When performance matters. ™ 4273092-nl-reva safety, operation and maintenance manual veiligheids-, bedienings- en onderhoudshandleiding ar522™ 68131 – ar522-t4i, kubota® v2403-m-di, 4wd with rops 68131 – ar522-t4i, kubota® v2403-m-di, 4wd met rops warning warning: if incorrectly used this machine ca...
2 this manual contains safety and operating instructions for your new jacobsen machine. This manual should be stored with the equipment for reference during operation. Before you operate your machine, you and each operator you employ should read the manual carefully in its entirety. By following the...
Contents 3 contents contents safety 1.1how to operate safely . . . . . . . . . . . . . . . . . . . . 4 1.2 important safety notes . . . . . . . . . . . . . . . . . 7 specifications 2.1 product identification . . . . . . . . . . . . . . . . . . 8 2.2 v2403-m-di engine . . . . . . . . . . . . . . . . ...
1 safety 4 1 safety 1.1 how to operate safely safe operation a read the operator’s manual and other training material. If the operator or technician can not read this manual, the owner is responsible to describe this material to the operators and technicians. Manuals in additional languages may be a...
Safety 1 5 d keep your legs, arms and body inside the operator compartment while the mower is in operation. Keep your hands and feet away from the cutting units. E do not use on the slopes greater than the safe slope limit for the equipment. F to guard against over turning or loss of control: – oper...
1 safety 6 e refuel the mower before you start the engine. When the engine is in operation or while the engine is hot, never remove the fuel cap or add fuel to the mower. F refuel outdoors only and do not smoke when you add fuel. Extinguish all types of ignition. G the fuel nozzle must touch the rim...
Safety 1 7 1.2 important safety notes ________________________________________________ this safety alert symbol is used to alert you to potential hazards. Danger - indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Warning - indicates a potenti...
2 specifications 8 2 specifications 2.1 product identification _________________________________________________ 68131 .............................. Ar522-t4i, 5 gang 4wd with rops an identification plate, like the one shown, listing the serial number, is attached to the frame of the mower and is l...
Specifications 2 9 2.5 cutting units ___________________________________________________________ overall cutting width ....... 90 in. (254 cm) number of cutting units: .. Five - three front, two rear. Height of cut................... .3/4 to 5-1/4 in. (1.9 to 13.3 cm) in 1/4 in. (0.6 cm) increments ...
2 specifications 10 2.8 declaration of conformity ____________________________________________ declaration of conformity ▪ ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ ▪ prohlÁŠenÍ o shodĚ ▪ overensstemmelseserklÆring ▪ conformiteitsverklaring ▪ vastavusdeklaratsioon ▪ vaatimustenmukaisuusvakuutus ▪ declaration de co...
Specifications 2 11 uk notified body for 2000/14/ec ▪ Нотифициран орган в Обединеното кралство за 2000/14/ЕО ▪ Úřad certifikovaný podle směrnice č. 2000/14/ec ▪ det britiske bemyndigede organ for 2001/14/ef ▪ engels adviesorgaan voor 2000/14/eg ▪ Ühendkuningriigi teavitatud asutus direktiivi 2000/14...
2 specifications 12 signature of the person empowered to draw up the declaration on behalf of the manufacturer, holds the technical documentation and is authorised to compile the technical file, and who is established in the community. Подпис на човека, упълномощен да състави декларацията от името н...
Specifications 2 13 2.9 vibration level_________________________________________________________ when the machine was tested for hand/arm vibration levels, the operator was seated in the normal operating position with both hands on the steering mechanism. The engine was running and the cutting devic...
3 decals 14 3 decals familiarize yourself with the following decals. They are critical to the safe operation of the machine. Replace damaged decals immediately. 4164381 4181864 danger serious injury or death can result from blade contact or from objects being thrown very long distances. • do not ope...
Decals 3 15 familiarize yourself with the following decals. They are critical to the safe operation of the machine. Replace damaged decals immediately. 5002952 4181865 4181860 • read operator's manual. Do not allow untrained operators to use machine. • keep shields in place and hardware securely fas...
