ok ok rear not allowed not allowed on trailer all ok ok this veh...

  • Page 309

    Caution! Towing this vehicle in violation of the above require- ments can cause severe transmission damage. Dam- age from improper towing is not covered under the new vehicle limited warranty. 5 starting and operating 307.

  • Page 311: Contents

    What to do in emergencies contents ! Hazard warning flashers . . . . . . . . . . .311 ! If your engine overheats . . . . . . . . . . . .311 ! Tire service kit — if equipped . . . . . . . . .312 ▫ tire service kit storage . . . . . . . . . . . . . . . . .313 ▫ tire service kit components and operatio...

  • Page 312

    ▫ jump-starting procedure . . . . . . . . . . . . . . . .340 ! Freeing a stuck vehicle . . . . . . . . . . . . .342 ! Shift lever override . . . . . . . . . . . . . . . .343 ! Towing a disabled vehicle . . . . . . . . . . .345 ▫ automatic transmission . . . . . . . . . . . . . . . . .346 ▫ manual tr...

  • Page 313

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the radio. Press the switch to turn on the hazard warning flashers. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Press th...

  • Page 314

    Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the n...

  • Page 315

    Tire service kit storage the tire service kit is located under the front driver’s seat. Tire service kit components and operation tire service kit location tire service kit components 1 — sealant bottle 5 — mode select knob 2 — deflation button 6 — sealant hose (clear) 3 — pressure gauge 7 — air pum...

  • Page 316

    Using the mode select knob and hoses your tire service kit is equipped with the following symbols to indicate the air or sealant mode. Selecting air mode push in the mode select knob (5) and turn to this position for air pump operation only. Use the black air pump hose (7) when selecting this mode. ...

  • Page 317

    • the sealant bottle (1) and sealant hose (6) are a one tire application use and need to be replaced after each use. Always replace these components immediately at your original equipment vehicle dealer. • when the tire service kit sealant is in a liquid form, clean water, and a damp cloth will remo...

  • Page 318

    Warning! • do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the tire service kit. • do not use tire service kit or drive the vehicle under the following circumstances: – if the puncture in the tire t...

  • Page 319

    Warning! (continued) • tire service kit sealant solution contains latex. In case of an allergic reaction or rash, consult a phy- sician immediately. Keep tire service kit out of reach of children. If swallowed, rinse mouth imme- diately with plenty of water and drink plenty of water. Do not induce v...

  • Page 320

    4. Remove the cap from the valve stem and then screw the fitting at the end of the sealant hose (6) onto the valve stem. 5. Uncoil the power plug (8) and insert the plug into the vehicle’s 12 volt power outlet. Note: do not remove foreign objects (e.G., screws or nails) from the tire. (c) injecting ...

  • Page 321

    Note: if the mode select knob (5) is on air mode and the pump is operating, air will dispense from the air pump hose (7) only, not the sealant hose (6). If the sealant (white fluid) does flow through the sealant hose (6): 1. Continue to operate the pump until sealant is no longer flowing through hos...

  • Page 322

    3. Immediately disconnect the sealant hose (6) from the valve stem, reinstall the cap on the fitting at the end of the hose, and place the tire service kit in the vehicle storage location. Quickly proceed to (d) “drive ve- hicle.” caution! • the metal end fitting from power plug (8) may get hot afte...

  • Page 323

    (e) after driving: pull over to a safe location. Refer to “whenever you stop to use tire service kit” before continuing. 1. Push in the mode select knob (5) and turn to the air mode position. 2. Uncoil the power plug and insert the plug into the vehicle’s 12 volt power outlet. 3. Uncoil the air pump...

  • Page 324

    5. Remove the speed limit sticker from the instrument panel after the tire has been repaired. 6. Replace the sealant bottle (1) and sealant hose (6) assembly at your authorized dealer as soon as pos- sible. Refer to (f) “sealant bottle and hose replace- ment”. Note: when having the tire serviced, ad...

  • Page 325

    Wheel and tire torque specifications proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any time a wheel has been removed and reinstalled on the vehicle the lug nuts/bolts should be torqued using a properly calibrated torque wrench. Torque speci...

  • Page 326

    Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten...

  • Page 327

    Warning! (continued) • being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be ra...

