Garmin GIA 63 Installation Manual

Other manuals for GIA 63: Installation Manual, Installation Manual

Summary of GIA 63

  • Page 1

    The following fi les have been archived under the aboce archive filename. Filename file contents date: drafter: checker: project engineer: released by: title: part no: size a scale: n/a rev. Sheets of revisions specification control drawing rev. Date description eco no. Garmin ltd. Or its subsidiari...

  • Page 2: Gia 63/gia 63W

    190-00303-05 october, 2006 revision h gia 63/gia 63w installation manual.

  • Page 3

    Page a gia 63/gia 63w installation manual revision h 190-00303-05 © copyright 2003-2006 garmin ltd. Or its subsidiaries all rights reserved except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, fo...

  • Page 4

    Gia 63/gia 63w installation manual page i 190-00303-05 revision h this manual reflects the operation of main software version 4.00 for the gia 63 and main software version 5.00 for the gia 63w. Some differences in operation may be observed when comparing the information in this manual to earlier or ...

  • Page 5

    Page ii gia 63/gia 63w installation manual revision h 190-00303-05 this page intentionally left blank.

  • Page 6

    Gia 63/gia 63w installation manual page iii 190-00303-05 revision h table of contents paragraph page 1 general description..............................................................................................................1-1 1.1 introduction...................................................

  • Page 7

    Page iv gia 63/gia 63w installation manual revision h 190-00303-05 paragraph page appendix a gia 63 main boot block uploading instructions................................. A-1 a.1 introduction...............................................................................................................

  • Page 8

    Gia 63/gia 63w installation manual page v 190-00303-05 revision h gia 63 hardware mod level history the following table identifies hardware modification (mod) levels for the gia 63. Mod levels are listed with the associated service bulletin number, service bulletin date, and the purpose of the modif...

  • Page 9

    Page vi gia 63/gia 63w installation manual revision h 190-00303-05 gia 63w hardware mod level history the following table identifies hardware modification (mod) levels for the gia 63w. Mod levels are listed with the associated service bulletin number, service bulletin date, and the purpose of the mo...

  • Page 10

    Gia 63/gia 63w installation manual page 1-1 190-00303-05 revision h 1 general description 1.1 introduction this manual presents mechanical and electrical installation requirements for installing the gia 63(w) as part of the g1000 integrated flight deck. The gia 63(w) can be integrated into a variety...

  • Page 11

    Page 1-2 gia 63/gia 63w installation manual revision h 190-00303-05 1.3 interface summary 1.3.1 primary interfaces the gia 63(w) is designed as an open architecture system that provides the following interfaces: • 1 dedicated ethernet high-speed data bus (hsdb) input/output channel • 2 controller ar...

  • Page 12

    Gia 63/gia 63w installation manual page 1-3 190-00303-05 revision h 1.4 technical specifications 1.4.1 environmental qualification form it is the responsibility of the installing agency to obtain the latest revision of the gia 63(w) environmental qualification form. This form is available directly f...

  • Page 13

    Page 1-4 gia 63/gia 63w installation manual revision h 190-00303-05 1.4.5 waas specific gps specifications (gia 63w only) characteristics specifications number of channels 15 (12 gps and 3 gps/waas/sbas) frequency 1575.42 mhz l1, c/a code sensitivity (acquisition) -116 dbm to -134.5 dbm gps -116 dbm...

  • Page 14

    Gia 63/gia 63w installation manual page 1-5 190-00303-05 revision h 1.4.6 com transceiver specifications characteristics specifications audio output 100 mw minimum into a 500 Ω load. Audio response less than 6 db of variation between 350 and 2500 hz. Audio distortion the distortion in the receiver a...

  • Page 15

    Page 1-6 gia 63/gia 63w installation manual revision h 190-00303-05 1.4.7 vor specifications characteristics specifications receiver audio sensitivity at -103.5 dbm (s+n)/n shall not be less than 6 db. Course deviation sensitivity at –103.5 dbm deviation output shall not be less than 60% of standard...

  • Page 16

    Gia 63/gia 63w installation manual page 1-7 190-00303-05 revision h 1.4.8 loc specifications characteristics specifications receiver audio sensitivity at -103.5 dbm (s+n)/n shall not be less than 6 db. Course deviation sensitivity at –103.5 dbm, deviation output shall not be less than 60% of standar...

