Goldline Aqua Pod Operation manual - Aqua Pod Operation
5
2.
Aqua Logic Programming Pushbuttons
These keys are used for programming and controlling the Aqua Logic. They operate
in the same manner as the Aqua Logic's local keypad buttons. Refer to the Aqua
Logic Installation and Operation manual for detailed information on the use of these
buttons.
3.
System Off
Pressing this button will turn all Aqua Logic outputs off, even if the unit is asleep.
They will remain off regardless of any programmed control logic until the System Off
button is pushed again (on this or any other remote control) or the “SERVICE” button
is pressed on the Aqua Logic's local display/keypad. If the Aqua Pod is asleep,
waking it by pressing this button will shut all of the Aqua Logic's outputs off.
NOTE:
System Off is not implemented for the Aqua Logic P-4 (AQL-P-4) and Aqua
Plus (AQL-PLUS) using software revision r2.60.
Aqua Pod Operation
The Aqua Pod will control and program the Aqua Logic in the same manner as the
local keypad/display except for the differences described below. Complete instruc-
tions on how to program and view/change settings are available in the Aqua Logic
Installation and Operation manuals. Use the Aqua Pod's programming buttons for
these commands.
Aqua Pod Backlight
Unlike the local keypad/display and other Aqua Logic remotes, the Aqua Pod's back-
light cannot be set to “Always on”. At any menu, the backlight operates in the
following manner:
• Press and hold “+” key for 1.5 seconds - backlight turns on for one minute
• Press any key while backlight is still on - one minute timer starts over
• Press and hold “–” key for 1.5 seconds - turns backlight back off
SoftKeys
The following two menus are available for the Aqua Pod but are not shown in the
Aqua Logic menus. These menus are directly accessible by repeatedly pushing the
Aqua Pod's MENU button. Refer to these menus and the information on page 6 to
map and operate softkeys.
Select Softkeys
Scrolls through available Softkey Sets
Press repeatedly until “Select Softkeys” menu is displayed
Select Softkey Set
Use the “” keys to scroll through all Softkey Sets. A
Softkey Set is a group of three pieces of pool equipment that
can be controlled by the three softkey pushbuttons. The
Softkey Sets are displayed in the Softkeys portion of the Aqua
Pod's display. Each softkey pushbutton controls the equip-
ment that is displayed directly above it. You can define and
make changes to Softkey Sets in the Softkey Set Mapping
menu.
Map Softkeys
locked
Press BOTH buttons SIMULTANEOUSLY for 5 seconds to unlock
Press repeatedly until “Map Softkeys locked” menu is displayed
Softkey Set Mapping
Push the “” for 5 seconds to unlock and enter the
Softkey Set Mapping menu. After entering this menu, one of
the displayed softkeys will be flashing. The flashing selection
can be changed by pressing the “+” or “-” keys. When the
desired selection is displayed, press the “” keys to
advance to the previous/next softkey. Create all desired softkey
sets using this procedure.
Refer to the diagram below for more information.
Softkey Set Mapping
After entering the Softkey Set Mapping menu, refer to the diagram below for mapping
information. After exiting the Softkey Set Mapping menu, the Aqua Pod will return to
normal operation.
6
1
2
3
Softkey Set 1:
Softkey Set 2:
Pool
(PS)
Cleaner
(V3)
Yard Light
(L)
Fountain
(A1)
Heat Pump
(H)
Gazebo Light
(A2)
To exit the Softkey Set Mapping
menu, press the corresponding
button to Save, Cancel or Reset.
Softkey currently being mapped blinks.
Press the “+” or “-” buttons to scroll
through the available selections to map
the Softkey.
Press the “”
buttons to move
to the previous/next Softkey set. Note
that the selection will blink while being
mapped.