- DL manuals
- Garmin
- GPS
- GIA 63
- Installation Manual
Garmin GIA 63 Installation Manual
Summary of GIA 63
Page 1
190-00303-05 november, 2010 revision t gia 63 installation manual draft rev t 11/12/2010
Page 2
Page a gia 63 installation manual revision t 190-00303-05 © copyright 2010 garmin ltd. Or its subsidiaries all rights reserved except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for any purpose...
Page 3
Gia 63 installation manual page i 190-00303-05 revision t current revision description revision page number(s) section number description of change ii toc added reference to gia 63h and note regarding gia 63(x) v, vi toc updated mod level tables 1-1–1-32 1 updated to gia 63(x) where applicable, adde...
Page 4
Page ii gia 63 installation manual revision t 190-00303-05 this manual reflects the operation of main software version 5.31 for the gia 63 and main software version 6.00 for the gia 63w and gia 63h. Some differences in operation may be observed when comparing the information in this manual to earlie...
Page 5
Gia 63 installation manual page iii 190-00303-05 revision t table of contents paragraph page 1 general description..............................................................................................................1-1 1.1 introduction...........................................................
Page 6
Page iv gia 63 installation manual revision t 190-00303-05 paragraph page appendix a gia 63 main boot block uploading instructions................................. A-1 a.1 introduction.......................................................................................................................
Page 7
Gia 63 installation manual page v 190-00303-05 revision t gia 63 hardware mod level history the following table identifies hardware modification (mod) levels for the gia 63. Mod levels are listed with the associated service bulletin number, service bulletin date, and the purpose of the modification....
Page 8
Page vi gia 63 installation manual revision t 190-00303-05 gia 63w/gia 63h hardware mod level history the following table identifies hardware modification (mod) levels for the gia 63w and gia 63h. Mod levels are listed with the associated service bulletin number, service bulletin date, and the purpo...
Page 9
Gia 63 installation manual page 1-1 190-00303-05 revision t 1 general description 1.1 introduction this manual presents mechanical and electrical installation requirements for installing the gia 63(x) as part of a garmin integrated flight deck. The gia 63(x) can be integrated into a variety of airfr...
Page 10
Page 1-2 gia 63 installation manual revision t 190-00303-05 1.3 interface summary 1.3.1 primary interfaces the gia 63(x) is designed as an open architecture system that provides the following interfaces: • 1 dedicated ethernet high-speed data bus (hsdb) input/output channel • 2 controller area netwo...
Page 11
Gia 63 installation manual page 1-3 190-00303-05 revision t 1.4 technical specifications 1.4.1 environmental qualification form it is the responsibility of the installing agency to obtain the latest revision of the gia 63(x) environmental qualification form. These forms are available directly from g...
Page 12
Page 1-4 gia 63 installation manual revision t 190-00303-05 1.4.4 gps specifications (gia 63 only) characteristics specifications acquisition time a) search-the-sky (without almanac, without initial position or time): 5 minutes b) autolocate™ (with almanac, without initial position or time): 5 minut...
Page 13
Gia 63 installation manual page 1-5 190-00303-05 revision t 1.4.6 com transceiver specifications characteristics specifications audio output 100 mw minimum into a 500 Ω load. Audio response less than 6 db of variation between 350 and 2500 hz. Audio distortion the distortion in the receiver audio out...
Page 14
Page 1-6 gia 63 installation manual revision t 190-00303-05 1.4.7 vor specifications characteristics specifications receiver audio sensitivity at -103.5 dbm (s+n)/n shall not be less than 6 db. Course deviation sensitivity at –103.5 dbm deviation output shall not be less than 60% of standard deflect...
Page 15
Gia 63 installation manual page 1-7 190-00303-05 revision t 1.4.8 loc specifications characteristics specifications receiver audio sensitivity at -103.5 dbm (s+n)/n shall not be less than 6 db. Course deviation sensitivity at –103.5 dbm, deviation output shall not be less than 60% of standard deflec...
