Instruction manual uhf transceiver if61-l p 0 p 1 p 2 p 3.
I foreword read all instructions carefully and completely before using the transceiver. Save this instruction manual— this instruction manual contains important operating instructions for the ic-f61-l uhf transceiver . This instruction manual includes some functions which are usable only when they a...
Ii recommendation clean the transceiver thoroughly with fresh water after exposure to saltwater, and dry it before operating. Otherwise, the transceiver’s keys, switches and controllers may be- come unusable, due to salt crystallization, and/or the charging ter- minals of the battery pack may rust. ...
Iii versions of the ic-f61-l which display the “ex” mark- ing on the serial number seal. The approval rating for these models are ii 2g ex ib iia t3 gb and ii 2d ex tb iiic t160°c db ip67. Warning! Never charge the bp-227axd (with/without the transceiver) in an explosive atmosphere. The optional bat...
Iv the atex standard is described on the sticker (ex marking) and bp-227axd as below. Bp-227axd • do not open when an explosive atmosphere may be present. • do not charge the battery in hazardous loca- tion. * the following illustrations show the ic-f61-l..
V precautions r danger! Never short terminals of the battery pack. Also, current may flow into nearby metal objects such as a key, so be careful when placing the battery packs (or the transceiver) in hand- bags, and so on. Simply carrying with or placing near metal objects such as a key, and so on m...
Vi do not push [ptt] when you do not actually intend to transmit. Do not operate or place the transceiver in direct sunlight or in areas with temperatures below –20°c or above +55°c. Do not modify the transceiver. The specifications may change and then not comply with the requirements of a correspon...
Vii table of contents foreword ........................................................................................ I operating notes............................................................................ I explicit definitions ..................................................................
Viii supplied accessories the following accessories are supplied: qty. • flexible antenna …………………………………………………… 1 • battery pack ……………………………………………………… 1 • jack cover ……………………………………………………… 1 set • belt clip ………………………………………………………… 1 set • function name stickers* (key-sticker) ……………………… 1 * there are no...
1 1 accessories ■ accessory attachments d flexible antenna connect the supplied flexible antenna to the antenna connector. Caution: • never carry the transceiver by holding the antenna. • do not connect the antenna other than listed on page 47. • transmitting without an antenna may damage the transc...
ï battery pack to attach the battery pack: slide the battery pack on the back of the transceiver in the direction of the arrow (q), then lock it with the battery release button. • slide the battery pack until the battery release button makes a ‘click’ sound. To remove the battery pack: push the batt...
3 2 panel description ■ front, top and side panels q w e r t y i u microphone function display (p. 6) speaker (see the following note.) note: if the speaker netting (for dust proofing) becomes wet, dry it with a hair drier (cool mode) etc. Before operating the transceiver. Otherwise the audio may be...
Q volume control [vol] turns power on and adjusts the audio level. W red button the desired function can be assigned by your dealer. E antenna connector connects the supplied antenna. R speaker-microphone connector [sp mic] connects the optional speaker-microphone. (p. 46) [sp mic] jack cover note: ...
■ front, top and side panels (continued) u transmit/busy indicator lights red while transmitting; lights green while receiving a sig- nal, or when the squelch is open. I ptt switch [ptt] push and hold to transmit; release to receive. 5 2 panel description.
■ function display r u y t e w q i q output power indicator appears when low 2 or low 1 is selected. W audible indicator ➥ appears when the channel is in the ‘audible’ (unmute) con- dition. ➥ appears when the specified 5-tone/biis code is received. E compander indicator appears when the compander fu...
■ programmable function keys the following functions can be assigned to [p0], [p1], [p2], [p3], [red], [ ] and [ ] programmable function keys. Consult your icom dealer or system operator for details concerning your transceivers programming. Ch up and down keys • select an operating channel. • select...
Priority channel keys ➥ push to select priority a or priority b channel. ➥ push and hold [prio a (rewrite)] to rewrite the prio a channel. Mr-ch 1/2/3/4 keys select an operating channel directly. Monitor key activates one of (or two of) the following functions on each chan- nel independently: • push...
■ programmable function keys (continued) c.Tone channel enter key select the continuous tone channel using [ch up]/[ch down] keys to change the tone frequency/code setting after pushing this key for permanent operation. Talk around key turn the talk around function on and off. • the talk around func...
Emergency keys ➥ push and hold to transmit an emergency call. ➥ when [emergency single (silent)] or [emergency repeat (si- lent)] is pushed, an emergency call is transmitted without a beep emission and lcd indication change. • if you want to cancel the emergency call, push (or push and hold) the key...
■ programmable function keys (continued) voice scrambler function push to toggle the voice scrambler function on and off. Compander key push to toggle the compander function on and off. The compander function reduces noise components from the trans- mitting audio to provide clear communication. User...
12 3 conventional operation 2 3 ■ turning power on q rotate [vol] to turn power on. W if the transceiver is programmed for a start up passcode, input digit codes as directed by your dealer. • the keys in the table below can be used for password input: • the transceiver detects numbers in the same bl...
