1. DL manuals
  2. Fiat
  3. Automobile
  4. 2015 500 Abarth
  5. Owner's Manual

Fiat 2015 500 Abarth Owner's Manual

Summary of 2015 500 Abarth

  • Page 1

    Chrysler group llc o w n e r ’ s m a n u a l 2 0 1 5 2 0 1 5 f ia t 5 0 0 15ff500-126-aa first edition printed in u.S.A. Fiat 500

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understa...

  • Page 5: Introduction

    Introduction contents ! Introduction . . . . . . . . . . . . . . . . . . . . . . . .4 ! How to use this manual . . . . . . . . . . . . . .5 ! Warnings and cautions . . . . . . . . . . . . . .7 ! Vehicle identification number . . . . . . . .7 ! Vehicle modifications/alterations . . . .8 1.

  • Page 6

    Introduction congratulations on selecting your new vehicle. Be as- sured that it represents precision workmanship, distinc- tive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engineering spe...

  • Page 7

    How to use this manual consult the table of contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment. The detailed index ...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owners manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may miss importa...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped vin location 8 introduction.

  • Page 11: Contents

    Things to know before starting your vehicle contents ! A word about your keys . . . . . . . . . . . . .11 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .11 ▫ locking doors with a key. . . . . . . . . . . . . . . .13 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .13 ! Sentry k...

  • Page 12

    ▫ auto door locks . . . . . . . . . . . . . . . . . . . . . .23 ! Power windows . . . . . . . . . . . . . . . . . . . . .24 ▫ power window switches . . . . . . . . . . . . . . . . .24 ▫ auto-down . . . . . . . . . . . . . . . . . . . . . . . . . .25 ▫ wind buffeting . . . . . . . . . . . . . . . . ....

  • Page 13

    A word about your keys the key fob contains the remote keyless entry (rke) transmitter with an integrated key. To use the mechanical key, simply push the mechanical key release button. The vehicle is supplied with a code card containing key code numbers to order duplicate keys, and the autho- rized ...

  • Page 14

    Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park and re- move the key fob from the vehicle. When leaving the vehicle, always lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children t...

  • Page 15

    Warning! (continued) • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Caution! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unatt...

  • Page 16

    Note: a key which has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle. If the vehicle security light is on after the key is turned to the on/run position, it indicates that there is a problem with the electronics. Cau...

  • Page 17

    • this device must accept any interference that may be received, including interference that may cause unde- sired operation. Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Remote keyless entry (...

  • Page 18

    To unlock the doors and liftgate push and release the unlock button on the rke transmitter once to unlock the driver’s door or twice, within five seconds, to unlock all doors and the liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also ...

  • Page 19

    Open/close power top remote function — if equipped: 1. Open — push and hold the unlock button down to cycle the convertible top to the desired partial/full open position. 2. Close — push and hold the lock button down to cycle the convertible top to the desired partial/full closed position. Warning! ...

  • Page 20

    To lock the doors and liftgate push and release the lock button on the rke transmit- ter to lock all doors and the liftgate. The turn signal lights will flash and the horn will chirp to acknowledge the signal. Programming additional transmitters refer to sentry key® “customer key programming.” if yo...

  • Page 21

    3. Take out the battery case. Remove and replace the battery observing its polarity. 4. Refit the battery case inside the key fob and turn the screw to lock it into place. Key fob screw location battery case removed 2 things to know before starting your vehicle 19.

  • Page 22

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 23

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. (continued) warning! (continued) • for personal security and safety in the event of a collision, lock the vehicle doors as you drive as well as when you park a...

  • Page 24

    Warning! (continued) • do not leave the key fob in or near the vehicle, or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle. Caution! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of...

  • Page 25

    Auto door locks when enabled, the door locks will lock automatically when the vehicles speed exceeds 15 mph (24 km/h). To change the setting proceed as follows: 1. Briefly push the menu button to enter the menu screen. 2. Push the up or down button to highlight “auto door locks”. Push the menu butto...

  • Page 26

    Power windows power window switches there are single window controls located on the shifter bezel, below the climate controls, which operate the driver and passenger door windows. The window con- trols will operate when the ignition switch is in the on/run position. Warning! Never leave children una...

  • Page 27

    Auto-down the driver’s door window switch has an auto-down feature. Push the window switch for approximately one second, release, and the window will go down automati- cally. To cancel the auto-down movement, operate the switch in either the up or down direction and release the switch. Wind buffetin...

  • Page 28

    Warning! • driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • if you are required to drive with the liftgate open, make sure that all windows are c...

  • Page 29

    Occupant restraint systems some of the most important safety features in your vehicle are the restraint systems: • seat belt systems • supplemental restraint systems (srs) air bags • child restraints important safety precautions please pay close attention to the information in this section. It tells...

  • Page 30

    6. All occupants should always wear their lap and shoulder belts properly. 7. The driver and front passenger seats should be moved back as far as practical to allow the advanced front air bags room to inflate. 8. Do not lean against the door or window. If your vehicle has side air bags, and deployme...

  • Page 31

    Ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Enhanced seat belt use reminder system (beltalert) beltalert is a feature intended to remind the driver and outboard front passenger (if equipped with out- board f...

  • Page 32

    Note: if beltalert has been deactivated, the seat belt reminder light will continue to illuminate while the driver’s or outboard front passenger’s (if equipped with beltalert) seat belt remains unbuckled. Lap/shoulder belts all seating positions in your vehicle are equipped with lap/shoulder belts. ...

  • Page 33

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. • wearing your seat belt incorrectly could make your injuries in a collision much worse. You ...

  • Page 34

    Warning! (continued) • a seat belt that is too loose will not protect you properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • a seat belt that is worn under your arm is danger- ous. Your body could strike the inside surfaces...

  • Page 35

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat). Grasp the latch plate and pull out the sea...

  • Page 36

    4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug seat belt reduces the risk of sliding...

  • Page 37

    6. To release the seat belt, push the red button on the buckle. The seat belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the seat belt to retract fully. Lap/shoulder belt untwisting procedure use the following procedure to untwist...

  • Page 38

    Warning! • only use a seat belt extender if it is physically required in order to properly fit the original seat belt system. Do not use the seat belt extender if, when worn, the distance between the front edge of the seat belt extender buckle and the center of the occupant’s body is less than 6 inc...

  • Page 39

    Note: these devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. The pretensioners are triggered by the occupant re- straint controller (orc). Like the air bags, the preten- sioners are single use items. A deplo...

  • Page 40

    • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol driver center passenger first row n/a n/a alr second row alr n/a alr • n/a — not applicable • alr — automatic locking retractor if the passenger seating position is equipped with an alr and is being used for nor...

  • Page 41

    In automatic locking mode, the shoulder belt is auto- matically pre locked. The seat belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is available on all passenger seating positions with a combination lap/shoulder belt. Use the automatic locking mode anyti...

  • Page 42

    Warning! • the seat belt assembly must be replaced if the switchable automatic locking retractor (alr) fea- ture or any other seat belt function is not working properly when checked according to the proce- dures in the service manual. • failure to replace the seat belt assembly could increase the ri...

  • Page 43

    • seat belt pretenioners • seat belt buckle switch • seat track position sensors advanced front air bags this vehicle has advanced front air bags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s advanced front air bag is mounted in the center o...

  • Page 44

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 45

    The driver or front passenger seat belt is buckled. The seat belt buckle switch may adjust the inflation rate of the advanced front air bags. Warning! • no objects should be placed over or near the air bag on the instrument panel or steering wheel, because any such objects could cause harm if the ve...

  • Page 46

    On the other hand, depending on the type and location of impact, advanced front air bags may deploy in crashes with little vehicle front-end damage but that produce a severe initial deceleration. Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves a...

  • Page 47

    Supplemental driver knee air bag this vehicle is equipped with a supplemental driver knee air bag mounted in the instrument panel below the steering column. The supplemental driver knee air bag provides en- hanced protection during a frontal impact by working together with the seat belts, pretension...

  • Page 48

    When the sab deploys, it opens the seam on the out- board side of the seatback’s trim cover. The inflating sab deploys through the seat seam into the space between the occupant and the door. The sab moves at a very high speed and with such a high force that it could injure you if you are not seated ...

  • Page 49

    The sabic deploys downward, covering the side win- dows. An inflating sabic pushes the outside edge of the headliner out of the way and covers the window. The sabics inflate with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the sa...

  • Page 50

    The sabics and sabs (“side air bags”) are designed to activate in certain side impacts. The occupant restraint controller (“orc”) determines whether the deployment of the side air bags in a particular impact event is appropri- ate, based on the severity and type of collision. The side impact sensors...

  • Page 51

    Be properly restrained in a child restraint or booster seat that is appropriate for the size of the child. Warning! • side air bags need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. • being too close to the side air bags during deploy- ment could ca...

  • Page 52

    • as the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the are...

  • Page 53

    Enhanced accident response system in the event of an impact, if the communication network remains intact, and the power remains intact, depending on the nature of the event, the orc will determine whether to have the enhanced accident response sys- tem perform the following functions: • cut off fuel...

  • Page 54

    Customer action customer will see 1. Turn ignition off. (turn signal switch must be placed in neutral state). 2. Turn ignition on. Left turn light is off. Right turn light blinks. 3. Turn right turn signal switch on. Right turn light is on solid. Left turn light blinks. 4. Turn left turn signal swit...

  • Page 55

    If a reset procedure step is not completed within 45 seconds, then the turn signal lights will turn off and the reset procedure must be performed again in order to be successful. Air bag warning light the air bags must be ready to inflate for your protection in a collision. The occupant re- straint ...

  • Page 56

    Free, if any of the following occurs, have an authorized dealer service the air bag system immediately. • the air bag warning light does not come on during the four to eight seconds when the ignition is first placed in the on/run position. • the air bag warning light remains on after the four to eig...

  • Page 57

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 58

    Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The main purpose of an edr is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per-...

  • Page 59

    Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the united states, and every canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be pros- ecuted for ignoring it. Ch...

