- DL manuals
- Icom
- Transceiver
- IC-F5062
- Instruction Manual
Icom IC-F5062 Instruction Manual
Summary of IC-F5062
Page 1
Instruction manual vhf mobile transceiver if5062 uhf mobile transceiver if6062.
Page 2
I explicit definitions rwarning! Never connect the transceiver to an ac outlet. This may pose a fire hazard or result in an electric shock. Never connect the transceiver to a power source of more than 16 v dc such as a 24 v battery. This connection will ruin the transceiver. Never cut the dc power c...
Page 3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ii avoid operating the transceiver without running the vehi- cle’s engine. The vehicle’s battery will quickly run out if the transceiver transmits while the vehicle’s engine off. Avoid placing the transceiver in excessively dusty envi- ronments. Avoid placing t...
Page 4: Panel Description
1 1 panel description i c o m i n c . Q e y speaker function display (p. 2) w r t ■ front panel q af volume control knob [vol] rotate the knob to adjust the audio output level. • minimum audio level is pre-programmed. W led indicator ➥ lights red while transmitting a signal. ➥ lights green while rec...
Page 5: ■ Function Display
2 1 panel description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ function display q signal strength indicator indicates relative signal strength level as below. W low power indicator appears when low output power is selected. E audible indicator ➥ appears when the channel is in the ‘audible’ (unmute) ...
Page 6
3 1 panel description ■ programmable function keys the following functions can be assigned to [up], [down], [p0], [p1], [p2], [p3] and [p4] programmable function keys. Consult your icom dealer or system operator for details con- cerning your transceivers programming. If the programmable function nam...
Page 7
4 1 panel description 1 prio a/b keys ➥ push to select priority a or priority b channel. ➥ push and hold [prio a (rewrite)] or [prio b (rewrite)] to set the operating channel as the priority a or priority b chan- nel. Mr-ch 1/2/3/4 keys push to select the memory channel 1 to 4 directly. Moni (audi) ...
Page 8
5 1 panel description high/low key push to select the transmit output power temporarily or per- manently, depending on the pre-setting. • ask your dealer for the output power level for each selection. C.Tone ch ent key push to select the continuous tone channel using [ch up]/[ch down] to change the ...
Page 9
6 1 panel description 1 tx code enter key (pmr or biis pmr operation only) push to enter the id code edit mode directly, for both 5-tone and msk. Then set the desired digit using [ch up]/ [ch down]. (p. 10) tx code channel select key ➥ push to enter the id code channel selection mode directly. Then ...
Page 10: Basic Operation
7 2 basic operation ■ turning power on q push [ ] to turn the power on. W if the transceiver is programmed for a start up password, input the digit codes as directed by your dealer. • the keys as below can be used for password input: the transceiver detects numbers in the same block as identical. Th...
Page 11: ■ Call Procedure
8 2 basic operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ call procedure when your system employs tone signaling (excluding ctcss and dtcs), the call procedure may be necessary prior to voice transmission. The tone signalling employed may be a selec- tive calling system which allows you to call s...
Page 12
9 2 basic operation d transmitting notes • transmit inhibit function the transceiver has several inhibit functions which restrict transmission under the following conditions: - the channel is in mute condition (‘inaudible’ condition; “ ” does not appear.) - the channel is busy. - un-matched (or matc...
Page 13
10 2 basic operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d tx code number edit (pmr or biis pmr operation only) if the transceiver has [tx code ch select] or [tx code enter] assigned to it, tx code contents can be edited within the allowable digits. Using [tx code ch select] key: q push [tx code ...
Page 14: ■ Scrambler Function
11 2 basic operation d dtmf transmission if the transceiver has [dtmf autodial] assigned to it, the auto- matic dtmf transmission function is available. Up to 8 dtmf channels are available. Q push [dtmf autodial]— a dtmf channel appears. W push [ch up] or [ch down] to select the desired dtmf channel...
Page 15: ■ User Set Mode
12 2 basic operation 2 ■ user set mode user set mode is accessed with [user set mode] and allows you to set seldom-changed settings. In this case you can “customize” the transceiver operation to suit your preferences and operating style. Entering the user set mode: q while pushing and holding [p1] a...
Page 16: Connection And Maintenance
13 3 connection and maintenance antenna black red 12v battery solder crimp note: use the terminals as shown below for the cable connections. R caution! Never remove t h e f u s e - h o l d e r f r o m t h e d c power cable. Q antenna connector connects to an antenna. Contact your dealer about antenn...
Page 17: ■ Supplied Accessories
14 3 connection and maintenance 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ supplied accessories ■ mounting the transceiver the universal mounting bracket supplied with your transceiv- er allows overhead mounting. • mount the transceiver securely with the 4 supplied screws to a thick surface which can ...
Page 18: ■ Antenna
15 3 connection and maintenance ■ antenna a key element in the performance of any communication sys- tem is an antenna. Contact your dealer about antennas and the best places to mount them. ■ fuse replacement a fuse is installed in each fuse holder of the supplied dc power cable. If a fuse blows or ...
Page 19: Doc
16 4 doc 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ce versions of the ic-f5062 and ic-f6062 which display the “ce” symbol on the serial number seal, comply with the essential require- ments of the european radio and telecommunication terminal directive 1999/5/ec. This warning symbol indicates that this...
Page 20: 0168
17 4 doc declaration of conformity we icom inc. Japan 1-1-32, kamiminami, hirano-ku osaka 547-0003, japan kind of equipment: uhf transceiver type-designation: ic- f6062 signature authorized representative name place and date of issue declare on our sole responsibility that this equipment complies wi...
Page 21
Memo 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16.
Page 22
Memo.
Page 23
Memo.
Page 24
1-1-32 kamiminami, hirano-ku, osaka 547-0003, japan ger aut gbr irl nor fra ned bel lux esp por ita gre swe den fin sui a-6566d-1eu-q printed in japan © 2007 icom inc. Printed on recycled paper with soy ink..