1. DL manuals
  2. Jeep
  3. Automobile
  4. 2014 Compass
  5. Owner's Manual

Jeep 2014 Compass Owner's Manual

Summary of 2014 Compass

  • Page 1

    Compass o w n e r ’ s m a n u a l 2 0 1 4.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the feat...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 rollover warning . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .5 䡵 warnings and cautions . . . . . . . . . . . . . .7 䡵 vehicle identification number . . . . . . . .7 ...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million a...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owners manual contains warnings against oper- ating procedures that could result in a collision or bodily injury. It also contains cautions against procedures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss important ...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right front body vin location 8 introduct...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . .12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .12 ▫ locking doors with a key. . . . . . . . . . . . . . . .14 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .14 䡵 sentry...

  • Page 12

    ▫ sound horn with remote key lock . . . . . . . . .22 ▫ flash lights with remote key lock/unlock . . .23 ▫ using the panic alarm . . . . . . . . . . . . . . . . . .24 ▫ programming additional transmitters. . . . . . . .25 ▫ general information . . . . . . . . . . . . . . . . . . . .25 ▫ transmitter ...

  • Page 13

    ▫ energy management feature . . . . . . . . . . . . . .55 ▫ seat belt pretensioners . . . . . . . . . . . . . . . . . .55 ▫ supplemental active head restraints (ahr) . . .56 ▫ enhanced seat belt use reminder system (beltalert®) . . . . . . . . . . . . . . . . . . . . . . . . . .60 ▫ seat belt extend...

  • Page 14

    A word about your keys the authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition key removal 1. Place the shift lever in...

  • Page 15

    Note: if you try to remove the key before you place the shift lever in park, the key may become trapped tem- porarily in the ignition switch cylinder. If this occurs, place the shift lever in park, rotate the key to the right slightly, then remove the key as described. If a malfunc- tion occurs, the...

  • Page 16

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the shift lever. • do not leave the key fob in or near the ...

  • Page 17

    Sentry key® the sentry key® immobilizer system prevents unau- thorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys that have an embedded el...

  • Page 18

    Caution! The sentry key® immobilizer system is not compat- ible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the keys provided with your new vehicle have been programmed to the vehicle electronics....

  • Page 19

    Customer key programming if you have two valid sentry keys®, you can program new sentry keys® to the system by performing the following procedure: 1. Cut the additional sentry key® transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the igniti...

  • Page 20

    Note: if a programmed key is lost, see your authorized dealer to have all remaining keys erased from the sys- tem’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of s...

  • Page 21

    3. The vehicle security light in the instrument cluster will flash rapidly for approximately 16 seconds. This shows that the vehicle security alarm is arming. During this period, if a door is opened, the ignition switch is turned to on/run, or the power door locks are unlocked in any manner, the veh...

  • Page 22

    Vehicle security alarm manual override the vehicle security alarm will not arm if you lock the doors using the manual door lock plunger. Remote keyless entry (rke) — if equipped this system allows you to lock or unlock the doors and liftgate or activate the panic alarm from distances up to approxima...

  • Page 23

    To unlock the doors and liftgate press and release the unlock button on the rke transmitter once to unlock the driver’s door, or twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn...

  • Page 24

    Security alarm activated will cause the alarm to sound. Press the unlock button to deactivate the vehicle security alarm. Illuminated approach — if equipped this feature activates the headlights for up to 90 seconds when the doors are unlocked with the rke transmitter. The time for this feature is p...

  • Page 25

    • for vehicles not equipped with the evic, perform the following steps: 1. Press the lock button on a programmed rke trans- mitter for at least 4 seconds, but no longer than 10 seconds. Then, press the panic button while still holding the lock button. 2. Release both buttons at the same time. 3. Tes...

  • Page 26

    • for vehicles not equipped with the evic, perform the following steps: 1. Press and hold the unlock button on a programmed rke transmitter for at least 4 seconds, but no longer than 10 seconds. Then, press and hold the lock button while still holding the unlock button. 2. Release both buttons at th...

  • Page 27

    Programming additional transmitters refer to sentry key® “customer key programming.” if you do not have a programmed rke transmitter, contact your authorized dealer for details. General information this device complies with part 15 of fcc rules and with rs-210 of industry canada. Operation is subjec...

  • Page 28

    2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To reassemble the rke transmitter case, snap the two halves together. Note: if the rke transmitter is equipped wit...

  • Page 29

    How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in park • doors closed • hood closed • hazard switch off • brake switch inactive (brake pedal not pressed) • ignition key removed from ignition switch • battery at an acceptable cha...

  • Page 30

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted — door ajar • remote start aborted — hood ajar • remote start abor...

  • Page 31

    • the engine can be started two consecutive times (two 15-minute cycles) with the rke transmitter. However, the ignition switch must be cycled to the on/run position before you can repeat the start sequence for a third cycle. Remote start will also cancel if any of the following occur: • the engine ...

  • Page 32

    Door locks manual door locks use the manual door lock knob to lock the doors from inside the vehicle. If the lock knob is down when the door is closed, the door will lock. Make sure the keys are not inside the vehicle before closing the door. Warning! • for personal security and safety in the event ...

  • Page 33

    Caution! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. Power door locks a power door lock switch is located on the driver’s and front passenger’s door panel. Press this switch to lock or unlock ...

  • Page 34

    Auto lock doors — if equipped the auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). Auto lock doors programming the automatic door locks feature can be enabled or disabled as follows: • for veh...

  • Page 35

    Note: • if you do not hear the chime it means that the system did not enter the programming mode and you will need to repeat the procedure. • use the automatic door lock feature in accordance with local laws. Automatic unlock doors on exit the doors will unlock automatically if: • the automatic unlo...

  • Page 36

    3. Within 30 seconds, press the power door unlock switch to unlock the doors. 4. A single chime will indicate the completion of the programming. 5. Repeat these steps if you want to return this feature to its previous setting. Note: • if you do not hear the chime it means that the system did not ent...

  • Page 37

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Child-protection door lock location child-protection door lock function 2 things to know before starting your vehicle 35.

  • Page 38

    Note: for emergency exit with the system engaged, move the lock knob up (unlocked position), roll down the window and open the door with the outside door handle. Power windows — if equipped power window switches the window controls on the driver’s door trim panel control all the door windows. There ...

  • Page 39

    Auto-down the driver’s door window switch has an auto-down feature. Push the window switch past the first detent, release, and the window will go down automatically. To cancel the auto-down movement, operate the switch in either the up or down direction and release the switch. Window lockout switch ...

  • Page 40

    Liftgate note: the key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate. To unlock the liftgate, insert the key into the lock and turn it to the right (manual lock models only). The liftgate can also be unlocked using the remote keyless entry (rke) tra...

  • Page 41

    Note: • in the event of a power malfunction, or the rke transmitter is inoperative, insert the key into the liftgate lock cylinder and turn to the right (manual lock models only). Using the liftgate handle, pull the lift- gate open with one fluid motion. • although the liftgate has no inside release...

  • Page 42

    Occupant restraints some of the most important safety features in your vehicle are the restraint systems: • three-point lap and shoulder belts for all seating positions • advanced front air bags for driver and front passenger • supplemental active head restraints (ahr) located on top of the front se...

  • Page 43

    If you will be carrying children too small for adult-sized seat belts, the seat belts or the lower anchors and tether for children (latch) feature also can be used to hold infant and child restraint systems. For more information on latch, see lower anchors and tether for children (latch). Note: the ...

  • Page 44

    If a child from 2 to 12 years old (not in a rear facing child seat) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint. (refer to “child restraints”) you should read the instructions provided with your child restraint to make sure that you...

  • Page 45

    Warning! (continued) • supplemental side air bag inflatable curtain (sabic) and seat-mounted side air bags (sab) also need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. • in a collision, you and your passengers can suffer much greater injuries if you...

  • Page 46

    Lap/shoulder belts all seating positions in your vehicle are equipped with lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. However, in a colli...

  • Page 47

    Warning! (continued) • two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly. Never use a lap/shoulder belt or lap belt for more than one person, no matter what their size. Lap/shoulder belt operating in...

  • Page 48

    Warning! • a belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal inju- ries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you prop- erly. In a sudden stop you...

  • Page 49

    Warning! (continued) • a shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. 4. Position the lap belt across your thigh...

  • Page 50

    Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • a twisted belt may not protect you properly. In a collisi...

  • Page 51

    Adjustable upper shoulder belt anchorage in the front seat, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push the anchorage button to release the anchorage, and move it up or down to the position that fits you best. Note: the adjustable upper shoulde...

  • Page 52

    Second row center lap/shoulder belt operating instructions the second row center lap/shoulder belt features a three-point seat belt with a mini-latch and buckle, which allows the shoulder belt to detach from the lower anchor when the seat is folded. The mini-buckle and shoulder belt can then be stor...

  • Page 53

    4. When the belt is long enough to fit, insert the mini- latch plate into the mini-buckle until you hear a “click.” 5. Sit back in the seat. Slide the regular latch plate up the webbing as far as necessary to allow the belt to go around your lap. 6. When the belt is long enough to fit, insert the la...

  • Page 54

    7. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. 8. Position the shoulder bel...

  • Page 55

    10. To disengage the mini-latch from the mini-buckle for storage, insert the regular latch plate into the black button on the top of the mini-buckle. The belt will automatically retract to its stowed position. If neces- sary, slide the latch plate down the webbing to allow the belt to retract fully....

  • Page 56

    Driver center passenger first row n/a n/a alr second row alr alr alr • n/a — not applicable • alr — automatic locking retractor if the passenger seating position is equipped with an alr and is being used for normal usage: only pull the belt webbing out far enough to comfortably wrap around the occup...

  • Page 57

    3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the automati...

  • Page 58

    Note: these devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. The pretensioners are triggered by the occupant re- straint controller (orc). Like the air bags, the preten- sioners are single use items. A deplo...

  • Page 59

    Caution! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. Note: for more information on properly adjusting and positi...

  • Page 60

    1. Grasp the deployed ahr from the rear seat. 2. Position the hands on the top of the deployed ahr at a comfortable position. 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. Hand positioning points on ahr 1 — downward movement 2 — rearward moveme...

  • Page 61

    4. The ahr front soft foam and trim half should lock into the back decorative plastic half. Note: • if you have difficulties or problems resetting the active head restraints, see an authorized dealer. • for safety reasons, have the active head restraints checked by a qualified specialist at an autho...

  • Page 62

    Enhanced seat belt use reminder system (beltalert®) beltalert® is a feature intended to remind the driver and front passenger (if equipped with front passenger beltalert®) to fasten their seat belts. The feature is active whenever the ignition is on. If the driver or front seat passenger is unbelted...

  • Page 63

    Note: although beltalert® has been deactivated, the seat belt reminder light will continue to illuminate while the driver’s or front passenger (if equipped with beltalert®) seat belt remains unfastened. Seat belt extender if a seat belt is too short even when fully extended and when the adjustable u...

