Jandy FHPM Installation And Operation Manual - Caution
Page 10
ENGLISH
Jandy
®
Pro Series FHPM Pump
|
Installation & Operation Manual
RECOMMENDED MINIMUM WIRE SIZE (AWG) FOR FHP PUMPS*
Distance from Sub-Panel
0-50 Feet
50-100 Feet
100-150 Feet
150 Feet-200 Feet
Model
Branch Fuse AMPS
Class: CC, G, H, J, K,
RK, or T
Voltage
Voltage
Voltage
Voltage
230 VAC 115 VAC
230 VAC
115 VAC
230 VAC
115 VAC
230 VAC
115 VAC
230 VAC
115 VAC
FHPM0.75HP
15A
15A
14
12
12
8
10
6
8
6
FHPM1.0HP
15A
20A
14
10
10
8
8
6
8
4
FHPM 1.5HP
15A
20A
12
10
10
6
8
6
6
4
FHPM2.0HP
15A
20A
12
8
8
6
6
4
6
3
FHPM 2.5HP
15A
N/A
12
N/A
8
N/A
6
N/A
6
N/A
FHPM1.0HP-2-Speed
15A
N/A
14
N/A
10
N/A
8
N/A
8
N/A
FHPM 1.5HP-2-Speed
15A
N/A
12
N/A
10
N/A
8
N/A
6
N/A
FHPM2.0HP-2-Speed
15A
N/A
12
N/A
8
N/A
6
N/A
6
N/A
*Assumesthree(3)copperconductorsinaburiedconduitand3%maximumvoltagelossinbranchcircuit.AllNationalElectricalCode
®
(NEC
®
)and
local codes must be followed. Table shows minimum wire size and branch fuse recommendations for a typical installation per NEC.
Table 3. Recommended Minimum Wire Size for FHP Pumps
Failuretoprovidedataplatevoltage(within10%)
during operation will cause the motor to overheat
and void the warranty.
CAUTION
3.2.2 Bonding and Grounding
1.
In addition to being properly grounded as
described below in Sec. 3.2.3, and in accordance
with the requirements of the National Electrical
Code (NEC), or in Canada the Canadian
Electrical Code (CEC), the pump motor must
be bonded to all metal parts of the swimming
pool, spa or hot tub structure and to all electrical
components and equipment associated with the
pool/spa water circulation system.
2.
The bonding must be accomplished by using a
solid copper conductro, No. 8 AWG or larger.
In Canada No. 6 AWG or larger must be used.
Bond the motor using the external bonding lug
provided on the motor frame.
To avoid the risk of property damage, severe
personal injury, and/or death, always disconnect
the power source before working on a motor or its
connected load.
WARNING
To avoid the risk of property damage, severe
personal injury, and/or death, make sure that
the control switch or time clock is installed in an
accessible location so that in the event of an
equipmentfailureoralooseplumbingfittingthe
equipmentcanbeturnedoff.Thislocationmustnot
beinthesameareaasthepoolpump,filter,and
otherequipment.
WARNING
The pump must be permanently connected to a
dedicatedelectricalcircuit.Nootherequipment,
lights, appliances or outlets may be connected to
the pump circuit, with the exception of devices that
mayberequiredtooperatesimultaneouslywiththe
pump, such as a chlorinating device or heater.
CAUTION
3.2.3 Electrical Wiring
To avoid risk of property damage, severe personal
injury, or death, always ground before connecting to
an electrical power supply.
WARNING
1.
The pump motor must be securely and
adequately grounded using the green screw
provided. Ground before attempting to connect
to an electrical power supply. Do not ground to
a gas supply line.
2.
Wire size must be adequate to minimize a
voltage drop during the start-up and operation
of the pump. See Table 3 for suggested wire
sizes.
3.
Insulate all connections carefully to prevent
grounding or short-circuits. Provide extra
protection for sharp edges on terminals. To
prevent wire nuts from loosening, tape them
using a suitable, listed (UL, ETL, CSA)
electrical insulating tape. For safety, and to
prevent entry of contaminants, reinstall all
conduit and terminal box covers. Do not force
connections into the conduit box.
4.
To configure the internal wiring of the pump
motor for the correct voltage, refer to the
diagram on the motor data plate.