3 decals 16 3/4 1 1-1/4 1-1/2 1-3/4 2 2-1/4 2-1/2 2-3/4 3 3-1/4 3-1/2 3-3/4 4 4-1/4 4-1/2 4-3/4 5 5-1/4 cut height w/ 1/2 spacers cut height w/ 1/4 spacer 4133609 important t h i s m a c h i n e u s e s g r e e n s c a r e 6 8 , a b i o d e g r a d a b l e h y d r a u l i c f l u i d . ( o r d e r 5...
Decals 3 17 familiarize yourself with the following decals. They are critical to the safe operation of the machine. Replace damaged decals immediately. 3008521 3008682 tow valve vehicle can normal operation be towed (closed) (open) traction pedal reverseforward.
4 controls 18 4 controls 4.1 icons ___________________________________________________________________ warning never attempt to drive the mower unless you have read the safety, operation, & maintenance manual and know how to operate all controls correctly. Familiarize yourself with the icons shown a...
Controls 4 19 4.2 controls _______________________________________________________________ a e m u f j s v c b g k l r d h p n t w p e f a tilt steering lever b mow speed stop c traction pedal - forward d traction pedal - reverse e seat adjustment f hydraulic oil cap/dipstick g air cleaner indicator...
4 controls 20 a. Tilt steering lever pull lever up to release steering column. Tilt column up or down to position desired. Release lever to lock steering column in place. B. Mow speed stop limits forward speed while mowing. To operate at lower travel speed while mowing, rotate lever so it contacts s...
Controls 4 21 4.3 control panel _________________________________________________________ l. Horn switch this switch is used sound the horn. M. Warning lights when ignition switch (u) is turned to run position, glow plug light indicates that the glow plugs are energized. Wait until light goes out to...
4 controls 22 4.4 operator alerts_______________________________________________________ the combination gauge displays operating hours, fuel level, and has lights to alert operator to mower conditions. Figure 4b 4.4.1 indicator lights ___________________ the combination gauge has six indicator ligh...
Operation 5 23 5 operation 5.1 daily inspection ________________________________________________________ 1. Perform a visual inspection of the entire unit, look for signs of wear, loose hardware, and missing or damaged components. Check for fuel or oil leaks to ensure connections are tight and hoses...
5 operation 24 5.3 operating procedures_________________________________________________ 1. Under no circumstances should the engine be started without the operator seated on the mower. Never start the engine with operator or bystanders standing behind a discharge chute. 2. Never run the engine in a...
Operation 5 25 5.4 starting________________________________________________________________ 1. Sit in operator’s seat, make sure the pto switch (p) is off (down) and the parking brake switch (w) is on. Remove feet from pedals. Always use the seat belt when operating mowers equipped with a rops. 2. S...
5 operation 26 5.6 to drive / transport____________________________________________________ read and follow all safety notes contained in this manual when driving or transporting mower. When operating in reverse look behind you to ensure you have a clear path. Important: if this mower is driven on p...
Operation 5 27 5.9 hillside operation _____________________________________________________ the mower has been designed for good traction and stability under normal mowing conditions. Use caution when operating on slopes, especially when the grass is wet. Wet grass reduces traction and steering cont...
5 operation 28 how to calculate a slope: tools required: level (a), either 1 yard, or 1 meter long. Tape measure (b). With the level (a) positioned horizontally, measure the distance (c) with tape measure (b). Use the chart to calculate either the slope angle or the % grade of the slope (d). Figure ...
Operation 5 29 5.10 towing / trailering _____________________________________________________ if the mower experiences problems and must be shut down and removed from the area, it should be loaded onto a trailer for transport. If a trailer is not available, the unit can be towed slowly for short dis...
5 operation 30 5.11 daily maintenance _____________________________________________________ important: for more detailed maintenance information, adjustments and maintenance/lubrication charts, see sections 6, 7, and 8. 1. Park the mower on a flat, level surface. Fully lower the implements to the gr...
Maintenance & lubrication charts 6 31 6 maintenance & lubrication charts 6.1 general ________________________________________________________________ 1. Always clean grease fittings before and after lubrication. 2. Lubricate with grease that meets or exceeds nlgi grade 2 lb specifications. Apply gre...