Page 16
Page 1-8 gia 63 installation manual revision t 190-00303-05 1.4.9 glideslope specifications characteristics specifications sensitivity at –93 dbm, deviation output shall not be less than 60% of standard deflection when glideslope deviation test signal is applied. Centering accuracy 0 ± .0091 ddm or ...
Page 17
Gia 63 installation manual page 1-9 190-00303-05 revision t 1.4.11 power interrupt unit name unit part number mod status* long term power interrupt category per rtca do-160d** 4 a (200ms) 011-00781-00 0, 1, 2, 3 b (50ms) 1 a (200ms) gia 63 011-00781-01 0 b (50ms) 1 a (200ms) 011-01105-00 0 b (50ms) ...
Page 18
Page 1-10 gia 63 installation manual revision t 190-00303-05 1.6 certification the gia 63 gps receiver is certified for ifr enroute, terminal, and non-precision approaches. The gia 63w and the gia 63h gps receivers are waas certified. The gia 63(x) has been qualified to rtca/do-160 section 20 rf sus...
Page 19
Gia 63 installation manual page 1-11 190-00303-05 revision t 1.6.1 gia 63 tso/etso compliance function tso/etso category applicable lru sw part numbers applicable cld part numbers 006-c0046-() 006-c0044-() 006-c0047-() automatic pilots tso-c9c etso-c9c all 006-b0190-() except 006-b0190-00 through 00...
Page 20
Page 1-12 gia 63 installation manual revision t 190-00303-05 1.6.2 gia 63 tso/etso deviations tso/etso deviation 1. Garmin was granted a deviation from tso-c9c to use sae as 402b instead of as- 402a. 2. Garmin was granted a deviation from tso-c9c to use do-160d instead of specified environmental tes...
Page 21
Gia 63 installation manual page 1-13 190-00303-05 revision t gia 63 tso/etso deviations, continued tso/etso deviation 1. Garmin was granted a deviation from tso-c92c to use do-160d change 3 instead of do-160c. Tso-c92c 2. Garmin was granted a deviation from tso-c92c to not include the version and le...
Page 22
Page 1-14 gia 63 installation manual revision t 190-00303-05 1.6.3 gia 63w tso/etso compliance function tso/etso category applicable lru sw part numbers applicable cld part numbers all 006-c0084-0() except 006-c0084-00 006-c0072-0() 006-c0085-0() automatic pilots tso-c9c etso-c9c all 006-b0544-1) th...
Page 23
Gia 63 installation manual page 1-15 190-00303-05 revision t gia 63w tso/etso compliance, continued function tso/etso category applicable lru sw part numbers applicable cld part numbers all 006-c0084-0() except 006-c0084-00 006-c0072-0() 006-c0085-0() all 006-c0039-0() except 006-c0039-00 through 00...
Page 24
Page 1-16 gia 63 installation manual revision t 190-00303-05 gia 63w tso/etso compliance, continued function tso/etso category applicable lru sw part numbers applicable cld part numbers all 006-c0084-0() except 006-c0084-00 tso-c151b class a and b 006-c0072-0() 006-c0085-0() taws etso-c151a class b ...
Page 25
Gia 63 installation manual page 1-17 190-00303-05 revision t 1.6.4 gia 63w tso/etso deviations tso/etso deviation 1. Garmin was granted a deviation from tso-c9c to use sae as 402b instead of as- 402a. 2. Garmin was granted a deviation from tso-c9c to use do-160e instead of specified environmental te...
Page 26
Page 1-18 gia 63 installation manual revision t 190-00303-05 gia 63w tso/etso deviations, continued tso/etso deviation 1. Garmin was granted a deviation from tso-c145a to use do-160e instead of do-160d. 2. Garmin was granted a deviation from rtca/do-229c paragraphs 2.1.1.10, 2.1.1.7, 2.1.1.8.1, 2.1....
Page 27
Gia 63 installation manual page 1-19 190-00303-05 revision t gia 63w tso/etso deviations, continued tso/etso deviation 1. Garmin was granted a deviation from tso-c169 to use do-160e instead of do-160d. 2. Garmin was granted a deviation to tso-c169, paragraph 4.D requirement to mark the installation ...