  • Page 328

    Spare tire removal the spare tire is stowed to the underbody below the cargo area. 1. Remove the plug located in the rear cargo area. 2. Fit the wrench tool over the drive nut. Use the wrench to rotate the nut counterclockwise until the spare is on the ground with enough slack in the cable to allow ...

  • Page 329

    Caution! The winch mechanism is designed for use with the jack wrench tool only. Use of an air wrench or other power tools is not recommended and they can damage the winch. 3. Pull the spare tire out from under the vehicle. Spare tire 6 what to do in emergencies 327.

  • Page 330

    4. Tilt the retainer at the end of the cable and pull it through the center of the wheel. Preparations for jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough...

  • Page 331

    5. Turn off the ignition. 6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. Note: passengers should not remain in the vehicle while the vehicle is being jacked. Jacking instructions war...

  • Page 332

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 333

    2. Remove center cap. Note: before using the swivel wrench to remove the wheel bolts be sure to remove the center cap of the wheel by inserting the angled tab end of the swivel wrench into the notched part of the center cap. 3. Loosen, but do not remove, the wheel bolts by turning them to the left o...

  • Page 334

    Do not raise the vehicle until you are sure the jack is securely engaged. 4. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to th...

  • Page 335

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Using the swivel wrench, raise the vehicle by turning the jack screw to the right. Raise the vehicle only unt...

  • Page 336

    7. Install the spare wheel and wheel bolts with the cone shaped end of the bolts toward the wheel. Lightly tighten the bolts. To avoid the risk of forcing the vehicle off the jack, do not tighten the bolts fully until the vehicle has been lowered. 8. Lower the vehicle by turning the jack screw to th...

  • Page 337

    Road tire installation vehicles equipped with wheel covers 1. Mount the road tire on the axle. 2. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand. Do not use a hammer or excessive force to install the cover. Tire and wheel cover or center cap 1 — ...

  • Page 338

    3. Install the four wheel bolts with the cone shaped end of the nut toward the wheel. Lightly tighten the wheel bolts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel bolts fully until the vehicle has been lowered. Failure to follow this warning may result in...

  • Page 339

    4. Finish tightening the wheel bolts. Push down on the wrench while at the end of the handle for increased leverage. Refer to “torque specifications” in this sec- tion for correct wheel bolt torque. 5. After 25 miles (40 km) check the wheel bolt torque with a torque wrench to ensure that all wheel b...

  • Page 340

    Warning! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Caution! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 volts or damage to the battery, starter motor, alternator or el...

  • Page 341

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 342

    Jump-starting procedure warning! Failure to follow this jump-starting procedure could result in personal injury or property damage due to battery explosion. Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Con...

  • Page 343

    5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. 6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the...

  • Page 344

    Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Then shift back and forth between drive and reverse (with automatic transmission) or 2nd gear an...

  • Page 345

    Caution! (continued) • revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h) while in gear (no trans- mission shifting occurring). Warning! Fast spinning tires can be dangerous....

  • Page 346

    4. Press and maintain firm pressure on the brake pedal. 5. Insert a small screwdriver or similar tool into the access hole, and push and hold the override release lever in. 6. Move the shift lever to the neutral position. 7. The vehicle may then be started in neutral. 8. Reinstall the shift lever ov...

  • Page 347

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial towing service. Towing condition wheels off the ground automatic transmission manual transmission flat tow none not allowed if transmission is operable: • transmission in neutral • 65 mph (10...

  • Page 348

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equipment manufacturer’s instructions. Use of safety chains is man- datory. Attach a tow bar or other towing device to main structural members ...

  • Page 349

    Caution! (continued) • towing this vehicle in violation of the above re- quirements can cause severe transmission damage. Damage from improper towing is not covered un- der the new vehicle limited warranty. Manual transmission • vehicle can be flat towed (all four wheels on the ground) with the tran...

  • Page 350

    • turn on the interior lights, which remain on as long as the battery has power or until the ignition key is removed. • unlock the doors automatically. After the event occurs, when the system is active, the message #fuel cutoff see handbook# is displayed. Carefully check the vehicle for fuel leaks i...

  • Page 351

    Customer action customer will see 5. Turn right turn signal switch on. Right turn light is on solid. Left turn light blinks. 6. Turn left turn signal switch on. Left turn light is on solid. Right turn light is on solid. 7. Turn left turn signal switch off. (turn signal switch must be placed in neutr...

