Instruction manual uhf transceiver if61 vhf transceiver if51 p 0 p 1 p 2 p 3 this illustration shows the ic-f51..
I important read all instructions carefully and completely before using the transceiver. Save this instruction manual— this instruction manual contains important operating instructions for the ic-f51 vhf transceiver and ic-f61 uhf transceiver . This instruction manual includes some functions which a...
Ii recommendation clean the transceiver thoroughly in a bowl of fresh water after exposure to saltwater, and dry it before op- erating. Otherwise, the transceiver’s keys, switches and controllers may become unusable, due to salt crystallization, and/or the charg- ing terminals of the battery pack ma...
Iii versions of the ic-f51/f61 which display the “ex” marking on the serial number seal. The approval rating for these models are ii 2g ex ib ii a t3 gb and ii 2d ex tb iii c t160°c db ip67. Warning! Never charge the bp-227axd (with/without the transceiver) in an explosive atmosphere. The optional b...
Iv the atex standard is described on the sticker (ex marking) and bp-227axd as below. Bp-227axd • do not open when an explosive atmosphere may be present. • do not charge the battery in hazardous loca- tion. * the following illustrations show the ic-f51/f61..
V precautions r danger! Never short the terminals of the battery pack. Short- ing may occur if the terminals touch metal objects such as a key, so be careful when placing the battery packs (or the transceiver) in bags, and so on. Carry them so that shorting cannot occur with metal objects. Shorting ...
Vi caution: do not place or leave the transceiver in direct sun- light or in places with temperatures below –20°c or above +55°c. Caution: do not modify the transceiver. The specifications may change and then the transceiver may not comply with the require- ments of required regulations. The transce...
Vii table of contents important ......................................................................................... I operating notes............................................................................ I explicit definitions ................................................................
Viii table of contents supplied accessories the following accessories are supplied: qty. • flexible antenna …………………………………………………… 1 • battery pack ……………………………………………………… 1 • jack cover ……………………………………………………… 1 set • belt clip ………………………………………………………… 1 set • function name stickers* (key-sticker) ……………………...
1 1 accessories ■ accessory attachments d flexible antenna connect the supplied flexible antenna to the antenna connector. Caution: • never carry the transceiver by holding the antenna. • do not connect the antenna other than listed on page 47. • transmitting without an antenna may damage the transc...
2 1 accessories 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ï battery pack to attach the battery pack: slide the battery pack on the back of the transceiver in the direc- tion of the arrow ( q ), then lock it with the battery release button. • slide the battery pack until the battery release ...
3 2 panel description ■ front, top and side panels q w e r t y i u microphone function display (p. 6) speaker (see the following note.) note: if the speaker netting (for dust proofing) becomes wet, dry it with a hair drier (cool mode) etc. Before operating the transceiver. Otherwise the audio may be...
Q volume control [vol] turns on the transceiver and adjusts the audio level. W red button a desired function can be assigned by your dealer. E antenna connector connects to the supplied antenna. R speaker-microphone connector [sp mic] connects to the optional speaker-microphone. (p. 46) [sp mic] jac...
■ front, top and side panels (continued) u transmit/busy indicator lights red while transmitting, lights green while receiving a sig- nal, or when the squelch is open. I ptt switch [ptt] hold down to transmit, release to receive. 5 2 panel description.
■ function display r u y t e w q i q output power indicator displayed when low 2 or low 1 is selected. W audible indicator ➥ displayed when the channel is in the ‘audible’ (unmute) mode. ➥ displayed when the specified 5-tone/biis code is received. E compander indicator displayed when the compander f...
■ programmable function keys the following functions can be assigned to [p0] , [p1] , [p2] , [p3] , [red] , [ ] and [ ] programmable function keys. Consult your icom dealer or system operator for details concerning your transceivers presetting. Ch up and down keys • select an operating channel. • se...