6 maintenance & lubrication charts 32 6.3 lubrication chart _____________________________________________________ 1 1 1 1 2 2 2 2 2 3 3 3 3 3 3 3 3 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 6 7 8 8 9 9 10 10 12 12 12 11 grease fittings f1 - 50 hours (every week) 1 mower pivot (5) 2 lift arm pivot (5) 3 lift cyl...
Maintenance 7 33 7 maintenance 7.1 general ________________________________________________________________ 1. Adjustment and maintenance should always be performed by a qualified technician. If proper adjustments cannot be made, contact an authorized jacobsen dealer. 2. Inspect the equipment on a r...
7 maintenance 34 7.4 air filter_______________________________________________________________ check the service indicator daily. If red band appears in the window (b) replace the element. Do not remove the element for inspection or cleaning. Unnecessary removal of the filter increases the risk of i...
Maintenance 7 35 7.7 battery ________________________________________________________________ make absolutely certain the ignition switch is off position and the key has been removed before servicing the battery. Tighten cables securely to battery terminals and apply a light coat of silicone dielect...
7 maintenance 36 7.10 muffler and exhaust __________________________________________________ to protect from carbon monoxide poisoning, inspect the complete exhaust system regularly and always replace a defective muffler. If you notice a change in the color or sound of the exhaust, stop the engine i...
Maintenance 7 37 7.13 hydraulic filter _______________________________________________________ the hydraulic system is protected by a 10 micron return line filter. Flow though the filters is monitored during operation. When pressure drop across the filters is too high the hydraulic oil filter warnin...
7 maintenance 38 7.15 radiator _______________________________________________________________ check coolant level daily. Radiator should be full and recovery bottle should be up to the cold mark. Drain and refill annually. Remove the radiator cap, open the engine block drain and the radiator drain....
Maintenance 7 39 7.18 wheel mounting procedure ____________________________________________ 1. Remove dirt, grease and oil from stud thread. Do not lubricate threads. 2. Position wheel on hub and inspect to insure full contact between mounting surface of wheel and hub or brake drum. 3. Finger tighte...
7 maintenance 40 7.20 sharpening blades_____________________________________________________ 1. Place a wooden block between the blade and mower housing to stop the blade from moving. 2. When dressing or sharpening the blade, do not follow the original pattern of grind as shown in (a). Grind new cut...
Maintenance 7 41 7.22 storage ________________________________________________________________ general 1. Wash the mower thoroughly and lubricate. Repair and paint damaged or exposed metal. 2. Inspect the mower, tighten all hardware, replace worn or damaged components. 3. Drain and refill radiator. ...
8 adjustments 42 8 adjustments 8.1 general ________________________________________________________________ 1. Adjustments and maintenance should always be performed by a qualified technician. If proper adjustment cannot be made, contact an authorized jacobsen dealer. 2. Replace, do not adjust, worn...
Adjustments 8 43 8.4 neutral adjustment ___________________________________________________ neutral adjustment can only be made at the drive pump. The neutral adjustment is preset at the factory on all new mowers and replacement pumps. Further adjustment is not required unless the pump has been disa...
8 adjustments 44 8.6 steering toe-in _________________________________________________________ 1. Turn wheels to straight ahead position. 2. Loosen jam nuts (n) on both sides of tie rod (m). 3. Turn tie rod (s) to provide proper toe-in. Toe-in must not exceed +1/16 in. (+0.15 cm) (p). Re tighten jam...
Adjustments 8 45 8.8 cutting height _________________________________________________________ cutting height for decks can be adjusted from 3/4 to 5-1/4 in. (1.9-13.3 cm) in 1/4 in. (0.6 cm) increments. Actual cutting height may vary somewhat from the heights given depending on turf conditions and o...
8 adjustments 46 8.9 torque specification___________________________________________________ jacobsen uses grade 5 plated bolts as standard, unless otherwise noted. For tightening plated bolts, use the value given for lubricated. Notice all torque values included in these charts are approximate and ...
Problem solving 9 47 9 problem solving 9.1 general ________________________________________________________________ the problem solving chart below lists basic problems that may occur during start-up and operation. For more detailed information regarding the hydraulic and electrical systems contact ...