  • Page 353: Maintaining Your Vehicle

    Maintaining your vehicle contents ! Engine compartment — 1.4l . . . . . . . . . .353 ! Engine compartment — 1.4l turbo . . . .354 ! Onboard diagnostic system — obd ii . .355 ! Emissions inspection and maintenance programs . . . . . . . . . . . . .356 ! Replacement parts . . . . . . . . . . . . . . ....

  • Page 354

    ▫ automatic transmission — if equipped . . . . .384 ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .386 ▫ convertible top care — if equipped . . . . . . .392 ! Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .394 ▫ interior fuses ....

  • Page 355

    Engine compartment — 1.4l 1 — engine coolant reservoir 5 — battery 2 — engine oil dipstick 6 — air cleaner filter 3 — brake fluid reservoir 7 — engine oil fill 4 — front distribution unit (fuses) 8 — washer fluid reservoir 7 maintaining your vehicle 353.

  • Page 356

    Engine compartment — 1.4l turbo 1 — engine coolant reservoir 5 — battery 2 — engine oil dipstick 6 — engine oil fill 3 — brake fluid reservoir 7 — washer fluid reservoir 4 — front distribution unit (fuses) 354 maintaining your vehicle.

  • Page 357

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 358

    Emissions inspection and maintenance programs in some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states that require an inspection and mainte- nance (i/m), this check verifies the...

  • Page 359

    • the mil will not flash at all and will remain fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is ready and you can proceed to the i/m station. If your obd ii system is not ready, you should see your authorized dealer or repair fac...

  • Page 360

    Note: intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. Warning! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If...

  • Page 361

    Engine oil checking oil level to assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed engine is shut off. Do ...

  • Page 362

    Engine oil selection — 1.4l engine for best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are api certified and meet the requirements of chrysler material standard ms-6395. Engine oil selection — 1.4l turbo engine for be...

  • Page 363

    Engine oil viscosity — 1.4l engine (sae grade) sae 5w-30 engine oil recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. You may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- me...

  • Page 364

    Synthetic engine oils you may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- mended maintenance intervals for oil and filter changes are followed. Materials added to engine oil the manufacturer strongly recommends against the addi- tion of any a...

  • Page 365

    Warning! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine comp...

  • Page 366

    Warning! (continued) • battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 volts. Do not allow cable clamps to touch each other. • battery posts, terminals, and related accessories...

  • Page 367

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at thi...

  • Page 368

    Refrigerant recovery and recycling r134a — if equipped r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) that is endorsed by the environmental protection agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by autho...

  • Page 369

    The a/c air filter is located in the fresh air inlet on the lower right of center console. Perform the following procedure to replace the filter: 1. Remove the torx® screw that secures the passenger side console closeout cover. 2. Pull the console closeout cover rearward to disengage the front retai...

  • Page 370

    3. Remove the two 5.5 mm screws (1 and 2) that secure the particulate air filter cover to the hvac housing. 4. Remove the a/c air filter by pulling it straight out of the housing. Take note of the air filter position indica- tors. 5. Install the a/c air filter with the air filter position indicators...

  • Page 371

    Caution! The a/c air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 6. Install the passenger side console closeout. Refer to the “maintenance schedule” for the proper mainte...

  • Page 372

    Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield or rear window. Avoid using the wiper blades to remove frost or ice from the windshield or rear window. Make s...

  • Page 373

    Note: the rear wiper arm cannot be raised fully up- ward unless the pivot cap is raised first. 2. Lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder. ...

  • Page 374

    4. Install the wiper blade pivot pin into the wiper blade holder at the end of the wiper arm, and firmly press the wiper blade until it snaps into place. 5. Lower the wiper blade and snap the pivot cap into place. Adding washer fluid the windshield washer fluid reservoir is located in the engine com...

  • Page 375

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips/exhaust gas” in “things to know before starting your vehicle” for further...

  • Page 376

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 377

    Cooling system warning! • when working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at any time the ignition switch is in the on position. • you or others can be badly burned by hot eng...

  • Page 378

    Cooling system — drain, flush and refill note: some vehicles require special tools to add coolant properly. Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system please contact your local authorized dealer. If the engin...