  • Page 60

    Note: • for additional information, refer to www.Seatcheck.Org or call 1–866–seatcheck (732–8243). Canadian resi- dents should refer to transport canada’s website for additional information: • www.Tc.Gc.Ca/eng/roadsafety/safedrivers- childsafety-index-53.Htm summary of recommendations for restrainin...

  • Page 61

    Child size, height, weight or age recommended type of child restraint larger children children who have out-grown their forward-facing child restraint, but are too small to properly fit the vehicle’s seat belt belt positioning booster seat and the vehicle seat belt, seated in the rear seat of the ve...

  • Page 62

    Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint. • only use a rear-facing child restraint in a vehicle with ...

  • Page 63

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • after a child restraint i...

  • Page 64

    2. Do the child’s knees bend comfortably over the front of the vehicle seat – while they are still sitting all the way back? 3. Does the shoulder belt cross the child’s shoulder between their neck and arm? 4. Is the lap part of the seat belt as low as possible, touching the child’s thighs and not th...

  • Page 65

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 66

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 67

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 2 things to know before starting your vehicle 65.

  • Page 68

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and teth...

  • Page 69

    Can the rear-facing child restraint touch the back of the front passenger seat? Yes the child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint owner’s manual for more information. Can the head restraints be removed?...

  • Page 70

    Locating tether anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower ancho...

  • Page 71

    1. Loosen the adjusters on the lower straps and on the tether strap of the child seat so that you can more easily attach the hooks or connectors to the vehicle anchorages. 2. Place the child seat between the lower anchorages for that seating position. For some second row seats, you may need to recli...

  • Page 72

    How to stow an unused alr seat belt: when using the latch attaching system to install a child restraint, stow all alr seat belts that are not being used by other occupants or being used to secure child restraints. An unused belt could injure a child if they play with it and accidentally lock the sea...

  • Page 73

    Installing child restraints using the vehicle seat belt the seat belts in the passenger seating positions are equipped with a switchable automatic locking retractor (alr) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a l...

  • Page 74

    What is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a for- ward facing child restrai...

  • Page 75

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 76

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the seat belt path. It should not move more than 1 inch (25.4 mm) in any ...

  • Page 77

    Tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available. 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints...

  • Page 78

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 79

    Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem. Safety tip...

  • Page 80

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 81

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 82

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 83

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 85: Contents

    Understanding the features of your vehicle contents ! Power convertible top — if equipped . .86 ▫ lowering the power top. . . . . . . . . . . . . . . . .86 ▫ raising the power top . . . . . . . . . . . . . . . . . .86 ▫ power convertible top relearn procedure . . . . .88 ▫ wind stop . . . . . . . . ...

  • Page 86

    ▫ seat height adjustment . . . . . . . . . . . . . . . . .103 ▫ ez entry feature . . . . . . . . . . . . . . . . . . . . . .103 ▫ memory feature . . . . . . . . . . . . . . . . . . . . . .104 ▫ heated seats — if equipped . . . . . . . . . . . . .104 ▫ head restraints . . . . . . . . . . . . . . . . ...

  • Page 87

    ▫ to resume speed . . . . . . . . . . . . . . . . . . . . .121 ▫ to vary the speed setting . . . . . . . . . . . . . . .121 ▫ to accelerate for passing . . . . . . . . . . . . . . . .122 ! Rear park assist — if equipped . . . . . . . .123 ▫ rear park assist sensors . . . . . . . . . . . . . . . .123...

  • Page 88

    Power convertible top — if equipped on vehicles equipped with a power convertible top, the power convertible top switch is located on the overhead console. The switch contains two buttons. The passenger side button, is used to open the power top, and the driver side button, is used to close the powe...

  • Page 89

    Approximately one second a second time for the one- quarter open position. Push and hold close button to fully close convertible top. Note: rail lubrication is recommended every 2000 cycles, or if scratching noises due to dust are present. Refer to “fluids, lubes, and genuine part” in “maintain- ing...

  • Page 90

    Power convertible top relearn procedure if your power convertible top does not operate in the auto opening/closing mode (automatically opening/ closing to the one-quarter open and three-quarter open comfort stops), or if the trunk lid does not open - the following relearn procedure may be necessary....

  • Page 91

    Wind stop the wind stop installs in the backseat area of the vehicle. The wind stop will not interfere with power top opera- tion. Therefore, it can remain installed when the top is up. Mirrors inside day/night mirror the mirror can be adjusted up, down, left, and right for various drivers. The mirr...

  • Page 92

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pushing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activat...

  • Page 93

    Power mirrors the power mirror controls are located on the driver’s door trim panel. The power mirror controls consist of a mirror select switch and a four-way mirror control switch. To adjust a mirror, push the mirror select switch to either the l (left) or r (right) to select the mirror you need t...

  • Page 94

    Spotter mirror — if equipped some models are equipped with a driver’s side spotter mirror. The spotter mirror allows for a greater range of visibility on the driver’s side of the vehicle. Folding mirrors the exterior mirrors are hinged to allow the mirror to pivot forward or rearward to help avoid d...

  • Page 95

    Blue&me™ hands-free communication blue&me™ hands-free communication overview — if equipped windows mobile™-based fiat blue&me™ is a per- sonal telematic system enabling you to use communica- tion and entertainment applications expressly designed for use in the car. The blue&me™ system installed on y...

  • Page 96

    You are not required to train the voice recognition system to recognize your voice. This implies that the system is nearly equally performing with different persons, i.E.: the voice recognition system is of the “speaker independent” type. With this system you can also play your favorite music stored...

  • Page 97

    Steering wheel controls and the instrument panel multi- function display. Please refer to the fiat blue & me radio supplement for further information. To get started with blue&me™ hands-free kit with voice recognition, you have to simply pair your bluetooth® wireless technology enabled mobile phone ...

  • Page 98

    • to interact with blue&me™ you can use either the buttons on the steering wheel or voice commands. With voice recognition, you can perform system func- tions by speaking voice commands, also identified as “keywords”. When the system recognizes a keyword, it will respond with the appropriate action....

  • Page 99

    • conference call — you can call another contact while you are engaged in a phone conversation (with bluetooth® phones supporting this option). • call waiting — while engaged in a phone conversa- tion, you can receive notification of another incoming phone call, answer the other incoming phone call,...

  • Page 100

    Message reader functions are managed by the control buttons on the steering wheel or by the blue&me™ voice commands. The blue&me™ message reader enables the following operations: • to display an indicator on the instrument panel that indicates you have received a new sms text. It will display the se...

  • Page 101

    • ipod® player — see dedicated paragraph under me- dia player functions. The media player enables the following operations: • digital audio playback — you can play all your digital audio files (.Mp3, .Wma, .Wav, .Aac) or play a customized playlist (.M3u or .Wpl format). • audio file selection by cat...

  • Page 102

    Warning! • driving while distracted can result in loss of ve- hicle control, accident and injury. It is strongly recommended that you use extreme caution when using any device or feature that may take your focus off the road or your hands off the steering wheel. Your primary responsibility is the sa...

  • Page 103

    Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision...

  • Page 104

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 105

    Seat height adjustment the driver’s seat height can be raised or lowered by using a lever, located on the outboard side of the seat. Pump the lever upward to raise the seat height, or pump the lever downward to lower the seat height. Ez entry feature the driver and front passenger seats have an ez e...

  • Page 106

    Lift the seatback upright and push the seat rearward to its locked position once the rear passengers are seated. Memory feature both front seats have a memory feature, which can operate in two ways: memory function option 1 — full seat back and track fore/aft position memory: after using the ez entr...

  • Page 107

    Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially ...

  • Page 108

    Reactive head restraints — front seats the front driver and passenger seats are equipped with reactive head restraints. In the event of a rear impact the reactive head restraints will automatically extend forward minimizing the gap between the back of the occupant’s head and the reactive head restra...

  • Page 109

    Note: the head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealership. Warning! Do not place items over the top of the reactive head restraint, such as coats, seat covers or portable dv...

  • Page 110

    To open and close the hood to open the hood, two latches must be released. 1. Pull the bottom of the red hood release lever, located on the left kick panel, rearward. 2. Rotate the safety catch under the front edge of the hood, near the center, and raise the hood. 3. Lift the hood prop rod that clip...

  • Page 111

    In hot climates, the prop rod may be hot. Pick up the prop rod at the foam on the end of the prop rod. Caution! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 6 inches (15 cm), and then drop it. This should secure both latches. Never dri...

  • Page 112

    Lights multifunction lever the multifunction lever, located on the left side of the steering wheel, controls the operation of the headlights, headlight beam selection, passing light and turn signals. Note: the external lights can only be turned on with the ignition in the on/run position. Headlights...

  • Page 113

    High beams with the low beams activated, push the multi- function lever towards the instrument panel to turn on the high beams. Pull the multifunction lever toward the steering wheel to turn off the high beams. Flash-to-pass you can signal another vehicle with your headlights by partially pulling th...

  • Page 114

    Note: the indicators will automatically turn off when the turn has been completed and the steering wheel is returned to a straight position. Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatical...

  • Page 115

    Deactivation pull the multifunction lever toward the steering wheel and hold it for more than two seconds. Interior lights the interior light switches are located in the overhead console. The interior lights can be set to three different positions (off/left position, center position, on/right positi...

  • Page 116

    • when the doors are locked with the key fob the lights will turn off. Interior light timing (on/right position) • when all doors are closed a 15 minute timer is activated. Note: the timer is deactivated when the key is moved into the on/run position. Front fog lights — if equipped the fog light swi...

  • Page 117

    Windshield wipers and washers the windshield wiper/washer lever is located on the right side of the steering column. Note: the windshield wipers/washers will only oper- ate with the ignition in the on/run position. Front windshield wiper operation there are five different modes of operation for the ...

  • Page 118

    Note: the intermittent function only has one detent but wiper delay will vary with changes in vehicle speed. As vehicle speed increases the delay time will decrease. Low speed push the lever downward to the second detent. The wipers will operate at low speed. High speed push the lever downward to th...

  • Page 119

    Caution! (continued) • always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper control is turned off and the blades cannot return to the off position, damage to the wiper motor may occur. Rear windshield wiper rotate the...

  • Page 120

    Rear windshield washer operation push the windshield wiper/washer lever toward the instrument panel to activate the rear washer. Push and hold the lever for more than a half second and the wipers will activate automatically for three cycles after the lever is released. Tilt steering column — if equi...