  • Page 64

    Supplemental restraint system (srs) — air bags this vehicle has advanced front air bags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s advanced front air bag is mounted in the center of the steering wheel. The passenger’s advanced front air b...

  • Page 65

    The advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation that are based on the severity and type of collision. This vehicle may be equipped with a driver and/or front passenger seat belt buckle switch that detects whether the driver ...

  • Page 66

    • steering wheel and column • instrument panel • knee impact bolsters • driver advanced front air bag • passenger advanced front air bag • supplemental seat-mounted side air bags (sab) • supplemental side air bag inflatable curtains (sabic) • front and side impact sensors • front seat belt pretensio...

  • Page 67

    Warning! (continued) • do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air ba...

  • Page 68

    When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air bag only. Supplemental side air bag inflatable curtain (sabic) sabic air...

  • Page 69

    • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • being too close to the supplemental side air bag inflatable curtain and/or seat-mounted side air bag during deployment could cause you to be severely injured or killed. The system includes side ...

  • Page 70

    Windows, or area where the sab or sabic air bags inflate, even if they are in an infant or child restraint. Always sit upright as possible with your back against the seat back, use the seat belts properly, and use the appropriate sized child restraint, infant restraint or booster seat recommended fo...

  • Page 71

    The advanced front air bags will not deploy in all frontal collisions, including some that may produce sub- stantial vehicle damage — for example, some pole colli- sions, truck underrides, and angle offset collisions. On the other hand, depending on the type and location of impact, advanced front ai...

  • Page 72

    It also includes diagnostics that will illuminate the instru- ment cluster air bag warning light if a malfunction is noted that could affect the air bag system. The diagnos- tics also record the nature of the malfunction. Warning! Ignoring the air bag warning light in your instru- ment panel could m...

  • Page 73

    Supplemental seat-mounted side air bag (sab) inflator units the supplemental seat-mounted side air bags (sab) are designed to activate only in certain side collisions. The orc determines if a side collision requires the side air bags to inflate, based on the severity and type of collision. Based on ...

  • Page 74

    Because air bag sensors estimate deceleration over time, vehicle speed and damage are not good indicators of whether or not an air bag should have deployed. Note: in a rollover the pretensioners and/or sab and sabic air bags may deploy on both sides of the vehicle. Front and side impact sensors in f...

  • Page 75

    If you do have a collision, which deploys the air bags, any or all of the following may occur: • the nylon air bag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the air bags deploy and unfold. The abrasions are similar to friction rope burns or tho...

  • Page 76

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 77

    Air bag warning light you will want to have the air bags ready to inflate for your protection in a collision. The air bag warning light monitors the internal circuits and interconnecting wiring associated with air bag system electrical components. While the air bag system is designed to be maintenan...

  • Page 78

    • whether or not the driver and passenger safety belts were buckled/fastened; • how far (if at all) the driver was depressing the accelerator and/or brake pedal; and, • how fast the vehicle was traveling. These data can help provide a better understanding of the circumstances in which crashes and in...

  • Page 79

    There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to make sure you have the correct seat for your child. Before buying any restraint system, make sure that it has a la...

  • Page 80

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child re- straint either an infant carrie...

  • Page 81

    Infants and child restraints safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carrie...

  • Page 82

    Have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat. Children should remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above t...

  • Page 83

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 84

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 85

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 86

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seat- ing position • top tether anchorage symbol 84 things to know before starting your vehicle.

  • Page 87

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and teth...

  • Page 88

    Can two child restraints be attached us- ing a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to install a child seat in the center position next to a child s...

  • Page 89

    Locating the latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between ...

  • Page 90

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear-facing infant restraint...

  • Page 91

    To install a latch-compatible child restraint 1. If the selected seating position has a switchable auto- matic locking retractor (alr) seat belt, stow the seat belt, following the instructions below. See the section “installing child restraints using the vehicle seat belt” to check what type of seat...

  • Page 92

    How to stow an unused alr seatbelt when using the latch attaching system to install a child restraint, stow all alr seat belts that are not being used by other occupants or being used to secure child restraints. An unused belt could injure a child if they play with it and accidentally lock the seatb...

  • Page 93

    Make a clicking noise while the webbing is pulled back into the retractor. For additional information on alr, refer to the “automatic locking mode” description un- der “occupant restraints.” the cinching latch plate is designed to hold the lap portion of the seatbelt tight when webbing is pulled tig...

  • Page 94

    What is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward facing child restraint...

  • Page 95

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. 2. Pull enough of the seat belt webbing fro...

  • Page 96

    8. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. Refer to “lower anchors and tethers for chil- dren (latch) restraint system” for directions to attach a tether anchor. 9. Test...

  • Page 97

    5. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. Refer to “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 6. Test that t...

  • Page 98

    2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat, routing it over the center of the head restraint. 3. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. 4. Remove slack in the tether s...

  • Page 99

    Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. Engine break-in recommendations a long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 k...

  • Page 100

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be serious...

  • Page 101

    Warning! (continued) • if it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. The best protection against carbon monoxide entry into the vehicle body is a properly maintained ...

  • Page 102

    Dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Defroster check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your author...

  • Page 103

    Warning! (continued) • check mounting of mats on a regular basis. Always properly reinstall and secure floor mats that have been removed for cleaning. • always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Ob- jects can become trapped under the brake pedal ...

  • Page 104

    Door latches check for positive closing, latching, and locking. Fluid leaks check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid (if equipped), or brake fluid leaks are suspected, t...

  • Page 105: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 ▫ inside day/night mirror . . . . . . . . . . . . . . . .108 ▫ automatic dimming mirror — if equipped . . .109 ▫ outside mirror — driver side . . . . . . . . . . . .110 ▫ outside ...

  • Page 106

    ▫ commands . . . . . . . . . . . . . . . . . . . . . . . . . .145 ▫ voice training . . . . . . . . . . . . . . . . . . . . . . . .149 䡵 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149 ▫ power seats — if equipped . . . . . . . . . . . . . .150 ▫ heated seats — if equipped . . . ....

  • Page 107

    䡵 windshield wipers and washers . . . . .170 ▫ windshield wiper operation . . . . . . . . . . . . .171 ▫ intermittent wiper system . . . . . . . . . . . . . . .172 ▫ windshield washers . . . . . . . . . . . . . . . . . . .172 ▫ mist feature . . . . . . . . . . . . . . . . . . . . . . . . .173 䡵 tilt...

  • Page 108

    ▫ troubleshooting tips . . . . . . . . . . . . . . . . . . .187 ▫ general information. . . . . . . . . . . . . . . . . . . .188 䡵 power sunroof — if equipped . . . . . . . .189 ▫ opening sunroof — express . . . . . . . . . . . . . .190 ▫ opening sunroof — manual mode . . . . . . . . .190 ▫ closing s...

  • Page 109

    ▫ fold down speakers — if equipped . . . . . . . .206 䡵 rear window features . . . . . . . . . . . . . .206 ▫ rear window wiper/washer . . . . . . . . . . . . .206 ▫ rear window defroster . . . . . . . . . . . . . . . . .207 䡵 roof luggage rack — if equipped . . . .208 3 understanding the features o...

  • Page 110

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicl...

  • Page 111

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activa...

  • Page 112

    Outside mirror — driver side adjust the flat outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle with your head close to the door glass. Outside mirror — passenger side adjust the convex outside mirror so you can just see the side of your vehi...

  • Page 113

    To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When you are finished adjusting the mirror, turn the control to the center position to prevent accidentally moving a mirror. Heated mirro...

  • Page 114

    Vanity mirrors — if equipped to use the vanity mirror, rotate the sun visor down and swing the mirror cover upward. Sun visor sliding feature the sun visors may be extended out to provide more coverage of the side glass. Uconnect® phone — if equipped uconnect® phone is a voice-activated, hands-free,...

  • Page 115

    For uconnect® customer support: • u.S. Residents - visit www.Uconnectphone.Com or call 1–877–855–8400. • canadian residents - visit www.Uconnectphone.Com or call, 1-800-465–2001 (english) or 1-800-387-9983 (french). Uconnect® phone allows you to transfer calls between the system and your mobile phon...

  • Page 116

    Uconnect® phone button the radio or steering wheel controls (if equipped) will contain the two control buttons (uconnect® phone button and voice com- mand button) that will enable you to access the system. When you press the button you will hear the word uconnect® followed by a beep. The beep is you...

  • Page 117

    • prior to giving a voice command, one must wait for the beep, which follows the “ready” prompt or another prompt. • for certain operations, compound commands can be used. For example, instead of saying “setup” and then “pair a device”, the following compound command can be said: “pair a bluetooth® ...

  • Page 118

    Pair (link) uconnect® phone to a mobile phone to begin using your uconnect® phone, you must pair your compatible bluetooth® enabled mobile phone. To complete the pairing process, you will need to refer- ence your mobile phone owner’s manual. The uconnect® website may also provide detailed instruc- t...

  • Page 119

    Phone when you make a call. You can select to use a lower priority mobile phone at any time (refer to “advanced phone connectivity” in this section). Dial by saying a number • press the button to begin. • after the “ready” prompt and the following beep, say “dial.” • the system will prompt you to sa...

  • Page 120

    • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook new entry.” • when prompted, say the name of the new entry. Use of long names helps the voice command and it is recom- mended. For example, say “robert smith” or “robert” instead of “bob.” • when prompted,...

  • Page 121

    • automatic download and update, if supported, begins as soon as the bluetooth® wireless phone connection is made to the uconnect® phone, for example, after you start the vehicle. • a maximum of 1000 entries per phone will be down- loaded and updated every time a phone is connected to the uconnect® ...

  • Page 122

    • when prompted, recite the new phone number for the phonebook entry that you are editing. After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu. “phonebook edit”...

  • Page 123

    • automatic downloaded phonebook entries cannot be deleted or edited. Delete/erase “all” uconnect® phonebook entries • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook erase all.” • the uconnect® phone will ask you to verify that you wish to delete all the...

  • Page 124

    Phone call features the following features can be accessed through the uconnect® phone if the feature(s) are available on your mobile service plan. For example, if your mobile service plan provides three-way calling, this feature can be accessed through the uconnect® phone. Check with your mobile se...

  • Page 125

    In progress. To go back to the first call, refer to “toggling between calls” in this section. To combine two calls, refer to “conference call” in this section. Place/retrieve a call from hold to put a call on hold, press the button until you hear a single beep. This indicates that the call is on hol...

  • Page 126

    Call termination to end a call in progress, momentarily press the but- ton. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automatically. This i...

  • Page 127

    • an active call is automatically transferred to the mo- bile phone after the ignition is cycled to off. Uconnect® phone features language selection to change the language that the uconnect® phone is using: • press the button to begin. • after the “ready” prompt and the following beep, say the name ...

  • Page 128

    The paired mobile phone to call the emergency number. This feature is supported in the u.S., canada, and mexico. Note: • the emergency number dialed is based on the country where the vehicle is purchased (911 for the u.S. And canada and 060 for mexico). The number dialed may not be applicable with t...

