- DL manuals
- Jacuzzi
- Hot Tub
- J - 210
- Owner's Manual
Jacuzzi J - 210 Owner's Manual - J-200
J-200
3.
!
DANGER:
RISK OF SEVERE INJURY OR DROWNING!
Body entrapment: May occur when part of the torso becomes
entrapped, inserted or sucked into a suction or outlet opening.
• Never allow children to play or get near the suction fittings, suction
covers, filter, filter lid or skimmer assembly.
4.
!
DANGER:
RISK OF SEVERE INJURY OR DROWNING!
Evisceration (disembowelment) entrapment: May occur when the
buttocks becomes entrapped, inserted or sucked into a suction or
outlet opening.
• Never sit on suction fittings, suction covers, filter, filter lid or skimmer
assembly.
• Never allow children to play or get near the suction fittings, suction
covers, filter, filter lid or skimmer assembly.
5.
!
DANGER:
RISK OF SEVERE INJURY OR DROWNING!
Mechanical entrapment: May occur when jewelry, swimsuit, or
hair accessories become entangled, knotted or snagged in a drain
suction or skimmer assembly.
• Never allow your jewelry, swimsuit, or hair accessories to come close
to the suction fittings, suction covers or skimmer assembly.
• Never allow children to play or get near the suction fittings, suction
covers, filter, filter lid or skimmer assembly.
3.2 Hyperthermia
Prolonged immersion in hot water may induce hyperthermia (over-
heating). The use of alcohol or drugs can greatly increase the risk of fatal
hyperthermia in spas. A description of the causes, symptoms, and effects
of hyperthermia are as follows.
Hyperthermia occurs when the internal temperature of the body reaches
a level several degrees above the normal body temperature of 98.6°F
(37°C). The symptoms of hyperthermia include drowsiness, lethargy
(fatigue), and an increase in the internal temperature of the body. The
effects of hyperthermia include:
• Unawareness of impending hazard;
• Failure to perceive heat;
• Failure to recognize the need to exit spa;
• Physical inability to exit spa;
• Fetal damage in pregnant women; and
• Unconsciousness and DANGER of drowning.
A Warning Sign is provided in your warranty packet. Please install at
a location near your spa, where it is visible to users of the spa. For
additional or replacement Warning Signs please contact your local
Jacuzzi dealer and reference item number #6530-082.
7
Summary of J - 210
Page 1
Owner’s manual j - 2 0 0 ™ c o l l e c t i o n j - 280 j - 275 j - 245 j - 235 j - 210 2530-277z rev. A.
Page 2: Attention New Spa Owner!
Attention new spa owner! Congratulations on the purchase of your new jacuzzi ® spa! The following is a list of automated functions performed by your spa. These functions are listed below in an attempt to alleviate any operational concerns you may have during the first 24 hours of ownership! Also lis...
Page 3: J-200
J-200 table of contents 1.0 important spa owner information .............................................. 1 2.0 fcc notice ................................................................................... 1 3.0 important safety instructions for all spa owners .................... 2 3.1 entrapment...
Page 4: J-200
J-200 12.6 maintaining the synthetic cabinet .............................................. 37 12.7 winterizing ................................................................................... 38 12.8 restarting your spa in cold weather .......................................... 39 13.0 water qua...
Page 5: J-200
J-200 1.0 important spa owner information your jacuzzi j-200 collection spa is constructed to the highest standards and is capable of providing many years of trouble-free use. However, because heat retentive materials are utilized to insulate the spa for efficient operation, an uncovered spa surface...
Page 6: J-200
J-200 3.0 important safety instructions for all spa owners read and follow all instructions carefully! This spa was manufactured to meet the standards and specifications outlined in the “virginia graeme baker pool and spa safety act” (vgb safety act). When installing and using this spa, basic safety...
Page 7: J-200
J-200 • a grounding wire connector is provided on this unit to connect a minimum no. 8 awg (8.4 mm²) solid copper conductor between this unit and any metal equipment, metal enclosures of electrical equipment, metal water pipe, or conduit within 5 feet (1.5m) of the unit. • never permit any electrica...
