1. DL manuals
  2. Fiat
  3. Automobile
  4. 500 Abarth
  5. Owner's Manual

Fiat 500 Abarth Owner's Manual

Manual is about: 2013

Summary of 500 Abarth

  • Page 1

    Fiat 500 abarth chrysler group llc o w n e r ’ s m a n u a l 2 0 1 3 2013 fia t 500 abar th 13fx24-126-ae fifth edition rev 1 printed in u.S.A..

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understa...

  • Page 5

    Introduction contents ! Introduction . . . . . . . . . . . . . . . . . . . . . . . .4 ! How to use this manual . . . . . . . . . . . . . .5 ! Warnings and cautions . . . . . . . . . . . . . .7 ! Vehicle identification number . . . . . . . .7 ! Vehicle modifications/alterations . . . .8 1.

  • Page 6

    Introduction congratulations on selecting your new vehicle. Be as- sured that it represents precision workmanship, distinc- tive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engineering spe...

  • Page 7

    When it comes to service, remember that your authorized studio knows your vehicle best, has factory-trained tech- nicians and genuine parts, and cares about your satisfac- tion. How to use this manual consult the table of contents to determine which section contains the information you desire. Since...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owners manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss importan...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped vin location 8 introduction.

  • Page 11

    Things to know before starting your vehicle contents ! A word about your keys . . . . . . . . . . . . .11 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .11 ▫ locking doors with a key. . . . . . . . . . . . . . . .13 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .13 ! Sentry k...

  • Page 12

    ▫ power window switches . . . . . . . . . . . . . . . . .24 ! Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 ! Occupant restraints . . . . . . . . . . . . . . . .26 ▫ lap/shoulder belts . . . . . . . . . . . . . . . . . . . .29 ▫ lap/shoulder belt untwisting procedure . . . . .34...

  • Page 13

    A word about your keys the key fob contains the remote keyless entry (rke) transmitter with an integrated key. To use the mechanical key simply press the mechanical key release button . The vehicle is supplied with a code card containing key code numbers to order duplicate keys, and the autho- rized...

  • Page 14

    Warning! • before exiting a vehicle, always turn the ignition to the off/lock position, apply the parking brake, shift the transmission into reverse gear, and remove the key fob from the ignition. When leav- ing the vehicle, always lock your vehicle. • never leave children alone in a vehicle, or wit...

  • Page 15

    Warning! (continued) • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Caution! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unatt...

  • Page 16

    Note: a key which has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle. If the vehicle security light is on after the key is turned to the on/run position, it indicates that there is a problem with the electronics. Cau...

  • Page 17

    General information the sentry key® system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference that may be received, including interference ...

  • Page 18

    Within five seconds, to unlock all doors and the liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Remote key unlock, driver door/all doors 1st press this feature lets you program the system to unlock either the driver’s doo...

  • Page 19

    Power top open. The roof will stop opening when- ever the unlock button on the key fob is released, or when it reaches the spoiler position note: if your power convertible top does not open with the remote, please refer to the #power convertible top relearn procedure” in “understanding the features ...

  • Page 20

    To lock the doors and liftgate press and release the lock button on the rke transmit- ter to lock all doors and the liftgate. The turn signal lights will flash and the horn will chirp to acknowledge the signal. If a door is ajar the turn signal lights will flash at an increased rate and there will b...

  • Page 21

    3. Take out the battery case. Remove and replace the battery observing its polarity. 4. Refit the battery case inside the key fob and turn the screw to lock it into place. Key fob screw location battery case removed 2 things to know before starting your vehicle 19.

  • Page 22

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 23

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. (continued) warning! (continued) • for personal security and safety in the event of an collision, lock the vehicle doors as you drive as well as when you park ...

  • Page 24

    Warning! (continued) • do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with keyless enter-n-go in the acc or on/run mode. A child could operate power windows, other con- trols, or move the vehicle. Caution!...

  • Page 25

    Autoclose when enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). The auto door lock feature can be enabled or disabled using electronic vehicle information center (evic). To change the autoclose setting in the evic, proceed as follows: 1. Briefly pres...

  • Page 26

    Power windows power window switches there are single window controls located on the shifter bezel, below the climate controls, which operate the driver and passenger door windows. The window con- trols will operate when the ignition switch is in the on/run position. Warning! Never leave children una...

  • Page 27

    Down automatically. To cancel the auto-down move- ment, operate the switch in either the up or down direction and release the switch. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeti...

  • Page 28

    Warning! • driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • if you are required to drive with the liftgate open, make sure that all windows are c...

  • Page 29

    • all seat belt systems (except the driver’s) include automatic locking retractors (alrs), which lock the seat belt webbing into position by extending the belt all the way out and then adjusting the belt to the desired length to restrain a child seat or secure a large item in a seat — if equipped pl...

  • Page 30

    Ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm. You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should always wear their lap and shoulder belts...

  • Page 31

    Warning! (continued) • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • side air ...

  • Page 32

    Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure ever...

  • Page 33

    The belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” pulling out the latch plate inserting latch plate into buckle 2 things to know before s...

  • Page 34

    Warning! • a belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal inju- ries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you prop- erly. In a sudden stop you...

  • Page 35

    4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. War...

  • Page 36

    6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed posi- tion. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. Warning! A frayed or torn belt could rip apart in a collision and leave you with no protec...

  • Page 37

    Restraints” section. The chart below defines the type of feature for each seating position. Driver passenger first row n/a alr second row alr alr • n/a — not applicable • alr — automatic locking retractor if the passenger seating position is equipped with an alr and is being used for normal usage: o...

  • Page 38

    How to engage the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in t...

  • Page 39

    Seat belt pretensioners the seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by assuring that the belt is tight about the oc...

  • Page 40

    Unbuckled while traveling at speeds greater than 5 mph (8 km/h), beltalert® will provide both audio and visual notification. The front passenger seat beltalert® is not active when the front passenger seat is unoccupied. Beltalert® may be triggered when an animal or heavy object is on the front passe...

  • Page 41

    Seat belts and pregnant women we recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt lo...

  • Page 42

    Note: the driver and front passenger advanced front air bags are certified to the federal regulations for advanced air bags. The advanced front air bags are designed to allow the air bags to have different inflation levels based on several factors, including the severity and type of collision. This ...

  • Page 43

    Air bag system components your vehicle may be equipped with the following air bag system components: • occupant restraint controller (orc) • air bag warning light • steering wheel and column • instrument panel • supplemental driver side knee air bag • knee impact bolsters • driver advanced front air...

  • Page 44

    Warning! (continued) • do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air ba...

  • Page 45

    Deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air bag only. Supplemental side air bag inflatable curtain (sabic) supplemental side air bag inflatable curtains (sabic) may offer side-impact protection to front and rear seat outboard ...

  • Page 46

    The system includes side impact sensors that are cali- brated to deploy the seat-mounted side air bags (sab) and sabic during impacts that require air bag occupant protection. Sab and sabic air bags are a supplement to the seat belt restraint system. Occupants, including children who are up against ...

  • Page 47

    Warning! (continued) • your vehicle is equipped with sabic air bags, do not have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle. Do not add roof racks that require perma- nent attachments (bolts or screws) for installation on the vehicle roof. Do ...

  • Page 48

    Orc deploys the advanced front air bags, supplemen- tal driver side knee air bag, supplemental side air bag inflatable curtain (sabic), supplemental seat-mounted side air bags (sab), and front seat belt pretensioners, as required, depending on several factors, including the severity and type of impa...

  • Page 49

    On/run or start position. If the key is in the off/ lock position, or not in the ignition, the air bag system is not on and the air bags will not inflate. The orc contains a backup power supply system that may deploy the air bags even if the battery loses power or it becomes disconnected prior to de...

  • Page 50

    Quantity of non-toxic gas is generated to inflate the advanced front air bags. Different air bag inflation rates are possible, based on several factors, including the collision type and severity. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out...

  • Page 51

    Between the occupant and the door. The sab fully inflate in about 10 milliseconds. The side air bag moves at a very high speed and with such a high force that it could injure you if you are not seated properly, or if items are positioned in the area where the side air bag inflates. This especially a...

  • Page 52

    Power remains intact, depending on the nature of the event, the orc will determine whether to have the enhanced accident response system perform the follow- ing functions: • cut off fuel to the engine. • flash hazard lights as long as the battery has power or until the ignition key is turned off. • ...

  • Page 53

    Customer action customer will see 1. Turn ignition off. (turn signal switch must be placed in neutral state). 2. Turn ignition on. Left turn light is off. Right turn light blinks. 3. Turn right turn signal switch on. Right turn light is on solid. Left turn light blinks. 4. Turn left turn signal swit...