  • Page 121

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Electronic speed control ...

  • Page 122

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 123

    To deactivate a soft tap on the brake pedal, pushing the canc button, or normal brake pressure while slowing the vehicle will deactivate electronic speed control without erasing the set speed memory. Pushing the on/off button or turning the ignition switch off erases the set speed in memory. To resu...

  • Page 124

    To decrease speed when the electronic speed control is set, you can de- crease speed by pushing the set (-) button. The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “ under- standing your instrument panel” for more information. The speed decreme...

  • Page 125

    On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without electronic speed control. Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose cont...

  • Page 126

    Rear park assist warning display the rear park assist warning screen is located within the electronic vehicle information center (evic). It provides audible and visual warnings to indicate the distance between the rear fascia/bumper and the detected ob- stacle. Refer to #electronic vehicle informati...

  • Page 127

    Audible and visual signals supplied by the rear park assist system signal meaning indication obstacle distance an obstacle is present within the sensors’ field of view audible signal (dashboard loudspeaker) • sound pulses emitted at a rate that in- creases as the distance decreases. • emits continuo...

  • Page 128

    Signal meaning indication failure sensor or system failures visual signal (instrument panel) • icon appears on display. • message is displayed on the electronic vehicle information center (evic) (where provided). While audible signals are emitted, the audio system is not muted. The audible signal is...

  • Page 129

    The sensors and wiring are tested continuously when the ignition is in the on/run position. Failures are indi- cated immediately if they occur when the system is on. Even if the system is able to identify that a specific sensor is in failure condition, the evic shall indicate that the rear park assi...

  • Page 130

    • objects such as bicycle carriers, etc., must not be placed within 12 in (30 cm) from the rear fascia/ bumper while driving the vehicle. Failure to do so can result in the system misinterpreting a close object as a sensor problem, causing a failure indication to be displayed in the instrument clust...

  • Page 131

    Warning! • drivers must be careful when backing up even when using the rear park assist system. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety ...

  • Page 132

    Power sunroof — if equipped the power sunroof roof switch is located in the overhead console. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location acces- sible to children. Occupants, particularly ...

  • Page 133

    To open push and hold the power sunroof switch rearward for approximately one second and the sunroof will stop at the vented position. Push the switch a second time and hold for approximately one second and release, the sunroof will open fully, then stop automatically. This is called “express open”....

  • Page 134

    Emergency operation in case of electrical failure the sunroof can be operated with the hex wrench that is located in the glove box. There is a plug located in the rear of the sunroof opening at the center of the vehicle. Removing the plug reveals a hex opening in the motor assembly of the sunroof. I...

  • Page 135

    Electrical power outlets there is a standard 12 volt (13 amp) power outlet, located in the floor console, for added convenience. This power outlet can power mobile phones, electronics and other low power devices. Power is available when the ignition switch is in the on/run or start position. Insert ...

  • Page 136

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 137

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 138

    For rear passengers, there are cupholders located on the floor between the front driver and passenger seats. Front cupholders rear cupholders 136 understanding the features of your vehicle.

  • Page 139

    Storage glove compartment the glove compartment is located on the right side of the instrument panel. Pull outward on the glove compart- ment latch to open the glove compartment. Push the glove compartment door upward to close it. Glove compartment latch 3 understanding the features of your vehicle ...

  • Page 140

    Cargo area features the rear seatbacks have a fold down feature to allow increased cargo capacity. Push down the release button, located at the outboard top of the seatback and move the seatback to its folded- down position to provide a flat load floor cargo area. When returning the seatback to its ...

  • Page 141

    Rear window features rear window defroster the rear window defroster button is located in the center of the instrument panel, below the radio. Push this button to turn on the rear window defroster. An indicator in the instrument cluster will illuminate when the rear window defroster is on. The rear ...

  • Page 142

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 143: Contents

    Understanding your instrument panel contents ! Instrument panel features . . . . . . . . . .143 ! Instrument cluster . . . . . . . . . . . . . . . . .144 ! Instrument cluster — eco . . . . . . . . . . .145 ! Instrument cluster — pop, lounge, 500c . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 144

    ▫ introduction . . . . . . . . . . . . . . . . . . . . . . . . .180 ▫ suggestions. . . . . . . . . . . . . . . . . . . . . . . . . .181 ▫ technical specifications . . . . . . . . . . . . . . . . .183 ▫ quick guide . . . . . . . . . . . . . . . . . . . . . . . . .184 ▫ general information. . . . . . ...

  • Page 145

    Instrument panel features 1 — side vent 7 — passenger air bag 13 — storage compartment 2 — multifunction lever – light control 8 — glove compartment 14 — shift lever 3 — instrument cluster and warning lights 9 — rear defrost button 15 — sport button 4 — windshield wiper, washer, trip computer 10 — h...

  • Page 146

    Instrument cluster 144 understanding your instrument panel.

  • Page 147

    Instrument cluster — eco 4 understanding your instrument panel 145.

  • Page 148

    Instrument cluster — pop, lounge, 500c 146 understanding your instrument panel.

  • Page 149

    Instrument cluster descriptions 1. Tire pressure monitoring telltale light — if equipped each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure ...

  • Page 150

    As intended. Tpms malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the tpms from functioning properly. Always check the tpms malfunction telltale after replacing one or more tires or wheels on your veh...

  • Page 151

    Note: • a continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on. • check for an inoperative outside light bulb if either indicator remains on and does not flash, or flashes at a rapid rate. 4. Electronic stability control (esc) activation/ malfunct...

  • Page 152

    5. Air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to on/run. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible. Re...

  • Page 153

    9. Malfunction indicator light (mil) the malfunction indicator light (mil) is part of an onboard diagnostic (obdii) system which monitors the emissions and engine con- trol system. If the vehicle is ready for emissions testing, the light will come on when the ignition is first turned on and remain o...

  • Page 154

    Warning! (continued) drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants or others. 10. Front fog light indicator — if equipped this indicator will illuminate when the front fog lights are on. ...

  • Page 155

    14. Brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system...

  • Page 156

    Warning! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. Vehicles equipped with the abs, are also equipped with electronic brake force dist...

  • Page 157

    Brakes. If the abs light does not turn on when the ignition switch is turned to the on/run position, have the light inspected by an authorized dealer. 16. Gas pedal percentage gauge/turbo gauge/eco in- dex gauge depending on what options and trim level, your vehicle is equipped with there are three ...

  • Page 158

    18. Electronic vehicle information center (evic) the evic features a driver-interactive display that is located in the instrument cluster. For further information, refer to “electronic vehicle information center (evic)” in “understanding your instrument panel.” 19. Temperature gauge the temperature ...

  • Page 159

    Warning! (continued) vehicle.” follow the warnings under the “cooling system pressure cap” paragraph. 20. Tachometer the tachometer indicates engine speed in revolutions per minute (rpm x 1000). 21. Speedometer / trip odometer / electronic vehicle information center (evic) display area this display ...

  • Page 160

    23. Generic warning light the generic warning light will illuminate if any of the following conditions occur: oil change request, engine oil pressure sensor failure, external light failure, fuel cut-off intervention, fuel cut-off not available, parking sensor failure. 24. Cruise on indicator — if eq...

  • Page 161

    The light is flashing when the engine is running, imme- diate service is required and you may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. The light will come on when the ignition is first turned to on/run and remain on briefly as a bulb...

  • Page 162

    The evic consists of the following: • system status • vehicle information warning message displays • personal settings (customer-programmable features) • outside temperature display • trip computer functions • tire pressure monitoring display electronic vehicle information center (evic) display 160 ...

  • Page 163

    Evic displays 1. Red telltales (left bank) • hood ajar • low oil pressure • electronic throttle control • door ajar • speed limiter — if equipped 2. Amber telltales • ice risk • fuel cut off • fuel cut off failed • hill holder failed • oil change request • check lights • vehicle lock 3. Electronic s...

  • Page 164

    5. Red telltales (right bank) • trunk ajar • transmission failure • battery charge indicator 6. Exceeded speed limiter 7. Shift up or down indicators 8. Gear indicator evic control buttons push and release the menu button briefly to access the evic. Push and hold the menu button (approximately one s...

  • Page 165

    Electronic vehicle information center (evic) setup menu the menu comprises a series of functions arranged in a cycle. Push and release the up and down but- tons to access the different options and settings (setup). The setup menu can be activated by pushing the menu button. A single push on the up o...

  • Page 166

    Selecting an option of the main menu without submenu 1. Briefly push and release the menu button to select the main menu option to set. 2. Push and release the up or down button (by single pushes) to select the new setting. 3. Briefly push and release the menu button to store the new setting and go ...

  • Page 167

    Change engine oil indicator system change engine oil your vehicle is equipped with an engine oil change indicator system. The “change engine oil” message will flash in the evic display for approximately 10 seconds after a single chime has sounded to indicate the next scheduled oil change interval. T...

  • Page 168

    Trip button the trip button, located on the right steering column stalk, can be used to display and to reset the previously described values. • a short button push displays the different values. • a long button push resets the system and then starts a new trip. New trip to reset: • push and hold the...

  • Page 169

    Trip functions both trip functions are resettable (reset — start of new trip). “trip a” can be used to display the figures relating to: • range • trip distance a • average consumption • instantaneous consumption • average speed a • travel time a (driving time) “trip b” can be used to display the fig...

  • Page 170

    Note: the range depends on several factors: driving style, type of route (freeway, residential, mountain roads, etc.), conditions of use of the car (load, tire pressure, etc.). Trip planning must take into account the above notes. Distance traveled this value shows the distance covered since the las...

  • Page 171

    2. Briefly push and release the menu button to go back to the menu screen or push and hold the menu (approximately one second) to go back to the main screen without storing settings. Speed beep (speed limit) with this function, it is possible to set the car speed limit (mph or km/h) to immediately a...

  • Page 172

    To cancel the setting, proceed as follows: 1. Briefly push and release the menu button. “on” will flash on the display. 2. Push and release the down button. “off” will flash on the display. 3. Briefly push and release the menu button to go back to the menu screen, or push and hold the menu button (a...