  • Page 17

    Page 1-8 gia 63/gia 63w installation manual revision h 190-00303-05 1.4.9 glideslope specifications characteristics specifications sensitivity at –93 dbm, deviation output shall not be less than 60% of standard deflection when glideslope deviation test signal is applied. Centering accuracy 0 ± .0091...

  • Page 18

    Gia 63/gia 63w installation manual page 1-9 190-00303-05 revision h 1.5 license requirements the telecommunications act of 1996, effective february 8, 1996, provides the fcc discretion to eliminate radio station license requirements for aircraft and ships. The gia 63(w) installation must comply with...

  • Page 19

    Page 1-10 gia 63/gia 63w installation manual revision h 190-00303-05 1.6.1 gia 63 tso/etso compliance function tso/etso category applicable lru sw part numbers automatic pilots tso-c9c all 006-b0190-() except 006-b0190-00 through 006-b0190-19 glideslope receiver tso-c34e etso-2c34f 006-b0190-() loca...

  • Page 20

    Gia 63/gia 63w installation manual page 1-11 190-00303-05 revision h 1.6.2 gia 63w tso/etso compliance function tso/etso category applicable lru sw part numbers applicable cld part numbers all 006-c0084-() except 006-c0084-00 006-c0072-() 006-c0085-() automatic pilots tso-c9c all 006-b0544-() except...

  • Page 21

    Page 1-12 gia 63/gia 63w installation manual revision h 190-00303-05 gia 63w tso/etso compliance, continued function tso/etso category applicable lru sw part numbers applicable cld part numbers all 006-c0084-() except 006-c0084-00 006-c0072-() 006-c0085-() all 006-c0039-() except 00c-c0039-00 throug...

  • Page 22

    Gia 63/gia 63w installation manual page 1-13 190-00303-05 revision h gia 63w tso/etso compliance, continued function tso/etso category applicable lru sw part numbers applicable cld part numbers all 006-c0084-() except 006-c0084-00 006-c0072-() 006-c0085-() taws tso-c151b class b all 006-b0544-() exc...

  • Page 23

    Page 1-14 gia 63/gia 63w installation manual revision h 190-00303-05 1.6.3 gia 63 tso/etso deviations tso deviation 1. Garmin was granted a deviation from tso-c9c to use sae as 402b instead of as- 402a. The justification for this deviation is to use the latest accepted environmental standards. 2. Ga...

  • Page 24

    Gia 63/gia 63w installation manual page 1-15 190-00303-05 revision h tso deviations, continued tso deviation 1. Garmin was granted a deviation from tso-c38d to use do-160d change 3 instead of do-160b, and do-178b instead of do-178a. The justification for this deviation is to use the latest accepted ...

  • Page 25

    Page 1-16 gia 63/gia 63w installation manual revision h 190-00303-05 tso deviations, continued tso deviation 1. Garmin was granted a deviation from tso-c129a to use do-160d change 3 instead of do-160c. The justification for this deviation is to use the latest accepted environmental and software stan...

  • Page 26

    Gia 63/gia 63w installation manual page 1-17 190-00303-05 revision h etso deviations etso deviation deviate from ed-72a 3.2.2.1.F (list item 3) and 3.2.2.4.J.4 to eliminate the annunciation for pending cdi scale change 3.0 nm from the faf. Deviate from ed-72a 3.2.2.4.J.3 to extend automatic cdi sens...

  • Page 27

    Page 1-18 gia 63/gia 63w installation manual revision h 190-00303-05 1.6.4 gia 63w tso/etso deviations tso/etso deviation 1. Garmin was granted a deviation from tso-c9c to use sae as 402b instead of as- 402a. The justification for this deviation is to use the latest accepted environmental standards....

  • Page 28

    Gia 63/gia 63w installation manual page 1-19 190-00303-05 revision h tso/etso deviations, continued tso/etso deviation 1. Garmin was granted a deviation from tso-c145a to use do-160e instead of do-160d. The justification for this deviation is to use the latest accepted environmental standards. Tso-c...

  • Page 29

    Page 1-20 gia 63/gia 63w installation manual revision h 190-00303-05 1.6.5 afm/afms/poh considerations per tso-c9c deviation, the applicable afm, afms, and/or poh shall list autopilot engagement envelope for the certified aircraft. Per tso-c52b deviation, the applicable afm, afms, and/or poh shall s...

  • Page 30

    Gia 63/gia 63w installation manual page 1-21 190-00303-05 revision h 1.6.6 other regulatory criteria (gia 63) rtca/do-178b level b, c, d (software) eurocae ed 12b (software) rtca/do-160d (environmental conditions) eurocae ed 14d (environmental conditions) rtca/do-208 class a1 (gps) rtca/do-186a clas...

