Instruction manual vhf mobile transceiver if5063 if5061/d uhf mobile transceiver if6063 if6061/d.
Read all instructions carefully and com- pletely before usng the transcever. Save this instruction manual — ths nstructon manual contans mportant operatng nstructons for the ic-f5061/d, ic-f5063 vhf mobile transceiv- ers, ic-f6061/d, ic-f6063 uhf mobile transceiv- ers . See the operatng gude for det...
R warning! Never connect the transcever to an ac outlet. Ths may pose a fire hazard or result n an electrc shock. R warning! Never connect the transcever to a power source of more than 16 v dc such as a 24 v battery. Ths connecton wll run the transcever. R warning! Never cut the dc power cable be- t...
Fcc information • for class b unintentional radiators: ths equpment has been tested and found to comply wth the lmts for a class b dgtal devce, pursuant to part 15 of the fcc rules. These lmts are desgned to provde reason- able protecton aganst harmful nterference n a resdental nstallaton. Ths equpm...
V table of contents important .......................................................................... Explicit definitions ....................................................... Precautions .................................................................... Voice coding technology ................
I c o m i n c . Q e y speaker function display (p. 2) w r t ■ front panel q af volume control knob [vol] rotate the knob to adjust the desred audo output level. • mnmum audo level s pre-programmed. W led indicator ➥ lghts red whle transmttng a sgnal. ➥ lghts green whle recevng a sgnal. E up/down key...
■ function display i c o m i n c . !1 q w e r t y u i o !0 q signal strength indicator indcates relatve sgnal strength level as below. Weak receive signal level strong w low power indicator appears when low output power s selected. E audible indicator ➥ appears when the channel s n the ‘audble’ (unm...
3 1 panel description ■ programmable function keys the followng functons can be assgned to [up] , [down] , [p0] , [p1] , [p2] , [p3] and [p4] programmable functon keys. Consult your icom dealer or system operator for detals con- cernng your transcevers programmng. If the programmable functon names a...
4 1 panel description 1 scan add/del (tag) key ➥ push to add or delete the selected channel to/from the scan group. 1. Push to ndcate the scan group, then push [ch up] or [ch down] to select the desred group. 2. Push to add or delete the channel to/from the selected scan group. 3. Push and hold for ...
5 1 panel description rx speaker key push to turn the rx speaker functon on or off. When the rx speaker functon s turned on, the receved audo can be heard va the external speaker. • ths functon s avalable when the external speaker s addtonally connected. • ths functon s useful when you are out of th...
6 1 panel description 1 wide/narrow key push to toggle the if bandwdth between wde and narrow. (analog or mxed mode operaton only) • the wde passband wdth can be selected from 25.0 or 20.0 khz usng the cs-f5060 cloning software . (pmr operaton only) ask your dealer for detals. Dtmf autodial key push...
7 1 panel description tx code channel up/down keys push to select a tx code channel drectly. Scrambler/encryption key ➥ whle n analog mode operaton, push to toggle the voce scrambler functon on and off. ➥ whle n dgtal mode operaton, push to toggle the encrypton transmsson functon on and off. Compand...
8 2 basic operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ turning power on q push and hold [ ] for 1 sec. To turn the power on. W if the transcever s programmed for a start up password, nput the dgt codes as drected by your dealer. • the keys as below can be used for password nput: the transcever...
9 2 basic operation ■ call procedure when your system employs tone sgnalng (excludng ctcss and dtcs), a call procedure may be necessary pror to voce transmsson. The tone sgnallng employed may be a selectve callng system whch allows you to call specfic staton(s) only and prevent unwanted statons from...
10 2 basic operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d transmitting notes • transmit inhibit function the transcever has several nhbt functons whch restrct transmsson under the followng condtons: - the channel s n mute condton (‘inaudble’ condton; “ ” (audble ndcator) does not appear.) - the ...
11 2 basic operation d tx code number edit (pmr operaton only) if the transcever has [tx code ch select] or [tx code enter] assgned to t, tx code contents can be edted wthn the allowable dgts. Using [tx code ch select] key: q push [tx code ch select] to enter the tx code channel selecton mode. • sel...
12 2 basic operation 2 ■ user set mode user set mode s accessed wth [user set mode] and allows you to set seldom-changed settngs. In ths case you can “customze” the transcever operaton to sut your prefer- ences and operatng style. Entering the user set mode: q whle pushng and holdng [p1] and [p2], p...
13 2 basic operation ■ scrambler function the voce scrambler functon provdes prvate communca- ton between statons. All versons have a bult-n frequency nverson type scrambler; however, an optonal rollng or non- rollng type s avalable as well. Q push [scrambler] to turn the scrambler functon on. • “ ”...
14 3 connection and maintenance 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 antenna black red 12v battery solder crimp note: use the terminals as shown below for the cable connections. R caution! Never remove t h e f u s e - h o l d e r f r o m t h e d c power cable. Q antenna connector connects to an an...
■ supplied accessories microphone* 1 microphone hanger and screw set microphone hanger cable dc power cable sponges* 3 mounting bracket flat washers spring washers bracket bolts mounting screws (m5 × 12) self-tapping screws (m5 × 16) nuts function name stickers* 2 * 3 * 2 the microphone type is diff...
16 3 connection and maintenance 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ antenna a key element n the performance of any communcaton systems s an antenna. Contact your dealer for more nfor- maton regardng antennas and how to nstall them. ■ fuse replacement a fuse s nstalled n the suppled dc power cab...
Your icom radio generates rf electromagnetic energy during transmit mode. This radio is de- signed for and classified as “occupational use only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is not...
Memo 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16.
1-1-32 kammnam, hrano-ku, osaka 547-0003, japan a-6565d-1ex- e prnted n japan © 2006–2008 icom inc. Prnted on recycled paper wth soy nk..