1. DL manuals
  2. Garmin
  3. GPS
  4. GIA 63
  5. Installation Manual

Garmin GIA 63 Installation Manual

Other manuals for GIA 63: Installation Manual, Installation Manual

Summary of GIA 63

  • Page 1

    190-00303-05 december, 2012 revision y gia 63 installation manual.

  • Page 2

    190-00303-05 gia 63 installation manual rev. Y page a © copyright 2012 garmin ltd. Or its subsidiaries all rights reserved except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for any purpose wit...

  • Page 3

    190-00303-05 gia 63 installation manual rev. Y page i current revision description document pagination revision page number(s) section number description of change y 1-24 1.6.5 added cld part number 1-28 1.6.6 1-34 1.6.8 1-36 1.6.8 corrected tso-c169a class section page range table of contents i – v...

  • Page 4

    Gia 63 installation manual 190-00303-05 page ii rev. Y information subject to export control laws this document may contain information which is subject to the export administration regulations (“ear”) issued by the united states department of commerce (15 cfr, chapter vii subchapter c) and which ma...

  • Page 5

    190-00303-05 gia 63 installation manual rev. Y page iii limited warranty all garmin avionics products are warranted to be free from defects in materials or workmanship for: two years from the date of purchase for new remote-mount and panel-mount products; one year from the date of pu...

  • Page 6

    Gia 63 installation manual 190-00303-05 page iv rev. Y 1 general description ...........................................................................1-1 1.1 introduction ..................................................................................................................... 1-1 1.2 e...

  • Page 7

    190-00303-05 gia 63 installation manual rev. Y page v appendix a gia 63 main boot block uploading instructions .....A-1 a.1 introduction.................................................................................................................... A-1 a.2 determining current boot block............

  • Page 8

    Gia 63 installation manual 190-00303-05 page vi rev. Y gia 63 hardware mod level history the following table identifies hardware modification (mod) levels for the gia 63. Mod levels are listed with the associated service bulletin number, service bulletin date, and the purpose of the modif...

  • Page 9

    190-00303-05 gia 63 installation manual rev. Y page vii gia 63w/gia 63h hardware mod level history the following table identifies hardware modification (mod) levels for the gia 63w and gia 63h. Mod levels are listed with the associated service bulletin number, service bulletin date, and t...

  • Page 10

    Gia 63 installation manual 190-00303-05 page viii rev. Y this page intentionally left blank.

  • Page 11

    190-00303-05 gia 63 installation manual rev. Y page 1-1 1 general description 1.1 introduction this manual is intended to provide mechanical and electrical information for use in the planning and design of an installation of the gia 63(x) into an aircraft. This manual is not a substitute for an appr...

  • Page 12

    Gia 63 installation manual 190-00303-05 page 1-2 rev. Y 1.3 interface summary 1.3.1 primary interfaces the gia 63(x) is designed as an open architecture system that provides the following interfaces: • 1 dedicated ethernet high-speed data bus (hsdb) input/output channel • 2 controller area network (...

  • Page 13

    190-00303-05 gia 63 installation manual rev. Y page 1-3 1.4 technical specifications 1.4.1 environmental qualification form it is the responsibility of the installing agency to obtain the latest revision of the gia 63(x) environmental qualification form. This form is available directly from garmin u...

  • Page 14

    Gia 63 installation manual 190-00303-05 page 1-4 rev. Y 1.4.3 general specifications for detailed specifications, see the environmental qualification form. Table 1-2. Gia 63(x) general specifications characteristic specification operating temperature range -40°c to +65°c. For more details see enviro...

  • Page 15

    190-00303-05 gia 63 installation manual rev. Y page 1-5 1.4.4 gps specification (gia 63 only) 1.4.5 waas specific gps specifications (gia 63w & gia 63h) table 1-3. Gia 63 gps specifications characteristic specification acquisition times a) search-the-sky (without almanac, without initial position or...

  • Page 16

    Gia 63 installation manual 190-00303-05 page 1-6 rev. Y 1.4.6 com transceiver specifications table 1-5. Gia 63(x) com transceiver specifications characteristic specification audio output 100 mw minimum into a 500 Ω load audio response less than 6 db of variation between 350 and 2500 hz audio distort...

  • Page 17

    190-00303-05 gia 63 installation manual rev. Y page 1-7 1.4.7 vor specifications table 1-6. Gia 63(x) vor specifications characteristic specification receiver audio sensitivity at -103.5 dbm (s+n)/n shall not be less than 6 db course deviation sensitivity at –103.5 dbm deviation output shall not be ...

  • Page 18

    Gia 63 installation manual 190-00303-05 page 1-8 rev. Y 1.4.8 loc specifications table 1-7. Gia 63(x) loc specifications characteristic specification receiver audio sensitivity at -103.5 dbm (s+n)/n shall not be less than 6 db course deviation sensitivity at –103.5 dbm, deviation output shall not be...

  • Page 19

    190-00303-05 gia 63 installation manual rev. Y page 1-9 1.4.9 glideslope specifications 1.4.10 power requirements table 1-8. Gia 63(x) glideslope specifications characteristic specification sensitivity at –93 dbm, deviation output shall not be less than 60% of standard deflection when glideslope dev...

  • Page 20

    Gia 63 installation manual 190-00303-05 page 1-10 rev. Y 1.4.11 power interrupt superflag power requirements for p605 (main 2 connector) power depends upon loads present on superflag output pins (see sections 4.7.2.1 and 4.10.7) power requirements for p605 (main 2 connector) 1.0 a max @ 27.5 vdc (wi...