  • Page 173

    2. Push and release the up or down button to navigate the two sub-menu items. 3. Select the required option and then push and release the menu button. 4. When accessing the “time” sub-menu item, briefly push and release the menu button and “hours” will flash on the display. 5. Push and release the u...

  • Page 174

    Menu button (approximately one second) to go back to the main screen without storing the settings. Set date this function may be used to set the date (day - month - year). To change, the date proceed as follows: 1. Briefly push and release the menu button. Push and release the up or down button to h...

  • Page 175

    See radio (repeat audio information) with this function active, the evic display shows infor- mation relevant to the sound system. • radio: tuned radio station frequency, automatic tuning activation or autostore. • cd audio, cd mp3: track number. To activate (on) or to deactivate (off) the sound sys...

  • Page 176

    2. Push and release the up or down button to select display deactivation “off”, “mph” or “km/h.” 3. Briefly push and release the menu button to go back to the menu screen, or push and hold the menu button (approximately one second) to go back to the main screen. Autoclose with this function active, ...

  • Page 177

    2. Push and release the up or down button to navigate the three sub-menus. 3. Select the required sub-menu and then briefly push and release the menu button. 4. When accessing the “distance” submenu, briefly push and release the menu button. Either “mi” or “km” will appear on the display (according ...

  • Page 178

    When you have made the required settings, briefly push and release the menu button to go back to the sub-menu screen, or push and hold the menu button (approxi- mately one second) to go back to the main screen without storing the settings. Language (selecting the language) the messages can be displa...

  • Page 179

    3. Briefly push and release the menu button to go back to the menu screen, or push and hold the menu button (approximately one second) to go back to the main screen without storing the settings. Button volume (button volume adjustment) this function may be used to adjust the volume of the beep accom...

  • Page 180

    2. Briefly push and release the menu button. “on” or “off” will flash on the display (according to previous setting). 3. Push and release the up or down button for setting. 4. Briefly push and release the menu button to go back to the menu screen, or push and hold the button (approximately one secon...

  • Page 181

    Hill start assist this function is used when starting a vehicle from a stop on a hill. Hill start assist maintains the same level of brake pressure the driver applied for a short period of time after the foot has been removed from the brake pedal. Proceed as follows to switch this function on or off...

  • Page 182

    Lock when unlock driver door is selected, only the driver’s door will unlock on the first push of the remote keyless entry (rke) transmitter unlock button. When unlock drivers door is selected, you must push the rke transmit- ter unlock button twice to unlock the passenger door. When all doors is se...

  • Page 183

    If the radio has blue&me™, refer to the appropriate “blue&me™ user’s manual” for further information. The instructions for use are given below and we recom- mend you to read them carefully. Suggestions road safety please, learn how to use all different radio functions (e.G. Store stations) before be...

  • Page 184

    • clean every cd thoroughly removing any finger marks or dust using a soft cloth. Hold cds by the outside and clean them from the middle outwards. • never use chemicals (e.G. Antistatics or thinners or sprays) for cleaning as they could damage the surface of the cds. • after listening to them place ...

  • Page 185

    • the cd player is capable of reading most compression systems currently in use, following the development of these systems, the reading of all compression formats is not guaranteed. Technical specifications the complete system consists of: • two 165 mm diameter midwoofer speakers, one speaker in ea...

  • Page 186

    Quick guide radio controls button general functions mode on short button push off short button push tuner am, fm, sat (if equipped) source selection short repeated button push a-b-c cycles a, b, c presets for am, fm, sat (if equipped) short repeated button push media cd/aux/media player (if equipped...

  • Page 187

    Button general functions mode (mute/pause button) volume activation/deactivation (mute/pause) short button push audio audio adjustments: low tones (bass), high tones (treble), left/ right balance (balance), front/ rear balance (fader) menu activation: short button push adjustment type selection: pus...

  • Page 188

    Button radio functions mode radio station search: • automatic search • manual search automatic search: push buttons or (long push for fast for- ward) manual search: push buttons or (long push for fast forward) 1 2 3 4 5 current radio station storing long button push for memory pre- set 1 to 5 respec...

  • Page 189

    General information the radio offers the following functions: radio section • pll tuning with fm/am bands • rbds (radio broadcast data system) • automatic/manual station tuning • fm multipath detector • manual storing of 25 stations (base radio) and 40 stations (if equipped with satellite): 15 on fm...

  • Page 190

    • track selection (forward/backward) • fast forward/rewind through tracks • mp3 display function: display of folder name, id3- tag information, time elapsed since the start of the track, name of the file • playing audio or data cd, cd-r and cd-rw audio section • mute/pause function • soft mute funct...

  • Page 191

    Selecting the cd function by briefly pushing the media button, the cd audio source can be selected (only if a cd is loaded). Volume adjustment to adjust the volume, push the buttons +vol or –vol to increase/decrease the volume. Mute/pause function push the button briefly to activate the mute func- t...

  • Page 192

    • midrange (midrange adjustment) • treble (treble adjustment) • balance (right/left balance adjustment) • fader (front/rear balance adjustment) • loudness — if equipped (loudness function activation/deactivation) • equalizer — if equipped (activation and selection of factory equalization adjustments...

  • Page 193

    By pushing the or buttons briefly, the levels will change progressively. By pushing them down longer, the levels will change quickly. Select the value “0” to set the right and left audio outputs at the same level. Fader adjustment proceed as follows: 1. Push the audio button. 2. Push the or button t...

  • Page 194

    Curves can be adjusted. To deactivate the equalizer, select the “eq preset” function in the audio menu. To activate the equalizer, use the audio button to select one of the adjustments: • “eq user” (adjustment of 7 equalizer bands that can be changed by the user) • “classic” (equalizer preset for op...

  • Page 195

    Menu menu button functions push the menu button briefly to activate the menu function. Use the or buttons to scroll through the menu functions. To change the setting of the selected func- tion, use the or buttons. The current status of the selected function appears on the display. The functions mana...

  • Page 196

    On volume limit this function makes it possible to activate/deactivate the maximum volume limit when turning the radio on. The display shows the function status: • “on volume limit: on” – when the radio is turned on the volume level will be: – if the volume level is equal to or higher than the maxim...

  • Page 197

    Radio off function this function makes it possible to set the radio switching off mode by choosing between two methods. The chosen mode appears on the display: • “radio off: 00 min” — the radio turns off in connec- tion with the ignition key; the radio is turned auto- matically off as soon as the ke...

  • Page 198

    Frequency band selection with the radio mode active, press the fm or am tuner button briefly and repeatedly to select the desired recep- tion band. Each time the button is pressed the following bands are selected cyclically: • am, fm or sat (if equipped) each band is highlighted by the corresponding...

  • Page 199

    Manual tuning this is used to manually search for stations in the preselected band. Select the desired frequency band and then push briefly and repeatedly the or button to start the search in the desired direction. If the or button is pushed longer, the fast search starts and then stops when the but...

  • Page 200

    Siriusxm satellite radio program types program types can be selected by pushing the or buttons. The program type will change to the next category and the radio will then tune to first station in that program type. Pushing or buttons will tune to only the stations in that program type. Pushing the or...

  • Page 201

    Your service, either call the number listed on the display or visit the provider online. Caution! Neither sirius nor fiat is responsible for any errors in accuracies in the sirius data services or its use in vehicles. Siriusxm and all related marks and logos are trademarks of siriusxm radio inc. And...

  • Page 202

    Satellite radio antenna — if equipped the antenna for the satellite radio is mounted on the roof of the vehicle. Do not place items on the roof around the roof top antenna location. Objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items should b...

  • Page 203

    Cd loading/ejecting to load the cd, insert it gently into the slot to activate the motorized loading system, which will position it cor- rectly. The cd can be loaded with the radio off and the ignition key turned to on/run. In this case, the radio will remain off. When the radio is turned on, the la...

  • Page 204

    Display information when the cd player is operating, information will ap- pear on the display with the following meaning: • “track 5” indicates the cd track number. • “03:42” indicates the time elapsed since the start of the track (if the relevant menu function is activated). Track selection briefly...

  • Page 205

    Mp3 mode in addition to playing regular audio cds, the radio is also enabled to play cdroms on which compressed audio files have been recorded in an mp3 format. To guarantee optimal reproduction, it is advisable to use good quality cds burned at the lowest speed possible. The files on an mp3 cd are ...

  • Page 206

    Move to the mp3 session while playing by keeping the cd button pressed for more than two seconds. Note: when the function is activated the radio may take a few seconds to start playing. While checking the disc the display will show “cd reading.” if no mp3 files are detected, the radio will resume pl...

  • Page 207

    • if the mp3 files on a cd-rom are structured in sub-folders their structure is compressed to a single level structure, where the sub-folders are taken to the level of the main folders. Troubleshooting general sound volume low the fader function should be adjusted to the values “f” (front) only to p...

  • Page 208

    Operating instructions — hands-free phone refer to the appropriate “blue&me™ user’s manual” for further information. Personal/portable navigation device (pnd) a personal/portable navigation device (pnd) is avail- able as optional equipment for this vehicle, refer to the navigation user guide for fur...

  • Page 209

    Steering wheel audio controls the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pu...

  • Page 210

    Radio operation pushing the top of the switch will “seek” up for the next listenable station and pushing the bottom of the switch will “seek” down for the next listenable station. The button located in the center of the left-hand control will tune to the next preset station that you have pro- gramme...

  • Page 211

    5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. Note: if you experience difficulty in playing a particular disc, it may be damaged (e.G., scratched, reflective coat- ing removed, a hair, moist...

  • Page 212

    Manual heating and air conditioning the manual climate controls consist of a series of rotary dials and one inner push knob. 1. Temperature control rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial to the left into the blue area of the sca...

  • Page 213

    Note: • continuous use of the recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. • the use of the recirculation mode in cold or damp weather could cause windows to fog on the inside, because of moisture buildup inside the veh...

  • Page 214

    • mix air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. • defrost air is directed through...

  • Page 215

    • the system provides set-and-forget operation for op- timum comfort and convenience. • the system can be controlled manually, if desired. The atc system automatically maintains the interior comfort level desired by the occupant. 1. Auto temperature control (atc) button controls airflow, temperature...