Priority channel keys ➥ push to select priority a or priority b channels. ➥ hold down [prio a (rewrite)] or [prio b (rewrite)] for 1 second to rewrite the priority a or b channel. Mr-ch 1/2/3/4 keys directly select an operating channel. Monitor key independently a one or two of the following functio...
C.Tone channel enter key select the continuous tone channel using [ch up]/[ch down] keys to change the tone frequency/code setting after pushing this key. Talk around key push to turn the talk around function on or off. • the talk around function equalizes the transmit frequency to the re- ceive fre...
Emergency keys ➥ hold down for preset period of time to transmit an emergency call. ➥ when [emergency single (silent)] or [emergency repeat (si- lent)] is pushed, an emergency call is transmitted without a beep sound or lcd indication change. • if you want to cancel the emergency call, push (or hold...
Voice scrambler function push to toggle the voice scrambler function on or off. Compander key push to toggle the compander function on or off. The compander function reduces noise components from the trans- mitting audio to provide clear communication. User set mode key ➥ hold down for 1 second to e...
12 3 conventional operation 2 3 ■ turning power on q rotate [vol] to turn power on. W if the transceiver is programmed for a start up passcode, input digit codes as directed by your dealer. • the keys in the table below can be used for password input: • the transceiver detects numbers in the same bl...
■ call procedure when your system employs tone signalling (excluding ctcss and dtcs), the call procedure may be necessary prior to voice trans- mission. The tone signalling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from...
■ receiving and transmitting note: transmitting without an antenna may damage the trans- ceiver. See page 1 for antenna attachment. Receiving: q rotate [vol] to turn power on. W push [ ] or [ ] to select a channel. E when receiving a call, adjust the audio output level to a comfort- able listening l...
D transmitting notes • transmit inhibit function the transceiver has several inhibit functions which restrict trans- mission under the following conditions: - the channel is in mute condition (‘inaudible’ condition: “ ” does not appear). - channel is busy. - un-matched (or matched) ctcss is received...
D tx code number edit if the transceiver has [tx code ch select] or [tx code enter] as- signed to it, tx code contents can be edited within the allowable digits. To edit a tx code via [tx code ch select] key: q push [tx code ch select] to enter the tx code channel selec- tion mode. • select the desi...
D dtmf transmission if the transceiver has [dtmf autodial] assigned to it, the automatic dtmf transmission function is available. Up to 8 dtmf channels are available. To select a tx code: q push [dtmf autodial]— a dtmf channel appears. W push [ ]/[ ] to select the desired dtmf channel. E push [dtmf ...
■ user set mode if the transceiver has [user set mode] assigned to it, you can “cus- tomize” the transceiver operation to suit your preferences and op- erating style. Entering the user set mode: q hold down [user set mode] for 1 second to enter the user set mode. W push [user set mode] momentarily t...
19 4 biis operation ■ default setting the following functions are assigned to each programmable key as the default. Ask your dealer for details. [p0]: call : push to transmit a 5-tone/biis call when the selected channel is a 5-tone or msk chan- nel, respectively. [p1]: digital : push to select the c...
■ receiving a call d individual call q when an individual call is received: • beeps sound. • “ ” is displayed and the mute is released. • the entered text message (example: “ ”) and the calling station id (or text) is alternately displayed, depending on the pre- setting. • “ ” is displayed or blinks...
D group call q when a group call is received: • beeps sound. • “ ” is displayed and the mute is released. • the entered text message (example: “ ”) and the calling sta- tion id (or text) is alternately displayed, depending on the preset- ting. • “ ” is displayed or blinks, depending on the presettin...
D displaying the received call record — queue indication the transceiver memorizes the calling station ids for a call re- cord. Up to 3 calls can be memorized, and the oldest call record is erased when the 4th call is received. However, once the trans- ceiver is powered off, the all records are clea...
■ transmitting a call there are 3 ways to select a code—selecting the call code from memory, entering the call code from the keypad and calling back from the queue channel record. D using call memory q while in the standby condition, push [p1] (digital) to enter the call code memory channel selectio...