  • Page 21

    190-00303-05 gia 63 installation manual rev. Y page 1-11 1.5 license requirements the telecommunications act of 1996, effective february 8, 1996, provides the fcc discretion to eliminate radio station license requirements for aircraft and ships. The gia 63(x) installation must comply with current tr...

  • Page 22

    Gia 63 installation manual 190-00303-05 page 1-12 rev. Y 1.6 certification the gia 63 gps receiver is certified for ifr enroute, terminal, and non-precision approaches. The gia 63w and the gia 63h gps receivers are certified for lnav/vnav, lp, and lpv approaches. The gia 63(x) has been qualified to ...

  • Page 23

    190-00303-05 gia 63 installation manual rev. Y page 1-13 1.6.1 gia 63 tso/etso compliance table 1-11. Gia 63 tso/etso compliance function tso/etso category applicable lru sw part numbers applicable cld part numbers automatic pilots tso-c9c etso-c9c all 006-b0190-() except 006-b0190-00 through 006-b0...

  • Page 24

    Gia 63 installation manual 190-00303-05 page 1-14 rev. Y ground proximity warning – glide slope deviation alerting equipment tso-c92c all 006-b0190-() except 006-b0190-00 through 006-b0190-29 006-c0046-() 006-c0044-() 006-c0047-() 006-c0039-01 gps tso-c129a etso-c129a class a1 all 006-b0190-() excep...

  • Page 25

    190-00303-05 gia 63 installation manual rev. Y page 1-15 1.6.2 gia 63 tso/etso deviations table 1-12. Gia 63 tso/etso deviations tso/etso deviation tso-c9c 1. Garmin was granted a deviation from tso-c9c to use sae as 402b instead of as-402a. 2. Garmin was granted a deviation from tso-c9c to use do-1...

  • Page 26

    Gia 63 installation manual 190-00303-05 page 1-16 rev. Y tso-c92c 1. Garmin was granted a deviation from tso-c92c to use do-160d change 3 instead of do-160c. 2. Garmin was granted a deviation from tso-c92c to not include the version and levels of software or the modification status of hardware in th...

  • Page 27

    190-00303-05 gia 63 installation manual rev. Y page 1-17 1.6.3 gia 63w tso/etso compliance table 1-13. Gia 63w tso/etso compliance function tso/etso category applicable lru sw part numbers applicable cld part numbers automatic pilots tso-c9c etso-c9c all 006-b0544-1() through 006-b0544-4() and all 0...

  • Page 28

    Gia 63 installation manual 190-00303-05 page 1-18 rev. Y vor receiver tso-c40c etso-2c40c all 006-b0544-1() through 006-b0544-4() and all 006-b0544-b() except 006-b0544-ba through 006-b0544-bb all 006-b0082-0() except 006-b0082-00 through 006-b0082-02 all 006-c0084-0() except 006-c0084-00 006-c0072-...

  • Page 29

    190-00303-05 gia 63 installation manual rev. Y page 1-19 ground proximity warning – glide slope deviation alerting equipment tso-c92c etso-c92c all 006-b0544-3() through 006-b0544-4() and all 006-b0544-b() except 006-b0544-ba through 006-b0544-bb all 006-c0084-0() except 006-c0084-00 006-c0072-0() 0...

  • Page 30

    Gia 63 installation manual 190-00303-05 page 1-20 rev. Y vhf radio communications transceiver equipment tso-c169 equivalent to etso-2c37e & etso-2c38e class 3 and 5 (transmitter) class c and e (receiver) all 006-b0544-1() through 006-b0544-4() and all 006-b0544-b() except 006-b0544-ba through 006-b0...

  • Page 31

    190-00303-05 gia 63 installation manual rev. Y page 1-21 1.6.4 gia 63w tso/etso deviations table 1-14. Gia 63w tso/etso deviations tso/etso deviation tso-c9c 1. Garmin was granted a deviation from tso-c9c to use sae as 402b instead of as-402a. 2. Garmin was granted a deviation from tso-c9c to use do...

  • Page 32

    Gia 63 installation manual 190-00303-05 page 1-22 rev. Y tso-c92c 1. Garmin was granted a deviation from tso-c92c to use do-160e instead of do-160c. 2. Garmin was granted a deviation from tso-c92c to not include the version and levels of software or the modification status of hardware in the applian...

  • Page 33

    190-00303-05 gia 63 installation manual rev. Y page 1-23 tso-c169 1. Garmin was granted a deviation from tso-c169 to use do-160e instead of do-160d. 2. Garmin was granted a deviation to tso-c169, paragraph 4.D requirement to mark the installation procedures drawing number on the equipment. Garmin wi...

  • Page 34

    Gia 63 installation manual 190-00303-05 page 1-24 rev. Y 1.6.5 gia 63w updated nav/com tso/etso compliance table 1-15. Gia 63w updated nav/com tso/etso compliance function tso/etso category applicable lru sw part numbers applicable cld part numbers automatic pilots tso-c9c etso-c9c all 006-b0544-3()...

  • Page 35

    190-00303-05 gia 63 installation manual rev. Y page 1-25 vor receiver tso-c40c etso-2c40c all 006-b0544-3() through 006-b0544-4() except 006-b0544-30 through 006-b0544-34 and all 006-b0544-b() except 006-b0544-ba through 006-b0544-bd all 006-b0082-1() except 006-b0082-10 all 006-c0084-0() except 006...