9 problem solving 48 9.2 controller lamps _____________________________________________________ the controller is a solid state device that monitors and controls electrical functions. The controller receives input signals from various switches and sensors throughout the machine and transmits output ...
Problem solving 9 49 9.3 electrical circuits ____________________________________________________ when troubleshooting the mower using the controller always check that program select (2) lamp is on. This indicates that the controller has power and the program is active. Individual circuits can be te...
10 quality of cut 50 10 quality of cut 10.1 quality of cut troubleshooting _______________________________________ it is recommended that a “test cut” be performed to evaluate the mower’s performance before beginning repairs. An area should be available where “test cuts” can be made. This area shoul...
Quality of cut 10 51 10.3 step cutting____________________________________________________________ note: arrow indicates direction of travel. Step cutting occurs when grass is cut taller on one side of a cutting unit than the other or on one side of mower to the other. This is usually caused by mech...
10 quality of cut 52 10.4 scalping _______________________________________________________________ note: arrow indicates direction of travel. Scalping is a condition in which areas of grass are cut noticeably shorter than the surrounding areas, resulting in a light green or even brown patch. This is...
Quality of cut 10 53 10.5 stragglers ____________________________________________________________ note: arrow indicates direction of travel. Stragglers are scattered blades of uncut or poorly cut grass. Probable cause remedy dull cutting blade(s). Sharpen blade(s). Mowing (ground) speed is too fast....
10 quality of cut 54 10.6 streaks ________________________________________________________________ note: arrow indicates direction of travel. A streak is a line of uncut grass. This is usually caused by a damaged blade. Probable cause remedy damaged blade(s). Replace blade(s). Turning too aggressive...
Quality of cut 10 55 10.7 windrowing ____________________________________________________________ note: arrow indicates direction of travel. Windrowing is the deposit of clippings concentrated at one end of cutting unit(s) or between cutting units, forming line(s) in the direction of travel. Probabl...
10 quality of cut 56 10.8 mismatched cutting units ______________________________________________ note: arrow indicates direction of travel. Mismatched cutting units is a pattern of varying cutting heights, resulting in a stepped cut appearance, usually due to mismatched hoc (height-of-cut) adjustme...
Notes 11 57 11 notes.
Nl-2 deze handleiding bevat veiligheids-, regelings- en bedieningsinstructies voor uw nieuwe jacobsen machine. Deze handleiding moet opgeslagen worden bij de machine voor raadpleging tijdens de bediening. Voordat u de machine gaat bedienen, moeten u en elke bediener zich inzetten beide handleidingen...
Inhoud nl-3 inhoud 1 veiligheid 1.1 hoe veilig werken...........................................4 1.2 belangrijke veiligheidsoverwegingen ............7 2 specificaties 2.1 productidentificatie ........................................8 2.2 v2403-m-di motor .........................................8 2...
1 veiligheid nl-4 1 veiligheid 1.1 hoe veilig werken _____________________________________________________ veilig werken a lees de bedieningshandleiding en ander opleidingsmateriaal. Indien de bediener of de monteur deze handleiding niet kunnen lezen, is het de verantwoordelijkheid van de eigenaar o...
Veiligheid 1 nl-5 d houd uw benen, armen en lichaam binnen het machinistcompartiment terwijl u de maaier gebruikt. Houd uw handen en voeten uit de buurt van de maaieenheden. E gebruik de maaier niet op hellingen groter dan de veilige maximumhelling voor de uitrusting. F bescherming tegen omkantelen ...
1 veiligheid nl-6 h vul het brandstofreservoir nooit volledig tot de rand. Laat ten minste 25 mm onder de vulnek. I draai de kap van het brandstofreservoir en de recipiënt altijd vast nadat u de brandstof hebt bijgevuld. J als u brandstof morst op uw kleding, moet u uw kleding direct vervangen. Onde...
Veiligheid 1 nl-7 1.2 belangrijke veiligheidsopmerkingen __________________________________ dit veiligheidssymbool wordt gebruikt om u te attenderen op potentiële gevaren. Gevaar - duidt op dreigende gevaarlijke situatie die, indien niet vermeden, zal resulteren in dood of ernstig letsel. Waarschuwi...
