Venue ™ series sub10 amplifier/subwoofer service manual jbl consumer products 250 crossways park dr. Woodbury, new york 11797 rev2 8/2006.
- contents - basic specifications……………….….….….….…………….1 packaging…………………………….………………………......2 detailed specifications ……..…………….……………..3 connections..……………………………………………………5 operation ………….……………………………..…………….7 test set-up and procedure……..……….…….………….8 exploded view/parts list…………………………………..9 block di...
Sub10 venture series 2.
Jbl venue sub10 150w powered sub/ plate amp line voltage yes/no hi/lo line unit notes us 120vac/60hz yes 108-132 vrms normal operation eu 230vac/50-60hz yes 207-264 vrms normal operation, moms required asia 100vac/50hz yes 90-110 vrms normal operation parameter specification unit qa test limits cond...
Parameter specification unit qa test limits conditions notes power on delay time 3 sec. Functional ac power applied transients/pops ato transient 5 mv-peak 10 @ speaker outputs turn-on transient 50 mv-peak 100 @ speaker outputs ac line cycled from off to on turn-off transient 50 mv-peak 100 @ speake...
System connections if you have a dolby ® digital or dts ® receiver/processor with a low-frequency- effects (lfe) or subwoofer output: receiver/amplifier front speaker output in l r subwoofer or lfe output 0 0 andby in l r this figure shows how to connect bare wires to the speaker-level terminals. If...
Risk of electric shock do not open c aution risk of electric shock do not open c aution risk of electric shock do not open sub10 power ac 120v~60hz 250 watts t3.15a l/250v "war ning: for continued protection against risk of fire, replace only with same type t 3.15a l/250v fuse" "ave r tis s e me nt:...
Power on plug your subwoofer’s ac cord into a wall outlet. Do not use the outlets on the back of the receiver. Initially set the subwoofer-level control ¢ to the “min” position. Turn on your sub by pressing the power switch ª on the rear panel. Turn on your entire audio system and start a cd or movi...
Sub10 test set up and procedure equipment needed: • function/signal generator/sweep generator • integrated amplifier • multimeter • speaker cables general unit function (uut = unit under test) 1) from the signal generator, connect line level (rca) cables to the subwoofer line level input jacks l/r o...
Sub10 venture series 9.
Sub10 venture series 10
Sub10 120v electrical parts list part number description qty reference designator preamp pcb resistors 110-12472j52-e resistor4.7k 1/2w ±5% cf 52mm (rohs) 2 r201,r202 110-16102j26-e resistor 1k 1/6w ±5% cf 26mm (rohs) 4 r213,r214,r215,r254 110-16103j26-e resistor10k 1/6w ±5% cf 26mm (rohs) 15 r209,r...
Part number description qty reference designator preamp pcb 195-10204hgw-e double color led 204hgw 3￠(rohs) 1 d209, miscellaneous 162-50062001-e 2pin 60mm red/black 1 for d209, 174-0rca326p-e jack rca-326 (rohs) 1 jk201, 174-2wp810a-e spk jack 8p red up black down with cap 1 jk203, 175-1c07v01-e wir...
Part number description qty reference designator main pcb 135-3226m50-e electrolytic cap 22u 50v ±20% 2 c505,c506, 135-3227m16-e electrolytic cap 220u 16v ±20% 1 c118, 135-3476m16-e electrolytic cap47u 16v ±20% 1 c318, semiconductors 190-16tl074cn-e *i.C tl074cn st (rohs) dual op-amp 1 u301 192-161t...
Part number description qty reference designator class d ass'y pcb (replacment of entire module is recommended, part# 051-b00012a-e). Semiconductors 190-16tl072dts-e smd i.C. Tl072cdt sgs thomson dual op-amp 1 ic1, 192-09124126qs-e smd transistor 2sc2412k-t146q/r 3 q1,q4,q5, 192-09139066rs-e smd tra...
Sub10 venture series 15.
Sub10 venture series 16.
Sub10 venture series 17.
Sub10 venture series 18.
Sub10 venture series 19.
Sub10 venture series 20
, ic1 sub10 venture series 21.
Sub10 venture series 22.
Sub10 venture series 23.
Sub10 venture series 24.
Sub10 venture series 25.