  • Page 36

    Gia 63 installation manual 190-00303-05 page 1-26 rev. Y ground proximity warning – glide slope deviation alerting equipment tso-c92c etso-c92c all 006-b0544-3() through 006-b0544-4() except 006-b0544-30 through 006-b0544-34 and all 006-b0544-b() except 006-b0544-ba through 006-b0544-bd all 006-c008...

  • Page 37

    190-00303-05 gia 63 installation manual rev. Y page 1-27 airborne navigation sensors using the global positioning system augmented by the wide area augmentation system* tso-c145a etso-c145 class 3 all 006-b0544-3() through 006-b0544-4() except 006-b0544-30 through 006-b0544-34 and all 006-b0544-b() ...

  • Page 38

    Gia 63 installation manual 190-00303-05 page 1-28 rev. Y 1.6.6 gia 63h tso/etso compliance table 1-16. Gia 63h tso/etso compliance function tso/etso category applicable lru sw part numbers applicable cld part numbers automatic pilots tso-c9c etso-c9c all 006-b0544-3() through 006-b0544-4() except 00...

  • Page 39

    190-00303-05 gia 63 installation manual rev. Y page 1-29 vor receiver tso-c40c etso-2c40c all 006-b0544-3() through 006-b0544-4() except 006-b0544-30 through 006-b0544-35 and all 006-b0544-b() except 006-b0544-ba through 006-b0544-bd all 006-b0082-1() except 006-b0082-10 all 006-c0084-0() except 006...

  • Page 40

    Gia 63 installation manual 190-00303-05 page 1-30 rev. Y ground proximity warning – glide slope deviation alerting equipment tso-c92c etso-c92c all 006-b0544-3() through 006-b0544-4() except 006-b0544-30 through 006-b0544-35 and all 006-b0544-b() except 006-b0544-ba through 006-b0544-bd all 006-c008...

  • Page 41

    190-00303-05 gia 63 installation manual rev. Y page 1-31 vhf radio communications transceiver equipment tso-c169a equivalent to etso-2c37e & etso-2c38e class 3, 4, 5, and 6 (transmitter) class c and e (receiver) all 006-b0544-3() through 006-b0544-4() except 006-b0544-30 through 006-b0544-35 and all...

  • Page 42

    Gia 63 installation manual 190-00303-05 page 1-32 rev. Y 1.6.7 gia 63w updated nav/com and gia 63h tso/etso deviations table 1-17. Gia 63w updated nav/com and gia 63h tso/etso deviations tso/etso deviation tso-c9c 1. Garmin was granted a deviation from tso-c9c to use sae as 402b instead of as-402a. ...

  • Page 43

    190-00303-05 gia 63 installation manual rev. Y page 1-33 tso-c92c 1. Garmin was granted a deviation from tso-c92c to use do-160e instead of do-160c. 2. Garmin was granted a deviation from tso-c92c to not include the version and levels of software or the modification status of hardware in the applian...

  • Page 44

    Gia 63 installation manual 190-00303-05 page 1-34 rev. Y 1.6.8 gia 63w with enhanced com tso/etso compliance table 1-18. Gia 63w with enhanced com tso/etso compliance function tso/etso category applicable lru sw part numbers applicable cld part numbers automatic pilots tso-c9c all 006-b0544-4() and ...

  • Page 45

    190-00303-05 gia 63 installation manual rev. Y page 1-35 stall warning instruments tso-c54 type ii all 006-b0544-4() and all 006-b0544-b() except 006-b0544-ba through 006-b0544-bd all 006-c0084-0() except 006-c0084-00 006-c0072-0() 006-c0085-0() ground proximity warning – glide slope deviation alert...

  • Page 46

    Gia 63 installation manual 190-00303-05 page 1-36 rev. Y airborne navigation sensors using the global positioning system augmented by the wide area augmentation system* tso-c145c class 3 all 006-b0544-4() and all 006-b0544-b() except 006-b0544-ba through 006-b0544-bd 006-b0339-2() all 006-c0084-0() ...

  • Page 47

    190-00303-05 gia 63 installation manual rev. Y page 1-37 1.6.9 gia 63w with enhanced com tso/etso deviations table 1-19. Gia 63w with enhanced com tso/etso deviations tso/etso deviation tso-c9c 1. Garmin was granted a deviation from tso-c9c to use sae as 402b instead of as-402a. 2. Garmin was grante...

  • Page 48

    Gia 63 installation manual 190-00303-05 page 1-38 rev. Y tso-c160 1. Garmin was granted a deviation from rtca/do-224b paragraph 3.2.2.5.4.7 to meet attachment 2, table 2-1-3, item ho-argi of arinc 631-5, which states that neither the vdl ground station or air- craft will support aircraft requested g...

  • Page 49

    190-00303-05 gia 63 installation manual rev. Y page 1-39 tso-c169a 1. Garmin was granted a deviation from tso-c169a paragraph 4.A.2 to allow the unit to be perma- nently and legibly marked with a serial number and not the date of manufacture. 2. Garmin was granted a deviation from rtca/do-186b secti...

  • Page 50

    Gia 63 installation manual 190-00303-05 page 1-40 rev. Y 1.6.10 afm/rfm/afms/rfms/poh considerations per tso-c9c/etso-c9c deviation, the applicable afm/rfm/afms/rfms/poh shall list autopilot engagement envelope for the certified aircraft. Per tso-c52b/etso-c52b deviation, the applicable afm/rfm/afms...