Page 8: J-200
J-200 6. ! Warning: risk of severe injury or death! • since excessive water temperatures have a high potential for causing fetal damage during the early months of pregnancy, if pregnant or possibly pregnant, consult your physician before using a spa. • pregnant or possibly pregnant women should limi...
Page 9: J-200
J-200 9. ! Warning: in addition to maintenance of filters and water chemistry, proper ventilation is recommended to reduce the risk of contracting a waterborne illness (e.G. An infection, bacteria or virus) and/or respiratory ailments that could be present in the air or water. Consult a licensed arc...
Page 10: J-200
J-200 3.1 entrapment risk the consumer products safety commission/usa has reported that users of pools and spas have become entrapped (stuck) to drain and/or suction fittings causing death, drowning, or serious injury (see diagram below). This spa was manufactured to meet the standards and specifica...
Page 11: J-200
J-200 3. ! Danger: risk of severe injury or drowning! Body entrapment: may occur when part of the torso becomes entrapped, inserted or sucked into a suction or outlet opening. • never allow children to play or get near the suction fittings, suction covers, filter, filter lid or skimmer assembly. 4. ...
Page 12: J-200
J-200 3.3 important csa safety instructions (canada only) when using this electrical equipment, basic safety precautions should always be followed, including the following: 1. Read and follow all instructions. 2. A green colored terminal or a terminal marked g, gr, ground, grounding or the symbol* i...
Page 13: J-200
J-200 4.0 choosing a location important: because of the combined weight of the spa, water and users, it is extremely important that the base upon which the spa rests be smooth, flat, level and capable of uniformly supporting this weight, without shifting or settling, for the entire time the spa is i...
Page 14: J-200
J-200 4.1 outdoor location in selecting the ideal outdoor location for your spa, we suggest that you take into consideration: • the proximity to changing area and shelter (especially in colder weather). • the pathway to and from your spa (this should be free of debris so that dirt and leaves are not...
Page 15: J-200
J-200 • proper drainage: it is extremely important to have in place measures to sufficiently handle excessive water spillage. Be sure the flooring in which the spa rests on has adequate drainage and can handle the entire contents of the spa. Be sure to make provisions for ceilings and other structur...
Page 16: J-200
J-200 120/240 volt convertible models a spa connected to a 120 vac electrical service must be located close enough to a grounded, grounding-type electrical outlet so that the included 10 feet (3m) power cord can be plugged directly into it. Do not use an extension cord as this could cause damage to ...
Page 17: J-200
J-200 all north american j-235/j-245/j-275/j-280 models (60 hz) 240v/40a* 240v/50a** 240v/60a*** circuit breaker (2-pole): 40a * 50a ** 60a *** number of wires: 3 3 3 frequency: 60 hz 60 hz 60 hz current draw: 26a 36a 45a * in 40a configuration, the heater will not operate while either jets pump is ...
Page 18: J-200
J-200 7.0 electrical wiring instructions important notice: the electrical wiring of this spa must meet the requirements of the national electrical code/usa (nec) and any applicable state or local codes. The electrical circuit must be installed by a qualified electrician and approved by a local build...
Page 19: J-200
J-200 6. The electrical circuit supplied for the spa must include a suitable ground fault circuit interrupter (gfci) as required by nec/usa article 680-42. 7. To gain access to the spa’s power terminal block, remove the screws securing the synthetic cabinet panel under the control panel (figure a). ...
Page 20: J-200
J-200 grn wht wht blk blk blk red 1 2 3 figure-c tb1 to circuit board power in grn wht wht blk blk blk red red red 1 2 3 figure-d tb1 to circuit board power in move red wire here north american convertible models: 120 vac, 3-wire connection 60 hz north american convertible models: 240 vac, 4-wire co...
Page 21: J-200
J-200 8.0 spa fill up procedure for best results, read each step in its entirety before proceeding with that step. 1. Prepare the spa for filling • clear all debris from the spa. (although the spa shell has been polished at the factory, you may want to treat it with a specially formulated spa cleane...
Page 22: J-200
J-200 5. Add start-up chemicals add the spa water chemicals as recommended by your authorized jacuzzi dealer. See section 13.0 “water quality maintenance” (page 39) for general guidance. Warning: risk of poisoning or death. Never leave chemicals opened and accessible to anyone. Use chemicals accordi...