  • Page 129

    Note: you should program the desired towing assis- tance phone number using the voice command system. To do this, press the button and say “setup,” followed by “towing assistance.” when prompted say 1-800-528- 2069 for the u.S., say 1-800-363-4869 for canada, say 55-14- 3454 for mexico city and 1-80...

  • Page 130

    “send,” is also to be used for navigating through an automated customer service center menu structure, and to leave a number on a pager. You can also send stored uconnect® phonebook entries as tones for fast and easy access to voice mail and pager entries. To use this feature, dial the number you wi...

  • Page 131

    • after the “ready” prompt and the following beep, say one of the following: – “setup confirmation prompts on” – “setup confirmation prompts off” phone and network status indicators if available on the radio and/or on a premium display such as the instrument panel cluster, and supported by your mobi...

  • Page 132

    • following the beep, say “mute.” in order to un-mute the uconnect® phone: • press the button. • following the beep, say “mute off.” advanced phone connectivity transfer call to and from mobile phone the uconnect® phone allows ongoing calls to be trans- ferred from your mobile phone to the uconnect®...

  • Page 133

    • the uconnect® phone will play the phone names of all paired mobile phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the button and say “se- lect” or “delete.” also, see the next two sections for an alternate way to “select” or “...

  • Page 134

    Things you should know about your uconnect® phone uconnect® phone tutorial to hear a brief tutorial of the system features, press the button and say “uconnect® tutorial.” voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers, the uconnect® pho...

  • Page 135

    This will delete all phone pairing, phone book entries, and other settings in all language modes. The system will prompt you before resetting to factory settings. Voice command • for best performance, adjust the rearview mirror to provide at least ½ in (1 cm) gap between the overhead console (if equ...

  • Page 136

    • phonebook (downloaded and uconnect® phone lo- cal) name recognition rate is optimized when the entries are not similar. • numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred.” • you can say “o” (letter “o”) for “0” (zero). • even though international ...

  • Page 137

    Voice text reply uconnect® phone can read or send new messages on your phone. Read messages: if you receive a new text message while your phone is connected to uconnect® phone, an announcement will be made to notify you that you have a new text message. If you wish to hear the new message: • press t...

  • Page 138

    3. Where are you? 4. I need more direction. 5. L o l 6. Why 7. I love you 8. Call me 9. Call me later 10. Thanks 11. See you in 15 minutes 12. I am on my way 13. I’ll be late 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye for now 18. When can we meet? 19. Send number to ...

  • Page 139

    Bluetooth® communication link mobile phones have been found to lose connection to the uconnect® phone. When this happens, the connection can generally be reestablished by switching the phone off/on. Your mobile phone is recommended to remain in bluetooth® on mode. Power-up after switching the igniti...

  • Page 140

    138 understanding the features of your vehicle.

  • Page 141

    3 understanding the features of your vehicle 139.

  • Page 142

    140 understanding the features of your vehicle.

  • Page 143

    Voice commands primary alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location voice commands primary alternate (s) all call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais 3 understanding th...

  • Page 144

    Voice commands primary alternate (s) help home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book voice commands primary alternate (s) previous record again redial return to main menu return or main menu select phone select...

  • Page 145

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 146

    Warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. When you press the voice command button, you...

  • Page 147

    To hear the first available menu, press the voice com- mand button and say “help” or “main menu.” commands the voice command system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the volum...

  • Page 148

    Radio am to switch to the am band, say “am” or “radio am.” in this mode, you may say the following commands: • “frequency #” (to change the frequency) • “next station” (to select the next station) • “previous station” (to select the previous station) • “radio menu” (to switch to the radio menu) • “m...

  • Page 149

    Disc mode to switch to the disc mode, say “disc.” in this mode, you may say the following commands: • “track” (#) (to change the track) • “next track” (to play the next track) • “previous track” (to play the previous track) • “main menu” (to switch to the main menu) usb mode to switch to usb mode, s...

  • Page 150

    – “continue” (to continue recording) – “delete” (to delete the recording) • “play memos” (to play previously recorded memos) — during the playback you may press the voice com- mand button to stop playing memos. You pro- ceed by saying one of the following commands: – “repeat” (to repeat a memo) – “n...

  • Page 151

    Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect® voice “voice training” feature may be used. 1. Press the voice command button, say “system setup” and once you are in that menu then say “voice training.” this will train your...

  • Page 152

    Power seats — if equipped some models may be equipped with a power driver’s seat. The power seat switch is located on the outboard side of the seat near the floor. Use the switch to move the seat up, down, forward, rearward, or to tilt the seat. Warning! • adjusting a seat while driving may be dange...

  • Page 153

    Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting the seat up or down the height of the seats...

  • Page 154

    30 minutes of continuous operation. At that time, the display will change from hi to lo, indicating the change. When the low-level heating is selected, the system automatically turns the heater and the indicator light off after a maximum of 30 minutes of continuous operation. Note: once a heat setti...

  • Page 155

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 156

    Manual seat height adjustment — if equipped the driver’s seat height can be raised or lowered by using a lever, located on the outboard side of the seat. Pull upward on the lever to raise the seat height or push downward on the lever to lower the seat height. Manual lumbar — if equipped the lumbar a...

  • Page 157

    Driver’s seatback recline to adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired angle and release the lever. To return the seatback, lift the lever, lean forward and release the lever. Warning! Do not ride with the seatback reclined so that the sho...

  • Page 158

    Fold-flat front passenger seat to fold the front passenger seat, lift the recliner handle to the full upward position and push the seatback forward until it rests on the seat cushion. Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event ...

  • Page 159

    Warning! The head restraints for all occupants must be prop- erly adjusted prior to operating the vehicle or occu- pying a seat. Head restraints should never be ad- justed while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious in...

  • Page 160

    To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. For comfort the active head restraints can be tilted forward and backward. To tilt the head restrain...

  • Page 161

    Note: • the head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head re...

  • Page 162

    Warning! (continued) • active head restraints may be deployed if they are struck by an object such as a hand, foot or loose cargo. To avoid accidental deployment of the ac- tive head restraint ensure that all cargo is secured, as loose cargo could contact the active head re- straint during sudden st...

  • Page 163

    To raise the seatback, pull the strap forward and lift the seatback into its upright position. Warning! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers...

  • Page 164

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only with the vehicle is parked. To open and close the hood to open the hoo...

  • Page 165

    Lift the hood prop rod, clipped to the right side (left side facing hood) of the engine compartment to secure the hood in the open position. Place the hood prop at the location stamped into the inner hood surface. Hood safety latch location prop rod location 3 understanding the features of your vehi...

  • Page 166

    Caution! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open 8 in (20 cm) approximately and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. Warning! Be sure the hood is fully...

  • Page 167

    Headlights and parking lights turn the end of the multifunction lever to the first detent to turn on the parking lights. Turn the end of the lever to the second detent to turn on the headlights. Daytime running lights — if equipped the high beam lights will come on as daytime running lights (lower i...

  • Page 168

    Lights-on reminder if the headlights or parking lights are left on after the ignition is turned off, a chime will sound to alert the driver when the driver’s door is opened. Fog lights — if equipped the front fog light switch is on the multifunc- tion lever. To activate the front fog lights, turn on...

  • Page 169

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside l...

  • Page 170

    Flash-to-pass you can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will turn on the high beam headlights until the lever is released. Note: if the multifunction lever is held in the flash-to- pass position for more than 20 seconds, the high ...

  • Page 171

    Map/reading lights these lights are mounted between the sun visors above the rear view mirror. Each light is turned on by pressing the button. Press the button a second time to turn the light off. The lights also come on when a door is opened or the dimmer control is turned fully upward, past the se...

  • Page 172

    Windshield wipers and washers the windshield wiper/washer control lever is located on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. For information on the rear wiper/washer, refer to “rear window fea- tures” in “understand...

  • Page 173

    Caution! • turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • in cold weather, always turn off the wiper switch and allow the wipers to return to the “park” posi- tion be...

  • Page 174

    Intermittent wiper system use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Select the delay interval by turning the end of the lever. Rotate the end of the lever upward (clockwise) to decrease the delay time and downwar...

  • Page 175

    Mist feature push down on the control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. Note: the mist feature does not activate the washer pump; therefore, no washer fluid wil...

  • Page 176

    Push down on the lever to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Push the lever up to lock the steering column firmly in place. Warning! Do not adjust the steering column while driving. Adjusting the steering column wh...

  • Page 177

    The electronic speed control buttons are located on the right side of the steering wheel. Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic ...

  • Page 178

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To set a desired speed turn the elec...

  • Page 179

    To decrease speed while the electronic speed control is set, push the set (-) button. If the button is continually held in the set (-) position, the set speed will continue to decrease until the button is released. Release the button when the desired speed is reached, and the new set speed will be e...

  • Page 180

    Parkview® rear back up camera — if equipped your vehicle may be equipped with the parkview® rear back up camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into reverse. The image will be displayed on the navigation/multimedia ra...

  • Page 181

    Warning! Drivers must be careful when backing up even when using the parkview® rear back up camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your ...

  • Page 182

    4. Enable or disable the rear camera feature by selecting the “enable rear camera in reverse” soft-key. 5. Press the “save” soft-key. Turning parkview® on or off — without navigation/multimedia radio 1. Press the “menu” hard-key. 2. Select “system setup” soft-key. 3. Enable or disable the rear camer...

  • Page 183

    Note: homelink® is disabled when the vehicle secu- rity alarm is active. Before you begin programming homelink® be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recom...

  • Page 184

    Programming a rolling code for programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “learn” or “train” button located where the hanging antenna is attached to the garage door opener. It is not the button that is normally used to open...

  • Page 185

    1. Cycle the ignition to the on/run position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink® button you wish to pro- gram while keeping the homelink® indicator light in view. 3. Simultaneously press and hold both the homelink® button you want to program and the hand...

  • Page 186

    To program the remaining two homelink® buttons, repeat each step for each remaining button. Do not erase the channels. Reprogramming a single homelink® button to reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the on/run position. 2. Press and hold ...

  • Page 187

    • if the indicator light stays on constantly, program- ming is complete and the garage door/device should activate when the homelink® button is pressed. • to program the two remaining homelink® buttons, repeat each step for each remaining button. Do not erase the channels. Reprogramming a single hom...

  • Page 188

    2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink® button you wish to pro- gram while keeping the homelink® indicator light in view. 3. Continue to press and hold the homelink® button, while you press and release (“cycle”), your hand-held transmitter every two seconds u...

  • Page 189

    3. Without releasing the button proceed with “canadian/gate operator programming” step 2 and follow all remaining steps. Using homelink® to operate, press and release the programmed homelink® button. Activation will now occur for the programmed device (i.E., garage door opener, gate opera- tor, secu...

  • Page 190

    Warning! • your motorized door or gate will open and close while you are programming the universal trans- ceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” fea...

  • Page 191

    Power sunroof — if equipped the power sunroof switch is located on the overhead console. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle. Occupants, particularly unattended children, can become entrapped by the...

  • Page 192

    Opening sunroof — express press the switch rearward and release it within one-half second. The sunroof and sunshade will open automati- cally from any position. The sunroof and sunshade will open fully and stop automatically. This is called “express open”. During express open operation, any movement...