  • Page 51

    190-00303-05 gia 63 installation manual rev. Y page 1-41 1.6.10.2 gia 63w and gia 63h gps software versions 3.2 or later the following information may be used as guidance in developing an approved afm, rfm, afms, rfms, and/or poh provided the system is installed in accordance with [ac 20-138c] and i...

  • Page 52

    Gia 63 installation manual 190-00303-05 page 1-42 rev. Y the garmin gnss navigation system complies with the accuracy, integrity, and continuity of function, and contains the minimum system functions required for p-rnav operations in accordance with jaa administrative & guidance material section one...

  • Page 53

    190-00303-05 gia 63 installation manual rev. Y page 1-43 garmin gnss (gps/sbas) navigation system limitations the flight crew must confirm at system initialization that the navigation database is current. Navigation database is expected to be current for the duration of the flight. If the airac cycl...

  • Page 54

    Gia 63 installation manual 190-00303-05 page 1-44 rev. Y both garmin gps navigation receivers must be operating and providing gps navigation guidance to their respective pfd for operations requiring rnp-4 performance. North atlantic (nat) minimum navigational performance specifications (mnps) airspa...

  • Page 55

    190-00303-05 gia 63 installation manual rev. Y page 1-45 1.6.11 other regulatory criteria (gia 63) rtca/do-178b level b, c, d (software) eurocae ed 12b (software) rtca/do-160d (environmental conditions) eurocae ed 14d (environmental conditions) rtca/do-161a (airborne ground proximity warning equipme...

  • Page 56

    Gia 63 installation manual 190-00303-05 page 1-46 rev. Y 1.6.12 other regulatory criteria (gia 63w and gia 63h) all 011-01105-xx part numbers: rtca/do-178b level a*, b, c, d (software) eurocae ed 12b (software) rtca/do-160e (environmental conditions) eurocae ed 14e (environmental conditions) rtca/do...

  • Page 57

    190-00303-05 gia 63 installation manual rev. Y page 1-47 1.7 reference documents the following publications are sources of additional information for installing the gia 63(x). Before installing the gia 63(x), the technician should read all relevant referenced materials along with this manual. Table ...

  • Page 58

    Gia 63 installation manual 190-00303-05 page 1-48 rev. Y this page intentionally left blank.

  • Page 59

    190-00303-05 gia 63 installation manual rev. Y page 2-1 2 installation overview 2.1 introduction this section provides hardware equipment information for installing the gia 63(x), related hardware, and antennas. Installation of the gia 63(x) should follow the aircraft tc or stc requirements. Cabling...

  • Page 60

    Gia 63 installation manual 190-00303-05 page 2-2 rev. Y 2.1.2 required accessories each of the following accessories is provided separately from the gia 63(x). Either rack (modular, standalone, or helicopter) and reminder of the accessories are required for installation. Table 2-2. Required accessor...

  • Page 61

    190-00303-05 gia 63 installation manual rev. Y page 2-3 2.1.3 additional equipment required the following installation accessories are required but not provided: com antenna: shall meet tso-c169()*, or shall meet both tso-c37() and c38(), broad band, 50 Ω , vertically polarized with coaxial cable gp...

  • Page 62

    Gia 63 installation manual 190-00303-05 page 2-4 rev. Y table 2-3. Tso-c145a waas antennas for the gia 63w and gia 63h model mount style conn type satcom compatible [3] mfr antenna part number garmin order number additional requirements ga 35 gps waas antenna [6] screw mount, teardrop footprint [2] ...

  • Page 63

    190-00303-05 gia 63 installation manual rev. Y page 2-5 the following is a list of known tso-c144 antennas that allow the gia 63w and gia 63h with any version of gps software version to meet tso-c145a requirements with the operational limitations specified in section 1.6.4 and 1.6.7 of this manual: ...

  • Page 64

    Gia 63 installation manual 190-00303-05 page 2-6 rev. Y 2.2 installation considerations the gia 63(x) interfaces with the g1000 system and with various avionics equipment. Fabrication of a wiring harness is required. Sound mechanical and electrical methods and practices are required for installation...

  • Page 65

    190-00303-05 gia 63 installation manual rev. Y page 2-7 for rotorcraft, locate the gps antenna as far as possible from the main rotor hub. This reduces the percentage of time the blade blocks the antenna. Also mount it as far below the blade surface as possible if installing the antenna under the bl...

  • Page 66

    Gia 63 installation manual 190-00303-05 page 2-8 rev. Y figure 2-1 shows the recommended placement of antennas. Figure 2-1. Gps antenna considerations.

  • Page 67

    190-00303-05 gia 63 installation manual rev. Y page 2-9 2.2.3 com antenna location the gia 63(x) com antenna should be well removed from all projections, engines and propellers. The ground plane surface directly below the antenna should be a flat plane over as large an area as possible (18 inches sq...

  • Page 68

    Gia 63 installation manual 190-00303-05 page 2-10 rev. Y if a com antenna is found to be the problem, a 1.57542 ghz notch filter (garmin p/n 330-00067-00) may be installed in the vhf com coax, as close to the com as possible. This filter is not required for the gia 63(x) transmitter. If a com is fou...

  • Page 69

    190-00303-05 gia 63 installation manual rev. Y page 2-11 2.4 cabling and wiring refer to the interconnect examples in appendix c for wire gauge guidance. In some cases, a larger gauge wire such as awg #16, #18, or #20 may be needed for power connections. Special thin-wall heat shrink tubing is also ...