Page 23: J-200
J-200 8. Place cover on spa • keeping the insulating cover in place anytime the spa is not in use will reduce the time required for heating, thereby minimizing operating costs. • the time required for initial heat-up will vary depending on the starting water temperature. Danger: risk of personal inj...
Page 24: J-200
J-200 10. Leave spa cover open during this step to allow excessive chemical vapors to exit spa, protecting pillows and plastic knobs from chemical attack. If spa is indoors, open doors and windows for proper ventilation. Turn on all jet pumps for one hour, then place the massage selector knob (if eq...
Page 25: J-200
J-200 warning: risk of personal injury. • to decrease the risk of injury, entrapment or drowning, never leave your hot tub unattended for any reason, especially if while the cover is open and accessible to small children and animals! • to decrease the risk of contracting a waterborne illness (e.G. A...
Page 26: J-200
J-200 9.0 control functions 9.1 control panel a. Led display: can display current water temperature (default display), water tem- perature set point, selected filtration/heat- ing mode, and error messages. B. Heat indicator: lit when heater is on. C. Jets 1 button: turns jets pump #1 on and off. Pre...
Page 27: J-200
J-200 9.2 general spa features and controls 1 2 1 6b 2 11 3 3 3 4 11 5 8 3 4 4 4 10 6a 9 7 7 7 11 11 2 2 2 12 13 13 13 13 13 13 13 13 14 14 14 14 15 17 16 16 16 16 1. Control panel 2. Headrest pillows (4 ea.) 3. Air controls (4 ea.) 4. Cup holders (4 ea.) 5. Massage selector (1 ea.) 6. Led lighting ...
Page 28: J-200
J-200 9.3 general spa features and controls (j-235/j-245/j-275) 1 2 1 2 2 2 13 3 3 3 3 15 6 6 6 6 4 4 4 11 5 5 8 8 8 8 8 8 14 14 14 10 9 7 17 16 16 16 16 16 16 16 16 16 16 12 12 12 specifications subject to change without notice. 1. Control panel 2. Air controls (3 ea.) 3. Optional audio system spea...
Page 29: J-200
J-200 10.0 operating instructions the spa control system has automatic functions that operate upon start-up and normal operation to protect the system. Upon power up, the readout displays the following information: 1. Control panel displays current software release (5.59) then; 2. Control panel disp...
Page 30: J-200
J-200 10.2 activate jet pumps the control panel jets 1 button activates jets pump 1. The first press activates low speed, the second press activates high speed, and the third press shuts jets pump 1 off. The jets 2 button activates jets pump 2. The first press activates high speed, the second press ...
Page 31: J-200
J-200 10.5 selecting desired massage action for models that incorporate a massage selector valve (diverter jet for j-210, figure a) that allows you to cus- tomize the massage and performance by diverting water between various jet systems within the spa. Simply turn valve to positions a, b or c to di...
Page 32: J-200
J-200 11.0 automatic filtration cycles the control system activates a programmable “standard” or “economy” filtration cycle to remove debris from your spa. These cycles use the low speed jets pump 1 and filter cartridge to quickly clear “skim” the water of debris and minimize their “bathtub ring” af...
Page 33: J-200
J-200 11.5 filtration modes for spas during the filtration/heating cycle the jets pump 1 low speed will activate. To set a time for the first filtration/heating cycle, simply turn power on to the spa two minutes prior to the desired time. Example: if you desire your first filtration/heating cycle to...
Page 34: J-200
J-200 11.6 programming the clearray (ultraviolet) water purification system a. Programming the clearray system (u) or corona discharge ozone (o3) press and hold the jets pump 1 ( 1 ) and cooler ( ) button at the same time for 3 seconds to enter the sanitizing system program. The screen will display ...
Page 35: J-200
J-200 b. Resetting the duration countdown timer (clearray® system only) once the duration countdown timer for the clear ray system has reached zero, you will need to reset it, replace the uv bulb and clean the quartz tube. To reset the duration countdown timer: 1 press press 1. Press and hold jets p...