  • Page 193

    Venting sunroof — express press and release the vent button within one half second and the sunroof will open to the vent position. This is called “express vent”, and it will occur regardless of sunroof position. During express vent operation, any movement of the switch will stop the sunroof. Sunshad...

  • Page 194

    For vehicles equipped with the evic the power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is turned to the lock position. Opening either front door will cancel this feature. Electrical power outlets there is a standard 12 volt (13 amp) power outlet...

  • Page 195

    Note: to ensure proper operation a mopar® knob and element must be used. Caution! • do not exceed the maximum power of 160 watts (13 amps) at 12 volts. If the 160 watt (13 amp) power rating is exceeded the fuse protecting the system will need to be replaced. • power outlets are designed for accessor...

  • Page 196

    Warning! (continued) • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock and failure. Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in us...

  • Page 197

    Certain high-end video games, such as playstation3 and xbox360 will exceed this power limit, as will most power tools. The power inverter is designed with built-in overload protection. If the power rating of 150 watts is exceeded, the power inverter will automatically shut down. Once the electrical ...

  • Page 198

    Warning! (continued) • do not touch with wet hands. • close the lid when not in use. • if this outlet is mishandled, it may cause an electric shock and failure. Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc....

  • Page 199

    Cupholders your vehicle is equipped with four cupholders. There are two illuminated cupholders located in the front. There are two cupholders located in the back for the rear passengers. Front cupholders rear cupholders 3 understanding the features of your vehicle 197.

  • Page 200

    Storage glove compartment and storage bin located on the passenger side of the instrument panel are an upper storage bin and a lower glove compartment. To open the lower glove compartment, pull outward on the release handle. Storage bins 1 — upper storage bin 2 — lower glove compartment glove compar...

  • Page 201

    Door storage the interior door panels are equipped with lower storage areas. Console features the floor console contains both an upper and lower storage compartment. Front door storage rear door storage 3 understanding the features of your vehicle 199.

  • Page 202

    To open the upper storage compartment, push inward on the upper handle to unlatch the upper lid and lift the lid open. To open the lower storage compartment, lift upward on the lower handle to unlatch the lower storage compart- ment and lift the lid open. Warning! Do not operate this vehicle with a ...

  • Page 203

    Warning! (continued) should be stowed while driving. Use of these devices while driving can cause an accident due to distrac- tion, resulting in death or injury. Cargo area features cargo light/removable self-recharging flashlight the dual-function light is mounted in the headliner above the cargo a...

  • Page 204

    To operate the flashlight, press the switch once for high, twice for low, and a third time to return to off. Cargo cover the cargo area trim panels include two notches for mounting the available tonneau cover that accommo- dates the reclining rear seat. To install the cargo cover, insert either end ...

  • Page 205

    Using the handle, pull the cover toward you and guide the rear cover posts into the guides located on both sides of the rear trim panel. Warning! In a collision a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store...

  • Page 206

    Removable load floor the cargo area load floor is removable and can be washed with mild soap and water. Cargo tie-down loops there are four tie-downs (d-rings) installed in the cargo area for securing cargo. Removable load floor cargo area tie-downs 204 understanding the features of your vehicle.

  • Page 207

    Warning! • cargo tie-down loops are not safe anchors for a child seat tether strap. In a sudden stop or collision a loop could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • the weight and position of cargo a...

  • Page 208

    Fold down speakers — if equipped when the liftgate is open, the speakers can swing down off the trim panel to face rearward, for tailgating and other activities. Rear window features rear window wiper/washer the rear wiper/washer is controlled by a rotary switch located on the center portion of the ...

  • Page 209

    Rotate the center portion of the lever upward to the first detent position for rear wiper operation. Note: the rear wiper operates in an intermittent mode only. Rotate the center portion of the lever past the first detent to activate the rear washer. The washer pump and the wiper will continue to op...

  • Page 210

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 211

    Approximately eight turns, then move the crossbar to the desired position, keeping the crossbars perpendicular to the luggage rack side rails. Once the crossbar is in one of the seven detent positions, retighten the thumb screws to lock the crossbar into position. Note: • to help control wind noise ...

  • Page 212

    Caution! (continued) • long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle. • travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof ra...

  • Page 213: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .214 䡵 instrument cluster . . . . . . . . . . . . . . . . .215 䡵 instrument cluster descriptions . . . . .216 䡵 mini-trip computer — if equipped . . . . .230 ▫ control buttons . . . . . . . . . . . . . . . . ....

  • Page 214

    ▫ operating instructions - radio mode . . . . . . . .243 ▫ operation instructions - (disc mode for cd and mp3/wma audio play, dvd-video) . . .252 ▫ list button (disc mode for mp3/wma play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .257 ▫ info button (disc mode for mp3/wma play) . . ....

  • Page 215

    ▫ connecting the ipod® or external usb device . . . . . . . . . . . . . . . . . . . . . . . . . . . . .291 ▫ using this feature. . . . . . . . . . . . . . . . . . . . .292 ▫ controlling the ipod® or external usb device using radio buttons . . . . . . . . . . . . . . . . . . .292 ▫ play mode . . . . ...

  • Page 216

    Instrument panel features 1 — air outlet 5 — storage bin 9 — heated seat switch – if equipped 2 — demisters 6 — glove compartment 10 — hazard warning flasher 3 — instrument cluster 7 — climate controls 11 — esc off switch – if equipped 4 — radio 8 — power outlet 12 — heated seat switch – if equipped...

  • Page 217

    Instrument cluster 4 understanding your instrument panel 215.

  • Page 218

    Instrument cluster descriptions 1. Fuel gauge / fuel door reminder when the ignition switch is in the on/run position, the pointer will show the level of fuel remaining in the fuel tank. The fuel pump symbol points to the side of the vehicle where the fuel door is located. 2. Charging system light t...

  • Page 219

    On briefly as a bulb check. If the light does not come on during starting, have the system checked by an autho- rized dealer. 4. Oil pressure warning light this light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while drivi...

  • Page 220

    If the vehicle is driven more than 1 mile (1.6 km) with either turn signal on, a continuous chime will sound to alert you to turn the signals off. If either indicator flashes at a rapid rate, check for a defective outside light bulb. 9. High beam indicator this indicator shows that the high beam hea...

  • Page 221

    12. Tachometer the white area of the scale shows the permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 13. Engine temperature warning light this light warns of an overheated engine condi- tio...

  • Page 222

    Booster, the abs pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by ...

  • Page 223

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 15. Transmission temperature warning light this light indicates that the t...

  • Page 224

    The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. Caution! Driving with a hot engine cooling system could damage your vehicle. If ...

  • Page 225

    20. Shift lever indicator the shift lever indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. Note: you must apply the brakes before shifting from park. 21. Odometer/trip odometer reset button press this button to change the display...

  • Page 226

    Maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the tpms low tire pressure telltale. Your vehicle has also been equipped with a tpms malfunction indicator to indicate when the system is not operating properly. The tpms malfunction indicato...

  • Page 227

    Note: u.S. Federal regulations require that upon trans- fer of vehicle ownership, the seller certify to the pur- chaser the correct mileage that the vehicle has been driven. If your odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was ...

  • Page 228

    Gascap if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “gascap” message will display in the odometer display area. Tighten the fuel filler cap properly and press the trip odometer button to turn off the message. If the problem contin...

  • Page 229

    Temporarily, press and release the trip odometer button on the instrument cluster. To reset the oil change indica- tor system (after performing the scheduled maintenance), refer to the following procedure: 1. Turn the ignition switch to the on/run position (do not start the engine). 2. Fully depress...

  • Page 230

    Caution! (continued) converter damage and power loss will soon occur. Immediate service is required. Warning! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable...

  • Page 231

    (kilometers) at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected. Note: • the “esc off indicator light” and the “esc activation/malfunction indicator light” come on momentarily each time the ignition switch is turned to ...

  • Page 232

    30. Hill descent indicator — if equipped the symbol illuminates (is armed) when the 4wd lock switch is activated and the trans- mission range indicator is in low or reverse position (off-road mode). Mini-trip computer — if equipped the mini-trip computer is located in the instrument cluster and feat...

  • Page 233

    Reset button to reset the display shown, turn the ignition switch to the on position, then press and hold the reset button located on the steering wheel. The following displays can be reset or changed: • trip a • trip b trip odometer (odo) this display shows the distance traveled since the last rese...

  • Page 234

    Electronic vehicle information center (evic) — if equipped the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following: • system status • units • vehicle information warning message displays • ...

  • Page 235

    The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: menu button press and release the menu button to scroll through the main menus (fuel economy, warn- ings, timer, units, system, personal settings) or to exit sub-menus. Compass button ...

  • Page 236

    Down button press and release the down button to scroll downward through the sub-menus. When the appropriate conditions exist, the evic displays the following messages: • turn signal on (with a continuous warning chime after 1 mile (1.6 km) of distance travelled) • left front turn signal lamp out (w...

  • Page 237

    • remote start aborted — fuel low • remote start aborted — system fault • key in ignition • low tire • low tire pressure display for premium tpm system • service tpm system engine oil change indicator system — if equipped oil change required your vehicle is equipped with an engine oil change indicat...

  • Page 238

    Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary repeat this procedure. Evic functions • compass/temperature/audio • average fuel economy • distance to empty (dte) • units in • elapsed time • tire pressure monitor (tpm...

  • Page 239

    History information will be erased, and the averaging will continue from the last fuel reading before the reset. Distance to empty (dte) shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantan...

  • Page 240

    Reset all digits will change to zeros and time will start incrementing again if the ignition switch is in run or start. Display units of measure in to make your selection, press and release the select button until “english” or “metric” appears. Personal settings (customer-programmable features) this...

  • Page 241

    Auto unlock on exit when on is selected, all the vehicle’s doors will unlock when the driver’s door is opened, if the vehicle is stopped (manual transmission) or the vehicle is stopped and the transmission is in the park or neutral position (automatic transmission). Press and hold the select button ...

  • Page 242

    When exiting the vehicle. Press and hold the select button when in this display until 0, 30, 60, or 90 appears to make your selection. Key off power delay when this feature is selected the power window switches, radio, uconnect® phone, power sunroof, and power outlets will remain active for up to 10...

  • Page 243

    Automatic compass calibration this compass is self-calibrating, which eliminates the need to set the compass manually. When the vehicle is new, the compass may appear erratic and the evic will display “cal” until the compass is calibrated. You may also calibrate the compass by completing one or more...

  • Page 244

    Compass variance compass variance is the difference between magnetic north and geographic north. To compensate for the differences, the variance should be set for the zone where the vehicle is driven, per the zone map. Once properly set, the compass will automatically compensate for the differences ...

  • Page 245

    1. Turn the ignition switch on. 2. Press and hold the compass button for approxi- mately two seconds. 3. Press the down button until “compass variance” message and the last variance zone number displays in the evic. 4. Press and release the select button until the proper variance zone is selected ac...