  • Page 70

    Gia 63 installation manual 190-00303-05 page 2-12 rev. Y 2.6 gia 63 minimum installation requirements below is a list of required devices for tso-c129a category a1 certification. Pressure altitude device this device delivers pressure altitude data to the gia 63. This data comes from the garmin gdc 7...

  • Page 71

    190-00303-05 gia 63 installation manual rev. Y page 2-13 2. Electrical characteristics lna supply voltage 4.5 ± 0.5 vdc lna supply current 20 ma maximum lna operating frequency 1575.42 ± 2.00 mhz lna gain 20 db maximum, 12db minimum lna noise figure 3.0 db maximum lna output vswr (50 Ω ) 2:1 maximum...

  • Page 72

    Gia 63 installation manual 190-00303-05 page 2-14 rev. Y 2.8 mounting requirements the gia 63(x) mounting surface must be capable of providing structural support and electrical bond to the aircraft to minimize radiated emi and provide protection from high-intensity radiation fields (hirf). The gia 6...

  • Page 73

    190-00303-05 gia 63 installation manual rev. Y page 2-15 2.8.3 remote mounted stand-alone rack considerations figure 2-3 and figure b-4 show the gia 63(w) remote mounted stand-alone rack. The remote rack can be installed in a variety of locations, such as the electronics bay, under a seat, or on an ...

  • Page 74

    Gia 63 installation manual 190-00303-05 page 2-16 rev. Y figure 2-4. Gia 63h standalone rack.

  • Page 75

    190-00303-05 gia 63 installation manual rev. Y page 2-17 figure 2-5. Gia 63(w) standalone rack, suggested mounting locations.

  • Page 76

    Gia 63 installation manual 190-00303-05 page 2-18 rev. Y this page intentionally left blank.

  • Page 77

    190-00303-05 gia 63 installation manual rev. Y page 3-1 3 installation procedure 3.1 unpacking unit carefully unpack the equipment and make a visual inspection of the unit for evidence of damage incurred during shipment. If the unit is damaged, notify the carrier and file a claim. To justify a claim...

  • Page 78

    Gia 63 installation manual 190-00303-05 page 3-2 rev. Y 3.2 wiring harness installation allow adequate space for installation of cables and connectors. The installer shall supply and fabricate all of the cables. All electrical connections are made through 44, 62, and 78-pin d subminiature connectors...

  • Page 79

    190-00303-05 gia 63 installation manual rev. Y page 3-3 3.3 antenna installation for the com, vor/loc, and glideslope antenna, follow the manufacturers’ instructions. Avoid running other wires and coaxial cables near the vor/loc antenna cable. Caution do not use construction grade rtv sealant or sea...

  • Page 80

    Gia 63 installation manual 190-00303-05 page 3-4 rev. Y 3.5 backshell assembly the gia 63(x) connector kit includes six garmin backshell connectors. The backshell assemblies house the configuration module/temperature sensor, if applicable. Garmin’s backshell also gives the installer the ability to e...

  • Page 81

    190-00303-05 gia 63 installation manual rev. Y page 3-5 installation instructions for the gia 63(h) for installation and assembly, refer to the outline and installation drawings shown in appendix b of this manual. 1. Assemble the backshell connectors, refer to section 3.5. 2. Connect backshell conne...

  • Page 82

    Gia 63 installation manual 190-00303-05 page 3-6 rev. Y 3.8 continued airworthiness maintenance of the gia 63(x) is “on condition” for all units installed in airframes that require power interrupt category b (50ms). For airframes that require the gia 63(x) to comply with rtca/do-160d or rtca/do-160e...

  • Page 83

    190-00303-05 gia 63 installation manual rev. Y page 3-7 3.8.1 category a long term power interrupt annual inspection note in order to comply with this procedure gia 63 main software version must be 5.30 or later, gia 63w main software version must be 5.21 or later, and gdu main software version must...

  • Page 84

    Gia 63 installation manual 190-00303-05 page 3-8 rev. Y this page intentionally left blank.

  • Page 85

    190-00303-05 gia 63 installation manual rev. Y page 4-1 4 system interconnects 4.1 pin function list 4.1.1 p601 (com) figure 4-1. View of j601 connector from back of unit table 4-1. P601 (com) pin list pin pin name i/o 1 reserved (unsquelched audio test) -- com unsquelched audio output (011-01105-4x...

  • Page 86

    Gia 63 installation manual 190-00303-05 page 4-2 rev. Y *indicates active low (ground to activate) † pin not currently supported 22 spare -- 23 aircraft power 2 in 24 spare -- 25 aircraft power 2 in 26 spare -- 27 aircraft power 2 in 28 reserved -- 29 reserved -- 30 power ground -- 31 power ground -...

  • Page 87

    190-00303-05 gia 63 installation manual rev. Y page 4-3 4.1.2 p602 (vor/ils) figure 4-2. View of j602 connector from back of unit table 4-2. P602 (vor/ils) pin list pin pin name i/o 1 vor/loc +to out 2 vor/loc +from (vor/loc common) out vor/loc +from (nav common) (011-01105-2x/-3x/-4x only) out 3 vo...

  • Page 88

    Gia 63 installation manual 190-00303-05 page 4-4 rev. Y 22 signal ground -- 23 vor/ils arinc 429 out b out 24 vor/ils arinc 429 out a out 25 vor obi clock out 26 vor obi sync out 27 vor obi data out 28 vor/ils remote transfer* in 29 ils energize* out 30 reserved -- 31 reserved -- 32 glideslope +flag...