Page 36: J-200
J-200 12.0 spa maintenance proper and regular maintenance of your spa will help it retain its beauty and performance. Your authorized jacuzzi dealer can supply you with all the information, supplies, and accessory products you will need to accomplish this. Danger: risk of severe injury or drowning b...
Page 37: J-200
J-200 3. Remove the filter cartridge by rotating it counterclockwise to unthread it from the filter wall fitting (figure b). Then lift it straight up to remove from filter well (figure c). 4. Using a garden hose with a high-pressure nozzle, rinse debris from the filter pleats beginning at the top an...
Page 38: J-200
J-200 j-280 models: these model spas are equipped with a skimmer bag and one high performance pleated filter cartridge located under the filter cover. Debris are filtered by drawing water through the skimmer bag and filter cartridge when jets pump 1 is running a programmed filter cycle or when manua...
Page 39: J-200
J-200 e lift unthreaded filter cartridge from skimmer well. F rinse debris from filter cartridge pleats using a garden hose and high-pressure nozzle. Start at the top and work downward to the handle. Repeat until all pleats are clean. Trapped air bubbles cartridge g submerge filter cartridge in spa....
Page 40: J-200
J-200 12.2 draining and refilling about every 3 months, you will want to replace the spa’s water. The frequency depends on a number of variables including the amount of use, attention paid to water quality maintenance, etc. You will know it is time for a change when you cannot control sudsing and/or...
Page 41: J-200
J-200 returned to the spa when the sanitizer reading is stable as recommended on the inside cover of the manual. 12.4 cleaning the spa interior to preserve the sheen of your spa’s surface, it is crucial that you avoid using abrasive cleaners or cleaners which have adverse chemical effect on the surf...
Page 42: J-200
J-200 caution: never spray cabinet with a garden hose for any reason since this action may induce an electrical short in the spa’s electrical equipment. 12.7 winterizing your jacuzzi spa is designed to automatically protect itself against freezing when operating properly. During periods of severe fr...
Page 43: J-200
J-200 safe location. Remove and dry off the quartz tube then reinstall it. Depending on the length of time, consider replacing the uv bulb when you resume use of your hot tub. 9. Re-install synthetic cabinet side panel and cover spa so that no casual moisture can enter into it. Consult your authoriz...
Page 44: J-200
J-200 13.1 ph control ph is a measure of relative acidity or alkalinity of water and is measured on a scale of 0 to 14. The midpoint of 7 is said to be neutral, above which is alkaline and below which is acidic. In spa water, it is very important to maintain a slightly alkaline condition of 7.4 to 7...
Page 45: J-200
J-200 13.3 clearray® water purification system clear ray water purification system is exclusive technology utilizing natural ultraviolet technology to eliminate waterborne bacteria, viruses, and algae in portable spas. The ultraviolet light otherwise know as uv-c or germicidal light inactivates the ...
Page 46: J-200
J-200 13.4 clearray® lamp replacement and quartz tube maintenance important: it is mandatory that the uv bulb is replaced and the quartz tube be cleaned every 12 months to maintain optimum performance. ! Danger: turn the spa breaker to the off position! ! Warning: drain the spa if you are replacing ...
Page 47: J-200
J-200 3. Remove the black bulb boot (8) by sliding it over the cable away from the quartz seal compression nut (7), figure 3. 4. Slowly remove the uv bulb (4) out of the quartz tube. 5. Remove bulb socket (5) from the uv bulb (4), figure 4. 6. Remove the quartz seal compression nut (7) by turning it...
Page 48: J-200
J-200 14. System test 1: assure there is no water dripping from the seal compression nut (7). If water is visible, stop and tighten the compression nut (7) using a pair of channel lock pliers to a maximum of 1/4 turn. If that does not fix the leak, then repeat quartz tube maintenance process from st...
Page 49: J-200
J-200 14.0 error conditions/error messages your spa has a self-diagnostic control system. The system will automatically display the following if a problem is detected. Always insist on genuine jacuzzi replacement parts. 14.1 panel displays col cool condition - temperature has dropped 20°f (11°c) bel...
Page 50: J-200
J-200 14.6 panel displays oh warning: risk of hyperthermia (over-heating) causing severe injury, burns, or welts. ! Water temperature is above acceptable limits. Do not enter spa! Water temperature has reached 112°f (44°c) and the low speed jets pump 1 has activated to circulate water through heater...