  • Page 54

    If a reset procedure step is not completed within 45 seconds, then the turn signal lights will turn off and the reset procedure must be performed again in order to be successful. If a deployment occurs the advanced front air bags are designed to deflate immediately after deployment. Note: front and/...

  • Page 55

    Do not drive your vehicle after the air bags have de- ployed. If you are involved in another collision, the air bags will not be in place to protect you. Warning! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and th...

  • Page 56

    Warning! (continued) • do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized studio for any air bag system service. If your seat, including your trim cover and cushion,...

  • Page 57

    Note: if the speedometer, tachometer, or any engine related gauges are not working, the occupant restraint controller (orc) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the body control module (bcm) fuse block inside the vehicle for blown fuses. ...

  • Page 58

    To read data recorded by an edr, special equipment is required, and access to the vehicle or the edr is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equip- ment, can read the information if they have access to the vehicle or the edr. ...

  • Page 59

    Note: • for additional information, refer to www.Seatcheck.Org or call 1–866–seatcheck. Cana- dian residents should refer to transport canada’s website for additional information: • http://www.Tc.Gc.Ca/eng/roadsafety/ safedrivers-childsafety-index-53.Htm warning! In a collision, an unrestrained chil...

  • Page 60

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child re- straint either an infant carrie...

  • Page 61

    Infants and child restraints safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carrie...

  • Page 62

    Have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat. Children should remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above t...

  • Page 63

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 64

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 65

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 66

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 64 things to know before starting your vehicle.

  • Page 67

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and teth...

  • Page 68

    Can two child restraints be attached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to in- stall a child seat in the center position next to a child s...

  • Page 69

    Locating the latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel the...

  • Page 70

    Locating the latch anchorages in addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to...

  • Page 71

    2. Loosen the adjusters on the lower straps and on the tether strap of the child seat so that you can more easily attach the hooks or connectors to the vehicle anchorages. 3. Place the child seat between the lower anchorages for that seating position. For some second row seats, you may need to recli...

  • Page 72

    How to stow an unused alr seatbelt when using the latch attaching system to install a child restraint, stow all alr seat belts that are not being used by other occupants or being used to secure child restraints. An unused belt could injure a child if they play with it and accidentally lock the seatb...

  • Page 73

    Installing child restraints using the vehicle seat belt the seat belts in the passenger seating positions are equipped with either a switchable automatic locking retractor (alr) or a cinching latch plate or both. Both types of seat belts are designed to keep the lap portion of the seat belt tight ar...

  • Page 74

    Lap/shoulder belt systems for installing child restraints in this vehicle 72 things to know before starting your vehicle.

  • Page 75

    What is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a for- ward facing child restrai...

  • Page 76

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. 2. Pull enough of the seat belt webbing fro...

  • Page 77

    9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. Installing a...

  • Page 78

    Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. If the buckle or the cinching latch plate is too close to the belt path opening of the child restraint, you may have trouble tightening the seat belt. If this happens, discon- nect the latch p...

  • Page 79

    3. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. 4. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. Warning! • an incorrectly anchored tether strap could lead to increased head motion and possib...

  • Page 80

    Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. Engine break-in recommendations a long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 k...

  • Page 81

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be serious...

  • Page 82

    Warning! (continued) • if it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. The best protection against carbon monoxide entry into the vehicle body is a properly maintained ...

  • Page 83

    Air bag warning light the light should come on and remain on for four to eight seconds as a bulb check when the ignition switch is first turned on. If the light is not lit during starting, see your authorized studio. If the light stays on, flickers, or comes on while driving, have the system checked...

  • Page 84

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 85

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 87

    Understanding the features of your vehicle contents ! Power convertible top — if equipped . .88 ▫ lowering the power top. . . . . . . . . . . . . . . . .88 ▫ raising the power top . . . . . . . . . . . . . . . . . .89 ▫ power convertible top relearn procedure . . . . .90 ▫ wind stop . . . . . . . . ...

  • Page 88

    ▫ ez entry feature . . . . . . . . . . . . . . . . . . . . . .106 ▫ memory feature . . . . . . . . . . . . . . . . . . . . . .107 ▫ heated seats — if equipped . . . . . . . . . . . . .107 ▫ head restraints . . . . . . . . . . . . . . . . . . . . . . .108 ! To open and close the hood . . . . . . . . ...

  • Page 89

    ▫ to vary the speed setting . . . . . . . . . . . . . . .123 ▫ to accelerate for passing . . . . . . . . . . . . . . . .123 ! Rear park assist — if equipped . . . . . . . .124 ▫ rear park assist sensors . . . . . . . . . . . . . . . .124 ▫ rear park assist alerts. . . . . . . . . . . . . . . . . .12...

  • Page 90

    Power convertible top — if equipped on vehicles equipped with a power convertible top, the power convertible top switch is located on the overhead console. The switch contains two buttons. The passenger side button, is used to open the power top, and the driver side button, is used to close the powe...

  • Page 91

    Note: vertical movement only operates in auto open/ close mode. Raising the power top auto close from the convertible top fully open position, push the top close button for approximately one second for the three-quarter open/spoiler position. Push the top close button for approximately one second a ...

  • Page 92

    Caution! (continued) • use care when washing the vehicle, water pressure directed at the weather strip seals may cause water to leak into the vehicles interior. Warning! The convertible top does not provide the structural protection that a reinforced metal roof does and the fabric top cannot be expe...

  • Page 93

    7. Continue to hold the closed button until the top begins to cycle fully open, then release the closed button. At the end of step 7 the top will automatically cycle to the fully open position, and then close to the 1/4 open position. This will confirm that the relearn procedure was success- ful. Au...

  • Page 94

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activa...

  • Page 95

    Caution! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Power mirrors the power mirror controls are located on the driver’s door trim panel. The power mirror controls consist ...

  • Page 96

    Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move. Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror co...

  • Page 97

    Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster if equipped. Some vehicles may not be equipped with rear window defroster, in this case the heated mirrors will still function as intended. Refer t...

  • Page 98

    Blue&me™ hands-free communication — if equipped overview windows mobile™-based fiat blue&me™ is a per- sonal telematic system enabling you to use communica- tion and entertainment applications expressly designed for use in the car. The blue&me™ system installed on your car is equipped with a hands-f...

  • Page 99

    The hands-free kit the basic characteristic of this hands-free kit is voice recognition with bluetooth® wireless technology. With this system you can make and receive calls safely and securely by using either voice commands or buttons on the steering wheel. This can be done under any driving conditi...

  • Page 100

    For further details on the mobile phones supported by blue&me™, refer to section blue&me™ supported mobile phones. To get started with blue&me™ hands-free kit with voice recognition, you have to simply pair your bluetooth® wireless technology enabled mobile phone with the system. Pairing is an opera...

  • Page 101

    (last calls and phonebook ) and the media player. To activate settings when travelling you can only use voice commands. The hands-free kit enables the following operations: • contact calling by voice — you can call a contact in your mobile phone phonebook using your voice. You can also call a contac...

  • Page 102

    After pairing and connecting your phone with the blue&me™ system, you can make phone calls by speaking keywords or pressing buttons on the steering wheel. When using the hands-free phone, the audio output of a phone conversation is heard through your car sound speakers. Message reader the blue&me™ m...

  • Page 103

    • to call the sms text sender using the buttons on the steering wheel or voice commands. • to delete individual messages or the entire inbox using the buttons on the steering wheel or voice commands. The blue&me™ system can also recognize and read abbreviations, if any (e.G. “iluvu” will be read lik...

  • Page 104

    Note: • the media player does not support audio files com- pressed with other formats and drm (digital right management) protected audio files. Non-supported audio files that may be present on the usb device will be ignored. • to use the media player, you have to simply connect (directly or by an ex...

  • Page 105

    Warning! (continued) • keep the user’s guide in the car: when kept in the car, the user’s guide will be a ready reference for you and other users unfamiliar with the system. Please make certain that before using the system for the first time, all persons have access to the user’s guide and read its ...

  • Page 106

    Front seats forward/rearward adjustment your vehicle may be equipped with either an adjusting handle or adjusting bar that is located at the front of the seats, near the floor. While sitting in the seat, lift up on the adjusting handle or bar and move the seat forward or rearward. Release the adjust...

  • Page 107

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 108

    Seat height adjustment the driver’s seat height can be raised or lowered by using a lever, located on the outboard side of the seat. Pump the lever upward to raise the seat height, or pump the lever downward to lower the seat height. Ez entry feature the driver and front passenger seats have an ez e...

  • Page 109

    Lift the seatback upright and push the seat rearward to its locked position once the rear passengers are seated. Memory feature the driver seat also has a memory feature, which can operate in two ways: memory function option 1 — full seat back and track fore/aft position memory: after using the ez e...

  • Page 110

    Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially ...

  • Page 111

    Rear head restraints to raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. Refer to “occupant restraints” in “things to know before starting your vehicle”...