  • Page 89

    190-00303-05 gia 63 installation manual rev. Y page 4-5 *indicates active low (ground to activate) † pin not currently supported 53 glideslope –flag (glideslope common) out glideslope –flag (nav common) (011-01105-2x/-3x/-4x only) out 54 parallel dme 100khz-e out 55 glideslope +down (glideslope comm...

  • Page 90

    Gia 63 installation manual 190-00303-05 page 4-6 rev. Y 4.1.3 p603 (main serial) figure 4-3. View of j603 connector from back of unit table 4-3. P603 main serial pin pin name i/o 1 reserved -- 2 ethernet out a out 3 ethernet out b out 4 rs-485 4 a i/o 5 rs-485 4 a i/o 6 rs-485 4 b i/o 7 rs-485 4 b i...

  • Page 91

    190-00303-05 gia 63 installation manual rev. Y page 4-7 26 rs-485 2 b i/o 27 rs-485 3 a/rs-422 in a i/o 28 rs-485 3 b/rs-422 in b i/o 29 main arinc 429 in 1 a in 30 can bus 2 lo i/o 31 main arinc 429 in 1 b in 32 can bus 2 h i/o 33 main arinc 429 in 2 a in 34 can bus 1 termination -- 35 main arinc 4...

  • Page 92

    Gia 63 installation manual 190-00303-05 page 4-8 rev. Y *indicates active low (ground to activate) † pin not currently supported 58 main rs-232 out 6 out 59 main rs-232 in 7 in 60 reserved -- 61 signal ground -- 62 main rs-232 out 7 out 63 main rs-232 in 8 in 64 signal ground -- 65 main rs-232 out 8...

  • Page 93

    190-00303-05 gia 63 installation manual rev. Y page 4-9 4.1.4 p604 (main discrete) figure 4-4. View of j604 connector from back of unit table 4-4. P604 (main discrete) pin list pin pin name i/o 1 annunciate* 22 out 2 voice alert 500 Ω audio out hi out 3 voice alert 500 Ω audio out lo out 4 discrete ...

  • Page 94

    Gia 63 installation manual 190-00303-05 page 4-10 rev. Y *indicates active low (ground to activate) † pin not currently supported 26 annunciate* 3 out 27 annunciate* 4 out 28 annunciate* 5 out 29 annunciate* 6 out 30 annunciate* 7 out 31 annunciate* 8 out 32 annunciate* 9 out 33 annunciate* 10 out 3...

  • Page 95

    190-00303-05 gia 63 installation manual rev. Y page 4-11 4.1.5 p605 (i/o 1) figure 4-5. View of j605 connector from back of unit table 4-5. P605 (i/o 1) pin list pin pin name i/o 1 radar altimeter dc hi† in 2 radar altimeter dc lo† in 3 discrete in 18a in 4 spare -- 5 spare -- 6 spare -- 7 spare -- ...

  • Page 96

    Gia 63 installation manual 190-00303-05 page 4-12 rev. Y 26 main vertical –flag (main common) out 27 spare -- 28 spare -- 29 aircraft power 1 in 30 potentiometer signal out† out 31 aircraft power 1 in 32 potentiometer ref out hi out 33 aircraft power 2 in 34 potentiometer ref out lo (ground) out 35 ...

  • Page 97

    190-00303-05 gia 63 installation manual rev. Y page 4-13 *indicates active low (ground to activate) † pin not currently supported 58 airway/inner marker lamp in in 59 discrete in* 16a in 60 discrete in 23a in 61 signal ground -- 62 main lateral superflag out 63 main vertical superflag out 64 superfl...

  • Page 98

    Gia 63 installation manual 190-00303-05 page 4-14 rev. Y 4.1.6 p606 (i/o 2) figure 4-6. View of j606 connector from back of unit table 4-6. P606 (i/o 2) pin list pin pin name i/o 1 26 vac vertical gyro ref hi† in 2 26 vac vertical gyro ref lo† in 3 26 vac adf ref hi† in 4 26 vac adf ref lo† in 5 26 ...

  • Page 99

    190-00303-05 gia 63 installation manual rev. Y page 4-15 26 spare -- 27 spare -- 28 spare -- 29 reserved -- 30 signal ground -- 31 reserved -- 32 adf dc ref in in 33 reserved -- 34 analog roll steering h out 35 reserved -- 36 analog roll steering lo (ground) out 37 heading bootstrap out x† out 38 he...

  • Page 100

    Gia 63 installation manual 190-00303-05 page 4-16 rev. Y *indicates active low (ground to activate) † pin not currently supported 58 main obi sync† out 59 main king serial dme data i/o 60 main king serial dme clock i/o 61 reserved out 62 main king serial dme request out 63 main king serial dme on* o...

  • Page 101

    190-00303-05 gia 63 installation manual rev. Y page 4-17 4.2 power and antennas 4.2.1 power functions this section covers the power input requirements. 4.2.1.1 aircraft power pins 17, 19, and 21 of p601 are internally connected to form aircraft power 1. Pins 23, 25, and 27 of p601 are internally con...

  • Page 102

    Gia 63 installation manual 190-00303-05 page 4-18 rev. Y 4.2.1.2 remote on/off inactive: vin ≤ 3.5vdc active: 10 ≤ vin ≤ 33vdc with ≥ 75 ua source current source current is internally limited to 1.5 ma max for a 10-33vdc input 4.2.1.3 antennas table 4-8. Remote on/off pin name connector pin i/o gia ...