Page 51: J-200
J-200 15.2 pump does not operate but light does press the jets 1 button: 1. If no water movement is detected, make sure power is going to the spa and check the water level. If it does not solve the problem, contact your authorized jacuzzi dealer or qualified service technician. 2. The main jets pump...
Page 52: J-200
J-200 16.0 circuit board diagrams 16.1 north american j-235, j-245, j-275 and j-280 models this wiring diagram is used for the 240v 60 hz north american spa models. Or mini-din cable provides constant 12 v ac from yellow transformer wires mini-din control panel cable light dcu 1 2 3 4 5 6 7 8 9 10 p...
Page 53: J-200
J-200 16.2 north american j-210 convertible models this wiring diagram is used for all j-210 120/240v 60 hz north american convertible spa models. Light dcu 1 2 3 4 5 6 7 8 9 10 power exp bar exp bar wht wht wht wht wht wht blk blk blk blk blk blk blk blk red red red * red * red * red j2 j3 hi lo j1...
Page 54: J-200
J-200 16.3 export 50 hz j-235, j-245, j-275 and j-280 models this wiring diagram is used for the 230v 50 hz export spa models. Light dcu 1 2 3 4 5 6 7 8 9 10 power exp bar exp bar brn blu c circ. Pump stereo power supply clear r ay grn tb1 blu blu j6 brn j5 brn blu blk blu brn blu brn blu blu brn br...
Page 55: J-200
J-200 16.4 export 50 hz j-210 models this wiring diagram is used for all j-210 230v 50 hz export spa models. Transformer 230 v ac j1 logic jumper settings jp1 1-2 on = 20a logic (factory setting) jp1 1-2 off = 30a logic jp1 7-8 on = °c temperature display (factory setting) jp1 7-8 off = °f temperatu...
Page 56: J-200
J-200 17.0 optional bluewave™ spa stereo system to start enjoying your new stereo receiver, please read the following operation instructions in their entirety. 1. Media locker handle slide the handle to lock and unlock the protective door. 2. Power button press power button once to turn “on” stereo ...
Page 57: J-200
J-200 warning: risk of electrical shock hazard exists and equipment damage! Never install or remove electrical devices (e.G. Apple device/mp3/usb/aux/ bluetooth) while hands are wet or while sitting partially or fully immersed in the spa! Caution: never leave electrical devices in the media locker w...
Page 58: J-200
J-200 2. Treble setting: press the audio button 2 times to access the treble setting. The lcd display will change to “tre 0,” figure e. Press the up button to adjust the setting to a maximum of +5. Press the down button to adjust the setting down to -5. Note: the default setting is “0.” this feature...
Page 59: J-200
J-200 9. Stereo setting: press the audio button 9 times to access the stereo setting. The lcd display will change to “stereo,” figure m. Press the up button to select either stereo or mono. 17.3 wireless remote control functions a wireless radio frequency (rf) remote control is supplied on all spas ...
Page 60: J-200
J-200 17.4 electronic device connections and functions important: • if stereo unit is “on” (blue light is illuminated on the stereo power button) then press the power button on the remote once. • if stereo unit is in “standby” mode (red light is illuminated on the stereo power button) then press the...
Page 61: J-200
J-200 b. Connecting your apple device and mp3 player using the usb: 1. Locate the usb port in the stereo locker (figure b). 2. Locate the 30-pin cable provided for compatible devices (figure c) or a cable provided with your device. 3. Connect the usb end of the cable into the usb connection on stere...
Page 62: J-200
J-200 4. While the music is playing the remote screen will display and continually scroll through the following: title, song, artist, album, dir, music and track information. 5. For operational functions refer to the “external media device playback” section. E. Connecting your auxiliary player using...
Page 63: J-200
J-200 17.5 wireless remote battery replacement procedure 1. Turn the remote unit over and locate the battery door (figure a). 2. Rotate the battery door, with a coin, counterclockwise to the open position (figure b). When the door is unlocked it will pop up slightly. 3. Remove battery door by liftin...
Page 64: J-200
J-200 60