  • Page 246

    Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Press the on/volume control knob a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the ...

  • Page 247

    Phone button uconnect® phone — if equipped press this button to operate the uconnect® phone feature (if equipped). Refer to “uconnect® phone” for further details. If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with uconnect phone” message will ...

  • Page 248

    Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in am, fm or satellite (if equipped) frequencies. Tune control turn the rotary tune/scroll control knob clockwise to increase or counter...

  • Page 249

    Or turning the tune/scroll control knob within five seconds will allow the program format type to be se- lected. Many radio stations do not currently broadcast music type information. Toggle the music type button to select the following format types: program type 16-digit character display no progra...

  • Page 250

    Program type 16-digit character display sports sports talk talk top 40 top 40 weather weather by pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in...

  • Page 251

    • dvd play options - selecting the dvd play options will display the following: • subtitle – repeatedly pressing select will switch subtitles to different subtitle languages that are avail- able on the disc (if equipped). • audio stream – repeatedly pressing select will switch to different audio lan...

  • Page 252

    Menu language — if equipped selecting this item will allow the user to choose the default startup dvd menu language (effective only if language supported by disc). If you want to select a language not listed, then scroll down and select ⬙ other. ⬙ enter the four-digit country code using the tune/ sc...

  • Page 253

    Aspect ratio — if equipped selecting this item allows you to choose between wide screen, pan scan, and letter box. Autoplay — if equipped when this is set to on and a dvd video is inserted, it will bypass the dvd menu screen and automatically play the movie. In some rare cases, the dvd player may no...

  • Page 254

    Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to pushbutton memory {12 am, 12 fm, and 12 satellite (if equipped) stations}. Disc button pressing the disc button will allow you to switch from ...

  • Page 255

    Prompt when to insert disc. After the radio displays ⬙ insert disc, ⬙ insert the cd into the player. Radio display will show ⬙ loading disc ⬙ when the disc is loading and “reading disc” when the radio is reading the disc. Caution! This cd player will accept 4–3/4 in (12 cm) discs only. The use of ot...

  • Page 256

    Time button (cd mode) press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff (cd mode) press and hold ff (fast forward) and the cd player will begin to fast forward until ff is released, or rw or another cd button is pressed. The rw (re...

  • Page 257

    • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙ . ⬙ and a three- character extension) • level 2: 31 (including a separator ⬙ . ⬙ and a three- character extension) multisession disc formats are supported by the radio. Multisession discs may contain combinat...

  • Page 258

    Mpeg specification sampling frequency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48 wma specification sampling frequency (khz) bit rate (kbps) wma 44.1 and 48 48,...

  • Page 259

    • number of files and folders - loading times will increase with more files and folders to increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. List button (disc...

  • Page 260

    Pressing the aux button will change the mode to auxil- iary device if the aux jack is connected. Note: the aux device must be turned on and the device’s volume set to the proper level. If the aux audio is not loud enough, turn the device’s volume up. If the aux audio sounds distorted, turn the devic...

  • Page 261

    Operating instructions - video entertainment system (ves™) (if equipped) refer to “video entertainment system (ves™)” for fur- ther details. Dolby® manufactured under license from dolby® laboratories. Dolby® and the double-d symbol are trademarks of dolby® laboratories. Macrovision this product inco...

  • Page 262

    Radio system in your vehicle. Sirius will supply a wel- come kit that contains general information, including how to setup your on-line listening account. For further information, call the toll-free number 888-539-7474, or visit the sirius web site at www.Sirius.Com, or at www.Siriuscanada.Ca for ca...

  • Page 263

    Bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or...

  • Page 264

    Info button pressing the info button will cycle the display informa- tion between artist, song title, and composer (if avail- able). Also, pressing and holding the info button for an additional three seconds will make the radio display the song title all of the time (press and hold again to return t...

  • Page 265

    Setup button pressing the setup button allows you to select the following items: • display sirius id number — press the audio/ select button to display the sirius id number. This number is used to activate, deactivate, or change the sirius subscription. Set/rnd button — to set the pushbutton memory ...

  • Page 266

    Operating instructions (voice command system) — if equipped refer to “voice command” for further details. Operating instructions (uconnect® phone) — if equipped refer to “uconnect® phone” for further details. Uconnect® 130 operating instructions — radio mode note: the ignition switch must be in the ...

  • Page 267

    Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 degrees) in either direction, without stopping. Turning the ...

  • Page 268

    5. To exit, press any button/knob, or wait five seconds. Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either am or fm frequencies. Tune control turn the rotary tune/scroll contro...

  • Page 269

    Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Am/fm button press the buttons to select either am or fm mode. Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, press the set/rnd button...

  • Page 270

    Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks and m...

  • Page 271

    Caution! (continued) • dual-media disc types (one side is a dvd, the other side is a cd) should not be used, and they can cause damage to the player. Eject button - ejecting a cd press the eject button to eject the cd. If you have ejected a disc and have not removed it within 10 seconds, it will be ...

  • Page 272

    Am/fm button press the button to select either am or fm mode. Set/rnd button (random play button) press this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right seek bu...

  • Page 273

    Display the file name and folder name, and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this dis- play.) • maximum number of characters in file/folder names: • level 1: 12 (includin...

  • Page 274

    Mpeg specification sampling frequency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 id3 tag information for artist, song title, and alb...

  • Page 275

    To increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the...

  • Page 276

    Uconnect® 130 with satellite radio operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn of...

  • Page 277

    Another selection. Holding either button will bypass stations without stopping, until you release it. Voice command system (radio) — if equipped refer to “voice command” in “understanding the fea- tures if your vehicle.” voice command button uconnect® phone — if equipped press this button to operate...

  • Page 278

    3. After adjusting the hours, press the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll con- trol knob to save time change. 5. To exit, press any button/knob or wait ...

  • Page 279

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 280

    Program type 16-digit character display classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc progra...

  • Page 281

    If a preset button is activated while in the music type (program type) mode, the music type mode will be exited and the radio will tune to the preset station. Setup button pressing the setup button allows you to select between the following items: • set clock — pressing the select button will allow ...

  • Page 282

    Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to pushbutton memory (12 am and 12 fm stations). Disc/aux button pressing the disc/aux button will allow you to switch from am/fm modes to disc/a...

  • Page 283

    Caution! • this cd player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. • do not use adhesive labels. These labels can peel away and jam the player mechanism. • the uconnect® 130 is a single cd player. Do not attempt to insert a second cd i...

  • Page 284

    Rw/ff press and hold ff (fast forward) and the cd player will begin to fast forward until ff is released or rw or another cd button is pressed. The rw (reverse) button works in a similar manner. Am/fm button press the button to select either am or fm mode. Set/rnd button (random play button) press t...

  • Page 285

    The radio uses the following limits for file systems: • maximum number of folder levels: 8 • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file ...

  • Page 286

    Use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bit rates. Mpeg specification sampling frequency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48...

  • Page 287

    To increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. List button (cd mode for mp3 play) pressing the list button will bring up a list of all folders on the di...

  • Page 288

    Note: the aux device must be turned on and the device’s volume set to the proper level. If the aux audio is not loud enough, turn the device’s volume up. If the aux audio sounds distorted, turn the device’s volume down. Time button (auxiliary mode) press this button to change the display to time of ...

  • Page 289

    Electronic serial number/sirius identification number (esn/sid) please have the following information available when calling: 1. The electronic serial number/sirius identification number (esn/sid). 2. Your vehicle identification number. To access the esn/sid, refer to the following steps: esn/sid ac...

  • Page 290

    • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or along tall buildings can cause intermittent reception. • placing objects over or too close to the antenna can cause signal blockage. Operating instructions - uconnect® (satellite) mode not...

  • Page 291

    Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decrease the channel. Music type button pressing thi...

  • Page 292

    Select the button (1-6) you wish to lock onto this channel and press and release that button. If a button is not selected within five seconds after pressing the set but- ton, the channel will continue to play but will not be stored into pushbutton memory. You may add a second channel to each pushbut...

  • Page 293

    Note: • if the radio has a usb port, refer to the appropriate uconnect® multimedia radio user’s manual for ipod® or external usb device support capability. • connecting an ipod® or consumer electronic audio device to the aux port located in the radio faceplate, plays media, but does not use the ipod...

  • Page 294

    Note: if the audio device battery is completely dis- charged, it may not communicate with the ipod®/usb/ mp3 control system until a minimum charge is attained. Leaving the audio device connected to the ipod®/usb/ mp3 control system may charge it to the required level. Using this feature by using an ...

  • Page 295

    • turning it clockwise (forward) by one click, while playing a track, skips to the next track or press the vr button and say ⬙ next track. ⬙ • turning it counterclockwise (backward) by one click, will jump to the previous track in the list or press the vr button and say ⬙ previous track. ⬙ • jump ba...

  • Page 296

    Scan button again. During scan mode, pressing the seek and seek >> buttons will select the previous and next tracks. • rnd button (available on sales code res radio only): pressing this button toggles between shuffle on and shuffle off modes for the ipod® or external usb device, or press the vr butt...

  • Page 297

    • preset 2 – artists • preset 3 – albums • preset 4 – genres • preset 5 – audiobooks • preset 6 – podcasts • pressing a preset button will display the current list on the top line and the first item in that list on the second line. • to exit list mode without selecting a track, press the same preset...

  • Page 298

    Warning! Do not plug in or remove the ipod® or external usb device while driving. Failure to follow this warning could result in an accident. Bluetooth streaming audio (btsa) music can be streamed from your cellular phone to the uconnect® phone system. Controlling btsa using radio buttons to enter b...

  • Page 299

    Previous track use the seek down button, or press the vr button on the radio and say “previous track,” to jump to the previous music track on your cellular phone. Browse browsing is not available on a bluetooth streaming audio (btsa) device. Only the current song that is playing will display info. S...

  • Page 300

    Pressing the center button will make the radio switch between the various modes available (am/fm/sat/ cd/hdd/aux/ves, etc.). The left-hand control is a rocker-type switch with a pushbutton in the center. The function of the left-hand control is different depending on which mode you are in. The follo...

  • Page 301

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 302

    Climate controls the air conditioning and heating system is designed to make you comfortable in all types of weather. Manual heating and air conditioning the manual temperature controls consist of a series of outer rotary dials and inner push knobs. Manual temperature control 300 understanding your ...

  • Page 303

    Blower control rotate this control to regulate the amount of air forced through the ven- tilation system in any mode. The blower speed increases as you move the control to the right from the “o” (off) position. There are seven blower speeds. Note: for vehicles equipped with remote start, the climate...

  • Page 304

    Mode control (air direction) rotate this control to choose from sev- eral patterns of air distribution. You can select either a primary mode as identified by the symbols on the con- trol, or a blend of two of these modes. The closer the setting is to a particular symbol, the more air distribution yo...

  • Page 305

    • defrost air is directed through the windshield and side window demist outlets. Use this mode with maxi- mum blower and temperature settings for best wind- shield and side window defrosting. Note: • the air conditioning compressor operates in mix, defrost, or a blend of these modes, even if the air...