  • Page 216

    Through the system in any mode you select. The blower speed increases as you push, or hold, the blower control up button and decreases when you push, or hold, the blower control down button. The blower fan speed may be set to any fixed speed by pushing the blower control up or down buttons. The fan ...

  • Page 217

    Side window demister outlets. Performing this function will cause the atc to switch into manual mode. 8. Panel mode air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. Performing this function will cause the atc to switch into manual mode. ...

  • Page 218

    Climate control functions air conditioning (a/c) the air conditioning (a/c) button allows the operator to manually activate or deactivate the air conditioning system. When in a/c mode with the atc set to a cool temperature, dehumidified air flows through the air outlets. If economy mode is desired, ...

  • Page 219

    Note: in cold weather, use of recirculation mode may lead to excessive window fogging. The recirculation feature may be unavailable (indicator light shall blink) if conditions exist that could create fogging on the inside of the windshield. On systems with manual climate con- trols, the recirculatio...

  • Page 220

    • the temperature can be displayed in u.S. Or metric units by selecting the us/m customer-programmable feature. Refer to the “electronic vehicle information center (evic) — customer-programmable features” in this section of the manual. Manual operation the system allows for manual selection of blowe...

  • Page 221

    Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging. Note: automatic temperature controls...

  • Page 222

    Operating tips chart 220 understanding your instrument panel.

  • Page 223: Starting And Operating

    Starting and operating contents ! Starting procedures . . . . . . . . . . . . . . . .225 ▫ manual transmission — if equipped . . . . . . .225 ▫ automatic transmission — if equipped . . . . .225 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .225 ▫ cold weather operation . . . . . . . ....

  • Page 224

    ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . . .241 ! Driving on slippery surfaces . . . . . . . . .242 ▫ acceleration . . . . . . . . . . . . . . . . . . . . . . . . .242 ▫ traction . . . . . . . . . . . . . . . . . . . . . . . . . . . .243 ! Driving through water . . . . . . . . ....

  • Page 225

    ! Tires — general information . . . . . . . .271 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . . .271 ▫ tire inflation pressures . . . . . . . . . . . . . . . . .273 ▫ tire pressures for high speed operation . . . .274 ▫ radial ply tires . . . . . . . . . . . . . . . . . . . . . .274 ▫...

  • Page 226

    ▫ materials added to fuel . . . . . . . . . . . . . . . .299 ▫ fuel system cautions. . . . . . . . . . . . . . . . . . .299 ▫ carbon monoxide warnings . . . . . . . . . . . . .300 ! Adding fuel . . . . . . . . . . . . . . . . . . . . . . . .301 ▫ fuel filler cap (gas cap) . . . . . . . . . . . . . ....

  • Page 227

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a numb...

  • Page 228

    Turn the ignition switch to the avv/acc (start) position and release it when the engine starts. If the engine fails to start within 10 seconds, turn the ignition switch to the stop (off/lock) position, wait 10 to 15 seconds, then repeat the “normal starting” procedure. Cold weather operation to prev...

  • Page 229

    3. If the engine fails to start within ten seconds, cycle the ignition to the stop (off/lock) position, wait five seconds to allow the starter to cool, then repeat the extended park starting procedure. 4. If the engine fails to start after eight attempts, allow the starter to cool for at least 10 mi...

  • Page 230

    Caution! (continued) • to prevent damage to the starter, do not continu- ously crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. After starting the idle speed is controlled automatically and it will decrease as the engine warms up. Turbocharger “cool dow...

  • Page 231

    Fully press the clutch pedal before you shift gears. As you release the clutch pedal, lightly press the accelerator pedal. Note: to shift into reverse from neutral, lift the ring under the knob and, at the same time move the gearshift lever to the right and then backward. Use each gear in numerical ...

  • Page 232

    Note: • clashing reverse gear, especially if vehicle is mov- ing, can result in transmission damage. • during cold weather, until the transmission lubricant is warm, you may experience slightly higher shift efforts. This is normal and not harmful to the trans- mission. Recommended shift speeds to us...

  • Page 233

    Downshifting proper downshifting will improve fuel economy and prolong engine life. Caution! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released. Damage...

  • Page 234

    Note: you must press and hold the brake pedal while shifting out of park. Warning! • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You c...

  • Page 235

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 236

    The electronically-controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles (kilomete...

  • Page 237

    Note: if the shift lever cannot be moved to the park, reverse, or neutral position (when pushed for- ward) it is probably in the autostick (+/-) position (beside the drive position). In autostick mode, the transmission gear (1, 2, 3, etc.) is displayed in the instrument cluster. Move the shift lever...

  • Page 238

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • your vehicle could move and injure you and others if it is not completely in park. Check by trying to mo...

  • Page 239

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and r...

  • Page 240

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off position to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ...

  • Page 241

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 242

    Range of torque converter clutch engagement. This is done to prevent transmission damage due to overheat- ing. During cold temperatures, transmission operation may be modified depending on engine coolant temperature. Normal operation will resume once the engine tempera- ture has risen to a suitable ...

  • Page 243

    If the transmission cannot be reset, authorized dealer service is required. Autostick autostick is a driver-interactive transmission feature providing manual shift control, giving you more control of the vehicle. Autostick allows you to maximize engine braking, eliminate undesirable upshifts and dow...

  • Page 244

    In snow or icy conditions. To select second or third gear after the vehicle is brought to a stop, tap the shift lever rearward (+) once or twice. • the system will ignore shift commands that would cause engine lugging or overspeed. An audible beep will sound if an inappropriate gear is requested. • ...

  • Page 245

    Warning! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have a collision. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet, mud, loose ...

  • Page 246

    Flowing/rising water warning! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flow- ing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicl...

  • Page 247

    Caution! • always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • determine the condition of the road or the path that is under water and if there are any obstacles in the wa...

  • Page 248

    Power steering the electric power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will vary its assist to provide light efforts while parking and good feel while driving. If the electric steering system experiences a fault that pr...

  • Page 249

    Note: • even if the power steering assistance is no longer operational, it is still possible to steer the vehicle. Under these conditions there will be a substantial increase in steering effort, especially at low speeds and during parking maneuvers. • if the condition persists, see your authorized d...

  • Page 250

    When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. Warning! • never leave children alone in a vehicle, or with access to ...

  • Page 251

    Caution! If the brake warning light remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. Sport mode manual transmission — if equipped the sport mode increases steering feedback to the driver with slig...

  • Page 252

    Automatic transmission — if equipped the sport mode increases steering feedback to the driver with slight increase in effort and changes the transmis- sion shift schedules for more aggressive shifting. This driving mode is useful while driving on twisty roads where more steering precision is desired...

  • Page 253

    Brake system your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability, the remaining system will still func- tion. However, there will be some loss of overall braking effectiveness. You may notice increased pedal travel during applica...

  • Page 254

    The abs includes an amber abs warning light. When the light is illuminated, the abs is not functioning. The system reverts to standard non-anti-lock brakes. Turning the ignition off and on again may reset the abs if the fault detected was only momentary. Warning! • pumping the anti-lock brakes will ...

  • Page 255

    Brake assist system (bas) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce...

  • Page 256

    Traction control system (tcs) this system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the tcs system, brake limit...

  • Page 257

    • gear selection matches vehicle uphill direction (i.E., vehicle in neutral (manual transmission), vehicle facing uphill is in forward gear; vehicle backing uphill is in reverse gear). Warning! There may be situations on minor hills with a loaded vehicle, or while pulling a trailer, when the system ...

  • Page 258

    Note: the esc off switch is located left of the steering column (manual transmission only). Esc off switch (automatic transmission) esc off switch (manual transmission) 256 starting and operating.

  • Page 259

    Warning! The electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esc cannot prevent all accidents, including those resulting from excessive speed in turns, driving on very...

  • Page 260

    Note: to improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, it may be desirable to switch to the partial off mode by pressing the switch. Once the situation requir- ing esc to be switched to the partial off mode is overcome, turn esc back on b...

  • Page 261

    The esc activation/malfunction indicator light (located in the instrument cluster) starts to flash as soon as the tires lose traction and the esc system becomes active. The esc activation/malfunction indicator light also flashes when tcs is active. If the esc activation/ malfunction indicator light ...

  • Page 262

    Tire safety information tire markings note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design stand...

  • Page 263

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it beg...

  • Page 264

    Example: 65, 85, 80 = aspect ratio in percent (%) – ratio of section height to section width of tire, or 10.5 = section width in inches (in) r = construction code – #r# means radial construction, or – #d# means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service descriptio...

  • Page 265

    Example: load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: • xl = extra load (or reinforced) tire, or • ll = light load tire or • c, d, e, f, g = load range associated with the maximum load a tire can carry at a...

  • Page 266

    Example: dot ma l9 abcd 0301 dot = department of transportation – this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 267

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours,...

  • Page 268

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) 266 starting and operating.

  • Page 269

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. Example tire placard location (b-pillar) tire and loading information placard 5 starting and operating 267.

  • Page 270

    3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to t...

  • Page 271

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 272

    270 starting and operating.

  • Page 273

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 274

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the v...

  • Page 275

    Tire inflation pressures the proper cold tire inflation pressure is listed on the driver’s side b-pillar or rear edge of the driver’s side door. At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judge- ment when determining p...

  • Page 276

    Inflation pressure should be increased by 3 psi (21 kpa), which equals 1 psi (7 kpa) for every 12°f (7°c) for this outside temperature condition. Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too ...

  • Page 277

    Tire repair if your tire becomes damaged, it may be repaired if it meets the following criteria: • the tire has not been driven on when flat. • the damage is only on the tread section of your tire (sidewall damage is not repairable). • the puncture is no greater than a ¼ of an inch (6 mm). Consult a...

  • Page 278

    Summer tires do not contain the all season designation or mountain/snowflake symbol on the tire sidewall. Use summer tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Warning! Do not use summer tires in snow/ice conditions. You could lose vehi...

  • Page 279

    While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states pro- hibit studded tires; therefore, local laws should be checked before using these tire types. Run flat tires — if equipped run flat tires a...