2 specificaties nl-8 2 specificaties 2.1 productidentificatie ___________________________________________________ 68131............................ Ar522-t4i, 5 gang 4wd met rops een identificatieplaat met het serienummer, zoals de getoonde, is aan het frame van de maaier bevestigd en bevindt zich a...
Specificaties 2 nl-9 2.5 maaieenheden __________________________________________________________ totale maaibreedte.......... 2,54 m aantal maaieenheden ..... Vijf – drie voor, twee achter. Maaihoogte ..................... 19 tot 133 mm met intervallen van 6 mm 2.6 accessoires ______________________...
2 specificaties nl-10 2.8 conformiteitsverklaring ______________________________________________ declaration of conformity ▪ ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ ▪ prohlÁŠenÍ o shodĚ ▪ overensstemmelseserklÆring ▪ conformiteitsverklaring ▪ vastavusdeklaratsioon ▪ vaatimustenmukaisuusvakuutus ▪ declaration de ...
Specificaties 2 nl-11 uk notified body for 2000/14/ec ▪ Нотифициран орган в Обединеното кралство за 2000/14/ЕО ▪ Úřad certifikovaný podle směrnice č. 2000/14/ec ▪ det britiske bemyndigede organ for 2001/14/ef ▪ engels adviesorgaan voor 2000/14/eg ▪ Ühendkuningriigi teavitatud asutus direktiivi 2000/...
2 specificaties nl-12 signature of the person empowered to draw up the declaration on behalf of the manufacturer, holds the technical documentation and is authorised to compile the technical file, and who is established in the community. Подпис на човека, упълномощен да състави декларацията от името...
Specificaties 2 nl-13 2.9 trillingsniveau_________________________________________________________ bij het testen van de machine op trillingsniveaus van hand/arm zat de machinist in de normale bedieningsstand met beide handen aan het stuur. De motor liep en de maai-inrichting draaide, met de machine...
3 decalplaatjes nl-14 3 decalplaatjes maak uzelf vertrouwd met de decalplaatjes die van essentieel belang zijn voor de veilige werking en bediening van de machine. Beschadigde decalplaatjes moeten onmiddellijk worden vervangen . 4164381 4181864 gevaar ernstig letsel of dodelijke ongelukken kunnen he...
Decalplaatjes 3 nl-15 maak uzelf vertrouwd met de decalplaatjes die van essentieel belang zijn voor de veilige werking en bediening van de machine. Beschadigde decalplaatjes moeten onmiddellijk worden vervangen . 4181865 4181860 • lees de bedieningshandleiding. Laat ongetraind personeel de machine n...
3 decalplaatjes nl-16 3/4 1 1-1/4 1-1/2 1-3/4 2 2-1/4 2-1/2 2-3/4 3 3-1/4 3-1/2 3-3/4 4 4-1/4 4-1/2 4-3/4 5 5-1/4 cut height w/ 1/2 spacers cut height w/ 1/4 spacer 4133609 important t h i s m a c h i n e u s e s g r e e n s c a r e 6 8 , a b i o d e g r a d a b l e h y d r a u l i c f l u i d . ( o...
Decalplaatjes 3 nl-17 maak uzelf vertrouwd met de decalplaatjes die van essentieel belang zijn voor de veilige werking en bediening van de machine. Beschadigde decalplaatjes moeten onmiddellijk worden vervangen . 3008521 3008682 sleepklep voertuig kan normale bediening gesleept worden (gesloten) (ge...
4 bediening nl-18 4 bediening 4.1 icoontjes ______________________________________________________________ waarschuwing probeer nooit met de maaier te gaan rijden voordat u de veiligheid- & bedieningshandleiding heeft gelezen en precies weet hoe het besturingssysteem werkt. Maak uzelf vertrouwd met ...
Bediening 4 nl-19 4.2 bediening _______________________________________________________________ a e m u f j s v c b g k l r d h p n t w p e f a kantelhendel stuurkolom b snelheidsstop maaien c tractiepedaal - vooruit d tractiepedaal - achteruit e stoel bijstellen f hydraulische oliedop/ peilstok g i...