Page 28
Page 1-20 gia 63 installation manual revision t 190-00303-05 1.6.5 gia 63w updated nav/com and gia 63h tso/etso compliance function tso/etso category applicable lru sw part numbers applicable cld part numbers all 006-c0084-0() except 006-c0084-00 006-c0072-0() automatic pilots tso-c9c all 006-b0544-...
Page 29
Gia 63 installation manual page 1-21 190-00303-05 revision t gia 63w updated nav/com and gia 63h tso/etso compliance, continued function tso/etso category applicable lru sw part numbers applicable cld part numbers all 006-c0084-0() except 006-c0084-00 006-c0072-0() ground proximity warning – glide s...
Page 30
Page 1-22 gia 63 installation manual revision t 190-00303-05 1.6.6 gia 63w updated nav/com and gia 63h tso/etso deviations tso/etso deviation 1. Garmin was granted a deviation from tso-c9c to use sae as 402b instead of as- 402a. 2. Garmin was granted a deviation from tso-c9c to use do-160e instead o...
Page 31
Gia 63 installation manual page 1-23 190-00303-05 revision t 1.6.7 afm/afms/poh considerations per tso-c9c deviation, the applicable afm, afms, and/or poh shall list autopilot engagement envelope for the certified aircraft. Per tso-c52b deviation, the applicable afm, afms, and/or poh shall state tha...
Page 32
Page 1-24 gia 63 installation manual revision t 190-00303-05 the following information may be published in the approved afm, afms, and/or poh provided the system is installed in accordance with ac 20-138a and is comprised of two tso-c145a class 3 approved garmin gia 63w or gia 63h units, two/three t...
Page 33
Gia 63 installation manual page 1-25 190-00303-05 revision t the gnss navigation system has [two etso-145 / tso-c145a class 3 approved garmin gia 63w and gia 63h units, and etso-146 / tso-c146a class 3 approved garmin gdu 1xxx display units]. The garmin gnss navigation system as installed in this ai...
Page 34
Page 1-26 gia 63 installation manual revision t 190-00303-05 confirmed for the intended flight (route and time). In the event of a predicted continuous loss of raim of more than five minutes for any part of the intended flight, the flight should be delayed, canceled, or re- routed on a track where r...
Page 35
Gia 63 installation manual page 1-27 190-00303-05 revision t navigation information is referenced to wgs-84 reference system, and should only be used where the aeronautical information publication (including electronic data and aeronautical charts) conform to wgs-84 or equivalent. 1.6.8 other regula...
Page 36
Page 1-28 gia 63 installation manual revision t 190-00303-05 1.7 referenced documents the following publications are sources of additional information for installing the gia 63(x). Before installing the gia 63(x), the technician should read all referenced materials along with this manual. Part numbe...
Page 37
Gia 63 installation manual page 1-29 190-00303-05 revision t 1.8 limited warranty all garmin avionics products are warranted to be free from defects in materials or workmanship for: two years from the date of purchase for new remote-mount and panel-mount products; one year from the date of purchase ...
Page 38
Page 1-30 gia 63 installation manual revision t 190-00303-05 this page intentionally left blank draft rev t 11/12/2010
Page 39
Gia 63 installation manual page 2-1 190-00303-05 revision t 2 installation overview 2.1 introduction this section provides hardware equipment information for installing the gia 63(x), related hardware, and antennas. Installation of the gia 63(x) should follow the aircraft tc or stc requirements. Cab...
Page 40
Page 2-2 gia 63 installation manual revision t 190-00303-05 2.1.2 required accessories each of the following accessories is provided separately from the gia 63(x). Either rack (modular, standalone, or helicopter) and remainder of the accessories are required for installation. Item garmin p/n gia 63(...