  • Page 280

    Rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended tire rotation pattern. Compact spare tire — if equipped the compact spare is for temporary emergency use only. You can identify if your vehicle is equipped with a compact spare by looki...

  • Page 281

    Full size spare — if equipped the full size spare is for temporary emergency use only. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, the ...

  • Page 282

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping. Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Warning! Fast spinning ti...

  • Page 283

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information. L...

  • Page 284

    Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressures. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance w...

  • Page 285

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 286

    Tire chains (traction devices) use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard against damage: • traction device must be of proper size for the tire, as recommended by the traction device manufacturer. • install on front tires. • due to limite...

  • Page 287

    Caution! (continued) • observe the traction device manufacturer’s instruc- tions on the method of installation, operating speed, and conditions for use. Always use the suggested operating speed of the device manufac- turer’s if it is less than 30 mph (48 km/h). • do not use traction devices on a com...

  • Page 288

    Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold tire pressure. The tire pressure will vary with temperature by about 1 psi (7 kpa) for every 12° f (6.5° c). This means that when the out...

  • Page 289

    The tpms will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold tire pressure on the placard. Once the low tire pressure warning (tire pressure monitoring telltale light) illuminates, yo...

  • Page 290

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, ...

  • Page 291

    Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. • the tpms is not a substitute for proper tire mainte- nance, and it is the driver’s responsibility to maintain correct tire pressure using an accurate tire gauge, even if un...

  • Page 292

    Xxx.X psi” text message will display when one or more of the four active road tire pressures are low. Should this occur, you should stop as soon as possible, check the inflation pressure of each tire on your vehicle, and inflate each tire to the vehicle’s recommended cold placard pressure value. The...

  • Page 293

    2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warn- ing limit, upon the next ignition key cycle, a chime will sound and the tire pressure monitoring telltale light will still turn on due to the low tire. 3. However, after driving the vehi...

  • Page 294

    The tpms consists of the following components: • receiver module • four tire pressure monitoring sensors • various tire pressure monitoring system messages, which display in the electronic vehicle information center (evic) • tire pressure monitoring telltale light tire pressure monitoring low pressu...

  • Page 295

    Light” will turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this information. Tpms warning when a system fault is detected, the “tire pressure monitoring telltale light” will flash on and off for 75 seconds and then remain on s...

  • Page 296

    A system fault can occur due to any of the following: 1. Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as the tpm sensors. 2. Installing aftermarket window tinting that contains materials that may block radio wave signals. 3. Accumula...

  • Page 297

    Telltale light” will flash on and off for 75 seconds and then remain on solid. In addition, the evic will display a “service tpm system” message and then display dashes (- -) in place of the pressure value. • for each subsequent ignition switch cycle, a chime will sound, the “tire pressure monitorin...

  • Page 298

    Fuel requirements — 1.4l engine this engine is designed to meet all emis- sion regulations and provide satisfactory fuel economy and performance when us- ing high-quality unleaded #regular# gaso- line with a minimum octane rating of 87. For optimum performance and fuel economy the use of 91 octane o...

  • Page 299

    Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required. Engine damage resulting from operating with a heavy spark #knock# may void or not be covered under the new vehicle warranty. P...

  • Page 300

    Problems that result from using methanol/gasoline blends are not the responsibility of the manufacturer. E-85 usage in non-flex fuel vehicles non-flex fuel vehicles (ffv) are compatible with gaso- line containing up to 10% ethanol (e10). Gasoline with higher ethanol content may void the new vehicle ...

  • Page 301

    Without mmt be used in your vehicle. The mmt content of gasoline may not be indicated on the gasoline pump, therefore, you should ask your gasoline retailer whether the gasoline contains mmt. Mmt is prohibited in federal and california reformulated gasoline. Materials added to fuel all gasoline sold...

  • Page 302

    Caution! (continued) • the use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle perfor- mance problems resulting from the use of such fuels or additives is not the respon...

  • Page 303

    Warning! (continued) • guard against carbon monoxide with proper main- tenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. Adding fuel fuel filler cap (gas cap) the gas ca...

  • Page 304

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel filler cap. A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting aftermar- ket cap can cause the “malfunction indicator light (mil)” to illuminate, due to fuel v...

  • Page 305

    Note: • when the fuel nozzle “clicks” or shuts off, the fuel tank is full. • tighten the gas cap about 1/4 turn until you hear one click. This is an indication that the cap is properly tightened. • if the gas cap is not tightened properly, the mil will come on. Be sure the gas cap is tightened every...

  • Page 306

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmission automatic transmission flat tow none transmission in neu- tral not allowed dolly tow front ok ok rear not allowed not allowed on trailer all ok ok 304 st...

  • Page 307

    This vehicle may be towed on a flatbed or vehicle trailer provided all four wheels are off the ground. This vehicle may also be towed using a tow dolly (with the front wheels off the ground). Vehicles equipped with manual transmissions may be flat towed (with all four wheels on the ground) at any le...

  • Page 309: Contents

    What to do in emergencies contents ! Hazard warning flashers . . . . . . . . . . .309 ! If your engine overheats . . . . . . . . . . . .309 ! Tire service kit — if equipped . . . . . . . . .310 ▫ tire service kit storage . . . . . . . . . . . . . . . . .311 ▫ tire service kit components and operatio...

  • Page 310

    ▫ jump-starting procedure . . . . . . . . . . . . . . . .338 ! Freeing a stuck vehicle . . . . . . . . . . . . .340 ! Shift lever override . . . . . . . . . . . . . . . .341 ! Towing a disabled vehicle . . . . . . . . . . .343 ▫ automatic transmission . . . . . . . . . . . . . . . . .344 ▫ manual tr...

  • Page 311

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the radio. Push the switch to turn on the hazard warning flashers. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Push the ...

  • Page 312

    Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the n...

  • Page 313

    Tire service kit storage the tire service kit is located under the front driver’s seat. Tire service kit components and operation tire service kit location tire service kit components 1 — sealant bottle 5 — mode select knob 2 — deflation button 6 — sealant hose (clear) 3 — pressure gauge 7 — air pum...

  • Page 314

    Using the mode select knob and hoses your tire service kit is equipped with the following symbols to indicate the air or sealant mode. Selecting air mode push in the mode select knob (5) and turn to this position for air pump operation only. Use the black air pump hose (7) when selecting this mode. ...

  • Page 315

    • the sealant bottle (1) and sealant hose (6) are a one tire application use and need to be replaced after each use. Always replace these components immediately at your original equipment vehicle dealer. • when the tire service kit sealant is in a liquid form, clean water, and a damp cloth will remo...

  • Page 316

    Warning! • do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the tire service kit. • do not use tire service kit or drive the vehicle under the following circumstances: – if the puncture in the tire t...

  • Page 317

    Warning! (continued) • tire service kit sealant solution contains latex. In case of an allergic reaction or rash, consult a phy- sician immediately. Keep tire service kit out of reach of children. If swallowed, rinse mouth imme- diately with plenty of water and drink plenty of water. Do not induce v...

  • Page 318

    4. Remove the cap from the valve stem and then screw the fitting at the end of the sealant hose (6) onto the valve stem. 5. Uncoil the power plug (8) and insert the plug into the vehicle’s 12 volt power outlet. Note: do not remove foreign objects (e.G., screws or nails) from the tire. (c) injecting ...

  • Page 319

    Note: if the mode select knob (5) is on air mode and the pump is operating, air will dispense from the air pump hose (7) only, not the sealant hose (6). If the sealant (white fluid) does flow through the sealant hose (6): 1. Continue to operate the pump until sealant is no longer flowing through hos...

  • Page 320

    3. Immediately disconnect the sealant hose (6) from the valve stem, reinstall the cap on the fitting at the end of the hose, and place the tire service kit in the vehicle storage location. Quickly proceed to (d) “drive ve- hicle.” caution! • the metal end fitting from power plug (8) may get hot afte...

  • Page 321

    (e) after driving: pull over to a safe location. Refer to “whenever you stop to use tire service kit” before continuing. 1. Push in the mode select knob (5) and turn to the air mode position. 2. Uncoil the power plug and insert the plug into the vehicle’s 12 volt power outlet. 3. Uncoil the air pump...

  • Page 322

    5. Remove the speed limit sticker from the instrument panel after the tire has been repaired. 6. Replace the sealant bottle (1) and sealant hose (6) assembly at your authorized dealer as soon as pos- sible. Refer to (f) “sealant bottle and hose replace- ment”. Note: when having the tire serviced, ad...

  • Page 323

    Wheel and tire torque specifications proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any time a wheel has been removed and reinstalled on the vehicle the lug nuts/bolts should be torqued using a properly calibrated torque wrench. Torque speci...

  • Page 324

    After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may ...

  • Page 325

    Warning! (continued) • being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be ra...

  • Page 326

    Spare tire removal the spare tire is stowed to the underbody below the cargo area. 1. Remove the plug located in the rear cargo area. 2. Fit the wrench tool over the drive nut. Use the wrench to rotate the nut counterclockwise until the spare is on the ground with enough slack in the cable to allow ...

  • Page 327

    Caution! The winch mechanism is designed for use with the jack wrench tool only. Use of an air wrench or other power tools is not recommended and they can dam- age the winch. 3. Pull the spare tire out from under the vehicle. 4. Tilt the retainer at the end of the cable and pull it through the cente...

  • Page 328

    Preparations for jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the whe...

  • Page 329

    6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. Note: passengers should not remain in the vehicle while the vehicle is being jacked. Jacking instructions warning! Carefully follow the...

  • Page 330

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 331

    2. Remove center cap. Note: before using the swivel wrench to remove the wheel bolts be sure to remove the center cap of the wheel by inserting the angled tab end of the swivel wrench into the notched part of the center cap. 3. Loosen, but do not remove, the wheel bolts by turning them to the left o...

  • Page 332

    Do not raise the vehicle until you are sure the jack is securely engaged. 4. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to th...

  • Page 333

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Using the swivel wrench, raise the vehicle by turning the jack screw to the right. Raise the vehicle only unt...