D calling back from the queue channel q while in the standby condition, hold down [p1] (digital) for 1 second to enter queue memory channel selection mode. W push [ ]/[ ] to select the desired record. E push [p0] (call) or [ptt]* to call. *ptt call can be made only when ptt call capability is permit...
D direct code entry q while in the standby condition, push [tx code enter] to enter the tx code edit mode. • editable code digit blinks. W push [tx code enter] to select the desired digit to be edited. • editable digit differs according to the setting. E set the desired digit using [ ]/[ ]/[tx code ...
■ receiving a message d receiving a status message q when a status message is received; • beeps sound. • the calling station id (or text) and the status message is displayed alternately, depending on the setting. W push [p3] (moni(audi)) to return to the standby condition. Note: only the calling sta...
D receiving an sdm q when an sdm is received; • beeps sound. • the calling station id (or text) and the sdm is displayed alter- nately, depending on the setting. W when the received sdm includes more than 8 characters, the message scrolls automatically, when the automatic scroll func- tion is activa...
D received message selection the transceiver memorizes the received messages for record. Up to 6 messages for status and sdm, or 95 character sdm’s can be memorized. The oldest message is erased when the 7th mes- sage is received. However, once the transceiver is powered off, all messages are cleare...
■ transmitting a status d general the status message can be selected with the programmed text, and the message text is also displayed on the function display of the called station. Up to 24 status types (1 to 24) are available, and the status mes- sages 22 and 24 have designated meanings. Status 22:...
■ transmitting an sdm d general the short data message, sdm, can be sent to an individual station or group stations. Also, 8 sdm memory channels are available and the messages can be edited via pc programming. D transmitting an sdm q while in the standby condition, push [p1] (digital), then push [ ]...
■ position data transmission when the optional opc-966 interface cable and a gps receiver is connected to the transceiver, the position (longitude and latitude) data can be transmitted automatically. Ask your dealer or system operator for connection details. The position data is transmitted when ; •...
■ printer connection when the optional opc-966 interface cable is connected to the transceiver, a printer can be connected to print out the received sdm content and the id of the station who sent the message. Ask your dealer or system operator for connection details. ■ pc connection when the optiona...
■ auto emergency transmission when [emergency single (silent)] or [emergency repeat (silent)] is pushed, an emergency signal is automatically transmitted for the specified time period. The status 22 (emergency) is sent to the selected id station, and the position data is transmitted after the emerge...
■ biis indication the following indicators are displayed for biis operation on an msk channel. : individual/group call is successful. : message (status or sdm) transmission is successful. : no answer back is received. : appears during retry of the call (2nd call). : end the communication. : operatin...
35 5 battery charging ■ caution misuse of lithium-ion batteries may result in the following hazards: smoke, fire, or the battery may rupture. Misuse can also cause damage to the battery or degradation of battery performance. R warning! Never charge the battery (with/without the transceiver) in an ex...
36 5 battery charging 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 r danger! Never expose the battery pack to rain, snow, sea- water, or any other liquids. Do not charge or use a wet battery pack. If the pack gets wet, be sure to wipe it dry before using. The battery pack itself is not waterpr...
37 5 battery charging ■ caution d battery caution (continued) caution: do not use the battery pack out of the specified tem- perature range for the transceiver (–20˚c to +55˚c) and the pack itself (–10˚c to +60˚c). Using the pack out of its specified tem- perature range will reduce it’s performance ...
38 5 battery charging 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 d charging caution r danger! Never charge the battery pack in areas with ex- tremely high temperatures, such as near fires or stoves, inside a sunheated vehicle, or in direct sunlight. In such environments, the safety/protectio...
39 5 battery charging ■ optional battery chargers ï regular charging with the bc-152n q attach the bc-152n to a flat surface, such as a desk, if de- sired. W connect the power adapter as shown below. E insert the battery pack with/without the transceiver into the char- ger. • the charge indicator li...