  • Page 306

    • the a/c will engage automatically to prevent fogging when the recirculation button is pressed and the mode control is set to panel or panel / floor. • the a/c can be deselected manually without disturb- ing the mode control selection. • when the ignition switch is turned to the lock position, the ...

  • Page 307

    Automatic operation operation of the system is quite simple. 1. Turn the mode control knob (on the right) and the blower control knob (on the left) to auto. Note: the auto position performs best for front seat occupants only. 2. Dial in the temperature you would like the system to maintain by ro- ta...

  • Page 308

    The recommended setting for maximum comfort for the average person is 72°f (22°c); however, this may vary. Note: • the temperature setting can be adjusted at anytime without affecting automatic operation. • pressing the air conditioning control button while in auto mode will cause the led in the con...

  • Page 309

    4 understanding your instrument panel 307.

  • Page 310

    The operator can override the auto mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions. • panel air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. Note: the center ...

  • Page 311

    • air conditioner control press this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the mode control dial. Press this but- ton a second time to turn off the air conditionin...

  • Page 312

    • most of the time, when in automatic operation, you can temporarily put the system into recirculation mode by pressing the recirculation button. However, under cer- tain conditions, while in automatic mode, the system is blowing air out the defrost vents. When these conditions are present, and the ...

  • Page 313

    Adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Window fogging interior fogging on the windshield can be quickly removed by turning the mode selector to defrost. The defrost/floor mode can be used to maintain a clear windshield and provi...

  • Page 314

    Control setting suggestions for various weather conditions 312 understanding your instrument panel.

  • Page 315: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .318 ▫ manual transmission – if equipped . . . . . . . .318 ▫ automatic transmission – if equipped . . . . . .319 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .319 ▫ extreme cold weather (below –20°f ...

  • Page 316

    䡵 autostick® . . . . . . . . . . . . . . . . . . . . . . . . .339 ▫ autostick® (six-speed automatic transmission) – if equipped . . . . . . . . . . . . .339 ▫ autostick® (cvt) – if equipped . . . . . . . .341 䡵 four-wheel drive operation — if equipped . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 317

    ▫ esc activation/malfunction indicator light and esc off indicator light . . . . . . . . . . . . . . . .371 䡵 tire safety information . . . . . . . . . . . . .373 ▫ tire markings . . . . . . . . . . . . . . . . . . . . . . . .373 ▫ tire identification number (tin). . . . . . . . . . .376 ▫ tire term...

  • Page 318

    䡵 tire pressure monitoring system (tpms) . . . . . . . . . . . . . . . . . . . . . . .396 ▫ base system . . . . . . . . . . . . . . . . . . . . . . . . .399 ▫ premium system – if equipped. . . . . . . . . . . .401 ▫ general information . . . . . . . . . . . . . . . . . . .406 䡵 fuel requirements . ....

  • Page 319

    ▫ towing requirements . . . . . . . . . . . . . . . . . .420 ▫ towing tips . . . . . . . . . . . . . . . . . . . . . . . . .426 䡵 recreational towing (behind motorhome, etc.) . . . . . . . . . . . . . . . . . . .428 ▫ towing this vehicle behind another vehicle . .428 5 starting and operating 317.

  • Page 320

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park, and re- move the key fob from the ignition. When leaving the ...

  • Page 321

    Automatic transmission – if equipped the shift lever must be in the park or neutral position before you can start the engine. Depress the brake pedal before shifting to any driving gear. Note: you must press the brake pedal before shifting out of park. Tip start do not press the accelerator. Turn th...

  • Page 322

    Warning! (continued) another vehicle. This type of start can be dangerous if done improperly, so follow the procedure carefully. Refer to “jump starting” in “what to do in emer- gencies” for further information. Extreme cold weather (below –20°f or −29°c) to ensure reliable starting at these tempera...

  • Page 323

    Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. The engine block heater must be plugged in at least one hour to have an...

  • Page 324

    Fully press the clutch pedal before you shift gears. As you release the clutch pedal, lightly press the accelerator pedal. Use each gear in numerical order, do not skip a gear. Be sure the transmission is in first gear, (not third), when starting from a standing position. Damage to the clutch can re...

  • Page 325

    For most city driving, you will find it easier to use only the lower gears. For steady highway driving with light accelerations, fifth gear is recommended. Never drive with your foot resting on the clutch pedal, and never try to hold the vehicle on a hill with the clutch pedal partially engaged. Thi...

  • Page 326

    Downshifting proper downshifting will improve fuel economy and prolong engine life. Caution! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released. Damage...

  • Page 327

    Note: you must press and hold the brake pedal while shifting out of park. Warning! • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. • before exiting a vehicle, always apply the parking bra...

  • Page 328

    Key ignition park interlock this vehicle is equipped with a key ignition park inter- lock which requires the transmission to be in park before the ignition switch can be turned to the lock position. The key can only be removed from the ignition when the ignition is in the lock position, and once rem...

  • Page 329

    Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears. The transmission shift lever has only park, reverse, neutral, and drive shift positions. Manual shifts can be ma...

  • Page 330

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • your vehicle could move and injure you and others if it is not completely in park. Check by trying to mo...

  • Page 331

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and r...

  • Page 332

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the off posi- tion to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ran...

  • Page 333

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 334

    If the transmission temperature exceeds normal operat- ing limits, the transmission controller will modify the transmission shift schedule and expand the range of torque converter clutch engagement. This is done to prevent transmission damage due to overheating. If the transmission becomes extremely...

  • Page 335

    6. Shift into the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic...

  • Page 336

    Note: engagement of the torque converter clutch is inhibited at very cold temperatures. Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into overdrive when cold. This is normal. The torque converter clutch will fu...

  • Page 337

    Gear ranges do not race the engine when shifting from park or neutral into another gear range. Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park (p) this range supplements the parki...

  • Page 338

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 339

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the shift lever. • do not leave the key fob in or near the ...

  • Page 340

    • look at the transmission gear position display and verify that it indicates the park position. • with brake pedal released, verify that the shift lever will not move out of park. Reverse (r) this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a comp...

  • Page 341

    Drive (d) this range should be used for most city and highway driving. It provides the best fuel economy. The drive position provides optimum driving characteristics under all normal operating conditions. When frequent transmission shifting occurs (such as when operating the vehicle under heavy load...

  • Page 342

    Improve overall vehicle performance. This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations. Operation when the shift lever is in the drive position, the transmission will operate automati...

  • Page 343

    • if a requested downshift would cause the engine to overspeed, that shift will not occur. • avoid using speed control when autostick® is en- gaged. • transmission shifting will be more noticeable when autostick® is engaged. • the system may revert to automatic shift mode if a fault or overheat cond...

  • Page 344

    Operation note: autostick® is not available until the cvt warms up in cold weather. When the shift lever is in the drive position, autostick® is activated by moving the shift lever side-to-side. Mov- ing the shift lever to the right (+) will activate autostick® and shift up to the next higher manual...

  • Page 345

    To disengage autostick® mode, hold the shift lever to the right (+) until “d” is once again displayed in the instru- ment cluster. You can shift in or out of the autostick® mode at any time without taking your foot off the accelerator pedal. Warning! Do not downshift for additional engine braking on...

  • Page 346

    Cluster. This can be done on the fly, at any vehicle speed. To deactivate, simply pull on the switch one more time. The “4wd indicator light” will then go out. Note: refer to “electronic brake control system/ electronic stability control (esc)” in “starting and op- erating” for further information. ...

  • Page 347

    Safe and what is not. When on a trail, you should always be looking ahead for surface obstacles and changes in terrain. The key is to plan your future driving route while remembering what you are currently driving over. Caution! Never park your vehicle over dry grass or other combustible materials. ...

  • Page 348

    Driving in snow, mud and sand there is a drastic reduction in traction when driving in snow, mud or sand. The vehicle will be less responsive to steering, acceleration and braking inputs. Therefore, you should accelerate slowly, leave greater stopping distances and avoid abrupt vehicle maneuvers. Yo...

  • Page 349

    Sand soft sand is very difficult to travel through with full tire pressure. When crossing soft sandy spots in a trail maintain your vehicle’s momentum and do not stop. The key to driving in soft sand is using the appropriate tire pressure, accelerating slowly, avoiding abrupt maneu- vers and maintai...

  • Page 350

    Before climbing a steep hill as you approach a hill consider its grade or steepness. Determine if it is too steep. Look to see what the traction is on the hill side trail. Is the trail straight up and down? What is on top and the other side? Are there ruts, rocks, branches or other obstacles on the ...

  • Page 351

    Driving down hill before driving down a steep hill you need to determine if it is too steep for a safe descent. What is the surface traction? Is the grade too steep to maintain a slow controlled descent? Are there obstacles? Is it a straight descent? Is there plenty of distance at the base of the hi...

  • Page 352

    And hill descent braking to control the descent and apply your brakes if necessary, but do not allow the tires to lock. Warning! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling th...

  • Page 353

    Caution! Water ingestion into the transaxle, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water. Water can cause permanent damage to engine, driveline or other vehicle components and your brakes will be less effective once wet and/or muddy. Before ...

  • Page 354

    Caution! Muddy waters can reduce the cooling system effec- tiveness by depositing debris onto the radiator. After driving off-road off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road, it is always a good idea to check for damage. That way you can ...

  • Page 355

    Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent a collision. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. • if y...

  • Page 356

    • upon initial start-up in cold weather, the power steer- ing pump may make noise for a short amount of time. This is due to the cold, thick fluid in the steering system. This noise should be considered normal, and it does not in any way damage the steering system. Warning! Continued operation with ...

  • Page 357

    Warning! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill. Use only manufacturer’s recommended power steering fluid. If necessary, add fluid to restore to the proper indicated leve...

  • Page 358

    When the parking brake is applied with the ignition switch in the on position, the “brake warning light” in the instrument cluster will illuminate. Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is de...

  • Page 359

    Warning! (continued) • do not leave the key fob in or near the vehicle, or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle. • be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a ...

  • Page 360

    Warning! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency...

  • Page 361

    Warning! • pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • the abs cannot prevent the natural laws of phys- ics from acting on the ve...

  • Page 362

    If the “abs warning light” is on, the brake system should be serviced as soon as possible to restore the benefits of anti-lock brakes. If the “abs warning light” does not come on when the ignition switch is turned to the on position, have the bulb repaired as soon as possible. If both the “brake war...

  • Page 363

    Warning! The anti-lock brake system (abs) contains sophis- ticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This in- terference can cause possible loss of anti-lock brak- ing capability. Installation of s...

  • Page 364

    Warning! • pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • the abs cannot prevent the natural laws of phys- ics from acting on the ve...

  • Page 365

    System detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce braking distances. The bas complements the anti-lock brake system (abs). Applying the brakes very quickly results in the best bas ...

  • Page 366

    Engine power to lessen the chance that wheel lift will occur. Erm will only intervene during very severe or evasive driving maneuvers. Erm can only reduce the chance of wheel lift occurring during severe or evasive driving maneuvers. It can not prevent wheel lift due to other factors such as road co...