  • Page 112

    2. Rotate the safety catch under the front edge of the hood, near the center, and raise the hood. Lift the hood prop rod that clips to the right side (left side when standing in front of the hood) of the engine compartment. Place the hood prop rod in the hole of hood hinge to secure the hood in the ...

  • Page 113

    In hot climates, the prop rod may be hot. Pick up the prop rod at the foam on the end of the prop rod. Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this w...

  • Page 114

    Lights multifunction lever the multifunction lever, located on the left side of the steering wheel, controls the operation of the headlights, headlight beam selection, passing light and turn signals. Note: the external lights can only be turned on with the ignition in the on/run position. Headlights...

  • Page 115

    High beams with the low beams activated, push the multi- function lever towards the instrument panel to turn on the high beams. Pull the multifunction lever toward the steering wheel to turn off the high beams. Flash-to-pass you can signal another vehicle with your headlights by lightly pulling the ...

  • Page 116

    Note: the indicators will automatically turn off when the turn has been completed and the steering wheel is returned to a straight position. Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatical...

  • Page 117

    Deactivation pull the multifunction lever toward the steering wheel and hold it for more than two seconds. Interior lights the interior light switches are located in the overhead console. The interior lights can be set to three different positions (off/left position, center position, on/right positi...

  • Page 118

    • when the doors are locked with the key fob the lights will turn off. Interior light timing (on/right position) • when all doors are closed a 15 minute timer is activated. Note: the timer is deactivated when the key is moved into the on/run position. Front fog lights — if equipped the fog light swi...

  • Page 119

    Windshield wipers and washers the windshield wiper/washer lever is located on the right side of the steering column. Note: the windshield wipers/washers will only oper- ate with the ignition in the on/run position. Front windshield wiper operation there are five different modes of operation for the ...

  • Page 120

    Note: the intermittent function only has one detent but wiper delay will vary with changes in vehicle speed. As vehicle speed increases the delay time will decrease. Low speed push the lever downward to the second detent. The wipers will operate at low speed. High speed push the lever downward to th...

  • Page 121

    Caution! (continued) • always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper control is turned off and the blades cannot return to the off position, damage to the wiper motor may occur. Rear windshield wiper rotate the...

  • Page 122

    Rear windshield washer operation push the windshield wiper/washer lever toward the instrument panel to activate the rear washer. Push and hold the lever for more than a half second and the wipers will activate automatically for three cycles after the lever is released. Tilt steering column — if equi...

  • Page 123

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Electronic speed control ...

  • Page 124

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 125

    To deactivate a soft tap on the brake pedal, pushing the canc button, or normal brake pressure while slowing the vehicle will deactivate electronic speed control without erasing the set speed memory. Pressing the on/off button or turning the ignition switch off erases the set speed memory. To resume...

  • Page 126

    Using electronic speed control on hills the transmission may downshift on hills to maintain the vehicle set speed. Note: the electronic speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. On steep hills, a greater speed loss or gain may occur so...

  • Page 127

    Corners of the rear fascia/bumper, depending on the location, type and orientation of the obstacle. If several obstacles are detected, the rear park assist system indicates the nearest obstacle. The minimum height of a detectable obstacle corresponds to the maximum height of an obstacle that would c...

  • Page 128

    Audible and visual signals supplied by the rear park assist system signal meaning indication obstacle distance an obstacle is present within the sensors’ field of view audible signal (dashboard loud- speaker) • sound pulses emitted at a rate that increases as the distance de- creases. • emits contin...

  • Page 129

    While audible signals are emitted, the audio system is not muted. The audible signal is turned off immediately if the distance increases. The tone cycle remains constant if the distance measured by the inner sensors is constant. If this condition occurs for the external sensors, the signal is turned...

  • Page 130

    Park assist system usage precautions note: • ensure that the outer surface and the underside of the rear bumper is clean and clear of snow, ice, mud, dirt or other obstruction to keep the rear park assist system operating properly. • jackhammers, large trucks, and other vibrations could affect the p...

  • Page 131

    Caution! (continued) • the vehicle must be driven slowly when using rear park assist in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using rear park assist. Warning! • drivers must be careful when backing up even wh...

  • Page 132

    Power sunroof — if equipped the power sunroof roof switch is located in the overhead console. Warning! • never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof s...

  • Page 133

    To open press and hold the power sunroof switch rearward for approximately one second and the sunroof will stop at the vented position. Press the switch a second time and hold for approximately one second and release, the sunroof will open fully, then stop automatically. This is called “express open...

  • Page 134

    Emergency operation in case of electrical failure the sunroof can be operated with the hex wrench that is located in the glove box. There is a plug located in the rear of the sunroof opening at the center of the vehicle. Removing the plug reveals a hex opening in the motor assembly of the sunroof. I...

  • Page 135

    Power is available when the ignition switch is in the on/run or start position. Insert the cigar lighter or accessory plug into the outlet for use. To preserve the heating element, do not hold the lighter in the heating position. Caution! • do not exceed the maximum power of 160 watts (13 amps) at 1...

  • Page 136

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 137

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 138

    Cupholders for the driver and front passenger, cupholders are lo- cated on the floor console between the front seats. For rear passengers, there are cupholders located on the floor between the front driver and passenger seats. Front cupholders rear cupholders 136 understanding the features of your v...

  • Page 139

    Storage glove box compartment the glove box is located on the right side of the instru- ment panel. Pull outward on the door latch to open the glove box. Push the glove box door upward to close it. Cargo area features the rear seatbacks have a fold down feature to allow increased cargo capacity. Pus...

  • Page 140

    Rear seat release buttons folded rear seats 138 understanding the features of your vehicle.

  • Page 141

    Rear window features rear window defroster the rear window defroster button is located in the center of the instrument panel, below the radio. Press this button to turn on the rear window defroster. An indicator in the button will illuminate when the rear window defroster is on. The rear window defr...

  • Page 143

    Understanding your instrument panel contents ! Instrument panel features . . . . . . . . . .143 ! Turbo boost gauge . . . . . . . . . . . . . . . . . .144 ! Instrument cluster . . . . . . . . . . . . . . . . .145 ! Instrument cluster descriptions . . . . .146 ! Electronic vehicle information center ...

  • Page 144

    ▫ quick guide . . . . . . . . . . . . . . . . . . . . . . . . .178 ▫ general information. . . . . . . . . . . . . . . . . . . .181 ▫ functions and adjustments . . . . . . . . . . . . . .183 ▫ radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .191 ▫ siriusxm satellite radio — if equippe...

  • Page 145

    Instrument panel features 1 — side vent 7 — passenger air bag 13 — storage compartment 2 — multifunction lever – light control 8 — glove compartment 14 — shift lever 3 — instrument cluster and warning lights 9 — rear defrost button 15 — sport button 4 — windshield wiper, washer, trip com- puter 10 —...

  • Page 146

    Turbo boost gauge your vehicle is equipped with a boost gauge and inte- grated shift light indicator located to the left of the instrument cluster. The boost gauge indicates the intake manifold pressure relative to barometric pressure. The engine management system in your vehicle intelligently regul...

  • Page 147

    Instrument cluster 4 understanding your instrument panel 145.

  • Page 148

    Instrument cluster descriptions 1. Glow plug light — if equipped the glow plug light will flash during engine oil viscosity sensor measurement in cold weather. During this measurement (up to 10 seconds), the starter will be disabled. If the measured oil viscosity is ok, the light will turn off and t...

  • Page 149

    Caution! (continued) • do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • keep all objects a safe distance from the window. 3. Front fog light indicator — if equipped this indicator will illuminate when the front fog lights are on. 4. Low fue...

  • Page 150

    Failure, external light failure, fuel cut-off intervention, fuel cut-off not available, parking sensor failure. 9. Air bag warning light this light will turn on for four seconds as a bulb check when the ignition switch is first turned to on/run. If the light is either not on during starting, stays o...

  • Page 151

    Vehicle is experiencing a problem with the charging system. Obtain service immediately. See an autho- rized studio. If jump starting is required, refer to “jump starting procedures” in “what to do in emergencies”. 13. Power steering system warning this light is used to manage the electrical warning ...

  • Page 152

    Vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) as an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (tpms) that illuminates a low tire pressure telltale when one or more of your ...

  • Page 153

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, t...

  • Page 154

    Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the mil after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations, the vehicle will drive normally and will not require to...

  • Page 155

    If the light turns on while driving, safely pull over and stop the vehicle. If the a/c system is on, turn it off. Also, shift the transmission into neutral and idle the ve- hicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “if...

  • Page 156

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 21. Electronic stability control off (esc off) indica- tor light this ligh...

  • Page 157

    If the abs light remains on or turns on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the brake warning light is not on. If the abs light is on, t...

  • Page 158

    26. Temperature gauge the temperature digital scale shows engine coolant tem- perature. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain gra...