  • Page 31

    Page 1-22 gia 63/gia 63w installation manual revision h 190-00303-05 1.8 limited warranty this garmin product is warranted to be free from defects in materials or workmanship for two years from the date of purchase. Within this period, garmin will at its sole option, repair or replace any components...

  • Page 32

    Gia 63/gia 63w installation manual page 2-1 190-00303-05 revision h 2 installation overview 2.1 introduction this section provides hardware equipment information for installing the gia 63(w), related hardware, and antennas. Installation of the gia 63(w) should follow the aircraft tc or stc requireme...

  • Page 33

    Page 2-2 gia 63/gia 63w installation manual revision h 190-00303-05 2.1.3 additional equipment required the following installation accessories are required but not provided: com antenna: shall meet tso-c37(), c38(), and c-169()*. Broad band, 50 Ω , vertically polarized with coaxial cable gps antenna...

  • Page 34

    Gia 63/gia 63w installation manual page 2-3 190-00303-05 revision h 2.1.3.1 required antennas for the gia 63 antennas used with the gia 63 (non-waas) must meet the antenna specifications shown in section 2.6. In addition, tso-c144 antennas can also meet tso-c129a requirements for the gia 63 (non-waa...

  • Page 35

    Page 2-4 gia 63/gia 63w installation manual revision h 190-00303-05 2.2 installation considerations the gia 63(w) interfaces with the g1000 system and with various avionics equipment. Fabrication of a wiring harness is required. Sound mechanical and electrical methods and practices are required for ...

  • Page 36

    Gia 63/gia 63w installation manual page 2-5 190-00303-05 revision h 2.2.5 glideslope antenna location the gia 63(w) glideslope antenna should be well removed from all projections, engines and propellers. It should have a clear line of sight if possible. 2.2.6 electrical bonding no special precaution...

  • Page 37

    Page 2-6 gia 63/gia 63w installation manual revision h 190-00303-05 2.3 rack considerations a location away from heating vents or other sources of heat generation is optimal. The gia 63(w) is to be mounted using the g1000 integrated flight deck rack system. The unit may be mounted remotely if desire...

  • Page 38

    Gia 63/gia 63w installation manual page 2-7 190-00303-05 revision h 2.5 cooling air the gia 63(w) meets all tso requirements without external cooling. However, as with all electronic equipment, lower operating temperatures extend equipment life. On the average, reducing the operating temperature by ...

  • Page 39

    Page 2-8 gia 63/gia 63w installation manual revision h 190-00303-05 2. Electrical characteristics lna supply voltage 4.5 ± 0.5 v dc lna supply current 20 ma maximum lna operating frequency 1575.42 ± 2.00 mhz lna gain 20 db maximum, 12db minimum lna noise figure 3.0 db maximum lna output vswr (50 Ω )...

  • Page 40

    Gia 63/gia 63w installation manual page 2-9 190-00303-05 revision h 2.8 mounting requirements the gia 63(w) is to be mounted using the g1000 rack system. The unit may also be mounted remotely if desired. Aircraft manufacturer must fabricate any additional mounting equipment needed, use outline and i...

  • Page 41

    Page 2-10 gia 63/gia 63w installation manual revision h 190-00303-05 this page intentionally left blank.

  • Page 42

    Gia 63/gia 63w installation manual page 3-1 190-00303-05 revision h 3 installation procedure 3.1 unpacking unit carefully unpack the equipment and make a visual inspection of the unit for evidence of damage incurred during shipment. If the unit is damaged, notify the carrier and file a claim. To jus...

  • Page 43

    Page 3-2 gia 63/gia 63w installation manual revision h 190-00303-05 notes 1. Non-garmin part numbers shown are not maintained by garmin and consequently are subject to change without notice. 2. Extraction of 16 and 18 awg contacts requires cutting off the wire barrel from the contact. It may also be...

  • Page 44

    Gia 63/gia 63w installation manual page 3-3 190-00303-05 revision h 3. Contacts for the 78, 62, and 44 pin connectors must be crimped onto the individual wires of the aircraft wiring harness. Tables 3-1 and 3-2 list contact part numbers (for reference) and recommended crimp tools. 3.5 backshell asse...

  • Page 45

    Page 3-4 gia 63/gia 63w installation manual revision h 190-00303-05 3.7 post installation configuration & checkout all configuration and checkout procedures take place upon completion of the installation of the g1000 system. The gdu serves as the graphics user interface to the installer configuring ...

