1. DL manuals
  2. Icom
  3. Transceiver
  4. IC-F3062S
  5. Sales handbook

Icom IC-F3062S Sales handbook

Manual is about: Icom Marine Radio User Manual

Summary of IC-F3062S

  • Page 1

    Ic ic - - f3062 series f3062 series sales handbook sales handbook count on us.

  • Page 2

    Foreword and disclaimer 2 the information in this document has been carefully checked, and is believed to be correct and accurate. However, icom assumes no responsibility for inaccuracies or mistakes. Furthermore, icom reserves the right to make changes to any of the products described in this handb...

  • Page 3

    Table of contents 1 introduction 1-1 company profile 4 2 over view 2-1product line up 5 2-2 common features· 6-7 2-3 key features of biis 1200 signalling 8 2-5 key features of 6.25khz digital 9 2-6 function and specifications comparison 10 2-7 supplied accessories attachments 11 2-8 optional accesso...

  • Page 4

    1 introduction 1-1 company profile 4 company profile company profile icom, the wireless communication experts icom inc. Is a company located in osaka, japan, and is a manufacturer of wireless communication products. Since icom’s establishment in 1954, we have had a long record as a trusted manufactu...

  • Page 5

    2 overview 2-1 product line up 5 vhf handheld transceivers uhf handheld transceivers s series (simple keypad version) t series (10-keypad version) supplied accessories (may differ according to version) dimensions.

  • Page 6

    2-2 common features lithium-ion battery pack the supplied 2000mah li-ion battery pack, bp-232, provides 14 hours* of operating time. Icom’s rugged dual-rail guide securely locks the battery to the radio. The optional battery case bp-240 provides a convenient back up and great reassurance in an emerg...

  • Page 7

    Common features a simple explanation of the ip rating system is written below. Please refer to more specialized information material if you wish to know more. An ip number contains two numbers (i.E. Ip65) in most instances which relate to the level of protection provided by an enclosure or housing. ...

  • Page 8

    2-3 key features of biis 1200 signalling what is biis 1200? Biis 1200 (binary interchange of information and signalling ) is a signalling protocol standardized by etsi (european telecommunications standards institute). The protocol allows users to send and receive short status messages as well as me...

  • Page 9

    2-5 key features of 6.25khz digital 6.25khz digital mode ready* with the optional ut-119h, the ic-f3062 series provides 6.25khz digital narrow mode communication, and increases efficiency of channel allocation and use of spectrum. The ic-f3062 series provides 2 optional slots: one optional slot for ...

  • Page 10

    2-6 function and specifications comparison 10

  • Page 11

    2-7 supplied accessory attachments 11 ¾ flexible antenna connect the supplied flexible antenna to the antenna connector. ¾ battery pack to attach the battery pack: slide the battery pack in the direction of the arrow ( ① ), then lock it with the battery release button. • slide the battery pack until...

  • Page 12

    2-8 optional accessories for handheld transceivers 12 ▲ bp-230n li-ion 7.4v/ 980mah ▲ bp-232n li-ion 7.4v/ 2000mah aaa(lr03) batteries×6 ▲ bp-240 bc-121n multi-charger + ad-106 charger adapter + bc-157 ac adapter rapidly charges up to 6 battery packs (six ad-106s are required). Charging time: approx...

  • Page 13

    Optional accessories for handheld transceivers 13 swivel type. Mb-86 and mb-93 swivel joints supplied belt clips leather belt hangers mb-93 : swivel type mb-94 : alligator type same as supplied. Mb-96n : swivel type. Mb-93 swivel joints supplied mb-96f : fixed type hs-94 : earhook headset with flexi...

  • Page 14

    Optional accessories for handheld transceivers 14 swivel type. Mb-93 swivel joints supplied cloning cable ut-110r voice scrambler unit : up to 1020 scrambling codes are available. Ut-124r man down unit : automatically sends an emergency signal when the transceiver is left in a horizontal ut-119h dig...

  • Page 15

    2-8-1 battery charging 15 using the optional battery chargers ¾ rapid charging with the bc-160 the optional bc-160 provides rapid charging of optional li-ion battery packs. • an ac adapter (may be supplied with bc-160 depending on version) or the dc power cable (opc- 515l/cp-17l) is additionally req...

  • Page 16

    Battery charging and battery case 16 important!: battery charging ensure the guide lobs on the battery pack are correctly aligned with the guide rails inside the charger adapter. (this illustration is described with the bc-160.) lobs guide rail optional battery case (bp-240) when using the optional ...

  • Page 17

    2-8-2 optional swivel belt clip 17 to attach a. Release the battery pack if it is attached. B. Slide the base clip in the direction of the arrow until the base clip is locked and makes a ‘click’ sound. Swivel belt clip mb-93 contents qty. A. Belt clip……………………………………………………… 1 b. Base clip ………………………………...

  • Page 18

    2-8-3 optional vs-1sc vox/ptt case 18 vs-1sc vox/ptt case the vs-1sc is a vox/ptt unit for icom handheld transceivers, and allows you hands-free operation. An optional headset (hs-94, etc.) is required for operation. • the vox (voice operated transmission) function starts transmission without pushin...

  • Page 19

    2-8-4 optional internal unit 19 optional unit installation ¾ general the ic-f3062 series transceiver can be installed with one of the following optional units. · ut-109r/ut-110r voice scrambler unit non- rolling type (ut-109r)/rolling type (ut-110r) voice scrambler unit provides higher communication...

  • Page 20

    3 operation and function 3-1 operation and function 20 rotary selector rotate to select the pre- programmed memory channels or the operating zone. (depending on the pre- setting) note: operation of the functions described below may depend on radio programming. Antenna connector connects the supplied...