  • Page 159

    As it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/ service,...

  • Page 160

    Electronic vehicle information center (evic) the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following: • system status • vehicle information warning message displays • personal settings (cus...

  • Page 161

    Press the down button to scroll downward through the displayed menu and the related options or to decrease the value displayed. Note: up and down buttons activate differ- ent functions according to the following situations: • to scroll the menu options upwards or downwards. • to increase or decrease...

  • Page 162

    • button volume • hill start • gsi shift up • daylights (d.R.L.) • exit menu selecting an option of the main menu without submenu 1. Briefly press the set esc button to select the main menu option to set. 2. Press the up or down button (by single presses) to select the new setting. 3. Briefly press ...

  • Page 163

    6. Press and hold the set esc button to return to the main menu (short hold) or the main screen (longer hold). Change engine oil indicator system change engine oil your vehicle is equipped with an engine oil change indicator system. The “change engine oil” message will flash in the evic display for ...

  • Page 164

    Trip button the trip button, located on the right steering column stalk, can be used to display and to reset the previously described values. • a short button press displays the different values. • a long button press resets the system and then starts a new trip. New trip to reset: • press and hold ...

  • Page 165

    Trip functions both trip functions are resettable (reset — start of new trip). “trip a” can be used to display the figures relating to: • range • trip distance a • average consumption a • instantaneous consumption • average speed a • travel time a (driving time). “trip b” can be used to display the ...

  • Page 166

    Note: the range depends on several factors: driving style, type of route (freeway, residential, mountain roads, etc.), conditions of use of the car (load, tire pressure, etc.). Trip planning must take into account the above notes. Distance traveled this value shows the distance covered since the las...

  • Page 167

    2. Briefly press the set esc button to go back to the menu screen or press and hold the set esc (approxi- mately one second) to go back to the main screen without storing settings. Speed beep (speed limit) with this function, it is possible to set the car speed limit (mph or km/h) to immediately ale...

  • Page 168

    2. Press the down button. “off” will flash on the display. 3. Briefly press the set esc button to go back to the menu screen, or press and hold the set esc button (approximately one second) to go back to the main screen without storing the settings. Trip b data (trip b on) through this option, it is...

  • Page 169

    4. When accessing the “time” sub-menu item, briefly press the set esc button and “hours” will flash on the display. 5. Press the up or down button for setting. 6. Briefly press the set esc button and “minutes” will flash on the display. 7. Press the up or down button for setting. Note: • the setting...

  • Page 170

    2. Press the up or down button for setting. 3. Briefly press the set esc button and “month” will flash on the display. 4. Press the up or down button for setting. 5. Briefly press the set esc button and “day” will flash on the display. 6. Press the up or down button for setting. Note: the setting wi...

  • Page 171

    If the radio has blue&me™, refer to the appropriate “blue&me™ user’s manual” for further information. Speed display when this function is activated the cluster will display the vehicle speed (mph or km/h). To activate (on) or to deactivate (off) the speed display feature, proceed as follows: 1. Brie...

  • Page 172

    Units (set units) this function may be used to set the measurement unit in three submenus: “distance,” “temperature” and “fuel economy.” to set the required unit, proceed as follows: 1. Briefly press the set esc button to display the three sub-menus. 2. Press the up or down button to navigate the th...

  • Page 173

    3. When accessing the “temperature” submenu: briefly press the set esc button. Either “°f” or “°c” will appear on the display (according to the previous setting). 4. Press the up or down button for setting. 5. Briefly press the set esc button to return to the sub-menu. When you have made the require...

  • Page 174

    To adjust the volume proceed as follows: 1. Briefly press the set esc button. The previously set volume “level” will flash on the display. 2. Press the up or down button for setting. 3. Briefly press the set esc button to go back to the menu screen, or press and hold the set esc button (approximatel...

  • Page 175

    Proceed as follows to switch this function on or off: 1. Briefly press the set esc button. “on” or “off” will flash on the display (according to previous setting). 2. Press the up or down button for setting. 3. Briefly press the set esc button to go back to the menu screen, or press and hold the but...

  • Page 176

    4. Briefly press the set esc button to go back to the menu screen, or press and hold the button (approxi- mately one second) to go back to the main screen without storing the settings. Exit menu this function closes the initial menu screen. Briefly press the set esc button to go back to the main scr...

  • Page 177

    If the radio has blue&me™, refer to the appropriate “blue&me™ user’s manual” for further information. The instructions for use are given below and we recom- mend you to read them carefully. Suggestions road safety please, learn how to use all different radio functions (e.G. Store stations) before be...

  • Page 178

    Cds the presence of dirt, scratches or distortions on the cds could cause skipping and poor sound quality while it is playing. For optimal playback conditions, follow these guidelines: • only use branded cds. • clean every cd thoroughly removing any finger marks or dust using a soft cloth. Hold cds ...

  • Page 179

    Copied is often shown in very small letters or is difficult to read on the actual cd cover where it may be, for example, “copy control”, “copy pro- tected”, “this cd cannot be played on a pc/mac”. • the cd player is capable of reading most compression systems currently in use, following the developm...

  • Page 180

    Quick guide radio controls button general functions mode on short button press off short button press tuner am, fm, sat (if equipped) source selection short repeated button press a-b-c cycles a, b, c presets for am, fm, sat (if equipped) short repeated button press media cd/aux/media player (if equi...

  • Page 181

    Button general functions mode audio audio adjustments: low tones (bass), high tones (treble), left/ right balance (balance), front/ rear balance (fader) menu activation: short button press adjustment type selection: press or adjustment of values: press or (information button) song, artist, album, ge...

  • Page 182

    Button general functions mode +vol/–vol volume adjustment press + button: volume increase press – button: volume decrease button radio functions mode radio station search: • automatic search • manual search automatic search: press buttons or (long press for fast for- ward) manual search: press butto...

  • Page 183

    Button cd functions mode cd ejection short button press previous/next track play short button press or cd track fast forward/rewind long button press or previous/next folder play (for cd- mp3) short button press or general information the radio offers the following functions: radio section • pll tun...

  • Page 184

    Cd section • track selection (forward/backward) • fast forward/rewind through tracks • cd display function: display of track number and on mp3 discs (song title, artist) and time elapsed since start of the track • playing audio cd, cd-r and cd-rw warning! On multimedia cds, besides audio tracks, the...

  • Page 185

    Audio section • mute/pause function • soft mute function • loudness function • graphic 7 band equalizer (if equipped) • separate bass/treble tone adjustment • right/left channel balancing • front/rear fader functions and adjustments turning the car radio on the car radio comes on when the (on/off) b...

  • Page 186

    Selecting the radio functions by pressing the tuner button briefly and repeatedly, the following audio sources can be selected cyclically: • am, fm and satellite bands (if equipped) selecting the cd function by briefly pressing the media button, the cd audio source can be selected (only if a cd is l...

  • Page 187

    Use the buttons or to scroll through the menu functions. To change the setting of the selected func- tion, use the or buttons. The current status of the selected function appears on the display. The functions managed by the audio menu are: • bass (bass adjustment) • treble (treble adjustment) • bala...

  • Page 188

    Balance adjustment proceed as follows: 1. Press audio button. 2. Press the or button to set “balance” in the audio menu. 3. Press the button to increase the sound from the left speakers or the button to increase the sound from the right speakers. By pressing the or buttons briefly, the levels will c...

  • Page 189

    Loudness function — if equipped the loudness function improves the volume of the sound while listening at low volumes, increasing the bass and treble. To activate/deactivate this function, select the “loud- ness” setting in the audio menu. The condition of the function (on or off) is shown on the di...

  • Page 190

    User eq settings function — if equipped to set a personalized equalizer adjustment: 1. Press audio button. 2. Use the or buttons to set eq function. 3. Use or buttons to select #eq user.# 4. Press menu button to start adjusting equalizer. 5. On the display a seven bar graph will appear, in which eac...

  • Page 191

    The functions managed by the menu are: • speech volume • aux audio offset • radio off • sat id • siriusxm telephone number • system reset • speed volume • on volume limit press the menu button again to exit the menu function. Speed volume function — if equipped this function automatically adapts the...

  • Page 192

    – if the volume level is between the minimum and maximum values, the radio will come on at the same volume as before it was switched off. – if the volume level is equal to or lower than the minimum value, the radio will come on at the minimum volume. • “on volume limit: off” – the radio will come on...

  • Page 193

    System reset function this function is used to restore all settings to the factory values. The options are: • no — no restore intervention. • yes — the default parameters will be restored. Dur- ing such operation, the wording “resetting” appears on the display. At the end of the operation, the sourc...

