Summary of ZN-DNT352XE SERIES
Page 2: Information To User
01a.01 2 information to user caution risk of electric shock, do not open ! Caution: to reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified seerivce personel. This symbol is intended to alert the user to the presence of un-i...
Page 3
01a.01 3 table of contents 1. Features ................................................................................................................. 4 2. Package contents ................................................................................................ 5 3. Part names ...............
Page 4
01a.01 4 1. Features camera full hd outdoor dome ip camera (vandal proof) high quality compression in real time streaming 1/2.7” high quality cmos image sensor true day / night (icr) and wdr improvement of color rolling suppression streaming dual streaming mode (such as different codec/resolution/bi...
Page 5
01a.01 5 2. Package contents unpack carefully and handle the equipment with care. The packaging contains: camera dc power adaptor dc jack cable 9-pin and 2-pin terminal block video out cable screws and anchors installation template hex wrench driver quick installation guide silicon waterproof band c...
Page 6
01a.01 6 3. Part names ① fan the fan and heater (underneath the black panel) are implemented for controlling temperature and mois ture of the internal device. ② reset button the reset button can be used for restarting the device or resetting it to factory default. Refer to 6.3. Re set and 6.4. Facto...
Page 7
01a.01 7 4. Installation note i when assembling the main body of the camera and its dome cover, make sure they fit each other into place. 1) place the installation template that is provided in the package on the desired position of installation. 2) attach the waterproof silicon band on the bottom pl...
Page 8
01a.01 8 caution ! The camera may fall off the ceiling even after the proper installation and mounting. To prevent any accident, make sure the ceiling is firm and stable enough to support the camera. If any reinforcement is needed, consult with your safety personnel and proceed with the installation...
Page 9
01a.01 9 4.2. Setting the lens position set the lens position and adjust the zoom and focus by performing procedures as below. 1) remove the dome cover. 2) adjust the lens to the desired position by manually moving its body in the following directions. 3) connect to the web page of the device to see...
Page 10
01a.01 10 5. Connections ① audio input/output the camera has a mono audio input and a mono audio output. Since the output power for the audio is low, an amplifier speaker is needed for a clearer sound (do not use a headphone or earphone directly to the camera). ② analog video output connection conne...
Page 11
01a.01 11 caution ! Do not exceed the maximum input voltage or relay rate. ④ alarm (do) connection only the relay type is supported. Relay rating: max 24vac 500ma or 12vdc 1a caution ! Do not exceed the maximum relay rating. Caution ! Must connect gnd port which is located between systems. Do com re...
Page 12
01a.01 12 ⑤ lan connection this is a rj45 lan connector for 10/100 base-t ethernet. Connect a lan cable. This led lights up as orange and turns green when the encoder is powered on. ⑥ 12v dc power a 12 dc power connector is required for this device. 12v red black led1 led2 zn-dnt352xe installation g...
Page 13
01a.01 13 6. Configuration 6.1.Set up network environment the default ip address of your ip device is 192.168.Xxx.Xxx. You can find the available ip address from the mac address of your device. Please make sure the device and your pc are on the same network segment before running the installation. I...
Page 14
01a.01 14 6.2.1. View video using ipadmin tool ipadmintool automatically searches all activated network encoders and ip cameras and shows the product name, ip address, mac address and etc. Ipadmintool is provided with sdk at the following sdk path. {sdk root}\bin\tools\admintool\ to use the ipadmint...
Page 15
01a.01 15 7. When the dialog box appears to request user name and password, enter the default value for the administrator account (case-sensitive) as below: id: root password: pass 8. Refresh the page and check if the live image is displayed successfully. 6.2.2.View video using ip address view the l...
Page 16
01a.01 16 appendix (a): specifications summary camera module cmos image sensor 1/2.7” 1080p cmos effective pixels 1920x1080 scanning system progressive scanning electrical resolution 1920 x 1080 min. Illumination color: 1.0 lux, f1.2 bw: 0.001 lux, f1.2 agc control auto lens 3.0~9.0mm vari-focal f1....
Page 17
01a.01 17 electrical characteristics power source dc 12v / poe ieee802.3af (class 0) power consumption 1100ma (heater on) video output 1 vp-p, 75Ω, composite audio input linein, 1.43vp-p(min 1.35vp-p, max 1.49 vp-p), 39 kΩ audio output lineout, 46mw power, 16 Ω d/i max 50ma@5vdc, ttl level 4.5v thre...
Page 18
01a.01 18 appendix (b): power over ethernet the power over ethernet (poe) is designed to extract power from a conventional twisted pair category 5 ethernet cable, conforming to the ieee 802.3af power-over-ethernet (poe) standard. Ieee 802.3af allows for two power options for category 5 cables. The p...
Page 19
01a.01 19 appendix (c): dimensions (unit: mm) zn-dnt352xe installation guide.
Page 20
01a.01 20 appendix (d): hexadecimal-decimal conversion table refer to the following table when you convert the mac address of your device to ip address. Hex dec 00 0 01 1 02 2 03 3 04 4 05 5 06 6 07 7 08 8 09 9 0a 10 0b 11 0c 12 0d 13 0e 14 0f 15 10 16 11 17 12 18 13 19 14 20 15 21 16 22 17 23 18 24...
Page 21
01a.01 21 revision history man# date(m/d/y) comments 01a.01 05/02/2012 first release version zn-dnt352xe installation guide.