  • Page 21

    3-1-1 function display 21 x signal strength indicator x indicates relative signal strength level. Y low power indicator appears when low output power is selected. Z audible indicator ➥ appears when the channel is in the ‘audible’ (unmute) condition. ➥ appears when the specified 2/5-tone/biis* code i...

  • Page 22

    3-1-2 functions programmable to keys 22 the following functions can be assigned to [emer], [side1], [side2], [side3], [p0], [p1], [p2] and [p3] programmable function keys. Consult your icom dealer or system operator for details concerning your transceivers programming. If the programmable function n...

  • Page 23

    Functions programmable to keys 23 high/low key “h/l” push to select the transmit output power temporarily or permanently, depending on the pre-setting. • ask your dealer for the output power level for each selection. C.Tone ch ent key “tsel” push to select the continuous tone channel using [ch up]/[...

  • Page 24

    Functions programmable to keys 24 user set mode key “set” ➥ push and hold to enter user set mode. • during user set mode, push this key to select an item, and change the value or condition using push [ch up]/[ch down]. ➥ push and hold this key again to exit user set mode. User set mode is also avail...

  • Page 25

    3-1-3 special functions 25 cpu revision indication the revision number of the cpu can be indicated on the lcd. It is convenient when confirming the cpu revision number if the cs-f3060 is not installed in the pc. ¾ operation while pushing and holding [p0] and [p3] keys, rotate [vol] to turn the power...

  • Page 26

    3-2 cloning software cs-f3060 3-2-1 basic setup of cloning software 26 getting started o this cloning software is designed to perform data setting and cloning for the ic-f3060/ic-f4060 series vhf/uhf portable transceivers. O help window: cs-f3060 has a help window to describe functions and operation...

  • Page 27

    Basic setup of cloning software 27 connections all cloning operations are performed from the computer’s keyboard— the operation required on the transceiver side is; 1. First, connect the cloning cable as illustrated below. 2. While pushing and holding [p0], rotate [vol] to turn power on. Screen desc...

  • Page 28

    Basic setup of cloning software 28 programming information • we recommend that you should read out all the transceiver’s data before start entering/editing parameters even if the transceiver is factory fresh. This avoids rare glitches which might cause programming errors when writing back the altere...

  • Page 29

    3-2-2 cloning items for conventional mode 29 the memory ch, msk, ltr™, digital, dtmf, continuous tone, scan, 2-tone, 5-tone and common items allow you to set the transceiver customized. Memory ch set the number of channels and the zone usage for each zone, and channel attribute, operating frequency,...

  • Page 30

    3-3 2-tone (lmr) signalling 30 ✔ lmr (2-tone) lmr (ltr) lmr (digital) pmr (5-tone/dtmf) biis pmr ✔ lmr (2-tone) lmr (ltr) lmr (digital) pmr (5-tone/dtmf) biis pmr what is 2-tone signalling? 1. Originally called “quick call”, this signalling protocol was developed by motorola in the 1950’s. 2. 2-tone...

  • Page 31

    3-4 5-tone (pmr) signalling 31 what is 5-tone signalling? 1. Although it is dubbed as 5-tone, this signalling protocol consists of a fast data burst of one (1) to seven (7) frequency tones that can selectively signal a radio. 2. Originally a european signalling protocol, 5-tone has numerous formats ...

  • Page 32

    5-tone (pmr) signalling 32 why chose 5-tone? • 5-tone is a non-proprietary signalling protocol that allows the icom radio to inter-operate with other brands using the 5-tone signalling. • this protocol also allows a mixed fleet operation. • it is faster than 2-tone by employing a quick data burst. •...

  • Page 33

    3-5 scan 33 . Only the checked channels in the same scan list are scanned when [scan a start/stop] or [scan b start/stop] key is pushed. [scan a start/stop] and [scan b start/stop] keys are assigned in key & display assign. For biis pmr: never include an msk channel into the scan list. The msk call ...

  • Page 34

    Scan 34 priority scan. "priority a" is selected channel in ch atr in memory ch screen is used for the priority channel. The scanning sequence is the same as mode 2 (prio-a) above. - the priority channel is selected automatically when scan is cancelled. - tx via [ptt] is performed in the priority cha...

  • Page 35

    Scan 35 mode 2 (prio-a,b): priority scan. The priority a and b channels are selected in ch atr in memory ch screen. The checked channels are scanned in sequence while monitoring the priority a and b channels. - the priority a channel is selected automatically when scan is cancelled during scanning. ...

  • Page 36

    Scan 36 ¾ text select the text indication capability from off, text or start ch during scan. Off : the text indication is turned off. Text : the text indication is turned on. The channel's text that is programmed in display text as above is indicated during scan. Start ch: the text indication is tur...

  • Page 37

    3-6 voice scrambling systems 37 ¾ difference between rolling and non-rolling types the rolling type (in fact, hopping type is used for the ut-110) is an additional feature which provides higher communication security. It changes the divided frequency over a specified period. Voice scrambling methods...

  • Page 38

    Voice scrambling systems 38 program setting for scrambler ¾ common - scrambler • type set installed voice scrambler type as ut-110r rolling or ut-109r non-rolling. As rolling type and non-rolling type have different code settings, they are not compatible. By selecting non-rolling type in this item, ...

  • Page 39: Count On Us!

    Count on us! Icom (uk) ltd. Sea street, herne bay, kent ct6 8ld telephone: +44 (0) 1227 741741. Fax: +44 (0) 1227 741742. Url: www.Icomuk.Co.Uk/ e-mail: info@icomuk.Co.Uk..