40 5 battery charging 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ❍ charging indicator: • lights orange while charging. • lights green after charging is completed. • blinks orange or green, or does not light when a problems is de- tected. Solutions: • remove the battery pack, and reinsert it....
41 5 battery charging ■ optional battery chargers (continued) ï ad-100 installation the ad-100 charger adapter must be installed into the bc-119n or bc-121n before battery charging. Q connect the ad-100 charger adapter and the bc-119n or bc- 121n. W install the ad-100 into the holder space of the bc...
42 5 battery charging 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 power adapter (not supplied with some versions.) ad-100 charger adapter is installed in bc-119n. Battery pack transceiver optional opc-515l* (for 13.8 v power source) or cp-23l (for 12 v cigarette lighter socket) can be used in...
43 5 battery charging ■ optional battery chargers (continued) d rapid charging with the bc-121n+ad-100 the optional bc-121n allows up to 6 battery packs to be charged simultaneously. The following are additionally required. • six ad-100 (purchase separately) • a power adapter (bc-157) or the dc powe...
44 5 battery charging 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 important: battery charging caution ensure the guide tabs on the battery pack are correctly aligned with the guide rails inside the charger adapter. (this illustration shows the bc-152n.) tabs guide rails.
45 6 speaker-microphone ■ optional hm-138 description alligator type clip to attach the speaker-mic. To your shirt or collar, etc. Ptt switch transmits while pushed receives while released microphone speaker never immerse the connector in water. If the connector becomes wet, be sure to dry it before...
46 6 speaker-microphone 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ■ attachment attach the connector of the speaker-microphone into the [sp mic] connector on the transceiver and tighten the screw. Detaching: unscrew ( q ), then detach the jack cover ( w ). Attaching: attach the jack cover ( ...
47 7 options • bp-227axd l i - i on battery pack 7.4 v/1850 mah/14 wh li-ion battery pack. The same as supplied with the transceiver. Bp-227axd must be charged with the op- tional bc-152n or the bc-119n/121n. • bc-152n desktop charger + bc-147s ac adapter used for regular charging of the battery pac...
48 7 options 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 some options may not be available in some countries. Please ask your dealer for details..
49 8 atex cautions d special conditions for safe use the equipment is an intrinsically safe equipment. It can be used in a potentially explosive atmosphere. The equipment must be powered only by the battery icom type bp-227axd. When the transceiver is used in a hazardous areas, either the jack cover...
50 8 atex cautions 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 d meaning of atex marking codes equipment conforms to types of protection standardized by cenelec (european standards) intrinsic safety according en60079-0 and en60079-11 marking temperatures (see fig. 1) ip code dust group max su...
51 8 atex cautions —— — — — — — — — — — — — — — — — — — — — —— — — max. T emperature gas group t1: 450 ° c t2: 300 ° c t3: 200 ° c t4: 135 ° c t5: 100 ° c t6: 85 ° c methane —— — — — —— — — — —— — — — —— — — — —— — — — ethyl alcohol i-amyl acetate n-butane n-butyl alcohol ethylene acetylene acetalde...
Hereby, icom inc. Declares that the versions of ic- f51/ic-f61 which have the “ce” symbol on the product, comply with the essential requirements of the radio equipment directive, 2014/53/eu, and the restriction of the use of certain hazardous sub- stances in electrical and electronic equipment di- r...
53 10 information ■ country code list (iso 3166-1) country codes country codes 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 austria belgium bulgaria croatia czech republic cyprus denmark estonia finland france germany greece hungary iceland ireland italy latvia at be bg hr cz cy dk ee fi fr de gr hu is...
Memo 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
1-1-32 kamiminami, hirano-ku, osaka 547-0003, japan a6365h-1eu-19 printed in japan © 2005–2017 icom inc. Printed on recycled paper with soy ink. At fi it pl gb ro be fr lv pt is tr cy de lt sk li hr cz gr lu si no dk hu mt es ch ee ie nl se bg.