Page 41
Gia 63 installation manual page 2-3 190-00303-05 revision t 2.1.3.1 required antennas for the gia 63 antennas used with the gia 63 (non-waas) must meet the antenna specifications shown in section 2.6. In addition, tso-c144 antennas can also meet tso-c129a requirements for the gia 63 (non-waas) if th...
Page 42
Page 2-4 gia 63 installation manual revision t 190-00303-05 the following is a list of known tso-c144 antennas that allow the gia 63w and gia 63h with any version of gps software version to meet tso-c145a requirements with the operational limitations specified in section 1.6.5 of this manual: model ...
Page 43
Gia 63 installation manual page 2-5 190-00303-05 revision t 2.2 installation considerations the gia 63(x) interfaces with the g1000 system and with various avionics equipment. Fabrication of a wiring harness is required. Sound mechanical and electrical methods and practices are required for installa...
Page 44
Page 2-6 gia 63 installation manual revision t 190-00303-05 2.2.2 gps antenna location the gps antenna is a key element in the overall system performance and integrity for a gps/waas navigation system. The mounting location, geometry, and surroundings of the antenna can affect the system performance...
Page 45
Gia 63 installation manual page 2-7 190-00303-05 revision t figure 2-1 shows the recommended placement of antennas. Figure 2-1. Gps antenna considerations draft rev t 11/12/2010
Page 46
Page 2-8 gia 63 installation manual revision t 190-00303-05 2.2.3 com antenna location the gia 63(x) com antenna should be well removed from all projections, engines and propellers. The ground plane surface directly below the antenna should be a flat plane over as large an area as possible (18 inche...
Page 47
Gia 63 installation manual page 2-9 190-00303-05 revision t 2.2.7 vhf com/gps interference on some installation vhf com transceivers, emergency locator transmitter (elt) antennas, and direction finder (df) receiver antennas can re-radiate through the gps antenna. The gia 63(x) com does not interfere...
Page 48
Page 2-10 gia 63 installation manual revision t 190-00303-05 2.4 cabling and wiring refer to the interconnect examples in appendix c for wire gauge guidance. In some cases, a larger gauge wire such as awg #16, #18, or #20 may be needed for power connections. Special thin-wall heat shrink tubing is a...
Page 49
Gia 63 installation manual page 2-11 190-00303-05 revision t 2.6 gia 63 minimum installation requirements below is a list of required devices for tso-c129a category a1 certification. Pressure altitude device this device delivers pressure altitude data to the gia 63. This data comes from the garmin g...
Page 50
Page 2-12 gia 63 installation manual revision t 190-00303-05 3. Radiation characteristics polarization rhcp operating frequency 1575.42 ± 2.00 mhz gain (on axis) 2.0 dbic minimum (at 160 o beam width) -6.0 dbic minimum cross pole gain (lhcp) (on axis) -8 dbic maximum (at 160 o beam width) -9 dbic ma...
Page 51
Gia 63 installation manual page 2-13 190-00303-05 revision t 2.8 mounting requirements the gia 63(x) mounting surface must be capable of providing structural support and electrical bond to the aircraft to minimize radiated emi and provide protection from high-intensity radiation fields (hirf). The g...
Page 52
Page 2-14 gia 63 installation manual revision t 190-00303-05 2.8.2 remote mounted stand-alone rack considerations figure 2-3 and figure b-4 show the gia 63(w) remote mounted stand-alone rack. The remote rack can be installed in a variety of locations, such as the electronics bay, under a seat, or on...
Page 53
Gia 63 installation manual page 2-15 190-00303-05 revision t figure 2-4 gia 63h standalone rack draft rev t 11/12/2010
Page 54
Page 2-16 gia 63 installation manual revision t 190-00303-05 figure 2-5 gia 63(w) standalone rack, suggested mounting locations draft rev t 11/12/2010
Page 55
Gia 63 installation manual page 3-1 190-00303-05 revision t 3 installation procedure 3.1 unpacking unit carefully unpack the equipment and make a visual inspection of the unit for evidence of damage incurred during shipment. If the unit is damaged, notify the carrier and file a claim. To justify a c...
