1. DL manuals
  2. Garmin
  3. Marine GPS System
  4. GPS 17 Series
  5. Installation Instructions Manual

Garmin GPS 17 Series Installation Instructions Manual

Manual is about: Technical Specifications

Summary of GPS 17 Series

  • Page 1

    Gpsmap ® 2106/2110 & gps 17 installation instructions graphic to be replaced.

  • Page 2

    All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded, or stored in any storage medium, for any purpose without the express prior written consent of garmin. Garmin hereby grants permission to download a singl...

  • Page 3

    1 i nstallation i nstructions gpsmap 2106/2110 & gps 17 i ntroduction the gpsmap 2106/2110 multi-function display (mfd) and gps 17 must be properly installed according to the following instructions for the best possible performance. To complete the installation, you need the appropriate fasteners, t...

  • Page 4

    2 i nstallation i nstructions gpsmap 2106/2110 & gps 17 bail mount bail mount mounting knobs i nstallation i nstructions surface mounting the gpsmap 2106/2110 tools • drill and drill bit • screwdriver • pencil • mounting hardware (not included) note: mounting hardware (fasteners) not included. Mount...

  • Page 5

    3 i nstallation i nstructions gpsmap 2106/2110 & gps 17 230mm 208mm ...

  • Page 6

    4 i nstallation i nstructions gpsmap 2106/2110 & gps 17 installing the gps 17 you can install flush mount or install the gps 17 on any standard 1" o.D. (outer dimension), 14 threads-per-inch marine mount. When mounting the gps 17, the cable can be run externally, through the mounting panel, or throug...

  • Page 7

    5 i nstallation i nstructions gpsmap 2106/2110 & gps 17 to attach the enclosed pole mount to the gps 17: 1. Thread the cable though the pole mount. 2. Align the tab on the mount to the notch on the gps 17. 3. Use the enclosed screws to secure the mount to the base. Attaching the pole mount to the gp...

  • Page 8

    6 i nstallation i nstructions gpsmap 2106/2110 & gps 17 wiring and cables the gpsmap 2106/2110 comes with an 18-pin power/data cable. For some installations, it may be necessary to drill 1.25" (31.7 mm) holes to route the connector end of the cables. Garmin rubber grommets are provided to cover the ...

  • Page 9

    7 i nstallation i nstructions gpsmap 2106/2110 & gps 17 canet wiring for the gpsmap 2106/2110 canet ® is a high-speed sonar network. Using the canet interface optimizes the performance of the canet-compatible units. Canet compatible unit device features, such as ultrascroll™, are affected if a seria...

  • Page 10

    8 i nstallation i nstructions gpsmap 2106/2110 & gps 17 power/data cable wiring the following pages contain several wiring diagrams. The first diagram on the next page is a simple diagram showing the gpsmap 2106/2110 mfd using the 18-pin power/data wiring harness and the gps 17. If two gpsmap 2106/21...

  • Page 11

    9 i nstallation i nstructions gpsmap 2106/2110 & gps 17 gpsmap 2106/2110 and gps 17 basic wiring wire color gps 17 gps/waas sensor black (ground) yellow (on) red (power) blue (data in) black orange red green white + - white (data out) wire color battery 10-33 volts dc 3 a fus...

  • Page 12

    10 i nstallation i nstructions gpsmap 2106/2110 & gps 17 garmin gpsmap 2106/2110 gps 17 garmin gpsmap 2106/2110 optional alarm wiring the gpsmap 2106/2110 has an alarm circuit that can be used with a lamp, a horn, or both to alert you when the unit displays a message. The alarm circuit pulls low whe...

  • Page 13

    11 i nstallation i nstructions gpsmap 2106/2110 & gps 17 final wiring connection after all the wiring is complete, plug the 18-pin harness into the center connector on the backside of the gpsmap 2106/2110. The 5-pin port on the right side is intended for future interfacing features and does not requ...

  • Page 14

    12 i nstallation i nstructions gpsmap 2106/2110 & gps 17.

  • Page 15

    13 i nstallation i nstructions gpsmap 2106/2110 & gps 17 flush mount drilling template drill this 3/4" (19 mm) hole if the coax is going to be installed through the mounting panel drill using a 11/64" (4.5 mm) drill bit.

  • Page 16

    © copyright 2006 garmin ltd. Or its subsidiaries garmin international, inc. 1200 east 151 st street, olathe, kansas 66062, u.S.A. Garmin (europe) ltd. Unit 5, the quadrangle, abbey park industrial estate, romsey, so51 9dl, u.K. Garmin corporation no. 68, jangshu 2 nd road, shijr, taipei county, taiw...