4 bediening nl-20 a. Kantelhendel stuurkolom trek hendel omhoog om de kolom van de stuurinrichting vrij te geven. Kantel de kolom omhoog of omlaag naar de gewenste stand. Laat hendel los om de stuurkolom op zijn plaats te blokkeren. B. Snelheidsstop maaien deze beperkt de voorwaartse snelheid tijden...
Bediening 4 nl-21 4.3 bedieningspaneel ______________________________________________________ l. Claxonschakelaar deze schakelaar wordt gebruikt om de hoorn te activeren. M. Waarschuwingslichten wanneer de ontstekingsschakelaar (u) naar de stand 'run' wordt gedraaid, geeft het lampje van de gloeibou...
4 bediening nl-22 4.4 machinistwaarschuwingen ____________________________________________ de combinatiemeter toont de werkingsuren, het brandstofniveau en heeft lampjes om de machinist te waarschuwen wanneer er problemen met de maaier zijn. Afb. 4b 4.4.1 indicatielampjes __________________ de combi...
Operationele werking 5 nl-23 5 operationele werking 5.1 dagelijkse inspectie ___________________________________________________ 1. Voer een visuele inspectie van de volledige machine uit. Let daarbij op tekenen van slijtage, loszittende bevestigingen en ontbrekende of beschadigde onderdelen. Contro...
5 operationele werking nl-24 5.3 bedieningsprocedures_________________________________________________ 1. Onder geen enkele omstandigheid mag de machine worden gestart zonder dat de bediener op de bestuurdersplaats zit . Start de motor nooit als de operateur of omstanders achter een uitwerpschacht s...
Operationele werking 5 nl-25 5.4 starten ________________________________________________________________ 1. Ga op de bestuurdersplaats zitten en zorg dat de pto- schakelaar (p) in de uit-stand (middenpositie) staat en de parkeerrem (w) is aangetrokken. Haal uw voeten van de pedalen. Gebruik altijd ...
5 operationele werking nl-26 5.6 rijden / transport _____________________________________________________ alle in deze handleiding opgenomen veiligheids- aanwijzingen moeten worden gelezen en opgevolgd wanneer de maaier wordt gereden of getransporteerd. Bij achteruitrijden moet vooral goed achter de...
Operationele werking 5 nl-27 5.9 bediening op een helling _______________________________________________ de maaimachine werd ontworpen voor goede tractie en stabiliteit onder normale maaiomstandigheden. Wees voorzichtig bij het rijden op hellingen, vooral als het gras nat is. Nat gras vermindert de...
5 operationele werking nl-28 zo berekent u een helling: benodigd gereedschap: waterpas (a), van 1 yard of 1 meter lang. Meetlint (b). Als de waterpas (a) horizontaal is gepositioneerd meet u de afstand (c) met het meetlint (b). Gebruik de grafiek om de hellinghoek of het hellingspercentage van de he...
Operationele werking 5 nl-29 5.10 slepen / trailervervoer________________________________________________ als de maaier een probleem vertoont waarvoor hij uit bedrijf moet worden genomen en het werkgebied moet verlaten, dient het vervoer op een trailer te gebeuren. Als er geen trailer beschikbaar is...
5 operationele werking nl-30 5.11 dagelijks onderhoud __________________________________________________ belangrijk: voor meer gedetailleerde onderhouds- informatie, bijstellingen en onderhouds- en smeerschema’s, wordt u verwezen naar de onderdelen & onderhoud handleiding. 1. Parkeer de maaier op ee...
Onderhouds- en smeerschema’s 6 nl-31 6 onderhouds- en smeerschema’s 6.1 algemeen_______________________________________________________________ 1. Maak de vetsmeerpunten voor en na het smeren altijd schoon. 2. Smeer met vet dat voldoet aan de nlgi kwaliteit 2 lb specificaties of deze overtreft. Gebr...