Page 56
Page 3-2 gia 63 installation manual revision t 190-00303-05 notes 1. Non-garmin part numbers shown are not maintained by garmin and consequently are subject to change without notice. 2. Extraction of 16 and 18 awg contacts requires cutting off the wire barrel from the contact. It may also be necessa...
Page 57
Gia 63 installation manual page 3-3 190-00303-05 revision t 3.5 backshell assembly the gia 63(x) connector kit includes six garmin backshell connectors. The backshell assemblies house the configuration module/temperature sensor, if applicable. Garmin’s backshell also gives the installer the ability ...
Page 58
Page 3-4 gia 63 installation manual revision t 190-00303-05 installation instructions for the gia 63h for installation and assembly, refer to the outline and installation drawings shown in appendix b of this manual. 1. Assemble the backshell connectors, refer to section 3.5. 2. Connect backshell con...
Page 59
Gia 63 installation manual page 3-5 190-00303-05 revision t 3.8 continued airworthiness maintenance of the gia 63(x) is “on condition” for all units installed in airframes that require power interrupt category b (50ms). For airframes that require the gia 63(x) to comply with rtca/do-160d power inter...
Page 60
Page 3-6 gia 63 installation manual revision t 190-00303-05 3.8.1 category a long term power interrupt annual inspection note in order to comply with this procedure gia 63 main software version must be 5.30 or later, gia 63w main software version must be 5.21 or later, and gdu main software version ...
Page 61
Gia 63 installation manual page 4-1 190-00303-05 revision t 4 system interconnects 4.1 pin function list 4.1.1 p601 (com) view of j601 connector from back of unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 pin pin name i...
Page 62
Page 4-2 gia 63 installation manual revision t 190-00303-05 connector p601, continued pin pin name i/o 35 reserved -- 36 reserved -- 37 reserved -- 38 reserved -- 39 reserved -- 40 reserved -- 41 reserved -- 42 reserved -- 43 power ground -- 44 power ground -- * indicates active low † pin not curren...
Page 63
Gia 63 installation manual page 4-3 190-00303-05 revision t 4.1.2 p602 (vor/ils) view of j602 connector from back of unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 44 46 47 48 49 50 51 52 53 54 55 56 16 17 18 19 20 21 37 38 39 40 41 42 57 58 59 60 61 62 pin pin...
Page 64
Page 4-4 gia 63 installation manual revision t 190-00303-05 connector p602, continued pin pin name i/o 37 parallel dme 100 khz-a out 38 glideslope superflag out 39 parallel dme 100 khz-b out 40 parallel dme 100 khz-c out 41 dme common in 42 parallel dme 100 khz-d out 43 parallel dme 50 khz out 44 re...
Page 65
Gia 63 installation manual page 4-5 190-00303-05 revision t 4.1.3 p603 (main serial) view of j603 connector from back of unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 ...
Page 66
Page 4-6 gia 63 installation manual revision t 190-00303-05 connector p603, continued pin pin name i/o 37 rs-485 5 b/rs-422 out b i/o 38 reserved -- 39 can bus 2 termination -- 40 reserved -- 41 main rs-232 in 1 in 42 signal ground -- 43 main rs-232 out 1 out 44 main rs-232 in 2 in 45 signal ground ...
Page 67
Gia 63 installation manual page 4-7 190-00303-05 revision t 4.1.4 p604 (main discrete) view of j604 connector from back of unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 pin pin name i/o 1 annunciate* 22 out 2 voice ale...
Page 68
Page 4-8 gia 63 installation manual revision t 190-00303-05 connector p604, continued pin pin name i/o 40 annunciate* 17 out 41 annunciate* 18 out 42 annunciate* 19 out 43 annunciate* 20 out 44 annunciate* 21 out * indicates active low † pin not currently supported draft rev t 11/12/2010
Page 69
Gia 63 installation manual page 4-9 190-00303-05 revision t 4.1.5 p605 (i/o 1) view of j605 connector from back of unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 ...