  • Page 379

    Caution! (continued) • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • this vehicle has not been designed for use with...

  • Page 380

    • use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain ...

  • Page 381

    Warning! • do not open hot engine cooling system. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap w...

  • Page 382

    Points to remember note: when the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment. This is nor- mally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vapor- ized when th...

  • Page 383

    Brake system in order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “maintenance schedule” for the proper maintenance intervals. Warning! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot rest...

  • Page 384

    Use only manufacturer’s recommended brake fluid. Re- fer to “fluids, lubricants, and genuine parts” in “main- taining your vehicle” for further information. Warning! • use only manufacturer’s recommended brake fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for ...

  • Page 385

    Warning! (continued) • do not allow petroleum-based fluid to contaminate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in a collision. Caution! Use of improper brake fluids will affect overall clutch system performance. Improper...

  • Page 386

    Frequency of fluid change under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless lubri- cant has become contaminated with water. Note: if contaminated with water, the fluid should be...

  • Page 387

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating cond...

  • Page 388

    Appearance care and protection from corrosion protection of body and paint from corrosion vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons a...

  • Page 389

    • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar® super kleen bug and tar remover to remove. • use a high quality cleaner wax, such as mopar® cleaner wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • av...

  • Page 390

    • if you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • if a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • use mopar® touch up paint on scratches as soon as possible. You...

  • Page 391

    Stain repel fabric cleaning procedure — if equipped stain repel seats may be cleaned in the following man- ner: • remove as much of the stain as possible by blotting with a clean, dry towel. • blot any remaining stain with a clean, damp towel. • for tough stains, apply mopar® total clean, or a mild ...

  • Page 392

    Warning! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Caution! Do not use alcohol and alcohol-based and/or keton based cleaning products to clean leather seats, as damage to the seat may result. Clean...

  • Page 393

    When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Instrument panel cover the instrument panel cover has a low glare surface which minimizes reflections on the windshield. Do not use protectants or other products whi...

  • Page 394

    Replace the belts if they appear frayed or worn or if the buckles do not work properly. Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immed...

  • Page 395

    Immediate removal of any contaminant is recommended. Regular washing of the top will enhance its life and appearance, and make successive cleanings easier. Do not subject the top to excessive heat. Frequently vacuum the top and storage compartment. Washing hand washing is highly recommended. Automat...

  • Page 396

    Scrub in all directions, covering an area of about two square feet at a time. Avoid heavy scrubbing. Rinse the entire vehicle with water to remove all soap and dirt from the top fabric and to prevent streaking on painted and chrome surfaces. Allow the top to dry before lowering. Vacuuming the top wi...

  • Page 397

    Warning! (continued) • if a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. Interior fuses the interior fuse panel is part of the body control module (bcm) and is l...

  • Page 398

    Cavity vehicle fuse number mini fuse description 3 f53 5 amp tan instrument panel node 4 f38 20 amp yellow central door locking 5 f36 10 amp red diagnostic socket, car radio, climate control system 6 f43 20 amp yellow bi-directional washer 7 f48 20 amp yellow passenger power window 8 f13 7.5 amp bro...

  • Page 399

    Underhood fuses the front distribution unit is located on the right side of the engine compartment, next to the battery. To access the fuses, press the release tabs and remove the cover. The id number of the electrical component correspond- ing to each fuse can be found on the back of the cover. Fro...

  • Page 400

    Cavity maxi fuse mini fuse description f01 60 amp blue – body controller f02 20 amp yellow – audio amplifier f03 20 amp yellow – ignition switch f04 40 amp orange – anti-lock brake pump f05 70 amp tan – electric power steering f06 20 amp yellow – radiator fan - single speed f06 30 amp green – radiat...

  • Page 401

    Cavity maxi fuse mini fuse description f16 – 7.5 amp brown transmission f17 – 25 amp clear powertrain (multiair – if equipped) f17 – 15 amp blue powertrain f18 – 15 amp blue powertrain f18 – 5 amp tan powertrain (multiair – if equipped) f19 – 7.5 amp brown air conditioning f20 – 15 amp blue heated s...