6 onderhouds- en smeerschema’s nl-32 6.3 smeerschema __________________________________________________________ 1 1 1 1 2 2 2 2 2 3 3 3 3 3 3 3 3 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 6 7 8 8 9 9 10 10 12 12 12 11 smeerfittingen f1 - 50 uren (elke week) 1 draaipen maaier (5) 2 draaipen hefarm (5) 3 hefcilin...
Onderhoud 7 nl-33 7 onderhoud 7.1 algemeen ________________________________________________________________ 1. Afstelling en onderhoud behoren altijd te worden verricht door een bevoegd monteur. Als de gewenste afstelling niet kan worden uitgevoerd, neem dan contact op met een erkende jacobsen deale...
7 onderhoud nl-34 7.4 luchtfilter ____________________________________________________________ controleer de service-indicator dagelijks. Als de rode band in venster (b) verschijnt, dient het filter te worden vervangen. Verwijder het element niet voor inspectie of reiniging. Onnodige verwijdering va...
Onderhoud 7 nl-35 7.7 accu____________________________________________________________________ u moet er absoluut zeker van zijn dat de ontstekingsschakelaar in de uit-stand staat en de contactsleutel is verwijderd voordat u de accu een onderhoudsbeurt geeft. Zet de kabels stevig aan de accuklemmen ...
7 onderhoud nl-36 7.10 geluiddemper en uitlaat _______________________________________________ ter beveiliging tegen koolmonoxidevergiftiging moet het volledige uitlaatsysteem regelmatig worden geïnspecteerd. Een defecte uitlaat moet altijd worden vervangen. Als u een verandering waarneemt in de kle...
Onderhoud 7 nl-37 7.13 hydraulische filters __________________________________________________ het hydraulisch systeem wordt beschermd door twee 10 micron filters: een een terugleidingfilter. De stroming door de filters wordt tijdens de operationele werking gecontroleerd. Wanneer de drukdaling in de...
7 onderhoud nl-38 7.15 radiator _______________________________________________________________ controleer het koelvloeistofpeil dagelijks. De radiateur moet vol zijn en in de overloopfles dient het koud-streepje te worden bereikt. Het koelsysteem moet jaarlijks worden afgetapt en opnieuw gevuld. Ve...
Onderhoud 7 nl-39 7.18 wielmontageprocedure ________________________________________________ 1. Verwijder vuil, gras en olie van de tapboutdraadgangen, maar smeer ze niet. 2. Plaats het wiel op de naaf en controleer of er volledig contact is tussen het montagevlak van het wiel en de naaf of remtromm...
7 onderhoud nl-40 7.20 messen slijpen _________________________________________________________ 1. Plaats een houten blok tussen het mes en de maaibehuizing om het mes stil te zetten. 2. Volg bij het prepareren of slijpen van het mes niet het originele slijppatroon dat in (a) te zien is. Slijp nieuw...
Onderhoud 7 nl-41 7.22 stalling ________________________________________________________________ algemeen 1. De maaier dient eerst grondig te worden gewassen en gesmeerd. Repareer en lak beschadigd of blootgesteld metaal. 2. Inspecteer de maaier, draai alle bevestigingen vast en vervang versleten of...
8 afstellingen nl-42 8 afstellingen 8.1 algemeen ______________________________________________________________ 1. Afstellingen en onderhoud moeten altijd door een gekwalificeerde technicus worden uitgevoerd. Als er geen juiste afstelling kan worden gemaakt, neemt u dan contact op met een bevoegde j...
Afstellingen 8 nl-43 8.4 neutraalafstelling____________________________________________________ neutraalafstelling kan uitsluitend aan de drijfpomp worden uitgevoerd. De neutraalstand is een fabriekinstelling die geldt voor alle nieuwe maaiers en vervangingspompen. Verdere bijstelling is overbodig t...
8 afstellingen nl-44 8.6 wielsporing ____________________________________________________________ 1. Draai de wielen in de rechtuit-stand. 2. Los de contramoeren (n) aan weerszijden van de spoorstang (m). 3. Draai aan de spoorstang (s) om de juiste sporing te bereiken die niet meer dan + 1,5 mm mag ...