  • Page 194

    Preset buttons the buttons numbered from 1 to 5 are used to set the following pre-selections: • 15 in the fm band (5 in fma, 5 in fmb, 5 in fmc • 10 in the am band (5 in ama, 5 in amb) • 15 in sat (if so equipped) (5 sata, 5 satb, 5 satc) to listen to a preset station, select the desired frequency b...

  • Page 195

    Stereophonic broadcasters if the incoming signal is weak, the reproduction is automatically switched from stereo to mono. Siriusxm satellite radio — if equipped satellite radio antenna — if equipped the antenna for the satellite radio is mounted on the roof of the vehicle. Do not place items on the ...

  • Page 196

    Siriusxm satellite radio program types program types can be selected by pressing the or buttons. The program type will change to the next category and the radio will then tune to first station in that program type. Pressing or buttons will tune to only the stations in that program type. Pressing the...

  • Page 197

    Your service, either call the number listed on the display or visit the provider online. Caution! Neither sirius nor fiat is responsible for any errors in accuracies in the sirius data services or its use in vehicles. Siriusxm and all related marks and logos are trademarks of siriusxm radio inc. And...

  • Page 198

    Cd player introduction this chapter describes the operation of the cd player only. To operate the radio, refer to the description in the “functions and adjustments” chapter. Cd player selection to activate the cd player built into the equipment, proceed as follows: • load a cd with the equipment swi...

  • Page 199

    Press the button with the radio turned on, to activate the motorized cd ejection system. After ejec- tion, the last audio source listened to before playing the cd will be heard. If the cd is not removed from the radio, it will automati- cally be reloaded about 20 seconds later but will not resume pl...

  • Page 200

    If the track has been played for more than 3 seconds, pressing the button, starts the track again from the beginning. In this case, if you want to play the previous track, press the button twice consecu- tively. Track fast forward/rewind keep the button pressed down to fast forward the selected trac...

  • Page 201

    The specifications and operating conditions for playing mp3 files are the following: • the cd-roms used should be burned in accordance with iso standard 9660. • the music files should have the extension “.Mp3” or “.Wma” files with a different extension will not be reproduced. • the sampling frequenc...

  • Page 202

    When one of the id3-tag pieces of information is chosen to be displayed (title, artist, album) and this informa- tion has not been recorded for the track played, the text # unknown# will be displayed for that field. Selection of next/previous folder press the button to select a next folder or the bu...

  • Page 203

    Source can not be selected nothing has been loaded. Load the cd or the mp3 cd to be listened to. Cd player the cd does not play the cd is dirty. Clean the cd. The cd is scratched. Try using another cd. The cd can not be loaded a cd is already loaded. Press the button and remove the cd. Mp3 file read...

  • Page 204

    Ipod®/usb/media player control — if equipped this feature allows an ipod® or external usb device to be plugged into the usb port, located in the glove compart- ment. Refer to the appropriate blue&me™ radio user’s manual for ipod® or external usb device support capability. 1 — ipod® or external usb d...

  • Page 205

    Steering wheel audio controls the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pr...

  • Page 206

    Radio operation pressing the top of the switch will “seek” up for the next listenable station and pressing the bottom of the switch will “seek” down for the next listenable station. The button located in the center of the left-hand control will tune to the next preset station that you have pro- gram...

  • Page 207

    5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. Note: if you experience difficulty in playing a particular disc, it may be damaged (i.E., scratched, reflective coating removed, a hair, moistur...

  • Page 208

    Manual heating and air conditioning the manual climate controls consist of a series of rotary dials and one inner push knob. 1. Temperature control rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial to the left into the blue area of the sca...

  • Page 209

    Note: • continuous use of the recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. • the use of the recirculation mode in cold or damp weather could cause windows to fog on the inside, because of moisture buildup inside the veh...

  • Page 210

    Require extra heat to the windshield. This setting is good for maintaining comfort while reducing mois- ture on the windshield. • defrost air is directed through the windshield and side window demister outlets. Use this mode with maximum blower and temperature settings for best windshield and side w...

  • Page 211

    Operating tips chart 4 understanding your instrument panel 209.

  • Page 212

    Automatic temperature control (atc) — if equipped • the automatic temperature control (atc) allows the driver to select individual comfort settings. • the system provides set-and-forget operation for op- timum comfort and convenience. • the system can be controlled manually, if desired. The atc syst...

  • Page 213

    2. A/c button press and release to change the current air conditioning (a/c) setting. Performing this function will cause the atc to switch into manual mode. 3. Temperature control up button provides temperature up control. Push the button for warmer temperature settings. 4. Blower control up button...

  • Page 214

    Note: the center instrument panel outlets can be aimed so that they are directed toward the rear seat passengers for maximum airflow to the rear. 9. Blower control down button there are 12 blower speeds. The blower speed decreases as you press this button. Performing this function will cause the atc...

  • Page 215

    3. When the system is set up for your comfort level, it is not necessary to change the settings. You will experi- ence the greatest efficiency by simply allowing the system to function automatically. Note: • it is not necessary to move the temperature settings for cold or hot vehicles. The system au...

  • Page 216

    Blower control there are 12 fixed blower speeds. Use the blower control up or down buttons to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you press or hold the blower control up button and decreases when you press or hold the blower cont...

  • Page 217

    Floor mode air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Bi-level air is directed through the panel and floor outlets. Press and release the panel mode button and floor mode button to enter bi-level mode, the indicators ill...

  • Page 218

    Air conditioning (a/c) the air conditioning (a/c) button allows the operator to manually activate or deactivate the air conditioning system. When in a/c mode with the atc set to a cool temperature, dehumidified air flows through the air outlets. If economy mode is desired, press the a/c button to tu...

  • Page 219

    Operating tips chart 4 understanding your instrument panel 217.

  • Page 220

    Window fogging windows will fog on the inside when the humidity inside the vehicle is high. This often occurs in mild or cool temperatures when it’s rainy or humid. In most cases, turning the air conditioning (pressing the a/c button) on will clear the fog. Adjust the temperature control, air direct...

  • Page 221

    Vacation storage anytime you store your vehicle, or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air using the high blower setting. This will ensure adequate system lubrication to minimize the possibility o...

  • Page 223

    Starting and operating contents ! Starting procedures . . . . . . . . . . . . . . . .224 ▫ manual transmission . . . . . . . . . . . . . . . . . . .224 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .224 ▫ cold weather operation . . . . . . . . . . . . . . . .225 ▫ extended park starti...

  • Page 224

    ! Sport mode . . . . . . . . . . . . . . . . . . . . . . . . .236 ! Brake system . . . . . . . . . . . . . . . . . . . . . . .237 ▫ four-wheel anti-lock brake system (abs) . . .237 ! Electronic brake control system . . . .238 ▫ anti-lock brake system (abs) . . . . . . . . . . . .239 ▫ brake assist s...

  • Page 225

    ▫ tire spinning . . . . . . . . . . . . . . . . . . . . . . . .261 ▫ tread wear indicators . . . . . . . . . . . . . . . . . .261 ▫ life of tire . . . . . . . . . . . . . . . . . . . . . . . . .262 ▫ replacement tires . . . . . . . . . . . . . . . . . . . . .263 ! Tire chains (traction devices) . . ...

  • Page 226

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a numb...

  • Page 227

    Cold weather operation to prevent possible engine damage while starting at low temperatures, this vehicle will inhibit engine cranking when the ambient temperature is less than –22° f (–30° c) and the oil temperature sensor reading indicates an engine block heater has not been used. An externally- p...

  • Page 228

    3. If the engine fails to start within 10 seconds, turn the ignition switch to the stop (off/lock) position, wait 5 seconds to allow the starter to cool, then repeat the “extended park starting” procedure. 4. If the engine fails to start after 8 attempts, allow the starter to cool for at least 60 se...

  • Page 229

    Shut off to circulate coolant through the turbocharger. Although the pump is rubber-mounted for quiet opera- tion, it is normal to hear it running during this time. Manual transmission five-speed manual transmission warning! You or others could be injured if you leave the vehicle unattended without ...

  • Page 230

    Use each gear in numerical order; do not skip a gear. Be sure the transmission is in first gear, not third, when starting from a standing position. Damage to the clutch can result from starting in third gear. For most city driving, you will find it easier to use only the lower gears. For steady high...

  • Page 231

    Downshifting proper downshifting will improve fuel economy and prolong engine life. Caution! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released. Damage...

  • Page 232

    Warning! (continued) and possibly have a collision. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet, mud, loose sand, etc.). Traction when driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. T...

  • Page 233

    Warning! (continued) furthermore, flowing and/or rising water can carry your vehicle away swiftly. Failure to follow this warning may result in injuries that are serious or fatal to you, your passengers, and others around you. Shallow standing water although your vehicle is capable of driving throug...