  • Page 103

    190-00303-05 gia 63 installation manual rev. Y page 4-19 4.3 gia system id program the gia 63(x) utilizes a hard strapping method to assign a unit id to a unit. Unit id’s identify a unit as a #1, #2, #3, or #4 gia. 4.4 serial data 4.4.1 serial data electrical characteristics 4.4.1.1 rs-232 the rs-23...

  • Page 104

    Gia 63 installation manual 190-00303-05 page 4-20 rev. Y 4.4.1.2 rs-485/422 the gia 63(x) contains a total of 5 channels of rs-485 serial data communications. Any two of these channels can also be configured as one rs-422 channel to allow for system flexibility. These data busses conform to eia stan...

  • Page 105

    190-00303-05 gia 63 installation manual rev. Y page 4-21 4.4.1.3 arinc 429 the main and vor/ils arinc 429 outputs conform to arinc 429 electrical specifications when loaded with up to 5 standard arinc 429 receivers. Table 4-13. Arinc 429 pin name connector pin i/o main arinc 429 in 1 a p603 29 in ma...

  • Page 106

    Gia 63 installation manual 190-00303-05 page 4-22 rev. Y 4.4.1.4 can bus this data bus conforms to the bosch standard for controller area network 2.0-b. This bus complies with iso 11898. Can bus termination should be connected to can bus lo if gia is located at the end of the bus. 4.4.1.5 ethernet h...

  • Page 107

    190-00303-05 gia 63 installation manual rev. Y page 4-23 4.5 discrete i/o discrete in* pins: inactive: 10 ≤ vin ≤ 33vdc or rin ≥ 100k Ω active: vin ≤ 1.9vdc with ≥ 75 ua sink current, or rin ≤ 375 Ω sink current is internally limited to 200 ua max for a grounded input discrete in pins: inactive: vin...

  • Page 108

    Gia 63 installation manual 190-00303-05 page 4-24 rev. Y 4.6 com/vor/ils/digital audio 4.6.1 com/vor/ils/digital audio function and emergency mode activation of com mic key* enables com mic audio and causes the transceiver to transmit. 500 Ω com audio and 500 Ω vor/ils audio are 100 mw audio outputs...

  • Page 109

    190-00303-05 gia 63 installation manual rev. Y page 4-25 4.6.2 com/vor/ils/digital audio electrical characteristics 4.6.2.1 com mic key inactive: 10 ≤ vin ≤ 33vdc or rin ≥ 100k Ω active: vin ≤ 1.9vdc with ≥ 75 ua sink current, or rin ≤ 375 Ω sink current is internally limited to 200 ua max for a gro...

  • Page 110

    Gia 63 installation manual 190-00303-05 page 4-26 rev. Y 4.6.2.4 digital audio when interfaced to a compatible garmin gma series audio panel, these can be used in place of analog audio lines. In dual gma installations the cross-side com mic digital audio in allows a working gma to access digital aud...

  • Page 111

    190-00303-05 gia 63 installation manual rev. Y page 4-27 4.6.2.5 discrete inputs inactive: 10 ≤ vin ≤ 33vdc or rin ≥ 100k Ω active: vin ≤ 1.9vdc with ≥ 75 ua sink current, or rin ≤ 375 Ω sink current is internally limited to 200 ua max for a grounded input the com remote transfer* input behavior is ...

  • Page 112

    Gia 63 installation manual 190-00303-05 page 4-28 rev. Y 4.7 vor/ils indicator 4.7.1 vor/ils indicator function the vor/ils indicator displays both lateral and vertical, to/from indications, lateral flags, vertical flags, and superflags. Vor/loc composite out is a standard vor/localizer composite si...

  • Page 113

    190-00303-05 gia 63 installation manual rev. Y page 4-29 4.7.2.3 to/from the output is capable of driving up to three 200 Ω meter loads. When indicating to, the output is +225 ±75 mvdc. When indicating from, output is -225 ±75 mvdc. When invalid information is present (flag in view) the to/from outp...

  • Page 114

    Gia 63 installation manual 190-00303-05 page 4-30 rev. Y 4.7.2.5 obs vor obs rotor c and h are a buffered 500 hz output that is intended to drive the obs rotors. Vor obs stator d and vor obs stator f are each phase and amplitude shifted version of the vor rotor c output. Each pair is intended to rea...

  • Page 115

    190-00303-05 gia 63 installation manual rev. Y page 4-31 4.7.2.8 ils energize inactive: floating (can be pulled up to externally sourced vout in the range 0 ≤ vout ≤ 33vdc) leakage current in the inactive state is typically ≤ 10 ua to ground active: vout ≤ 0.5vdc with ≤ 20 ma sink current sink curre...

  • Page 116

    Gia 63 installation manual 190-00303-05 page 4-32 rev. Y 4.8 rmi/obi 4.8.1 rmi/obi function the vor obi output provides bearing information from the active waypoint based upon the vor receiver. When a localizer channel is tuned on the vloc window, there is a bit in the data stream set to indicate th...

  • Page 117

    190-00303-05 gia 63 installation manual rev. Y page 4-33 4.9 dme tuning and adf 4.9.1 dme tuning function the gia 63(x) can channel a dme based on the tuned vloc frequency. The gia 63(x) outputs 2 of 5, bcd or slip parallel dme and king serial dme channeling format. When dme common is held low, the ...