  • Page 46

    Gia 63/gia 63w installation manual page 4-1 190-00303-05 revision h 4 system interconnects 4.1 pin function list 4.1.1 p601 (com) view of j601 connector from back of unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 pin pi...

  • Page 47

    Page 4-2 gia 63/gia 63w installation manual revision h 190-00303-05 connector p601, continued pin pin name i/o 35 reserved -- 36 reserved -- 37 reserved -- 38 reserved -- 39 reserved -- 40 reserved -- 41 reserved -- 42 reserved -- 43 power ground -- 44 power ground --.

  • Page 48

    Gia 63/gia 63w installation manual page 4-3 190-00303-05 revision h 4.1.2 p602 (vor/ils) view of j602 connector from back of unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 44 46 47 48 49 50 51 52 53 54 55 56 16 17 18 19 20 21 37 38 39 40 41 42 57 58 59 60 61 62...

  • Page 49

    Page 4-4 gia 63/gia 63w installation manual revision h 190-00303-05 connector p602, continued pin pin name i/o 38 glideslope superflag out 39 parallel dme 100 khz-b out 40 parallel dme 100 khz-c out 41 dme common in 42 parallel dme 100 khz-d out 43 parallel dme 50 khz out 44 spare -- 45 parallel dme...

  • Page 50

    Gia 63/gia 63w installation manual page 4-5 190-00303-05 revision h 4.1.3 p603 (main serial) view of j603 connector from back of unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 5...

  • Page 51

    Page 4-6 gia 63/gia 63w installation manual revision h 190-00303-05 connector p603, continued pin pin name i/o 37 rs-485 5 b/rs-422 out b i/o 38 reserved -- 39 can bus 2 termination -- 40 reserved -- 41 main rs-232 in 1 in 42 signal ground -- 43 main rs-232 out 1 out 44 main rs-232 in 2 in 45 signal...

  • Page 52

    Gia 63/gia 63w installation manual page 4-7 190-00303-05 revision h 4.1.4 p604 (main discrete) view of j604 connector from back of unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 pin pin name i/o 1 annunciate* 22 out 2 v...

  • Page 53

    Page 4-8 gia 63/gia 63w installation manual revision h 190-00303-05 connector p604, continued pin pin name i/o 40 annunciate* 17 out 41 annunciate* 18 out 42 annunciate* 19 out 43 annunciate* 20 out 44 annunciate* 21 out.

  • Page 54

    Gia 63/gia 63w installation manual page 4-9 190-00303-05 revision h 4.1.5 p605 (i/o 1) view of j605 connector from back of unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 6...

  • Page 55

    Page 4-10 gia 63/gia 63w installation manual revision h 190-00303-05 connector p605, continued pin pin name i/o 37 discrete in* 1a in 38 discrete in* 2a in 39 discrete in* 3a in 40 discrete in* 4a in 41 discrete in* 5a in 42 discrete in* 6a in 43 discrete in* 7a in 44 discrete in* 8a in 45 discrete ...

  • Page 56

    Gia 63/gia 63w installation manual page 4-11 190-00303-05 revision h 4.1.6 p606 (i/o 2) view of j606 connector from back of unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 ...

  • Page 57

    Page 4-12 gia 63/gia 63w installation manual revision h 190-00303-05 connector p606, continued pin pin name i/o 37 heading bootstrap out x out 38 heading bootstrap out y out 39 heading bootstrap out z (ground) out 40 ac roll attitude out hi out 41 ac roll attitude out lo (ground) out 42 ac pitch att...

  • Page 58

    Gia 63/gia 63w installation manual page 4-13 190-00303-05 revision h 4.2 power and antennas 4.2.1 power functions this section covers the power input requirements. 4.2.1.1 aircraft power pin name connector pin i/o aircraft power 1 p601 17 in aircraft power 1 p601 19 in aircraft power 1 p601 21 in ai...

  • Page 59

    Page 4-14 gia 63/gia 63w installation manual revision h 190-00303-05 4.3 gia system id program the gia 63(w) utilizes a hard strapping method to assign a unit id to a unit. Unit id’s identify a unit as a #1, #2, #3, or #4 gia. Gia system id program 1 (p604, pin 22) gia system id program 2 (p604, pin...