Page 70
Page 4-10 gia 63 installation manual revision t 190-00303-05 connector p605, continued pin pin name i/o 37 discrete in* 1a in 38 discrete in* 2a in 39 discrete in* 3a in 40 discrete in* 4a in 41 discrete in* 5a in 42 discrete in* 6a in 43 discrete in* 7a in 44 discrete in* 8a in 45 discrete in* 9a i...
Page 71
Gia 63 installation manual page 4-11 190-00303-05 revision t 4.1.6 p606 (i/o 2) view of j606 connector from back of unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63...
Page 72
Page 4-12 gia 63 installation manual revision t 190-00303-05 connector p606, continued pin pin name i/o 37 heading bootstrap out x † out 38 heading bootstrap out y † out 39 heading bootstrap out z (ground) † out 40 ac roll attitude out hi † out 41 ac roll attitude out lo (ground) † out 42 ac pitch a...
Page 73
Gia 63 installation manual page 4-13 190-00303-05 revision t 4.2 power and antennas 4.2.1 power functions this section covers the power input requirements. 4.2.1.1 aircraft power pin name connector pin i/o aircraft power 1 p601 17 in aircraft power 1 p601 19 in aircraft power 1 p601 21 in aircraft p...
Page 74
Page 4-14 gia 63 installation manual revision t 190-00303-05 4.3 gia system id program the gia 63(x) utilizes a hard strapping method to assign a unit id to a unit. Unit id’s identify a unit as a #1, #2, #3, or #4 gia. Gia system id program* 1 (p604, pin 22) gia system id program* 2 (p604, pin 23) u...
Page 75
Gia 63 installation manual page 4-15 190-00303-05 revision t 4.4.1.2 rs-485/422 pin name connector pin i/o rs-485 3 a/rs-422 in a p603 27 i/o rs-485 3 b/rs-422 in b p603 28 i/o rs-485 5 a/rs-422 out a p603 36 i/o rs-485 5 b/rs-422 out b p603 37 i/o rs-485 1 a p603 23 i/o rs-485 1 b p603 24 i/o rs-48...
Page 76
Page 4-16 gia 63 installation manual revision t 190-00303-05 4.4.1.4 can bus pin name connector pin i/o can bus 1 hi p603 20 i/o can bus 1 lo p603 22 i/o can bus 1 termination p603 34 -- can bus 2 hi p603 32 i/o can bus 2 lo p603 30 i/o can bus 2 termination p603 39 -- this data bus conforms to the ...
Page 77
Gia 63 installation manual page 4-17 190-00303-05 revision t 4.5 discrete i/o pin name connector pin i/o p604 4, 5, 10, 15, 16 in discrete in p605 3, 12, 16, 50-51, 60, 74 in p604 7-9, 12- 14, 17- 21, 24 in discrete in* p605 37-46, 49, 52- 55, 59, 73 in p605 47, 68-70 out discrete out* p606 67-75, 7...
Page 78
Page 4-18 gia 63 installation manual revision t 190-00303-05 4.6 com/vor/ils/digital audio 4.6.1 com/vor/ils/digital audio function and emergency mode activation of com mic key* enables com mic audio and causes the transceiver to transmit. 500 Ω com audio and 500 Ω vor/ils audio are 100 mw audio out...
Page 79
Gia 63 installation manual page 4-19 190-00303-05 revision t 4.6.2.3 com/vor/ils audio pin name connector pin i/o com 500 Ω audio out hi p601 9 out com 500 Ω audio out lo p601 10 out vor/loc 500 Ω audio out hi p602 16 out vor/loc 500 Ω audio out lo p602 17 out voice alert 500 Ω audio out hi p604 2 o...
Page 80
Page 4-20 gia 63 installation manual revision t 190-00303-05 4.7 vor/ils indicator 4.7.1 vor/ils indicator function the vor/ils indicator displays both lateral and vertical, to/from indications, lateral flags, vertical flags, and superflags. Vor/loc composite out is a standard vor/localizer composit...