  • Page 234

    Caution! (continued) • getting water inside your vehicle’s engine can cause it to lock up and stall out, and cause serious internal damage to the engine. Such damage is not covered by the new vehicle limited warranty. Warning! • driving through standing water limits your vehi- cle’s traction capabil...

  • Page 235

    Warning! Continued operation with reduced or no power steer- ing assist could pose a safety risk to yourself and others. Service should be obtained as soon as pos- sible. If the steering icon is flashing, it indicates that the vehicle needs to be taken to an authorized studio for service. It is like...

  • Page 236

    Parking brake before leaving the vehicle, make sure that the parking brake is fully applied. Also, be certain to leave manual transmission in reverse or first gear. The parking brake lever is located in the center console. To apply the parking brake, pull the lever up as firmly as possible. To relea...

  • Page 237

    Should always be applied whenever the driver is not in the vehicle. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injur...

  • Page 238

    Sport mode in sport mode, the engine is more responsive to the throttle pedal, and provides more maximum torque by increasing turbo boost pressure. Steering feedback is improved, and steering effort is slightly higher. This driving mode is useful for spirited driving. 1. To activate the sport mode, ...

  • Page 239

    Brake system in the event power assist is lost for any reason (for example; repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be significantly more than that required with the power system operating. If either of the two h...

  • Page 240

    Warning! • pumping the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • the anti-lock brake system (abs) cannot prevent the natural laws of physics f...

  • Page 241

    Anti-lock brake system (abs) this system aids the driver in maintaining vehicle control under adverse braking conditions. The system controls hydraulic brake pressure to prevent wheel lockup and help avoid skidding on slippery surfaces during braking. Refer to “four-wheel anti-lock brake system” in ...

  • Page 242

    Traction control system (tcs) this system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the tcs system functions si...

  • Page 243

    Warning! There may be situations on minor hills (i.E., less than 2.5%), with a loaded vehicle, or while pulling a trailer, when the system will not activate and slight rolling may occur. This could cause a collision with another vehicle or object. Always remember the driver is responsible for brakin...

  • Page 244

    Note: the esc off switch is located left of the steering column. Warning! The electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esc cannot prevent all accidents, includi...

  • Page 245

    Esc operating modes the esc system has three available operating modes. Full on this is the normal operating mode for esc. Whenever the vehicle is started, the esc system will be in on mode. This mode should be used for most driving situations. Esc should only be turned to partial off for specific r...

  • Page 246

    Off switch for five seconds. After five seconds, the esc off indicator light will illuminate, and the “esc off” message will display in the evic. To turn esc on again, momentarily press the esc off switch. Warning! In the esc “full off” mode, the engine torque reduction and stability features are ca...

  • Page 247

    Note: • the esc activation/malfunction indicator light and the esc off indicator light come on momentarily each time the ignition switch is turned on. • each time the ignition is turned on, the esc system will be on even if it was turned off previously. The esc off indicator light indicates the elec...

  • Page 248

    Note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standards. Tires designed to this standard ha...

  • Page 249

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards $ ....Blank....$ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t or s = temporary spare tire 31 = overall diameter in inches (in) 215...

  • Page 250

    Example: r = construction code — #r# means radial construction — #d# means diagonal or bias construction 15 = rim diameter in inches (in) service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of spee...

  • Page 251

    Example: load identification: $ ....Blank....$ = absence of any text on the sidewall of the tire indicates a standard load (sl) tire extra load (xl) = extra load (or reinforced) tire light load (ll) = light load tire c, d, e, f, g = load range associated with the maximum load a tire can carry at a s...

  • Page 252

    Example: dot ma l9 abcd 0301 dot = department of transportation — this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 253

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 254

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar. Tire and loading information placard tire placard location tire and loading information placard 252 starting and operating.

  • Page 255

    This placard tells you important information about the: 1) number of people that can be carried in the ve- hicle. 2) total weight your vehicle can carry. 3) tire size designed for your vehicle. 4) cold tire inflation pressures for the front, rear, and spare tires. Loading the vehicle maximum load on...

  • Page 256

    2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and pas- sengers from xxx lbs or xxx kg. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amou...

  • Page 257

    5 starting and operating 255.

  • Page 258

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 259

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns t...

  • Page 260

    Defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three hour period. The cold tire inflation pressure must not exceed the maximum inflation pres- sure molded into the tire sidewall. Check tire pressures more often...

  • Page 261

    Warning! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious collision. Do not drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Radial ply tires warning! ...

  • Page 262

    All season tires – if equipped all season tires provide traction for all seasons (spring, summer, fall and winter). Traction levels may vary be- tween different all season tires. All season tires can be identified by the m+s, m&s, m/s or ms designation on the tire sidewall. Use all season tires only...

  • Page 263

    Sidewall. Use summer tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Spare tire matching original equipped tire and wheel – if equipped your vehicle may be equipped with a spare tire and wheel equivalent in look and function to the original ...

  • Page 264

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further infor- mation. Life of t...

  • Page 265

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with...

  • Page 266

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 267

    Tire chains (traction devices) due to limited clearance, tire chains or traction devices are not recommended. Caution! Damage to the vehicle may result if tire chains are used. Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform differ...

  • Page 268

    The suggested rotation method is the “rearward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed. Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure b...

  • Page 269

    Also increase as the vehicle is driven - this is normal and there should be no adjustment for this increased pres- sure. The tpms will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning limit for any reason, including low temperature effects, or natural ...

  • Page 270

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, ...

  • Page 271

    • seasonal temperature changes will affect tire pressure, and the tpms will monitor the actual tire pressure in the tire. Base system this is the tpms warning indicator located in the instrument cluster. The tpms uses wireless technology with wheel rim mounted electronic sensors to monitor tire pres...

  • Page 272

    Vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. Check tpms warnings the tire pressure monitoring telltale light will flash on and off for 75 seconds and remain on solid when a system fault is detected, and the “tire pressure monitoring unavailab...

  • Page 273

    Monitoring telltale light will flash on and off for 75 seconds and then remain on solid and the #tire pressure monitoring unavailable# message will be displayed. 4. For each subsequent ignition key cycle, a chime will sound and the tire pressure monitoring telltale light will flash on and off for 75...

  • Page 274

    The tire pressure sensors are covered under one of the following licenses: united states mrxc4w4ma4 canada 2546a-c4w4ma4 (single) fuel requirements this engine is designed to meet all emis- sion regulations and provide satisfactory fuel economy and performance when us- ing high-quality unleaded “reg...

  • Page 275

    The manufacturer supports the use of reformulated gaso- lines. Properly blended reformulated gasolines will pro- vide excellent performance and durability of engine and fuel system components. Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol...

  • Page 276

    To fix a non-ffv vehicle inadvertently fueled once with e-85 perform the following: • drain the fuel tank (see your authorized studio.) • change the engine oil and oil filter. • disconnect and reconnect the battery to reset the engine controller memory. More extensive repairs will be required for pr...

  • Page 277

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gas is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance and damage the emissions control system. • an out-of-tune engine or certain fuel or ignition malfu...

  • Page 278

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 279

    Adding fuel fuel filler cap (gas cap) the gas cap is located on the passenger side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle. Caution! • damage to the fuel system or emission control system could result from using an improper f...

  • Page 280

    Warning! • never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • never add fuel when the engine is running. It may cause the mil to turn on and could cause a fire. • a fire may result if gasoline is pumped into a portable container tha...

  • Page 281

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmission flat tow none transmission in neutral dolly tow front ok rear not allowed on trailer all ok note: vehicles equipped with manual transmissions may be recr...

  • Page 283

    What to do in emergencies contents ! Hazard warning flashers . . . . . . . . . . .282 ! If your engine overheats . . . . . . . . . . . .282 ! Tirefit kit — if equipped . . . . . . . . . . . . .283 ▫ tirefit storage . . . . . . . . . . . . . . . . . . . . . .284 ▫ tirefit kit components and operation...

  • Page 284

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the radio. Press the switch to turn on the hazard warning flashers. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Press th...

  • Page 285

    Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the n...

  • Page 286

    Tirefit storage the tirefit kit is located under the front driver’s seat. Tirefit kit components and operation 1. Sealant bottle 2. Deflation button 3. Pressure gauge tirefit kit location tirefit components 284 what to do in emergencies.

  • Page 287

    4. Power button 5. Mode select knob 6. Sealant hose (clear) 7. Air pump hose (black) 8. Power plug tirefit usage precautions • using the tirefit sealant may cause the tire pressure monitoring system (tpms) to become inoperable. It is recommended that you take your vehicle to your local studio to hav...

  • Page 288

    Air mode when inflating such items to avoid injecting sealant into them. The tirefit sealant is only in- tended to seal punctures less than ¼ in (6 mm) diameter in the tread of your vehicle. • do not lift or carry the tirefit kit by the hoses. Warning! • do not attempt to seal a tire on the side of ...