  • Page 60

    Gia 63/gia 63w installation manual page 4-15 190-00303-05 revision h 4.4.1.2 rs-485/422 pin name connector pin i/o rs-485/422 in a p603 27 in rs-485/422 in b p603 28 in rs-485/422 out a p603 36 out rs-485/422 out b p603 37 out gea rs-485 1 a p603 23 i/o gea rs-485 1 b p603 24 i/o gea rs-485 2 a p603...

  • Page 61

    Page 4-16 gia 63/gia 63w installation manual revision h 190-00303-05 the main and vor/ils arinc 429 outputs conform to arinc 429 electrical specifications when loaded with up to 5 standard arinc 429 receivers. 4.4.1.4 can bus pin name connector pin i/o can bus 1 hi p603 20 i/o can bus 1 lo p603 22 i...

  • Page 62

    Gia 63/gia 63w installation manual page 4-17 190-00303-05 revision h 4.5 discrete i/o pin name connector pin i/o p604 4, 5, 10, 15, 16 in discrete in p605 3, 12, 16, 50-51, 60, 74 in p604 7-9, 12- 14, 17- 21, 24 in discrete in* p605 37-46, 49, 52- 55, 59, 73 in p605 47, 68-70 out discrete out* p606 ...

  • Page 63

    Page 4-18 gia 63/gia 63w installation manual revision h 190-00303-05 4.6 com/vor/ils/digital audio 4.6.1 com/vor/ils/digital audio function and emergency mode activation of com mic key enables com mic audio and causes the transceiver to transmit. 500 Ω com audio and 500 Ω vor/ils audio are 100 mw au...

  • Page 64

    Gia 63/gia 63w installation manual page 4-19 190-00303-05 revision h when a 125 mv rms signal at 1000 hz is applied to the intercom mic input, the level on the com audio output is not less than 7.07 v rms . 4.6.2.3 com/vor/ils audio pin name connector pin i/o com 500 Ω audio out hi p601 9 out com 50...

  • Page 65

    Page 4-20 gia 63/gia 63w installation manual revision h 190-00303-05 4.7 vor/ils indicator 4.7.1 vor/ils indicator function the vor/ils indicator displays both lateral and vertical, to/from indications, lateral flags, vertical flags, and superflags. Vor/loc composite out is a standard vor/localizer ...

  • Page 66

    Gia 63/gia 63w installation manual page 4-21 190-00303-05 revision h 4.7.2.3 to/from pin name connector pin i/o vor/loc +to p602 1 out vor/loc +from (vor/loc common) p602 2 -- the output is capable of driving up to three 200 Ω meter loads. When indicating to, the output is +225 ±75 mv dc. When indic...

  • Page 67

    Page 4-22 gia 63/gia 63w installation manual revision h 190-00303-05 4.7.2.7 ils energize pin name connector pin i/o ils energize p602 29 out inactive: floating (can be pulled up to externally sourced vout in the range 0 ≤ vout ≤ 33vdc) leakage current in the inactive state is typically ≤ 10 ua to g...

  • Page 68

    Gia 63/gia 63w installation manual page 4-23 190-00303-05 revision h 4.9 dme tuning and adf 4.9.1 dme tuning function the gia 63(w) can channel a dme based on the tuned vloc frequency. The gia 63(w) outputs 2 of 5, bcd or slip parallel dme and king serial dme channeling format. When dme common is he...

  • Page 69

    Page 4-24 gia 63/gia 63w installation manual revision h 190-00303-05 4.9.2.2 king serial dme interface pin name connector pin i/o king serial dme clock p602 18 out king serial dme data p602 19 out king serial rnav request p602 20 in king serial rnav mode p602 21 in main king serial dme data p606 59 ...

  • Page 70

    Gia 63/gia 63w installation manual page 4-25 190-00303-05 revision h 4.10.2 flight instruments pin name connector pin i/o flight director pitch +up p605 8 in flight director pitch +down p605 9 in flight director pitch +right p605 10 in flight director pitch +left p605 11 in inputs from afcs that dir...

  • Page 71

    Page 4-26 gia 63/gia 63w installation manual revision h 190-00303-05 4.10.4 26 volt ac references pin name connector pin i/o 26 vac vertical gyro ref hi p606 1 in 26 vac vertical gyro ref lo p606 2 in 26 vac adf ref hi p606 3 in 26 vac adf ref lo p606 4 in 26 vac afcs ref hi p606 5 in 26 vac afcs re...

  • Page 72

    Gia 63/gia 63w installation manual page 4-27 190-00303-05 revision h 4.10.5 inputs from gyros pin name connector pin i/o heading x p606 14 in heading y p606 15 in heading z (ground) p606 16 -- inputs heading information from a directional gyro. 3-wire synchro magnetic heading input, with heading z g...