■ call procedure when your system employs tone signalling (excluding ctcss and dtcs), the call procedure may be necessary prior to voice trans- mission. The tone signalling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from...
■ receiving and transmitting note: transmitting without an antenna may damage the trans- ceiver. See page 1 for antenna attachment. Receiving: q rotate [vol] to turn power on. W push [ ] or [ ] to select a channel. E when receiving a call, adjust the audio output level to a comfort- able listening l...
D transmitting notes • transmit inhibit function the transceiver has several inhibit functions which restrict trans- mission under the following conditions: - the channel is in mute condition (‘inaudible’ condition; “ ” does not appear). - channel is busy. - un-matched (or matched) ctcss is received...
D tx code number edit if the transceiver has [tx code ch select] or [tx code enter] as- signed to it, tx code contents can be edited within the allowable digits. To edit a tx code via [tx code ch select] key: q push [tx code ch select] to enter the tx code channel selec- tion mode. • select the desi...
D dtmf transmission if the transceiver has [dtmf autodial] assigned to it, the automatic dtmf transmission function is available. Up to 8 dtmf channels are available. To select a tx code: q push [dtmf autodial]— a dtmf channel appears. W push [ ]/[ ] to select the desired dtmf channel. E push [dtmf ...
■ user set mode if the transceiver has [user set mode] assigned to it, you can “cus- tomize” transceiver operation to suit your preferences and operat- ing style. Entering the user set mode: q push and hold [user set mode] for 1 sec. To enter the user set mode. W push [user set mode] momentarily to ...
19 4 biis operation ■ default setting the following functions are assigned to each programmable key as the default. Ask your dealer for details. [p0]; call : push to transmit a 5-tone/biis call when the selected channel is a 5-tone or msk channel, respectively. [p1]; digital : push to select the cal...
■ receiving a call d individual call q when an individual call is received; • beeps sound. • “ ” appears and the mute is released. • the programmed text message (e.G. “ ”) and the calling station id (or text) is displayed alternately, depending on the set- ting. • “ ” appears or blinks depending on ...
■ receiving a call (continued) d group call q when a group call is received; • beeps sound. • “ ” appears and the mute is released. • the programmed text message (e.G. “ ”) and the calling sta- tion id (or text) is displayed alternately, depending on the setting. • “ ” appears or blinks depending on...
D displaying the received call record — queue indication the transceiver memorizes the calling station ids for record. Up to 3 calls can be memorized, and the oldest call record is erased when a 4th call is received. However, once the transceiver is pow- ered off, the all records are cleared. Q push...
■ transmitting a call total of a 3 ways for code selection are available—selecting the call code from memory, entering the call code from the keypad and calling back from the queue channel record. D using call memory q while in the standby condition, push [p1] (digital) to enter the call code memory...
D calling back from the queue channel q while in the standby condition, push [p1] (digital) for 1 sec. To enter queue memory channel selection mode. W push [ ]/[ ] to select the desired record. E push [p0] (call) or [ptt]* to call. *ptt call can be made only when ptt call capability is permitted. No...
■ transmitting a call (continued) d direct code entry q while in the standby condition, push [tx code enter] to enter the tx code edit mode. • editable code digit blinks. W push [tx code enter] to select the desired digit to be edited. • editable digit differs according to the setting. E set the des...
■ receiving a message d receiving a status message q when a status message is received; • beeps sound. • the calling station id (or text) and the status message is displayed alternately, depending on the setting. W push [p3] (moni(audi)) to return to the standby condition. Note: only the calling sta...
■ receiving a message (continued) d receiving an sdm q when an sdm is received; • beeps sound. • the calling station id (or text) and the sdm is displayed alter- nately, depending on the setting. W when the received sdm includes more than 8 characters, the message scrolls automatically, when the aut...
D received message selection the transceiver memorizes the received messages for record. Up to 6 messages for status and sdm, or 95 character sdm’s can be memorized. The oldest message is erased when the 7th mes- sage is received. However, once the transceiver is powered off, all messages are cleare...
■ transmitting a status d general the status message can be selected with the programmed text, and the message text is also displayed on the function display of the called station. Up to 24 status types (1 to 24) are available, and the status mes- sages 22 and 24 have designated meanings. Status 22:...
■ transmitting an sdm d general the short data message, sdm, can be sent to an individual station or group stations. Also, 8 sdm memory channels are available and the messages can be edited via pc programming. D transmitting an sdm q while in the standby condition, push [p1] (digital), then push [ ]...
■ position data transmission when the optional opc-966 interface cable and a gps receiver is connected to the transceiver, the position (longitude and latitude) data can be transmitted automatically. Ask your dealer or system operator for connection details. The position data is transmitted when; • ...
■ printer connection when the optional opc-966 interface cable is connected to the transceiver, a printer can be connected to print out the received sdm content and the id of the station who sent the message. Ask your dealer or system operator for connection details. ■ pc connection when the optiona...
■ auto emergency transmission when [emergency single (silent)] or [emergency repeat (silent)] is pushed, an emergency signal is automatically transmitted for the specified time period. The status 22 (emergency) is sent to the selected id station, and the position data is transmitted after the emerge...
