1. DL manuals
  2. Icom
  3. Two-Way Radio
  4. IP100H
  5. Quick Manual

Icom IP100H Quick Manual

Manual is about: IP Advanced Radio System

Summary of IP100H

  • Page 1

    ©2014 icom america inc. Page 1 icom america, inc. 12421 willows road ne kirkland, wa 98034 quick guide for ip advanced radio system over an existing wireless lan this application describes all the programming required to configure a working ip advanced radio system that is being connected to an exis...

  • Page 2: What You Will Need

    ©2014 icom america inc. Page 2 icom america, inc. 12421 willows road ne kirkland, wa 98034 what you will need • 1 ip1000c controller box • several ip100h radios • access point(s) – either customer’s existing points or supplied by your icom dealer (linksys access point used in this guide) • cs-ip100h...

  • Page 3

    ©2014 icom america inc. Page 3 icom america, inc. 12421 willows road ne kirkland, wa 98034 • a new network ssid needs to be created that will refer to all devices on the ip radio system. This ssid is designated to icom ip radio system only. We are using “cisco80915” as the ssid in our example. • ssi...

  • Page 4

    ©2014 icom america inc. Page 4 icom america, inc. 12421 willows road ne kirkland, wa 98034 5. After the reset is done, go to network settings and click the ip address tab. 6. Change the ip address for the ip1000c to match the company’s network ip scheme. This will be determined by the company’s it m...

  • Page 5

    ©2014 icom america inc. Page 5 icom america, inc. 12421 willows road ne kirkland, wa 98034 creating unit ids in the ip1000c web interface entering ip100h radio information the following example shows programming for three ip100h radios. 1. Click on the transceiver settings tab and transceiver regist...

  • Page 6

    ©2014 icom america inc. Page 6 icom america, inc. 12421 willows road ne kirkland, wa 98034 1. Enter the transceiver 2 radio information as follows and click apply..

  • Page 7

    ©2014 icom america inc. Page 7 icom america, inc. 12421 willows road ne kirkland, wa 98034 2. Enter transceiver 3 radio informationas follows and click apply. 3. Confirm that the transceivers appear under the transceiver setting entry list set up all other transceivers in the same way. After adding ...

  • Page 8

    ©2014 icom america inc. Page 8 icom america, inc. 12421 willows road ne kirkland, wa 98034 4. Select wpa-psk/wpa2-psk in the authentication field. 5. Enter the wireless lan password in the psk field. In this example, we are using “1234567890” as shown above in customer’s ip parameters settings. 6. V...

  • Page 9

    ©2014 icom america inc. Page 9 icom america, inc. 12421 willows road ne kirkland, wa 98034 note: this password talks to the controller not the wlan system. 10. Programming radio no. 2: enter “2” in trx no. Box for transceiver no. 2. 11. Enter password (iptrx) same as setup in the ip1000c for unit id...

  • Page 10

    ©2014 icom america inc. Page 10 icom america, inc. 12421 willows road ne kirkland, wa 98034 2. Create group 1 with 2 ip radios (as an example) as follows. In our example, group 1 will only have unit id 0001 and 0002 part of its group. When making a group call – anther unit id, such as 0003, wouldn’t...

  • Page 11

    ©2014 icom america inc. Page 11 icom america, inc. 12421 willows road ne kirkland, wa 98034 2. Enter group 1 in the name (no.:) field. 3. Ensure call type is set to group. 4. Enter 0001 as destination id and click apply tab. 5. Enter roger (example) for name below no.: 2. 6. Select individual as the...

  • Page 12

    ©2014 icom america inc. Page 12 icom america, inc. 12421 willows road ne kirkland, wa 98034 9. Click common settings under common setting tab and click edit. 10. Select 1 in id list box. 11. Click apply. 12. Verify that id list number now shows “1”. 13. Click the transceiver settings tab and then tr...

  • Page 13

    ©2014 icom america inc. Page 13 icom america, inc. 12421 willows road ne kirkland, wa 98034 in the following steps, each individual radio id will be enabled to accept (use) that id list. 14. Choose unit id in the unit field. 15. Click to enable the use id list setting and click the apply tab at the ...

  • Page 14

    ©2014 icom america inc. Page 14 icom america, inc. 12421 willows road ne kirkland, wa 98034 important: each ip100h radios must be rebooted after adding/deleting or changing any setting in the ip1000c controller. Making a group/individual call from your ip100h radio.