Page 81
Gia 63 installation manual page 4-21 190-00303-05 revision t 4.7.2.3 to/from pin name connector pin i/o vor/loc +to p602 1 out vor/loc +from (vor/loc common) vor/loc +from (nav common) (011-01105-20 and 011-01105-30 only) p602 2 out the output is capable of driving up to three 200 Ω meter loads. Whe...
Page 82
Page 4-22 gia 63 installation manual revision t 190-00303-05 4.7.2.6 vor/loc composite pin name connector pin i/o vor/loc composite out p602 8 out with a standard vor test signal applied, vor/loc composite out is 0.5 ±0.1 v rms into a 10 k Ω load. With a standard localizer centering test signal appl...
Page 83
Gia 63 installation manual page 4-23 190-00303-05 revision t 4.8 rmi/obi 4.8.1 rmi/obi function the vor obi output provides bearing information from the active waypoint based upon the vor receiver. When a localizer channel is tuned on the vloc window, there is a bit in the data stream set to indicat...
Page 84
Page 4-24 gia 63 installation manual revision t 190-00303-05 4.9 dme tuning and adf 4.9.1 dme tuning function the gia 63(x) can channel a dme based on the tuned vloc frequency. The gia 63(x) outputs 2 of 5, bcd or slip parallel dme and king serial dme channeling format. When dme common is held low, ...
Page 85
Gia 63 installation manual page 4-25 190-00303-05 revision t 4.9.2.2 king serial dme interface pin name connector pin i/o king serial dme clock p602 18 out king serial dme data p602 19 out king serial rnav request p602 20 in king serial rnav* mode p602 21 in main king serial dme data p606 59 i/o mai...
Page 86
Page 4-26 gia 63 installation manual revision t 190-00303-05 4.10 auto pilot 4.10.1 flight instruments pin name connector pin i/o flight director pitch +up p605 8 in flight director pitch +down p605 9 in flight director roll +right p605 10 in flight director roll +left p605 11 in inputs from afcs th...
Page 87
Gia 63 installation manual page 4-27 190-00303-05 revision t 4.10.2 automatic flight control system outputs pin name connector pin i/o analog roll steering hi p606 34 out analog roll steering lo (ground) p606 36 -- variable-amplitude output, which is proportional to the aircraft roll command from th...
Page 88
Page 4-28 gia 63 installation manual revision t 190-00303-05 4.10.3 main deviation outputs pin name connector pin i/o main lateral deviation +left p605 17 out main lateral deviation +right (main common) p605 18 out main vertical deviation +up p605 23 out main vertical deviation +down (main common) p...
Page 89
Gia 63 installation manual page 4-29 190-00303-05 revision t 4.10.4 remote annunciate data bus pin name connector pin i/o remote annunciate clock p606 53 in remote annunciate data p606 54 in remote annunciate sync p606 55 in these inputs read the remote annunciate data bus that the autopilot uses to...
Page 90
Page 4-30 gia 63 installation manual revision t 190-00303-05 this page intentionally left blank draft rev t 11/12/2010
Page 91
Gia 63 installation manual page a-1 190-00303-05 revision t appendix a gia 63 main boot block uploading instructions note this appendix applies to the gia 63 only, and does not apply to the gia 63w or gia 63h. A.1 introduction this appendix contains instructions on how to upgrade main boot block sof...
Page 92
Page a-2 gia 63 installation manual revision t 190-00303-05 10. Use the fms knob to highlight gia 6x software. 11. Press the lru softkey and highlight ‘gia 1’. 12. Press the ent key to begin loading software. 13. The boot block version should now appear on the mfd. 14. If gia main boot block version...
Page 93
Gia 63 installation manual page a-3 190-00303-05 revision t 11. Confirm update completion and press the ent key. 12. On the mfd use the fms knob to turn to the system status page. 13. Highlight ‘gia 1’. 14. Verify ‘g1000 gia 6x sys’ is being reported in the description field. 15. Power down the g100...
Page 94
Page a-4 gia 63 installation manual revision t 190-00303-05 this page intentionally left blank draft rev t 11/12/2010