■ biis indication the following indications are available for the biis operation on an msk channel. : individual/group call is successful. : message (status or sdm) transmission is successful. : no answer back is received. : appears during retry of the call (2nd call). : end the communication. : ope...
35 5 battery charging ■ caution • misuse of lithium-ion batteries may result in the following haz- ards: smoke, fire, or the battery may rupture. Misuse can also cause damage to the battery or degradation of battery perfor- mance. • prior to using the battery pack for the first time, or after not us...
36 5 battery charging 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 r danger! Do not expose the battery to rain, snow, seawa- ter, or any other liquids. Do not charge or use a wet battery. If the battery gets wet, be sure to wipe it dry before using. The battery is not waterproof. R danger! Kee...
37 5 battery charging ■ caution dbattery caution (continued) caution: always use the battery within the specified temperature range for the transceiver (–20˚c to +55˚c) and the battery itself (–10˚c to +60˚c). Using the battery out of its specified temperature range will reduce the battery’s perform...
38 5 battery charging 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 d charging caution r danger! Never charge the battery pack in areas with ex- tremely high temperatures, such as near fires or stoves, inside a sun heated car, or in direct sunlight. In such environments, the safety/protection c...
■ optional battery chargers ï regular charging with the bc-152n q attach the bc-152n to a flat surface, such as a desk, if de- sired. W connect the power adapter as shown below. E insert the battery pack with/without the transceiver into the char- ger. • the charge indicator lights green. R charge t...
❍ charging indicator: • lights orange while charging. • lights green when charging is completed. • blinks orange or green, or does not light when a problems is de- tected. Solutions: • remove the battery pack, and reinsert it. • remove the battery pack, clean the battery terminals, then reinsert it....
■ optional battery chargers (continued) ï ad-100 installation the ad-100 charger adapter must be installed into the bc-119n or bc-121n before battery charging. Q connect the ad-100 charger adapter and the bc-119n or bc- 121n. W install the ad-100 into the holder space of the bc-119n or bc- 121n with...
D rapid charging with the bc-119n+ad-100 the optional bc-119n provides rapid charging of li-ion battery pack. The following are additionally required: • one ad-100 (purchase separately) • a power adapter (may be supplied with bc-119n depending on version) or the dc power cable (opc-515l/cp-23l). Pow...
■ optional battery chargers (continued) d rapid charging with the bc-121n+ad-100 the optional bc-121n allows up to 6 battery packs to be charged simultaneously. The following are additionally required. • six ad-100 (purchase separately) • a power adapter (bc-157) or the dc power cable (opc-656) powe...
44 5 battery charging 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 important: battery charging caution ensure the guide tabs on the battery pack are correctly aligned with the guide rails inside the charger adapter. (this illustration shows the bc-152n.) tabs guide rails.
45 6 speaker-microphone ■ optional hm-138 description alligator type clip to attach the speaker-mic. To your shirt or collar, etc. Ptt switch transmits while pushed receives while released microphone speaker never immerse the connector in water. If the connector becomes wet, be sure to dry it before...
46 6 speaker-microphone 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ■ attachment attach the connector of the speaker-microphone into the [sp mic] connector on the transceiver and tighten the screw. Detaching: unscrew (q), then detach the jack cover (w). Attaching: attach the jack cover (e), t...
47 7 options • bp-227axd l i - ion battery pack 7.4 v/1850 mah/14 wh li-ion battery pack. The same as supplied with the transceiver. Bp-227axd must be charged with the op- tional bc-152n, bc-119n or bc-121n. • bc-152n desktop charger + bc-147s ac adapter used for regular charging of the battery pack...
48 7 options 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 approved icom optional equipment is designed for optimal perfor- mance when used with an icom transceiver. Icom is not responsible for the destruction or damage to an icom transceiver in the event it is used with equipment that is not m...
49 8 atex cautions d special conditions for safe use the equipment is an intrinsically safe equipment. It can be used in a potentially explosive atmosphere. The equipment must be powered only by the battery icom type bp-227axd. When the transceiver is used in a hazardous areas, either the jack cover...
50 8 atex cautions 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 d meaning of atex marking codes equipment conforms to types of protection standardized by cenelec (european standards) intrinsic safety according en60079-0 and en60079-11 marking temperatures (see fig. 1) ip code dust group max su...
51 8 atex cautions —— — — — — — — — — — — — — — — — — — — — —— — — max. T emperature gas group t1: 450 °c t2: 300 °c t3: 200 °c t4: 135 °c t5: 100 °c t6: 85 °c methane —— — — — —— — — — —— — — — —— — — — —— — — — ethyl alcohol i-amyl acetate n-butane n-butyl alcohol ethylene acetylene acetalde hyde ...
The following explanations are about the symbols on the attached declaration of conformity. Ce versions of the ic-f61-l which display the “ce” symbol on the serial number label, comply with the es- sential requirements of the atex directive. 52 9 ce 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Memo.
Memo.
1-1-32 kamiminami, hirano-ku, osaka 547-0003, japan a-6938h-1ex-r printed in japan © 2011–2016 icom inc. Printed on recycled paper with soy ink..