I vistacam 1100 waterproof hd ip camera setup guide document version: 1.0 copyright 2015. All rights reserved. All trademarks and trade names are the properties of their respective owner.
Ii package contents the following items should be included: if any of these items are damaged or missing, please contact your service provider immediately. 1. Broad view camera * 1 2. Wall-mount stand * 1 3. Ethernet cable 8p8c (length 5m) * 1 4. Y-cable (rj45) * 1 5. Cable clip * 1 6. Rj45 rubber h...
Iii 8. Rp131 (wireless poe adapter) * 1.
1 chapter 1 introduction this chapter provides details of the waterproof hd ip camera's features, components and capabilities. Overview the vistacam 1100 waterproof hd ip camera has an integrated microcomputer and a mega pixel omnivision cmos sensor, enabling it to display high quality live streamin...
2 internet features • user-definable http/https port number. This allows internet gateways to use "port mapping" so the waterproof hd ip camera and a web server can share the same internet ip address. • ddns support. In order to view video over the internet, users must know the internet ip address o...
3 chapter 2 basic setup this chapter provides details on how to setup and mount the vistacam 1100 waterproof hd ip camera. System requirement to use the wired lan interface, a standard 10/100baset hub or switch and network cable is required. Physical details – vistacam 1100 waterproof hd ip camera f...
4 3. Pir sensor this is hardware sensor to detect motion. 4. Power/network /heater led on (green) - power on. Off (green) - no power. Blinking (green) - the led will be blinking every 3 seconds while booting. Fast blinking (green) - data is being transmitted or received via the lan port. On (blue) -...
5 1. Lan port the supplied ethernet cable can provide the power to the waterproof hd ip camera and also connect the device to your router. Note: • the wireless and lan interfaces cannot be used simultaneously. Recommended to use y-cable for rp131 configuration only. The lan cable should be always co...
6 setup the vistacam 1100 waterproof hd ip camera step 1 - rp131 configuration this configuration will set wireless connectivity of the camera via rp131. 1. Assemble the camera a. Hold the screw of the camera up. B. Attach the back of the camera to the stand and turn the camera clockwise to attach i...
7 • wps pbc mode. When pressed and released (less then 3 seconds), the rp131 will be in the wps pbc mode (auto link mode). • wps pin code mode. When pressed and held for over 3 seconds, the rp131 will be in the wps pin code mode. The wireless and lan interfaces cannot be used simultaneously. Using t...
8 mounting the waterproof hd ip camera note: please ensure camera is configured and added to the network before permanent mounting. 1. Identify the location for mounting the camera. 2. Install and drive two screws 2/3 of the way into the wall. 3. Remove the cover of the stand 4. Align the two mounti...
9 6. Attach the cover back to the stand. 7. Connect one end of the ethernet cable to the lan port of the camera and the other end to wireless poe adapter. 8. Screw/attach the camera onto the camera stand..
10 9. Make sure the waterproof hd ip camera is firmly fixed on the wall. Adjust the camera to the preferred position..
11 appendix a specifications vistacam 1100 waterproof hd ip camera model vistacam 1100 waterproof hd ip camera dimensions 83mm (h) * 83mm (w) * 45.5mm (d) operating temperature -20 ° c to 50 ° c storage temperature -40 ° c to 70 ° c network protocols tcp/ip, http, https, dhcp, smtp, ftp, upnp, ddns,...
12 this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This transmitter must...
