Goldline Aqua Pod Operation manual - Charging The Aqua Pod
other systems in the neighborhood, and likewise, their remotes will not affect
your system. To teach the ID code to the Aqua Pod remote unit:
a.
On any Aqua Logic display/keypad unit
press the “Menu” button (possibly multiple
times) until “Settings Menu” is displayed.
b.
Press “” (again, possibly multiple
times) until “Teach Wireless” is displayed.
c.
Press the “+” button to start the teaching
process.
d.
Press and hold any button on the Aqua Pod
remote for 4 seconds. The Aqua Logic dis-
play should say “Teach Wireless: Success-
ful”.
4.
Installation is complete:
you can now use the Aqua Pod remote.
Charging the Aqua Pod
Plug the included charging stand into a standard 120VAC wall outlet, away from the
pool area. It is not recommended that you use an extension cord with this product
near the pool. Slide the Aqua Pod into the charging stand and charge for at least 5
hours before attempting to operate remotely. Charge the Aqua Pod at temperatures
between 32ºF and 113ºF (0º - 45ºC). The Aqua Pod can be used while in the stand no
matter what state the battery is in. A fully charged battery will provide about 300 one-
minute uses under typical conditions.
About battery power:
When the Aqua Pod is not in the charging stand, the unit uses battery power and will
take steps to extend battery life. After one minute of no button presses by the user,
the unit will briefly display “Shutting down to save battery power” and will go into
“sleep” mode. If the “System Off” button is pressed while the Aqua Pod is sleeping,
all Aqua Logic outputs will turn off immediately. For all other buttons, the Aqua Pod
will wake only. Once awake, any subsequent button presses will perform their normal
functions.
When the Aqua Pod is in the charging stand, the unit uses wall power while it also
charges the battery. It will always be “awake”, as long as it's sitting in the charger.
Note that the battery will slowly lose charge if the unit is not plugged into charging
stand even if it is not used. The battery should be charged every 4-5 days, depending
on usage.
The Aqua Pod will display a series of information about its status and the status of the
battery. Refer to the “Operating Status” section of this manual for an explanation of
each of these displays.
NOTE: The built-in Lithium Ion battery pack is not replaceable and should offer at
least 5 years of service.
2
9
Settings
Menu
Teach Wireless:
+ to start
then the radio signal may be too weak—try moving closer to the Aqua Logic main
control unit base station.
9.
Display Error x
call 888-921-7665
An internal problem has occurred in the Aqua Pod. Call the Goldline Tech sup-
port department (Monday through Friday, from 8AM to 8PM eastern time) to find
out how to obtain a replacement wireless remote display/keypad.
10. Blank screen or erroneous display after "wake" up:
If the Aqua Pod's screen is blank or displays the wrong information after "wake"
up, press the MENU button. This will refresh the display and should correct the
problem.
11. Softkeys do not respond:
There are sporadic reports of Softkeys occasionally not functioning while other
keys continue to function normally. If this happens, reset the Aqua Pod by
pressing the "System Off" button (bottommost key on the Aqua Pod) while
pressing and holding the "
go through a brief start up routine before functioning normally.
12. "Refreshing Display" continuously displayed:
If the Aqua Logic's power is off, the Aqua Pod will display this message. In this
case, returning power to the Aqua Logic or "reteaching" (see Installation instruc-
tions) the Aqua Pod will correct the problem.
13. Teach fails:
The Aqua Pod can only be used with the AQL2-BASE-RF base station. Be
certain that the proper base station is being used. When teaching, be certain that
the Aqua Logic control shows "press and hold wireless button" and that the
Aqua Pod is close to the Aqua Logic.
14. Interference with 900MHz devices (baby monitors, video monitors, etc.):
To determine if there is a problem, be certain that the interference stops when the
Aqua Logic's power is turned off. If so, try different channels on the affected
device. Also, try changing the Aqua Logic's wireless channel. This is described
in the Aqua Logic Installation manual. Note that some interference may not be
able to be resolved.
15. Frequent "last keypress was not received" messages:
This message may be due to interference with other 900MHz devices or because
the Aqua Pod is being used outside of the usable range. Follow step 14 above to
determine if there is an interference problem. If the Aqua Pod is too far from the
base station, consider locating the base station closer by using the Remote
Mount Kit.
Teach Wireless:
Successful
Press and hold
wireless button
Teach Wireless:
Successful