  • Page 367

    Or reverse. Refer to “safe off-road driving” in “start- ing and operating” for further information. When hdc is properly enabled, the “hill decent control light” in the instrument cluster will be illuminated. Hdc has the capability to sense terrain and will only activate when the vehicle is descendi...

  • Page 368

    Hill start assist (hsa) the hsa system is designed to assist the driver when starting a vehicle from a stop on a hill. Hsa will maintain the level of brake pressure the driver applied for a short period of time after the driver takes their foot off of the brake pedal. If the driver does not apply th...

  • Page 369

    “electronic vehicle information center (evic)” in “un- derstanding your instrument panel” for further informa- tion. For vehicles not equipped with the evic, perform the following steps: note: you must complete steps 1 through 8 within 90 seconds. 1. Center the steering wheel (front wheels pointing ...

  • Page 370

    Electronic stability control (esc) this system enhances directional control and stability of the vehicle under various driving conditions. Esc cor- rects for over-steering or under-steering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the over-steering or ...

  • Page 371

    Esc operating modes the esc system has three available operating modes for four–wheel drive equipped vehicles and two available operating modes for two–wheel drive equipped vehicles. Full on (four-wheel drive models) or on (two-wheel drive models) this is the normal operating mode for esc. Whenever ...

  • Page 372

    Warning! When in “partial off” mode, the tcs functionality of esc (except for the limited slip feature described in the tcs section) has been disabled and the “esc off indicator light” will be illuminated. When in “par- tial off” mode, the engine power reduction of tcs is disabled, and the enhanced ...

  • Page 373

    Note: the “esc off” message will display and an audible chime will sound when the shift lever is placed into the park position from any other position, and then moved out of the park position. This will occur even if the message was previously cleared. Warning! With the esc in the ⴖ full off ⴖ mode,...

  • Page 374

    Flashes when tcs is active. If the “esc activation/ malfunction indicator light” begins to flash during ac- celeration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. Note: • the “esc off indicator light...

  • Page 375

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 376

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it beg...

  • Page 377

    Example: r = construction code — ⬙ r ⬙ means radial construction — ⬙ d ⬙ means diagonal or bias construction 15 = rim diameter in inches (in) service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of ...

  • Page 378

    Example: load identification: ⴖ ....Blank.... ⴖ = absence of any text on the sidewall of the tire indicates a standard load (sl) tire extra load (xl) = extra load (or reinforced) tire light load (ll) = light load tire c, d, e, f, g = load range associated with the maximum load a tire can carry at a ...

  • Page 379

    Example: dot ma l9 abcd 0301 dot = department of transportation — this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 380

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 381

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. B-pillar location for tire and loading information placard 5 starting and operating 379.

  • Page 382

    Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the ve- hicle. 2) total weight your vehicle can carry. 3) tire size designed for your vehicle. 4) told tire inflation pressures for the front, rear, and spare tires...

  • Page 383

    Note: under a maximum loaded vehicle condition, gross axle weight ratings (gawrs) for the front and rear axles must not be exceeded. For further information on gawrs, vehicle loading, and trailer towing, refer to “vehicle loading” in this section. To determine the maximum loading conditions of your ...

  • Page 384

    6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Note: • the following table shows examples on how to calcu- late total load, cargo...

  • Page 385

    5 starting and operating 383.

  • Page 386

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 387

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear pat- terns...

  • Page 388

    Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”. Cold tire infl...

  • Page 389

    Loading may be required for high-speed vehicle opera- tion. Refer to your authorized tire or original equipment vehicle dealer for recommended safe operating speeds, loading and cold tire inflation pressures. Warning! High speed driving with your vehicle under maxi- mum load is dangerous. The added ...

  • Page 390

    Consult an authorized tire dealer for tire repairs and additional information. Damaged run flat tires, or run flat tires that have experienced a loss of pressure should be replaced imme- diately with another run flat tire of identical size and service description (load index and speed code). All sea...

  • Page 391

    Original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states pro- hibit s...

  • Page 392

    Do not install more than one compact spare tire and wheel on the vehicle at any given time. Warning! Compact spares are for temporary emergency use only. With these spares, do not drive more than 50 mph (80 km/h). Temporary use spares have limited tread life. When the tread is worn to the tread wear...

  • Page 393

    Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressures listed on your tire and loading inf...

  • Page 394

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is wo...

  • Page 395

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with...

  • Page 396

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 397

    Caution! Damage to the vehicle may result if tire chains are used. Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can...

  • Page 398

    Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold placard pressure. The tire pressure will vary with temperature by about 1 psi (7.0 kpa) for every 12°f (6.5°c). This means that when the ...

  • Page 399

    The tpms will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold placard pressure. Once the low tire pressure warn- ing (tire pressure monitoring telltale light) illuminates, you must inc...

  • Page 400

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, ...

  • Page 401

    • seasonal temperature changes will affect tire pressure, and the tpms will monitor the actual tire pressure in the tire. Base system this is the tpms warning indicator located in the instrument cluster. The tpms uses wireless technology with wheel rim mounted electronic sensors to monitor tire pres...

  • Page 402

    Check tpms warnings the tire pressure monitoring telltale light will flash on and off for 75 seconds and remain on solid when a system fault is detected. The system fault will also sound a chime. If the ignition key is cycled, this sequence will repeat providing the system fault still exists. The ti...

  • Page 403

    4. For each subsequent ignition key cycle, a chime will sound and the tire pressure monitoring telltale light will flash on and off for 75 seconds and then remain on solid. 5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare tire, the tp...

  • Page 404

    • various tire pressure monitoring system messages, which display in the electronic vehicle information center (evic) • tire pressure monitoring telltale light tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illumi- nate in the instrument cluster and a...

  • Page 405

    Flashing, and the tire pressure monitoring light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this infor- mation. Service tpms message the tire pressure monitoring telltale light will fl...

  • Page 406

    If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the tire pressure monitoring telltale light will no longer flash, the ⬙ service tpm system ⬙ text message will not be present, and a pressure value will be display...

  • Page 407

    2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warn- ing limit, upon the next ignition key cycle, a chime will sound and the tire pressure monitoring telltale light will still turn on due to the low tire. The “low tire” text message and th...

  • Page 408

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 409

    Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the world- wide fuel charter, wwfc) which define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recom- mends the use of gasolines...

  • Page 410

    E-85 usage in non-flex fuel vehicles non-flex fuel vehicle (ffv) is compatible with gasoline containing 10% ethanol (e10). Gasoline with higher etha- nol content may void the new vehicle limited warranty. If a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all o...

  • Page 411

    Materials added to fuel all gasoline sold in the united states is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefore, you should not have to add anything to the f...

  • Page 412

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 413

    After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s surface. Caution! • damage to the fuel system or emission control system could result from using an improper fuel tank filler c...

  • Page 414

    Warning! (continued) • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the mil to turn on. • a fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas...

  • Page 415

    Vehicle loading as required by national highway traffic safety admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or b-pillar. Vehicle certification label your vehicle has a vehicle certification label attached to the driver’s door b-pillar. The la...

  • Page 416

    Inflation pressure this is the cold tire inflation pressure for your vehicle for all loading conditions up to full gawr. Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants ...

  • Page 417

    Caution! Do not load your vehicle any heavier than the gvwr. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. Trailer towing in this section you will find safety ti...

  • Page 418

    Measure gtw is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Gross axle weight rating (gawr...

  • Page 419

    Trailer sway control the trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. Weight-carryi...

  • Page 420

    Warning! (continued) • weight distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable recreational vehicle dealer for additional information. Trailer hitch classification the following chart provides the industry standard ...

  • Page 421

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/transmission frontal area maximum gtw (gross trailer wt.) maximum tongue wt. (see note) 2.0l auto/man 22 sq ft (2.04 sq m) 1,000 lbs (450 ...

  • Page 422

    Which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer collisions. Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items when computing the weight on the rear axle of t...

  • Page 423

    Caution! • do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle. Thi...

  • Page 424

    Warning! (continued) • safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • vehicles with trailers should not be parke...

  • Page 425

    “tires – general information” in “starting and oper- ating” for proper tire inflation procedures. • check the trailer tires for proper tire inflation pres- sures before trailer usage. • check for signs of tire wear or visible tire damage before towing a trailer. Refer to “tires – general information...

  • Page 426

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Warning! • do not connect trailer brake...

  • Page 427

    The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground...

  • Page 428

    Towing tips before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Manual transmission – if equipped if using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippag...

  • Page 429

    To prevent excess heat generation, avoid continuous driving at high rpm. Reduce vehicle speed as necessary to avoid extended driving at high rpm. Return to a higher gear or vehicle speed when grade and road conditions allow. Electronic speed control – if equipped • do not use in hilly terrain or wit...

  • Page 430

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmission automatic transmission flat tow none • transmission in neutral • key in acc position not allowed dolly tow front ok (fwd only) ok (fwd only) rear not all...

  • Page 431: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .431 䡵 if your engine overheats . . . . . . . . . . . .431 䡵 automatic transmission overheating . . . . . . . . . . . . . . . . . . . . . . .432 䡵 wheel and tire torque specifications. . . . . . . . . . . . . . . . . . ...

  • Page 432

    ▫ jump-starting procedure . . . . . . . . . . . . . . . .458 䡵 freeing a stuck vehicle . . . . . . . . . . . . .461 䡵 shift lever override . . . . . . . . . . . . . . . .462 䡵 towing a disabled vehicle. . . . . . . . . . .464 ▫ with ignition key . . . . . . . . . . . . . . . . . . . . .465 430 what ...

  • Page 433

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency...

  • Page 434

    Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the n...

  • Page 435

    Wheel and tire torque specifications proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any time a wheel has been removed and reinstalled on the vehicle the lug nuts/bolts should be torqued using a properly calibrated torque wrench. Torque speci...

  • Page 436

    Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten...

  • Page 437

    Warning! (continued) • being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be ra...

  • Page 438

    Preparations for jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the whe...

  • Page 439

    Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • turn on the hazard warning flasher. • block the ...

  • Page 440

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. Note: refer to “tires — general information” in “start- ing and operating” for further information about the spare tire, it’s use, and operation. 1. Remove th...

  • Page 441

    2. Loosen, but do not remove, the wheel nuts by turning them to the left one turn while the wheel is still on the ground. Note: there are front and rear jacking locations on each side of the body. The front locations are outlined by two triangular cutouts on one of the flanges in the sill flange ass...

  • Page 442

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated. Jacking locations front jacking location 440 what to do in emergencies.

  • Page 443

    Do not raise the vehicle until you are sure the jack is securely engaged. 3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to th...

  • Page 444

    5. Remove the wheel nuts and pull the wheel and wheel covers, where applicable, off the hub. Install the spare wheel and wheel nuts with the cone shaped end of the nuts toward the wheel. Lightly tighten the nuts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the whee...

  • Page 445

    Warning! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. Note: the wheel cover is held on the wheel by the wheel nuts. When reinstalling the original wheel, prop- erly align the wheel cover to the valve stem, place the wheel cover onto the ...