  • Page 334

    7. Install the spare wheel and wheel bolts with the cone shaped end of the bolts toward the wheel. Lightly tighten the bolts. To avoid the risk of forcing the vehicle off the jack, do not tighten the bolts fully until the vehicle has been lowered. 8. Lower the vehicle by turning the jack screw to th...

  • Page 335

    Road tire installation vehicles equipped with wheel covers 1. Mount the road tire on the axle. 2. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand. Do not use a hammer or excessive force to install the cover. Tire and wheel cover or center cap 1 — ...

  • Page 336

    3. Install the four wheel bolts with the cone shaped end of the nut toward the wheel. Lightly tighten the wheel bolts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel bolts fully until the vehicle has been lowered. Failure to follow this warning may result in...

  • Page 337

    4. Finish tightening the wheel bolts. Push down on the wrench while at the end of the handle for increased leverage. Refer to “torque specifications” in this sec- tion for correct wheel bolt torque. 5. After 25 miles (40 km) check the wheel bolt torque with a torque wrench to ensure that all wheel b...

  • Page 338

    Caution! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 volts or damage to the battery, starter motor, alternator or electrical system may occur. Preparations for jump-start the battery in your vehicle is located between the left front he...

  • Page 339

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 340

    Jump-starting procedure warning! Failure to follow this jump-starting procedure could result in personal injury or property damage due to battery explosion. Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Con...

  • Page 341

    5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. 6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the...

  • Page 342

    Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Then shift back and forth between drive and reverse (with automatic transmission) or 2nd gear an...

  • Page 343

    Caution! (continued) • revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h) while in gear (no trans- mission shifting occurring). Warning! Fast spinning tires can be dangerous....

  • Page 344

    4. Push and maintain firm pressure on the brake pedal. 5. Insert a small screwdriver or similar tool into the access hole, and push and hold the override release lever in. 6. Move the shift lever to the neutral position. 7. The vehicle may then be started in neutral. 8. Reinstall the shift lever ove...

  • Page 345

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial towing service. Towing condition wheels off the ground automatic transmission manual transmission flat tow none not allowed if transmission is operable: • transmission in neutral • 65 mph (10...

  • Page 346

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members ...

  • Page 347

    Caution! • do not flat tow any vehicle equipped with a conventional automatic transmission. Damage to the drivetrain will result. If these vehicles require towing, make sure all drive wheels are off the ground. • towing this vehicle in violation of the above re- quirements can cause severe transmiss...

  • Page 348

    • flash hazard lights as long as the battery has power or until the ignition key is turned off. • turn on the interior lights, which remain on as long as the battery has power or until the ignition key is removed. • unlock the doors automatically. After the event occurs, when the system is active, t...

  • Page 349

    5. Turn right turn signal switch on. Right turn light is on solid. Left turn light blinks. 6. Turn left turn signal switch on. Left turn light is on solid. Right turn light is on solid. 7. Turn left turn signal switch off. (turn signal switch must be placed in neutral state). Left turn light is off....

  • Page 351: Maintaining Your Vehicle

    Maintaining your vehicle contents ! Engine compartment — 1.4l . . . . . . . . . .351 ! Engine compartment — 1.4l turbo . . . .352 ! Onboard diagnostic system — obd ii . .353 ! Emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . . . .353 ! Replacement parts . ....

  • Page 352

    ▫ automatic transmission — if equipped . . . . .381 ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .383 ▫ convertible top care — if equipped . . . . . . .389 ! Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .391 ▫ interior fuses ....

  • Page 353

    Engine compartment — 1.4l 1 — engine coolant reservoir 5 — battery 2 — engine oil dipstick 6 — air cleaner filter 3 — brake fluid reservoir 7 — engine oil fill 4 — front distribution unit (fuses) 8 — washer fluid reservoir 7 maintaining your vehicle 351.

  • Page 354

    Engine compartment — 1.4l turbo 1 — engine coolant reservoir 5 — battery 2 — engine oil dipstick 6 — engine oil fill 3 — brake fluid reservoir 7 — washer fluid reservoir 4 — front distribution unit (fuses) 352 maintaining your vehicle.

  • Page 355

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 356

    Indicator light (mil)” is functioning and is not on when the engine is running, and that the obd ii system is ready for testing. Normally, the obd ii system will be ready. The obd ii system may not be ready if your vehicle was recently serviced, recently had a dead battery or a battery replace- ment...

  • Page 357

    Recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your obd ii system to update. A recheck with the above test routine may then indicate that the system is now ready. Regardless of whether your vehicle...

  • Page 358

    Maintenance procedures the pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed maintenance schedule, there are other components which may require servicing or replacement in the futu...

  • Page 359

    After a fully warmed engine is shut off. Do not check oil level before starting the engine after it has sat overnight. Checking engine oil level when the engine is cold will give you an incorrect reading. Checking the oil while the vehicle is on level ground, and approximately five minutes after a f...

  • Page 360

    Engine oil selection — 1.4l turbo engine for best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are api certified and meet the requirements of chrysler material standard ms- 12991. American petroleum institute (api) engi...

  • Page 361

    The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “engine compartment” in “main- taining your vehicle” for further information. Engine oil viscosity — 1.4l turbo engine (sae grade) mopar® sae 5w-40 f...

  • Page 362

    Station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection this manufacturer’s engines have a full-flow ...

  • Page 363

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 364

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be ...

  • Page 365

    Caution! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air condi- tioning components. Such damage is not covered by the new vehicle limited warranty. Refrigerant recovery and recycling r134a — if equipped r-134a air conditioning refrigerant is a hydrofl...

  • Page 366

    The a/c air filter is located in the fresh air inlet on the lower right of center console. Perform the following procedure to replace the filter: 1. Remove the torx® screw that secures the passenger side console closeout cover. 2. Pull the console closeout cover rearward to disengage the front retai...

  • Page 367

    4. Remove the a/c air filter by pulling it straight out of the housing. Take note of the air filter position indica- tors. 5. Install the a/c air filter with the air filter position indicators pointing in the same direction as removal. Air filter cover screw locations a/c air filter 7 maintaining yo...

  • Page 368

    Caution! The a/c air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 6. Install the passenger side console closeout. Refer to the “maintenance schedule” for the proper mainte...

  • Page 369

    Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield or rear window. Avoid using the wiper blades to remove frost or ice from the windshield or rear window. Make s...

  • Page 370

    Note: the rear wiper arm cannot be raised fully up- ward unless the pivot cap is raised first. 2. Lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder. ...

  • Page 371

    5. Lower the wiper blade and snap the pivot cap into place. Adding washer fluid the windshield washer fluid reservoir is located in the engine compartment, and the fluid level should be checked at regular intervals. Fill the reservoir with wind- shield washer solvent (not engine coolant/ antifreeze)...

  • Page 372

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips/exhaust gas” in “things to know before starting your vehicle” for further...

  • Page 373

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 374

    Cooling system warning! • when working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at any time the ignition switch is in the on position. • you or others can be badly burned by hot eng...

  • Page 375

    If the engine coolant (antifreeze) is dirty or contains visible sediment, have an authorized dealer clean and flush with oat coolant (antifreeze) (conforming to ms.90032). Refer to the “maintenance schedule” for the proper maintenance intervals. Selection of coolant refer to “fluids, lubricants, and...

  • Page 376

    Caution! (continued) • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • this vehicle has not been designed for use with...

  • Page 377

    • use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain ...

  • Page 378

    Warning! • do not open hot engine cooling system. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap w...

  • Page 379

    Points to remember note: when the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment. This is nor- mally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vapor- ized when th...

  • Page 380

    Brake system in order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “maintenance schedule” for the proper maintenance intervals. Warning! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot rest...

  • Page 381

    Use only manufacturer’s recommended brake fluid. Re- fer to “fluids, lubricants, and genuine parts” in “main- taining your vehicle” for further information. Warning! • use only manufacturer’s recommended brake fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for ...

  • Page 382

    Warning! (continued) • do not allow petroleum-based fluid to contaminate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in a collision. Caution! Use of improper brake fluids will affect overall clutch system performance. Improper...

  • Page 383

    Note: if contaminated with water, the fluid should be changed immediately. Automatic transmission — if equipped selection of lubricant it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s specified transmission fluid. R...

  • Page 384

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating cond...

  • Page 385

    Appearance care and protection from corrosion protection of body and paint from corrosion vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons a...

  • Page 386

    • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar® super kleen bug and tar remover to remove. • use a high quality cleaner wax, such as mopar® cleaner wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • av...

  • Page 387

    • if you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • if a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • use mopar® touch up paint on scratches as soon as possible. You...

  • Page 388

    Stain repel fabric cleaning procedure — if equipped stain repel seats may be cleaned in the following man- ner: • remove as much of the stain as possible by blotting with a clean, dry towel. • blot any remaining stain with a clean, damp towel. • for tough stains, apply mopar® total clean, or a mild ...

  • Page 389

    Warning! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Caution! Do not use alcohol and alcohol-based and/or keton based cleaning products to clean leather seats, as damage to the seat may result. Clean...

  • Page 390

    Instrument panel cover the instrument panel cover has a low glare surface which minimizes reflections on the windshield. Do not use protectants or other products which may cause undesir- able reflections. Use soap and warm water to restore the low glare surface. Instrument panel bezels caution! When...

  • Page 391

    Replace the belts if they appear frayed or worn or if the buckles do not work properly. Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immed...

  • Page 392

    Immediate removal of any contaminant is recommended. Regular washing of the top will enhance its life and appearance, and make successive cleanings easier. Do not subject the top to excessive heat. Frequently vacuum the top and storage compartment. Washing hand washing is highly recommended. Automat...

  • Page 393

    Scrub in all directions, covering an area of about two square feet at a time. Avoid heavy scrubbing. Rinse the entire vehicle with water to remove all soap and dirt from the top fabric and to prevent streaking on painted and chrome surfaces. Allow the top to dry before lowering. Vacuuming the top wi...

  • Page 394

    Warning! (continued) • if a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. Interior fuses the interior fuse panel is part of the body control module (bcm) and is l...