  • Page 402

    Cavity maxi fuse mini fuse description f85 30 amp green (ato) – rear defroster f87 – 5 amp tan rear defroster f90 – 5 amp tan heated mirrors – if equipped vehicle storage if you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • discon...

  • Page 403

    Replacement bulbs interior bulbs bulb number overhead lamp c5w courtesy lamp w5w exterior bulbs bulb number front low and high beam headlamp hir2ll front parking/daytime running lamps w21/5w front fog lamps h11ll front side marker lamps w3w front turn signal lamps wy21w side direction lamps wy5w rea...

  • Page 404

    Bulb number rear tail and stop lamps p21/5w rear backup lamps w16w center high mounted stop lamp w5w license plate lamps led (see authorized dealer) note: numbers refer to commercial bulb types that can be purchased from your authorized dealer. If a bulb needs to be replaced, visit your authorized d...

  • Page 405

    Front turn signal, parking and daytime running lamps 1. Turn the steering wheel completely to the left or right. 2. Open the wheel housing access door. 3. Remove the plastic cap from the back of the lamp housing. 4. Rotate bulb/socket counter-clockwise. 5. Remove the bulb and replace as needed. 6. I...

  • Page 406

    3. Pull the bulb from the socket and insert the replace- ment bulb. 4. Install the bulb and socket assembly into the housing, and rotate the socket clockwise to lock it in place. 5. Reinstall the wheel liner. Rear tail, stop, backup and turn signal lamps 1. Open the liftgate. 2. Remove the two screw...

  • Page 407

    4. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise. 5. Remove the backup lamp bulb by pulling straight out. 6. Replace lamps as required and reinstall lamp. Center high mounted stop lamp (chmsl) 1. Remove the two guard caps and the two fastening scr...

  • Page 408

    Fluid capacities u.S. Metric fuel (approximate) 10.5 gallons 40 liters engine oil with filter 1.4l/1.4l turbo engine 4 quarts 3.8 liters cooling system 1.4l/1.4l turbo engine (mopar® antifreeze/engine coolant 10 year/150,000 mile formula) — with manual transmission 4.6 quarts 4.4 liters 1.4l/1.4l tu...

  • Page 409

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant - 1.4l/1.4l turbo engine we recommend you use mopar® antifreeze/coolant 10 year/ 150,000 mile formula oat (organic additive technology) meeting the requirements of chrysler material standard ms-900...

  • Page 410

    Component fluid, lubricant, or genuine part fuel selection - 1.4l/1.4l turbo engine 87 octane acceptable — 91 octane recommended caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may ...

  • Page 411

    Chassis component fluid, lubricant, or genuine part manual transmission – if equipped we recommend you use mopar® c635 ddct/mtx transmission fluid automatic transmission – if equipped use only mopar® aw-1 automatic transmission fluid or equivalent. Failure to use the correct fluid may affect the fun...

  • Page 413: Maintenance Schedules

    Maintenance schedules contents ! Maintenance schedule . . . . . . . . . . . . .412 ▫ maintenance chart . . . . . . . . . . . . . . . . . . . .414 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 414

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 415

    Once a month or before a long trip: check engine oil level. Check windshield washer fluid level. Check the tire inflation pressures and look for unusual wear or damage. Check the fluid levels of the coolant reservoir and brake master cylinder, and fill as needed. Check function of all interior and e...

  • Page 416

    Maintenance chart refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 1...

  • Page 417

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 418

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 419

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 421: Contents

    If you need consumer assistance contents ! Suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .421 ▫ prepare for the appointment. . . . . . . . . . . . .421 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .421 ▫ be reasonable with requests ....

  • Page 422

    ! Department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .426 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .427 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .427 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .428 420 if...

  • Page 423

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 424

    Are most concerned that you get prompt and high quality service. The manufacturer’s authorized dealer have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an ...

  • Page 425

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 426

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You will be pleased with their sincere efforts to re...

  • Page 427

    Campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. To contact nhtsa, you may either call the auto safety hotline toll free at 1–888–327–4236 (tty: 1–800–424– 9153), or go to http://www.Safercar.Gov; or write to: admin- is...

  • Page 428

    Diagnostic procedure manuals diagnostic procedure manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and cor...

  • Page 429

    Treadwear the treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled condi- tions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100. The relat...