  • Page 118

    Gia 63 installation manual 190-00303-05 page 4-34 rev. Y 4.9.2.2 king serial dme interface these pins are used when the gia 63(x) is configured for king serial dme tuning. Input logic levels are: high 6.5 vdc or greater low 3.5 vdc or less 4.9.2.3 automatic direction finder inputs table 4-33. King s...

  • Page 119

    190-00303-05 gia 63 installation manual rev. Y page 4-35 4.10 auto pilot 4.10.1 flight instruments inputs from afcs that direct the pilot through the pfd. The input voltage is positive if flight director pitch +up is greater than flight director pitch +down. Otherwise the input voltage is negative. ...

  • Page 120

    Gia 63 installation manual 190-00303-05 page 4-36 rev. Y 4.10.2 automatic flight control system outputs variable-amplitude output, which is proportional to the aircraft roll command from the gps navigation system. Outputs heading datum information to afcs. Table 4-36. Analog roll steering pin name c...

  • Page 121

    190-00303-05 gia 63 installation manual rev. Y page 4-37 outputs course datum information to afcs. Table 4-38. Course datum pin name connector pin i/o course datum hi p606 48 out course datum lo (ground) p606 49 -- dc amplitude: -15 to +15 vdc load impedance: > 5 k Ω scaling: 0.21 vdc per degree of ...

  • Page 122

    Gia 63 installation manual 190-00303-05 page 4-38 rev. Y 4.10.3 main deviation outputs the deviation output is capable of driving up to three 1000 Ω loads with ±150 mv dc ±5% for full-scale deflection. The drive circuit provides for more than full-scale deflection with a maximum course deviation out...

  • Page 123

    190-00303-05 gia 63 installation manual rev. Y page 4-39 4.10.4 remote annunciate data bus these inputs read the remote annunciate data bus that the autopilot uses to tell its remote annunciator panel what mode it is operating in. The gia 63 requires 4.7 k Ω pull-up resistors to +28 v dc in the airc...

  • Page 124

    Gia 63 installation manual 190-00303-05 page 4-40 rev. Y this page intentionally left blank.

  • Page 125

    190-00303-05 gia 63 installation manual rev. Y page a-1 appendix a gia 63 main boot block uploading instructions note this appendix applies to the gia 63 only, and does not apply to the gia 63w or gia 63h. A.1 introduction this appendix contains instructions on how to upgrade main boot block softwar...

  • Page 126

    Gia 63 installation manual 190-00303-05 page a-2 rev. Y 9. On the pfd use the fms knob to turn to the software upload page. 10. Use the fms knob to highlight gia 6x software. Figure a-2. Gia 6x software 11. Press the lru softkey and highlight ‘gia 1’. 12. Press the ent key to begin loading software....

  • Page 127

    190-00303-05 gia 63 installation manual rev. Y page a-3 caution do not turn power off or cancel the software upload while the boot block is loading. 11. Confirm update completion and press the ent key. 12. On the mfd use the fms knob to turn to the system status page. 13. Highlight ‘gia 1’. 14. Veri...

  • Page 128

    Gia 63 installation manual 190-00303-05 page a-4 rev. Y this page intentionally left blank.

  • Page 129

    190-00303-05 gia 63 installation manual rev. Y page b-1 appendix b outline and installation drawings figure b-1. Gia 63(w) modular installation outline drawing.

  • Page 130

    190-00303-05 gia 63 installation manual rev. Y page b-2 appendix b outline and installation drawings figure b-2. Gia 63(w) modular installation drawing.

  • Page 131

    190-00303-05 gia 63 installation manual rev. Y page b-3 appendix b outline and installation drawings figure b-3. Gia 63(w) standalone installation outline drawing.

  • Page 132

    190-00303-05 gia 63 installation manual rev. Y page b-4 appendix b outline and installation drawings figure b-4. Gia 63(w) standalone installation drawing.

  • Page 133

    190-00303-05 gia 63 installation manual rev. Y page b-5 appendix b outline and installation drawings figure b-5. Gia 63h standalone installation outline drawing.

  • Page 134

    190-00303-05 gia 63 installation manual rev. Y page b-6 appendix b outline and installation drawings figure b-6. Gia 63h standalone installation drawing.

  • Page 135

    190-00303-05 gia 63 installation manual rev. Y page c-1 appendix c interconnect drawings figure c-1. Gia 63(x) example interconnect.

  • Page 136

    190-00303-05 gia 63 installation manual rev. Y page c-2 appendix c interconnect drawings figure c-2. Gia 63(x) example interconnect.

  • Page 137

    190-00303-05 gia 63 installation manual rev. Y page c-3 appendix c interconnect drawings figure c-3. Gia 63(x) example interconnect.

  • Page 138

    190-00303-05 gia 63 installation manual rev. Y page c-4 appendix c interconnect drawings figure c-4. Gia 63(x) example interconnect.

  • Page 139

    190-00303-05 gia 63 installation manual rev. Y page c-5 appendix c interconnect drawings figure c-5. Gia 63(x) example interconnect.

  • Page 140

    190-00303-05 gia 63 installation manual rev. Y page c-6 appendix c interconnect drawings figure c-6. Gia 63(x) example interconnect.

  • Page 141

    190-00303-05 gia 63 installation manual rev. Y page c-7 appendix c interconnect drawings figure c-7. Gia 63(x) example interconnect.