  • Page 73

    Page 4-28 gia 63/gia 63w installation manual revision h 190-00303-05 4.10.6 automatic flight control system outputs pin name connector pin i/o analog roll steering hi p606 34 out analog roll steering lo (ground) p606 36 -- variable-amplitude output, which is proportional to the aircraft roll command...

  • Page 74

    Gia 63/gia 63w installation manual page 4-29 190-00303-05 revision h pin name connector pin i/o course datum hi p606 48 out course datum lo (ground) p606 49 -- outputs course datum (ac or dc) information to afcs. Ac dc frequency: 400 hz ±10% -- amplitude: 0 to 11.8 vrms max -15 to +15 vdc load imped...

  • Page 75

    Page 4-30 gia 63/gia 63w installation manual revision h 190-00303-05 pin name connector pin i/o main lateral +flag p605 19 out main lateral -flag (main common) p605 20 out main vertical +flag p605 25 out main vertical –flag (main common) p605 26 out the flag output is capable of driving up to three ...

  • Page 76

    Gia 63/gia 63w installation manual page a-1 190-00303-05 revision h appendix a gia 63 main boot block uploading instructions note this appendix applies to the gia 63 only, and does not apply to the gia 63w. A.1 introduction this appendix contains instructions on how to upgrade main boot block softwa...

  • Page 77

    Page a-2 gia 63/gia 63w installation manual revision h 190-00303-05 10. Use the fms knob to highlight gia 6x software. 11. Press the lru softkey and highlight ‘gia 1’. 12. Press the ent key to begin loading software. 13. The boot block version should now appear on the mfd. 14. If gia main boot block...

  • Page 78

    Gia 63/gia 63w installation manual page a-3 190-00303-05 revision h 11. Confirm update completion and press the ent key. 12. On the mfd use the fms knob to turn to the system status page. 13. Highlight ‘gia 1’. 14. Verify ‘g1000 gia 6x sys’ is being reported in the description field. 15. Power down ...

  • Page 79

    Page a-4 gia 63/gia 63w installation manual revision h 190-00303-05 this page intentionally left blank.

  • Page 80

    Appendix b outline & installation drawings gia 63/gia 63w installation manual page b-1 (page b-2 blank) 190-00303-05 revision h 8.84 224.6 6.30 160.0 7.26 184.4 8.35 212.0 9.73 247.2 9.23 234.4 4.8 122 2.9 74 .44 typ 11.1 .48 typ 12.2 3.79 96.2 .44 typ 11.1 1.8 46 air gps com p601 p604 p603 p606 g/s...

  • Page 81

    Appendix b outline & installation drawings gia 63/gia 63w installation manual page b-3 (page b-4 blank) 190-00303-05 revision h figure b-2. Gia 63(w) installation drawing.

  • Page 82

    Appendix c interconnect examples gia 63/gia 63w installation manual page c-1 (page c-2 blank) 190-00303-05 revision h figure c-1. Gia 63(w) example interconnect (sheet 1 of 7).

  • Page 83

    Appendix c interconnect examples gia 63/gia 63w installation manual page c-3 (page c-4 blank) 190-00303-05 revision h figure c-1. Gia 63(w) example interconnect (sheet 2 of 7).

  • Page 84

    Appendix c interconnect examples gia 63/gia 63w installation manual page c-5 (page c-6 blank) 190-00303-05 revision h figure c-1. Gia 63(w) example interconnect (sheet 3 of 7).

  • Page 85

    Appendix c interconnect examples gia 63/gia 63w installation manual page c-7 (page c-8 blank) 190-00303-05 revision h figure c-1. Gia 63(w) example interconnect (sheet 4 of 7).

  • Page 86

    Appendix c interconnect examples gia 63/gia 63w installation manual page c-9 (page c-10 blank) 190-00303-05 revision h figure c-1. Gia 63(w) example interconnect (sheet 5 of 7).

  • Page 87

    Appendix c interconnect examples gia 63/gia 63w installation manual page c-11 (page c-12 blank) 190-00303-05 revision h figure c-1. Gia 63(w) example interconnect (sheet 6 of 7).

  • Page 88

    Appendix c interconnect examples gia 63/gia 63w installation manual page c-13 (page c-14 blank) 190-00303-05 revision h figure c-1. Gia 63(w) example interconnect (sheet 7 of 7).