  • Page 289

    Warning! (continued) • take care not to allow the contents of tirefit to come in contact with hair, eyes, or clothing. Tire- fit is harmful if inhaled, swallowed, or absorbed through the skin. It causes skin, eye, and respira- tory irritation. Flush immediately with plenty of water if there is any c...

  • Page 290

    (b) setting up to use tirefit: 1. Turn the mode select knob (5) to the sealant mode position. 2. Uncoil the sealant hose (6) and then remove the cap from the fitting at the end of the hose. 3. Place the tirefit kit flat on the ground next to the deflated tire. 4. Remove the cap from the valve stem a...

  • Page 291

    The sealant hose (6) to the valve stem. Check that the mode select knob (5) is in the sealant mode position and not air mode. Press the power button (4) to turn on the tirefit kit. 2. Connect the power plug (8) to a different 12 volt power outlet in your vehicle or another vehicle, if available. Mak...

  • Page 292

    If the tire does not inflate to at least 26 psi (1.8 bar) pressure within 15 minutes: • the tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. Note: if the tire becomes over-inflated, press the defla- tion button to reduce the tire pressure to the recom- men...

  • Page 293

    Warning! Tirefit is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after using tirefit. Do not exceed 55 mph (88 km/h) until the tire is repaired or replaced. Failure to follow this warning can result in injuries that are serious or fatal to you, your passengers, ...

  • Page 294

    2. Disconnect the tirefit kit from the valve stem, reinstall the cap on the valve stem and unplug from 12 volt outlet. 3. Place the tirefit kit in its proper storage area in the vehicle. 4. Have the tire inspected and repaired or replaced at the earliest opportunity at an authorized studio or tire s...

  • Page 295

    6. Verify that the cap is installed on the fitting at the end of the sealant hose (6) and return the hose to its storage area (located on the bottom of the air pump). 7. Return the tirefit kit to its storage location in the vehicle. Jacking and tire changing — if equipped warning! • do not attempt t...

  • Page 296

    Jack location the jack and jack wrench tool are stowed in a bag under the front driver’s seat. Preparations for jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far e...

  • Page 297

    5. Turn off the ignition. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the right front tire, block the left rear wheel. Note: passengers should not remain in the vehicle while the vehicle is being jacked. Jacking instructions warning! ...

  • Page 298

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 299

    2. Loosen, but do not remove, the wheel bolts by turning them to the left one turn while the wheel is still on the ground. Note: there are front and rear jacking locations on each side of the body (as indicated by the triangular lift point symbol on the sill molding). Do not raise the vehicle until ...

  • Page 300

    3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed. Warning! Raising the vehicle higher than necessary ...

  • Page 301

    Warning! To avoid the risk of forcing the vehicle off the jack, do not fully tighten the wheel bolts until the vehicle has been lowered. Failure to follow this warning may result in personal injury. 6. Install the wheel and wheel bolts with the cone shaped end of the bolts toward the wheel. Lightly ...

  • Page 302

    Note: when using a portable battery booster pack, follow the manufacturer’s operating instructions and precautions. Warning! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Caution! Do not use a portable battery booster pack or any other ...

  • Page 303

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 304

    Jump-starting procedure warning! Failure to follow this procedure could result in per- sonal injury or property damage due to battery ex- plosion. Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1. Connect th...

  • Page 305

    5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. Once the engine is started, remove the jumper cables in the reverse sequence: 6. Disconnect the negative (-) jumper cable from the...

  • Page 306

    Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Then shift back and forth between 2nd gear and reverse while gently pressing the accelerator. Us...

  • Page 307

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously w...

  • Page 308

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members ...

  • Page 309

    Maintaining your vehicle contents ! Engine compartment — 1.4l turbo . . . .309 ! Onboard diagnostic system — obd ii . .310 ! Emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . . . .310 ! Replacement parts . . . . . . . . . . . . . . . . . .312 ! Studio servic...

  • Page 310

    ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .336 ! Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .342 ▫ interior fuses . . . . . . . . . . . . . . . . . . . . . . . .342 ▫ underhood fuses. . . . . . . . . . . . . . . . . . . ....

  • Page 311

    Engine compartment — 1.4l turbo 1 — engine coolant reservoir 5 — battery 2 — engine oil dipstick 6 — engine oil fill 3 — brake fluid reservoir 7 — washer fluid reservoir 4 — front distribution unit (fuses) 7 maintaining your vehicle 309.

  • Page 312

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 313

    Indicator light (mil)” is functioning and is not on when the engine is running, and that the obd ii system is ready for testing. Normally, the obd ii system will be ready. The obd ii system may not be ready if your vehicle was recently serviced, recently had a dead battery or a battery replace- ment...

  • Page 314

    You may need to do nothing more than drive your vehicle as you normally would in order for your obd ii system to update. A recheck with the above test routine may then indicate that the system is now ready. Regardless of whether your vehicle’s obd ii system is ready or not, if the mil is illuminated...

  • Page 315

    Maintenance procedures the pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed maintenance schedule, there are other components which may require servicing or replacement in the futu...

  • Page 316

    Fully warmed engine is shut off. Do not check oil level before starting the engine after it has sat overnight. Checking engine oil level when the engine is cold will give you an incorrect reading. Checking the oil while the vehicle is on level ground, and about five minutes after a fully warmed engi...

  • Page 317

    Engine oil selection for best performance and maximum protection for tur- bocharged engines under all types of operating condi- tions, the manufacturer recommends synthetic engine oils that are api certified and meet the requirements of chrysler material standard ms-12991. Engine oil viscosity (sae ...

  • Page 318

    Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection this manufacturer’s engines have a full-flow type dispos- able oil filter. Use a filter of this type for replacement. The quality of replacement filters varies conside...

  • Page 319

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 320

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be ...

  • Page 321

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 322

    1. Remove the t20 torx screw that secures the passenger side console closeout cover. 2. Pull the console closeout cover rearward to disengage the front retaining tab and remove the cover. 3. Remove the two 5.5mm screws (1 and 2) that secure the particulate air filter cover to the hvac housing. T20 t...

  • Page 323

    4. Remove the a/c air filter by pulling it straight out of the housing. Take note of the air filter position indica- tors. 5. Install the a/c air filter with the air filter position indicators pointing in the same direction as removal. A/c air filter 7 maintaining your vehicle 321.

  • Page 324

    Caution! The a/c air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 6. Install the passenger side console closeout. Refer to the “maintenance schedule” for the proper mainte...

  • Page 325

    Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact...

  • Page 326

    3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder. 4. Install the wiper blade pivot pin into the wiper blade holder at the end of the wiper arm, and firmly press the wiper blade until it snaps into place. 5. Lower the wiper blade an...

  • Page 327

    Warning! (continued) must be exercised when filling or working around the washer solution. Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhau...

  • Page 328

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine perfor- mance and cause serious damage to the engine. • damage to the catalytic converter can res...

  • Page 329

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires di...

  • Page 330

    Coolant checks check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh engine coolant (anti- freeze). Check...

  • Page 331

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 332

    You use the same engine coolant (oat coolant conform- ing to ms-12106) throughout the life of your vehicle. Please review these recommendations for using organic additive technology (oat) engine coolant (antifreeze) that meets the requirements of chrysler material stan- dard ms-12106. When adding en...

  • Page 333

    The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loo...

  • Page 334

    As long as the engine operating temperature is satisfac- tory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicl...

  • Page 335

    • keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • do not change the thermostat for summer or winter operation. If replacement is ever necessary, install only the correct type thermostat. Other designs may result in uns...

  • Page 336

    When the pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Note: if your vehicle is equipped with a manual trans- mission , the brake fluid reservoir supplies fluid to both the brake system and the clutch release system. The two systems are separated in...

  • Page 337

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 338

    Manual transmission lubricant selection use only the manufacturers recommended transmission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Fluid level check check the fluid level by removing the fill plug. The fluid level should be betw...

  • Page 339

    What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road salt, dirt and moisture accumulation. • stone and gravel impact. • insects, tree sap and tar. • salt in the air near seacoast localities. ...

  • Page 340

    Special care • if you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • it is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open. • if you detect any stone chips or scratches...

  • Page 341

    Caution! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel’s protective finish. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheel’s pro- tective finish. Only mopar® whee...

  • Page 342

    Can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and mopar® total clean. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, c...

  • Page 343

    When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Instrument panel cover the instrument panel cover has a low glare surface which minimizes reflections on the windshield. Do not use protectants or other products whi...

  • Page 344

    Seat belt maintenance do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the car to wash them. Dry ...

  • Page 345

    Cavity vehicle fuse number mini fuse description 1 f12 7.5 amp brown right low beam 2 f32 5 amp tan front and rear ceiling lights trunk and door courtesy lights 3 f53 5 amp tan instrument panel node 4 f38 20 amp yellow central door locking 5 f36 10 amp red diagnostic socket, car radio, climate contr...

