1. DL manuals
  2. Galanz
  3. Washer
  4. XQG60-A708E
  5. Service Manual

Galanz XQG60-A708E Service Manual

Summary of XQG60-A708E

  • Page 1

    Service manual of 6.0kg front loading washing machine please carefully read this manual before service, judge fault in order to work on the repairs. Suitable model number: models xqg60-a708e.

  • Page 2

    1 contents 1 ． safety notices---------------------------------------------------------------------------------------2 2 ． parts name -------------------------------------------------------------------------------------------3 3 ． installation ---------------------------------------------------------...

  • Page 3

    2 adjusted, specific to the washing machine practical parameters or product instruction 1 ． safety notices in order to avoid harm or injure user and other’s life and property, the follow instructions about safety should be seriously obeyed: ignore the content. When wrong to use, use the following ma...

  • Page 4

    3 attention ● list as below may cause damage\deformation\collision. ⒉remove all the water in the washer to avoid freezing. Do not climb or leave heavy things on the washer. ⒉two persons are needed to move the washer. Bolts must be installed in advance before moving. ⒉the water should below 95 ℃ when...

  • Page 5

    4 3 ． installation 3.1 、remove all outer package, including the foam base, check if the machine is intact.Water drops may appear on the packing plastic bag and the glass of the observation window occasionally, they are condensation resulted from water testing before the product leaves the factory. I...

  • Page 6

    5 3.2.2 、inspection operation ① plugged in plug, connect inlet hose ②press power supple ③press “start/pause” ④confirm inflow water ⑤confirm automatic corotation and reverse ⑥close power, open power again, choose dewatering, then press”start/pause”. ⑦confirm drain away water and dewatering ⑨close pow...

  • Page 7

    6 1. Program knob 2. Temperature 3. Start/pause 4.Power 4 ．electrical diagrams circuit diagram.

  • Page 8

    7 5． error indication & analysis.

  • Page 9

    8 5.1 error indication. No. Error code checking/reason settlement 1 flooding water error ● ● ◎ （e1） ◆is thewater tap opening or water floe too slow? ◆ does the sensor pressure air leakage? ◆ is the inlet valve blocked by something? ◆pcb error。 1 、check the water tap close or open and the water flow ...

  • Page 10

    9 attention：1、●—indicate the light is off；◎—indicate the light is flicking 2 、when the error occurs,all led light are flickering except indicator light on the control panel. Those indicator lights can judge what kind of error by washing ,rinsing and drycleaning 5.2 self-examine mode press【k1】 + 【k2】...

  • Page 11

    10 attention ：during the detection, for example: the failure occurs in the process of measurement, the machine will not conduct the following programs unless the problem has been solved and proceed the detection function again, it can finish all the detection function. During the detection ，press bu...

  • Page 12

    11 3 ①remove the inlet hose and clip 4 ①remove the inlet hose(picture 4) picture ４ inlet valve 1 ①take of the inlet valve connection ②remove two bolts from the back of the inlet valve ③remove the hose clip and hose down frame 1 ① using corns or screwdriver to open the bottom dam-board(picture 5), re...

  • Page 13

    12 pulley, motor and absorber 1 ①remove the back cover ②loosen the big screw nut from the pulley and take out the belt ③remove the pulley 2 ①take off the motor connection plug wire ②remove two bolts from motor holder, and take out the motor bush.(picture 14) ③follow the arrow to take off the motor (...

  • Page 14

    13 heater ⒉ loosen the m6 bolt from heater. Please do not compete loosen the bolt.(picture19) ②pull out the heater attention ensure the heater has put into the clip 19 switch component and door lock ①remove the front cover real ring spring (photo 7) ⒉ remove the 2 bolt from the fixed door lock (phot...

  • Page 15

    14 6.1.3 inside door as 6.1.4outside door as.

  • Page 16

    15 6.1.5 control panel as 6.1.6 drum as.

  • Page 17

    16 6.1.7 drying as （attention:this picture only for the washer combine with dryer machine）.

  • Page 18

    17 6.1.8 top cover as.

  • Page 19

    18 6.2 components exploded view.

  • Page 20

    19 10.2.1 、drum as.

  • Page 21

    20