Javad TRIUMPH-LS Quick Start Manual - page 25
www.javad.com
www.javad.com
49
48
Collect
Collect
Screen Anatomy - Collect Action Screen
The map displaying point and lines
contained in pages that are enabled.
To expand the User Defined Buttons
press the Action hardware button.
Maximizes map view to full screen
Unassigned User Defined
Button, tap to assign
Tap once to preform the action
associated with the User Defined
Button (AKA White Box); long click
(touch and hold) to remove or change
the User Defined Button
Shortcut to the applicable RTK corrections com-
munications screen; Currently corrections are
being received through WiFi with a 100% link
quality and full signal strength (as displayed by
the full bars of the signal strength icon)
Begin collecting a point; the current
time is displayed on the 2nd line
Shortcut to Selection of the type of
feature being located; Point, Line
Curve, Trajectory or Shift; choose by
Survey or by Offset
Returns to the previous screen
Center map on current location
Zoom in, the scale is displayed as the
distance across the bottom of the
screen (between the user defined
boxes).
Shortcut to Satellite Status screen;
displays the number of satellites
being used + the number of
additional satellites tracked but
not used
Number of engines fixed/number of
engines required by user
Shortcut to the Action Setup screen;
the pitch (forward/back), roll (left/
right), and the azimuth or bearing
the unit is facing are displayed. This
box turns orange if the device is
tilted more that 5 ° with Correct for
Tilts off, or more than 30 ° degrees
with Correct for Tilts enabled. When
orange it prevents accepting of
epochs in all modes except trajectory.
Zoom out
Current location in current Page
Cycle through AutoZoom and 1:1
Zoom modes
* Total number of SVs obsered by RTK
Rover may be different from number
of SVs observed by RTK Base
Instantaneous RMS estimate of the
current position solution
The current RTK correction rate being received
“FIX” (Fixed), “FLT” (Float), ”CDF” (WAAS Code
Differential Float) or “STN” (Standalone) solution types
are indicated. Tap this box to open the RTK V6+ screen..
Shortcut to the Review screen
Correct for Tilts: On*
Stakeout - To be used for staking out points (See Stake
section of this manual). Staking point in areas of high
multipath still requires confirming matching fixed initiations
acquired at least 2 minutes apart. The Boundary profile can
be used for this. After the location of the point being staked
has been verified, Verify with V6 Resets can be turned off to
quickly fine tune the location of the point being staked.
Start with Start Button
Stop After: 30 epochs
Minimum Duration: 30 seconds
Verify with V6 Reset
Confidence Level: 5
Consistency Counter: 10
Min RTK Engines: At least 2
Validate Result: with at least 2 engines
Correct for Tilts: Off
In all above cases
Accept Fixed Only, RMS: All, PDOP: All
Confidence Guard: 0.164 ft
WAAS Float - This profile can be used to quickly collect
points with float solutions. SBAS tracking must be enabled
to acquire WAAS (Wide Area Augmentation System,
available in North America) float solutions. SBAS tracking
can be enabled from the Advanced Setup menu (press the
Set Up hardware button twice > GNSS).
If you wish to review point statistics or if you wish to edit the
ShapeTag, Code, Description and/or Attributes fields after
data collection, Auto Accept must be set to Off. If these
fields do not need to be changed and you desire fast data
collection with the Quick Topo settings, set Auto Accept to
On.
*If Correct for Tilts is on, the Level Offsets must be calibrated
frequently if accuracies greater than 0.10’ are needed.
If the point you are attempting to locate is near the edge
of a building, tree trunk or other obstruction, it often best
to use one of the CoGo Offset functions. When the most
accurate measurements are needed, the CoGo Resection
function found in the Intersections menu is recommended.
Antenna Height
D-SNR loss, displays the level (in dB) of
the signal strength loss and interfer-
ence in the L1 / L2 GPS and GLONASS
bands. Values 0-3 are desirable, 3-6
are fair and above 6 are poor.