  • Page 346

    Cavity vehicle fuse number mini fuse description 10 f51 5 amp tan car radio switch, climate control system, stop light, clutch 11 f37 5 amp tan stop light switch, instrument panel node 12 f49 5 amp tan exterior mirror, gps, electric mirror, parking sen- sor 13 f31 5 amp tan ignition, climate control...

  • Page 347

    Underhood fuses the front distribution unit is located on the right side of the engine compartment, next to the battery. To access the fuses, press the release tabs and remove the cover. The id number of the electrical component correspond- ing to each fuse can be found on the back of the cover. Fro...

  • Page 348

    Cavity maxi fuse mini fuse description f01 60 amp blue body controller f02 20 amp yellow audio amplifier f03 20 amp yellow ignition switch f04 40 amp orange anti-lock brake pump f05 70 amp tan electric power steering f06 20 amp yellow radiator fan - single speed f06 30 amp green radiator fan - low s...

  • Page 349

    Cavity maxi fuse mini fuse description f16 7.5 amp brown transmission f17 25 amp white powertrain (multiair – if equipped) f17 15 amp blue powertrain f18 15 amp blue powertrain f18 5 amp tan powertrain (multiair – if equipped) f19 7.5 amp brown air conditioning f20 15 amp blue heated seats – if equi...

  • Page 350

    Cavity maxi fuse mini fuse description f87 5 amp tan lights f90 5 amp tan heated mirrors vehicle storage if you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • disconnect the negative cable from the battery. • anytime you store your...

  • Page 351

    Exterior bulbs bulb number front low and high beam headlamp hir2 front parking/daytime running lamps w21/5w front fog lamps h11 front side marker lamps w3w front turn signal lamps wy21w side direction lamps w5w rear turn signal lamps py21w rear side marker lamps w3w rear tail and stop lamps py21w/5w...

  • Page 352

    Headlamps low beam and high beam 1. Remove the plastic cap from the back of the headlamp housing. 2. Rotate the bulb counter-clockwise. 3. Remove the bulb and replace as needed. 4. Install the bulb and rotate clockwise to lock in place. 5. Reinstall the plastic cap. Front turn signal, parking and da...

  • Page 353

    6. Install the bulb into socket, and rotate bulb/socket clockwise into lamp locking it in place. 7. Reinstall the plastic cap. Front fog lamps to replace the front fog lights, see your authorized studio. Front/rear side marker lamps 1. Remove portion of the wheel liner to allow hand access to side m...

  • Page 354

    Rear tail, stop, backup and turn signal lamps 1. Open the liftgate. 2. Remove the two screws and remove the tail lamp assembly. 3. Remove the four screws (using a t20 driver) and separate the backplate from the lamp housing. 4. Remove the tail, stop, or turn signal bulbs by pushing them slightly and...

  • Page 355

    Fluid capacities u.S. Metric fuel (approximate) 10.5 gallons 40 liters engine oil with filter 1.4 liter turbo engine 4 quarts 3.8 liters cooling system 1.4 liter turbo engine (mopar® antifreeze/engine coolant 10 year/150,000 mile formula) 4.6 quarts 4.4 liters fluids, lubricants and genuine parts en...

  • Page 356

    Component fluid, lubricant, or genuine part engine oil we recommend you use api certified sae 5w-40 full synthetic engine oil, meeting the requirements of chrysler material standard ms-12991. Refer to your engine oil filler cap for correct sae grade. Engine oil filter we recommend you use a mopar® e...

  • Page 357

    Maintenance schedules contents ! Maintenance schedule . . . . . . . . . . . . .356 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .358 8.

  • Page 358

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 359

    Required maintenance intervals . Refer to the maintenance schedules on the following pages for required maintenance. At every oil change interval as indicated by oil change indicator system: • change oil and filter. • rotate the tires. Rotate at the first sign of irregu- lar wear, even if it occurs ...

  • Page 360

    Maintenance chart mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,0...

  • Page 361

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 362

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 363

    If you need consumer assistance contents ! Suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .362 ▫ prepare for the appointment. . . . . . . . . . . . .362 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .362 ▫ be reasonable with requests ....

  • Page 364

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 365

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized studio service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 366

    Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by bell canada. For tty teletypewriter users, dial 711 and for voice callers, dial 1 800 855-0511 to connect with a bell relay service operator. Service contract you may have purchase...

  • Page 367

    Warning! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the state of california to cause cancer and birth defects, or other reproductive harm. In addi- tion, certain fluids contained in vehicles and certain products of component wear con...

  • Page 368

    To contact nhtsa, you may either call the auto safety hotline toll free at 1–888–327–4236 (tty: 1–800–424– 9153), or go to http://www.Safercar.Gov; or write to: administra- tor, nhtsa, 1200 new jersey avenue, se., west building, washington, d.C. 20590. You can also obtain other infor- mation about m...

  • Page 369

    Diagnostic procedure manuals diagnostic procedure manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and cor...

  • Page 370

    All passenger car tires must conform to federal safety requirements in addition to these grades. Treadwear the treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 wou...

  • Page 371

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 373

    Index 10

  • Page 374

    Adding engine coolant (antifreeze) . . . . . . . . . . . .329 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .277 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .324 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .274 airbag. . . . . . . . . ....

  • Page 375

    Brake, parking . . . . . . . . . . . . . . . . . . . . . . . . . . .234 brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .333 brake system . . . . . . . . . . . . . . . . . . . . . . . . . . . .237 anti-lock (abs) . . . . . . . . . . . . . . . . . . . . . . . .237 master cylind...

  • Page 376

    Coolant (antifreeze) . . . . . . . . . . . . . . . . . . . . . . .353 cooling system. . . . . . . . . . . . . . . . . . . . . . . . . . .327 adding coolant (antifreeze) . . . . . . . . . . . . . . .329 coolant level . . . . . . . . . . . . . . . . . . . . . . . . . .328 disposal of used coolant . . ...

  • Page 377

    Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . .299 towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .305 emission control system maintenance . . . . . . . . . .310 engine air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .316 break-in recommendations ....

  • Page 378

    Fluids, lubricants and genuine parts . . . . . . . . . . .353 fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116 freeing a stuck vehicle . . . . . . . . . . . . . . . . . . . . .304 fuel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .272 adding . . . . . ....

  • Page 379

    Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .340 high beam . . . . . . . . . . . . . . . . . . . . . . . . . . . .147 switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 heated mirrors. . . . . . . . . . . . . . . . . . . . . . . . . . . .95 heated seats. . ....

  • Page 380

    Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 lead free gasoline . . . . . . . . . . . . . . . . . . . . . . . .272 leaks, fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262 liftgate...

  • Page 381

    Maintenance free battery. . . . . . . . . . . . . . . . . . . .317 maintenance, general . . . . . . . . . . . . . . . . . . . . . .313 maintenance procedures . . . . . . . . . . . . . . . . . . . .313 maintenance schedule . . . . . . . . . . . . . . . . . . . . . .356 malfunction indicator light (ch...

  • Page 382

    Onboard diagnostic system . . . . . . . . . . . . . . . . . .310 operating precautions . . . . . . . . . . . . . . . . . . . . . .310 operator manual (owner’s manual) . . . . . . . . . . . . .5 overheating, engine . . . . . . . . . . . . . . . . . . . . . . .282 owner’s manual (operator manual) . . ...

  • Page 383

    Remote sound system (radio) controls . . . . . . . . .203 replacement bulbs . . . . . . . . . . . . . . . . . . . . . . . .348 replacement keys . . . . . . . . . . . . . . . . . . . . . . . . .14 replacement parts. . . . . . . . . . . . . . . . . . . . . . . . .312 replacement tires . . . . . . . . ...

  • Page 384

    Shoulder belts . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 side airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 signals, turn . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 snow chains (tire chains). . . . . . . . . . . . . . . . . . .265 snow tires . ...

  • Page 385

    Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .293 general information . . . . . . . . . . . . . . . . . . . . .256 high speed . . . . . . . . . . . . . . . . . . . . . . . . . . .258 inflation pressures . . . . . . . . . . . . . . . . . . . . . . .257 jacking . . . . . . . . . . ...

  • Page 386

    Universal consumer interface (uci) connector . . . .202 unleaded gasoline . . . . . . . . . . . . . . . . . . . . . . . .272 untwisting procedure, seat belt . . . . . . . . . . . . . . . .34 vehicle identification number (vin) . . . . . . . . . . . . .7 vehicle loading . . . . . . . . . . . . . . . ...

  • Page 387

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 388

    Fiat 500 abarth chrysler group llc o w n e r ’ s m a n u a l 2 0 1 3 2013 fia t 500 abar th 13fx24-126-ae fifth edition rev 1 printed in u.S.A..