  • Page 395

    Cavity vehicle fuse number mini fuse description 4 f38 20 amp yellow central door locking 5 f36 10 amp red diagnostic socket, car radio, climate control system 6 f43 20 amp yellow bi-directional washer 7 f48 20 amp yellow passenger power window 8 f13 7.5 amp brown left low beam, headlamp leveling 9 ...

  • Page 396

    Underhood fuses the front distribution unit is located on the right side of the engine compartment, next to the battery. To access the fuses, press the release tabs and remove the cover. The id number of the electrical component correspond- ing to each fuse can be found on the back of the cover. Fro...

  • Page 397

    Cavity maxi fuse mini fuse description f01 60 amp blue – body controller f02 20 amp yellow – audio amplifier f03 20 amp yellow – ignition switch f04 40 amp orange – anti-lock brake pump f05 70 amp tan – electric power steering f06 20 amp yellow – radiator fan - single speed f06 30 amp green – radiat...

  • Page 398

    Cavity maxi fuse mini fuse description f16 – 7.5 amp brown transmission f17 – 25 amp clear powertrain (multiair – if equipped) f17 – 15 amp blue powertrain f18 – 15 amp blue powertrain f18 – 5 amp tan powertrain (multiair – if equipped) f19 – 7.5 amp brown air conditioning f20 – 15 amp blue heated s...

  • Page 399

    Cavity maxi fuse mini fuse description f85 30 amp green – rear defroster f87 – 5 amp tan rear defroster f90 – 5 amp tan heated mirrors – if equipped vehicle storage if you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • disconnect t...

  • Page 400

    Replacement bulbs interior bulbs bulb number overhead lamp c5w courtesy lamp w5w exterior bulbs bulb number front low and high beam headlamp hir2ll front parking/daytime running lamps w21/5w front fog lamps h11ll front side marker lamps w3w front turn signal lamps wy21w side direction lamps wy5w rea...

  • Page 401

    Bulb number rear tail and stop lamps p21/5w rear backup lamps w16w center high mounted stop lamp w5w license plate lamps led (see authorized dealer) note: numbers refer to commercial bulb types that can be purchased from your authorized dealer. If a bulb needs to be replaced, visit your authorized d...

  • Page 402

    Front turn signal, parking and daytime running lamps 1. Turn the steering wheel completely to the left or right. 2. Open the wheel housing access door. 3. Remove the plastic cap from the back of the lamp housing. 4. Rotate bulb/socket counter-clockwise. 5. Remove the bulb and replace as needed. 6. I...

  • Page 403

    Front fog lamps to replace the front fog lights, see your authorized dealer. Front/rear side marker lamps 1. Remove portion of the wheel liner to allow hand access to side marker lamp. 2. Rotate the bulb socket counterclockwise, and remove the bulb and socket assembly from the housing. 3. Pull the b...

  • Page 404

    4. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise. 5. Remove the backup lamp bulb by pulling straight out. 6. Replace lamps as required and reinstall lamp. Center high mounted stop lamp (chmsl) 1. Remove the two guard caps and the two fastening scr...

  • Page 405

    Fluid capacities u.S. Metric fuel (approximate) 10.5 gallons 40 liters engine oil with filter 1.4l/1.4l turbo engine 4 quarts 3.8 liters cooling system 1.4l/1.4l turbo engine (mopar® antifreeze/engine coolant 10 year/150,000 mile formula) — with manual transmission 4.6 quarts 4.4 liters 1.4l/1.4l tu...

  • Page 406

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant - 1.4l/1.4l turbo engine we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) meeting the require- ments of chrysler material standard ms.90...

  • Page 407

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 408

    Chassis component fluid, lubricant, or genuine part manual transmission – if equipped we recommend you use mopar® c635 ddct/mtx transmission fluid automatic transmission – if equipped use only mopar® aw-1 automatic transmission fluid or equivalent. Failure to use the correct fluid may affect the fun...

  • Page 409: Maintenance Schedules

    Maintenance schedules contents ! Maintenance schedule . . . . . . . . . . . . .408 ▫ maintenance chart . . . . . . . . . . . . . . . . . . . .410 8.

  • Page 410

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 411

    Check the tire inflation pressures and look for unusual wear or damage. Check the fluid levels of the coolant reservoir and brake master cylinder, and fill as needed. Check function of all interior and exterior lights. Required maintenance intervals refer to the maintenance schedules on the followin...

  • Page 412

    Maintenance chart refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 1...

  • Page 413

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 414

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 415

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 417: Contents

    If you need consumer assistance contents ! Suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .416 ▫ prepare for the appointment. . . . . . . . . . . . .416 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .416 ▫ be reasonable with requests ....

  • Page 418

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 419

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 420

    Has access to a tdd or a conventional teletypewriter (tty) in the united states, can communicate with the manufacturer by dialing 1-800-380-chry. Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by bell canada. For tty teletypewrite...

  • Page 421

    Warning! Engine exhaust (internal combustion engines only), some of its constituents, and certain vehicle compo- nents contain, or emit, chemicals known to the state of california to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids contained in vehicles and cer...

  • Page 422

    You can also obtain other information about motor vehicle safety from http://www.Safercar.Gov. In canada if you believe that your vehicle has a safety defect, you should contact the customer service department imme- diately. Canadian customers who wish to report a safety defect to the canadian gover...

  • Page 423

    Problems the first time, using step-by-step troubleshoot- ing and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment. Owner’s manuals these owner’s manuals have been prepared with the assistance of service and engineering specialists to ac- quaint you with...

  • Page 424

    Significantly from the norm due to variations in driving habits, service practices, and differences in road charac- teristics and climate. Traction grades the traction grades, from highest to lowest, are aa, a, b, and c. These grades represent the tire’s ability to stop on wet pavement, as measured ...

  • Page 425

    Warning! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive load- ing, either separately or in combination, can cause heat buildup and possible tire failure. 9 if you need consumer assistance 423.

  • Page 427: Index

    Index 10

  • Page 428

    Adding engine coolant (antifreeze) . . . . . . . . . . . .374 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .301 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .369 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .299 air bag . . . . . . . . ....

  • Page 429

    Automatic transmission . . . . . . . . . . . . . . . . . . . .231 adding fluid . . . . . . . . . . . . . . . . . . . . . . . . . .382 fluid and filter changes . . . . . . . . . . . . . . . . . .382 fluid change . . . . . . . . . . . . . . . . . . . . . . . . . .382 fluid level check . . . . . . . . ...

  • Page 430

    Cellular phone . . . . . . . . . . . . . . . . . . . . . . . . . . .209 chains, tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . .284 change oil indicator . . . . . . . . . . . . . . . . . . . . . . .408 changing a flat tire . . . . . . . . . . . . . . . . . . . . . . .322 chart, tire si...

  • Page 431

    Coolant capacity . . . . . . . . . . . . . . . . . . . . . . .404 coolant level . . . . . . . . . . . . . . . . . . . . . . . . . .372 disposal of used coolant . . . . . . . . . . . . . . . . .376 drain, flush, and refill . . . . . . . . . . . . . . . . . . .372 inspection . . . . . . . . . . . . . ...

  • Page 432

    New trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166 start of trip procedure . . . . . . . . . . . . . . . . . . .166 trip computer . . . . . . . . . . . . . . . . . . . . . . . . .165 trip functions . . . . . . . . . . . . . . . . . . . . . . . . .167 emergency, in case of hazard w...

  • Page 433

    Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . .360 engine oil disposal . . . . . . . . . . . . . . . . . . . . .359 flashers turn signal . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 flooded engine starting . . . . . . . . . . . . . . . . . . . .227 fluid, brake . . . ...

  • Page 434

    General information . . . . . . . . . . . . . . . . . . . . . . .295 general maintenance. . . . . . . . . . . . . . . . . . . . . . .356 glass cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .387 hazard driving through flowing, rising, or shallow standing water . . . . . . . . . . . . ....

  • Page 435

    Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 key, sentry (immobilizer) . . . . . . . . . . . . . . . . . . . .13 lane change assist . . . . . . . . . . . . . . . . . . . . . . . .112 lap/shoulder belts. . . . . . . . . . . . . . . . . . . . . . . . .30 latches . . . ....

  • Page 436

    Locks automatic door . . . . . . . . . . . . . . . . . . . . . . . . .23 door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 power door . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 lubrication, body . . . . . . . . . . . . . . . . . . . . . . . . .366 lug nuts . . ....

  • Page 437

    Change interval . . . . . . . . . . . . . . . . . . . . . . . .357 checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .356 disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .359 filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .360 filter disposal ....

  • Page 438

    Rear liftgate (sedan) . . . . . . . . . . . . . . . . . . . . . . .25 rear window features . . . . . . . . . . . . . . . . . . . . .139 recorder, event data . . . . . . . . . . . . . . . . . . . . . . .56 recreational towing . . . . . . . . . . . . . . . . . . . . . . .304 reformulated gasoline . . ...

  • Page 439

    Seat belt maintenance . . . . . . . . . . . . . . . . . . . . . .388 seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 child restraint . . . . . . . . . . . . . . . . . . . . . . . . . .57 extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 front seat . ...

  • Page 440

    Tilt column . . . . . . . . . . . . . . . . . . . . . . . . . . .118 wheel, tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . .118 steering wheel audio controls . . . . . . . . . . . . . . .207 steering wheel mounted sound system controls . . .207 storage . . . . . . . . . . . . . . . . . ....

  • Page 441

    Tread wear indicators . . . . . . . . . . . . . . . . . . . .280 tire safety information . . . . . . . . . . . . . . . . . . . . .260 tire service kit . . . . . . . . . . . . . . . . . . . . . . . . . . .310 to open hood . . . . . . . . . . . . . . . . . . . . . . . . . . .108 towing . . . . . . . ....

  • Page 442

    Adding fluid . . . . . . . . . . . . . . . . . . . . . . . . . .369 washers, windshield . . . . . . . . . . . . . . . . . . . . . . .115 washing vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .383 water driving through . . . . . . . . . . . . . . . . . . . . . . . .243 wheel and wheel tri...

  • Page 443

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 444

    Chrysler group llc o w n e r ’ s m a n u a l 2 0 1 5 2 0 1 5 f ia t 5 0 0 e 15bev24-126-aa first edition printed in u.S.A. Fiat 500e.