  • Page 430

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 431: Index

    Index 10

  • Page 432

    Adding engine coolant (antifreeze) . . . . . . . . . . . .377 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .303 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .372 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .301 air bag . . . . . . . . ....

  • Page 433

    Automatic transmission . . . . . . . . . . . . . . . . . . . .233 adding fluid . . . . . . . . . . . . . . . . . . . . . . . . . .385 fluid and filter changes . . . . . . . . . . . . . . . . . .385 fluid change . . . . . . . . . . . . . . . . . . . . . . . . . .385 fluid level check . . . . . . . . ...

  • Page 434

    Cellular phone . . . . . . . . . . . . . . . . . . . . . . . . . . .210 chains, tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . .286 change oil indicator . . . . . . . . . . . . . . . . . . . . . . .412 changing a flat tire . . . . . . . . . . . . . . . . . . . . . . .324 chart, tire si...

  • Page 435

    Coolant capacity . . . . . . . . . . . . . . . . . . . . . . .407 coolant level . . . . . . . . . . . . . . . . . . . . . . . . . .375 disposal of used coolant . . . . . . . . . . . . . . . . .379 drain, flush, and refill . . . . . . . . . . . . . . . . . . .376 inspection . . . . . . . . . . . . . ...

  • Page 436

    New trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165 start of trip procedure . . . . . . . . . . . . . . . . . . .166 trip computer . . . . . . . . . . . . . . . . . . . . . . . . .165 trip functions . . . . . . . . . . . . . . . . . . . . . . . . .166 emergency, in case of hazard w...

  • Page 437

    Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . .362 engine oil disposal . . . . . . . . . . . . . . . . . . . . .362 flashers turn signal . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 flooded engine starting . . . . . . . . . . . . . . . . . . . .229 fluid, brake . . . ...

  • Page 438

    General information . . . . . . . . . . . . . . . . . . . . . . .298 general maintenance. . . . . . . . . . . . . . . . . . . . . . .358 glass cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .390 hazard driving through flowing, rising, or shallow standing water . . . . . . . . . . . . ....

  • Page 439

    Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 key, sentry (immobilizer) . . . . . . . . . . . . . . . . . . . .13 lane change assist . . . . . . . . . . . . . . . . . . . . . . . .111 lap/shoulder belts. . . . . . . . . . . . . . . . . . . . . . . . .28 latches . . . ....

  • Page 440

    Locks automatic door . . . . . . . . . . . . . . . . . . . . . . . . .21 door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 power door . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 lubrication, body . . . . . . . . . . . . . . . . . . . . . . . . .369 lug nuts . . ....

  • Page 441

    Change interval . . . . . . . . . . . . . . . . . . . . . . . .359 checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .359 disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .362 filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .362 filter disposal ....

  • Page 442

    Rear liftgate (sedan) . . . . . . . . . . . . . . . . . . . . . . .24 rear window features . . . . . . . . . . . . . . . . . . . . .137 recorder, event data . . . . . . . . . . . . . . . . . . . . . . .54 recreational towing . . . . . . . . . . . . . . . . . . . . . . .306 reformulated gasoline . . ...

  • Page 443

    Child restraint . . . . . . . . . . . . . . . . . . . . . . . . . .55 extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 front seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 operating instruc...

  • Page 444

    Steering wheel audio controls . . . . . . . . . . . . . . .208 steering wheel mounted sound system controls . . .208 storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .400 storage, vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . .220 storing your vehicle . . . . . . . ...

  • Page 445

    Tire safety information . . . . . . . . . . . . . . . . . . . . .261 tire service kit . . . . . . . . . . . . . . . . . . . . . . . . . . .312 to open hood . . . . . . . . . . . . . . . . . . . . . . . . . . .106 towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .305 disabled vehi...

  • Page 446

    Washers, windshield . . . . . . . . . . . . . . . . . . . . . . .113 washing vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .386 water driving through . . . . . . . . . . . . . . . . . . . . . . . .245 wheel and wheel trim . . . . . . . . . . . . . . . . . . . . .388 wheel and wheel trim ...

  • Page 447

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 448

    Chrysler group llc o w n e r ’ s m a n u a l 2 0 1 5 2015 fia t 500 15ff500-126-ab second edition rev 1 printed in u.S.A. Fiat 500