Afstellingen 8 nl-45 8.8 maaihoogte ____________________________________________________________ maaihoogte voor dekken kan worden aangepast van 19 tot 133 mm met intervallen van 6 mm. De eigenlijke maaihoogte kan afhankelijk van de toestand van de graszoden en andere factoren iets van de gegeven ho...
8 afstellingen nl-46 8.9 draaikoppelspecificatie _______________________________________________ jacobsen gebruikt kwaliteit 5 gegalvaniseerde bouten als standaard, tenzij anderszins vermeld. Bij het aandraaien van dergelijke bouten moet de waarde worden gebruikt die voor 'gesmeerd' wordt aangegeven...
Foutopsporing 9 nl-47 9 foutopsporing 9.1 algemeen_______________________________________________________________ onderstaande foutopsporingstabel vermeldt basisproblemen die zich kunnen voordoen tijdens start-up en werking. Voor meer gedetailleerde informatie betreffende de hydraulische en elektris...
9 foutopsporing nl-48 9.2 controllerlampjes ___________________________________________________ de controller is een halfgeleiderapparaat dat de elektrische functies controleert en bestuurt. De controller ontvangt ingangssignalen (inputs) van schakelaars en sensors die op diverse plaatsen in de mach...
Foutopsporing 9 nl-49 9.3 elektrische circuits ___________________________________________________ tijdens foutsporing in de machine met behulp van de controller, dient altijd eerst te worden gecontroleerd of programma actieve lampje (2) branden. Hiermee wordt namelijk aangegeven dat de controller v...
10 maaikwaliteit nl-50 10 maaikwaliteit 10.1 problemen met de maaikwaliteit oplossen ____________________________ het wordt aanbevolen om een ‘teststuk' te maaien om de prestaties van de maaier te evalueren voordat u de reparaties begint. Er moet een gebied beschikbaar zijn waar ‘teststukken’ gemaai...
Maaikwaliteit 10 nl-51 10.3 aflopend maaien _______________________________________________________ n.B: de pijl geeft de rijrichting aan. Aflopend maaien komt voor als het gras aan één kant van een haspel of snijeenheid langer wordt gemaaid dan aan de andere kant. Dit wordt meestal veroorzaakt door...
10 maaikwaliteit nl-52 10.4 scalperen _____________________________________________________________ n.B: de pijl geeft de rijrichting aan. Scalperen is een probleem waarbij stukken gras aanmerkelijk korter worden gemaaid dan de omringende gebieden, wat resulteert in een lichtgroen of zelfs bruin stu...
Maaikwaliteit 10 nl-53 10.5 achterblijvers ________________________________________________________ n.B: de pijl geeft de rijrichting aan. Achterblijvers zijn verspreide blaadjes ongemaaid of slecht gemaaid gras. Mogelijk probleem oplossing bot(te) snijmes(sen). Snijmes(sen) slijpen. (zie de onderde...
10 maaikwaliteit nl-54 10.6 strepen ________________________________________________________________ n.B: de pijl geeft de rijrichting aan. Een streep is een rechte lijn van ongemaaid gras. Dit wordt meestal veroorzaakt door een gedeukt of gebogen sledemes. Mogelijk probleem oplossing schade aan het...
Maaikwaliteit 10 nl-55 10.7 graszwaden ____________________________________________________________ n.B: de pijl geeft de rijrichting aan. Graszwaden zijn de afzettingen van gemaaid gras, geconcentreerd aan een uiteinde van de snijeenhe(i)d(en) of tussen twee snijeenheden, die een lijn vormen in de ...
10 maaikwaliteit nl-56 10.8 ongelijke snijeenheden________________________________________________ n.B: de pijl geeft de rijrichting aan. Ongelijke snijeenheden geven een patroon van variërende snijhoogten, wat resulteert in een getrapt maairesultaat, meestal door een ongelijke afstelling van de maa...
Opmerking 11 nl-57 11 opmerking.
Europa en de rest van de wereld behalve noord- en zuid-afrika ransomes jacobsen limited west road, ransomes europark, ipswich, ip3 9tt, engeland engels bedrijfsregistratienr. 1070731 www.Ransomesjacobsen.Com noord- en zuid-amerika jacobsen, a textron company 11108 quality drive, charlotte, nc 28273,...