  • Page 446

    Warning! A loose tire thrown forward in a collision or hard stop could injure the occupants in the vehicle. Have the deflated (flat) tire repaired or replaced immediately. 10. Check the spare tire pressure as soon as possible. Correct the tire pressure as required. 11. After 25 miles (40 km) check t...

  • Page 447

    3. Install the five wheel lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in pe...

  • Page 448

    5. After 25 miles (40 km) check the lug nut torque with a torque wrench to ensure that all lug nuts are properly seated against the wheel. Tirefit kit — if equipped small punctures up to 1/4 in (6 mm) in the tire tread can be sealed with tirefit. Foreign objects (e.G., screws or nails) should not be...

  • Page 449

    4. Power button 5. Mode select knob 6. Sealant hose (clear) 7. Air pump hose (black) 8. Power plug using the mode select knob and hoses your tirefit kit is equipped with the following symbols to indicate the air or sealant mode. Selecting air mode turn the mode select knob (5) to this position for a...

  • Page 450

    Tirefit usage precautions • using the tirefit sealant may cause the tire pressure monitoring system (tpms) to become inoperable. It is recommended that you take your vehicle to an autho- rized dealer to have the sensor function checked. • replace the tirefit sealant bottle (1) and sealant hose (6) p...

  • Page 451

    Warning! • do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the tirefit kit. • do not use tirefit or drive the vehicle under the following circumstances: – if the puncture in the tire tread is approx...

  • Page 452

    Warning! (continued) • tirefit sealant solution contains latex. In case of an allergic reaction or rash, consult a physician immedi- ately. Keep tirefit out of reach of children. If swallowed, rinse mouth immediately with plenty of water and drink plenty of water. Do not induce vomiting! Consult a p...

  • Page 453

    3. Place the tirefit kit flat on the ground next to the deflated tire. 4. Remove the cap from the valve stem and then screw the fitting at the end of the sealant hose (6) onto the valve stem. 5. Uncoil the power plug (8) and insert the plug into the vehicle’s 12 volt power outlet. Note: do not remov...

  • Page 454

    2. Connect the power plug (8) to a different 12 volt power outlet in your vehicle or another vehicle, if available. Make sure the engine is running before turning on the tirefit kit. 3. The sealant bottle (1) may be empty due to previous use. Call for assistance. Note: if the mode select knob (5) is...

  • Page 455

    Note: if the tire becomes over-inflated, press the defla- tion button to reduce the tire pressure to the recom- mended inflation pressure before continuing. If the tire inflates to the recommended pressure or is at least 26 psi (1.8 bar) pressure within 15 minutes: 1. Press the power button (4) to t...

  • Page 456

    Warning! Tirefit is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after using tirefit. Do not exceed 55 mph (88 km/h) until the tire is repaired or replaced. Failure to follow this warning can result in injuries that are serious or fatal to you, your passengers, ...

  • Page 457

    2. Disconnect the tirefit kit from the valve stem, reinstall the cap on the valve stem and unplug from 12 volt outlet. 3. Place the tirefit kit in its proper storage area in the vehicle. 4. Have the tire inspected and repaired or replaced at the earliest opportunity at an authorized dealer or tire s...

  • Page 458

    6. Verify that the cap is installed on the fitting at the end of the sealant hose (6) and return the hose to its storage area (located on the bottom of the air pump). 7. Return the tirefit kit to its storage location in the vehicle. Jump-starting procedures if your vehicle has a discharged battery i...

  • Page 459

    Air intake finger screws positive battery post 6 what to do in emergencies 457.

  • Page 460

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 461

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Note: remove air intake before proceeding with this jump-starting procedure. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the...

  • Page 462

    Once the engine is started, remove the jumper cables in the reverse sequence: 6. Disconnect the negative (-) jumper cable from the engine ground of the vehicle with the discharged battery. 7. Disconnect the negative end (-) of the jumper cable from the negative (-) post of the booster battery. 8. Di...

  • Page 463

    Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Then shift back and forth between drive and reverse (with automatic transmission) or 2nd gear an...

  • Page 464

    Caution! • when “rocking” a stuck vehicle by shifting be- tween drive/2nd gear and reverse, do not spin the wheels faster than 15 mph (24 km/h), or drive- train damage may result. • revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damag...

  • Page 465

    4. Turn the ignition switch to the acc or on/run position, but do not start the engine. 5. Press and maintain firm pressure on the brake pedal. 6. Insert the screwdriver or similar tool into the access port, and push and hold the override release lever forward. 7. Move the shift lever to the neutral...

  • Page 466

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial wrecker service. Towing condition wheels off the ground manual transmission automatic transmis- sion (fwd only) automatic transmis- sion 4wd flat tow none • transmission in neutral • key in a...

  • Page 467

    With ignition key automatic transmission • front wheel drive (fwd) vehicles can be towed with the front wheels elevated, or on a flatbed truck (all four wheels off the ground). • four-wheel drive (4wd) vehicles can be towed on a flatbed truck (all four wheels off the ground). If the transmission is ...

  • Page 468

    • fwd vehicles can be towed with the front wheels elevated. • fwd or 4wd vehicles can be towed on a flatbed truck (all wheels off the ground). Caution! Do not flat tow any disabled vehicle if condition is related to the clutch, transmission or driveline. Ad- ditional damage to the drivetrain could r...

  • Page 469: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 2.0l . . . . . . . . . .469 䡵 engine compartment — 2.4l . . . . . . . . . .470 䡵 onboard diagnostic system — obd ii . .471 ▫ loose fuel filler cap message . . . . . . . . . . . .471 䡵 emissions inspection and maintenance programs . . . . . . ....

  • Page 470

    ▫ automatic transmission (six-speed) – if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .496 ▫ automatic transmission (cvt) – if equipped. . .498 ▫ manual transmission – if equipped . . . . . . . .500 ▫ rear drive assembly (rda) – awd/4wd models only . . . . . . . . . . . . . . . . . ...

  • Page 471

    Engine compartment — 2.0l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 7 maintaining your vehicle 46...

  • Page 472

    Engine compartment — 2.4l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 470 maintaining your vehicle.

  • Page 473

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 474

    Persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the mil. Resolving the problem will turn the mil light off. Emissions inspection and maintenance programs in some localities, ...

  • Page 475

    3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 476

    Available which include detailed service information for your vehicle. Refer to these service manuals before attempting any procedure yourself. Note: intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. Warning! Y...

  • Page 477

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, power steering...

  • Page 478

    Caution! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Also, be sure the oil fill cap is replaced and tightened after adding oil. Change engine oil the oil change i...

  • Page 479

    Caution! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the new vehicle limited warranty. Engine oil viscosity (sae grade) sae 5w-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperatu...

  • Page 480

    Station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection this manufacturer’s engines have a full-flow ...

  • Page 481

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 482

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be ...

  • Page 483

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 484

    The a/c air filter is located in the fresh air inlet behind the glove box. Perform the following procedure to re- place the filter: 1. Open the glove compartment and remove all contents. 2. Push in on the sides of the glove compartment and lower the door. 3. Pivot the glove compartment downward. 4. ...

  • Page 485

    6. Install the a/c air filter with the arrow on the filter pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover. Caution! The a/c air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly i...

  • Page 486

    Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact...

  • Page 487

    Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle i...

  • Page 488

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine perfor- mance and cause serious damage to the engine. • damage to the catalytic converter can res...

  • Page 489

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires di...

  • Page 490

    Coolant checks check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed, and refilled with fresh engine coolant (anti- freeze). Chec...

  • Page 491

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 492

    You use the same engine coolant (oat coolant conform- ing to ms-12106) throughout the life of your vehicle. Please review these recommendations for using organic additive technology (oat) engine coolant (antifreeze) that meets the requirements of chrysler material stan- dard ms-12106. When adding en...

  • Page 493

    The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loo...

  • Page 494

    The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for the coolant freeze point or replacing the engine coolant (antifreeze). Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bot...

  • Page 495

    • make sure that the coolant expansion bottle overflow hoses are not kinked or obstructed. • keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • do not change the thermostat for summer or winter operation. If replacement i...

  • Page 496

    When the pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Note: if your vehicle is equipped with a manual trans- mission , the brake fluid reservoir supplies fluid to both the brake system and the clutch release system. The two systems are separated in...

  • Page 497

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 498

    Automatic transmission (six-speed) – if equipped selection of lubricant (six-speed transmission) it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s recommended transmission fluid. Refer to “fluids, lubricants, and gen...

  • Page 499

    Caution! Using a transmission fluid other than the manufactur- er’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder, and will require more frequent fluid and filter changes. Refer to “fluids, lubricants, and genuine parts” in this section for f...

  • Page 500

    Caution! If a transmission fluid leak occurs, visit your autho- rized dealer immediately. Severe transmission dam- age may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately. Fluid and filter changes under normal operating conditions, the fluid installed at the f...

  • Page 501

    Caution! • do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the new vehicle limited warranty. • using a transmission fluid other than the manufac- turer’s recommended fluid will cause belt slip and result in a co...

  • Page 502

    Your authorized dealer immediately to have the trans- mission fluid level checked. Operating the vehicle with an improper fluid level can cause severe transmission damage. Caution! If a transmission fluid leak occurs, visit your autho- rized dealer immediately. Severe transmission dam- age may occur...

  • Page 503

    Note: if contaminated with water, the fluid should be changed immediately. Rear drive assembly (rda) – awd/4wd models only lubricant selection use only the manufacturers recommended transmission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further informa...

  • Page 504

    Frequency of fluid change refer to the “maintenance schedule” for the proper maintenance intervals. Appearance care and protection from corrosion protection of body and paint from corrosion vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads p...

  • Page 505

    Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar® car wash, or a mild car wash soap, and rinse the panels completely with clear water. • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar® super kleen bug and tar remover...

  • Page 506

    • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as...

  • Page 507

    Stain repel fabric cleaning procedure – if equipped stain repel seats may be cleaned in the following man- ner: • remove as much of the stain as possible by blotting with a clean, dry towel. • blot any remaining stain with a clean, damp towel. • for tough stains, apply mopar® total clean, or a mild ...

  • Page 508

    Warning! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Caution! Do not use alcohol and alcohol-based and/or keton based cleaning products to clean leather seats, as damage to the seat may result. Clean...

  • Page 509

    When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Instrument panel cover the instrument panel cover has a low glare surface which minimizes reflections on the windshield. Do not use protectants or other products whi...

  • Page 510

    Replace the belts if they appear frayed or worn or if the buckles do not work properly. Fuses warning! • when replacing a blown fuse, always use an ap- propriate replacement fuse with the same amp rating as the original fuse. Never replace a fuse with another fuse of higher amp rating. Never replace...

  • Page 511

    Cavity cartridge fuse mini-fuse descrip- tion 1 empty empty cavity cartridge fuse mini-fuse descrip- tion 2 15 amp lt blue awd/ 4wd con- trol mod- ule – if equipped 3 10 amp red rear cen- ter brake light switch 4 10 amp red ignition switch/ occupant classifica- tion mod- ule integrated power module ...

  • Page 512

    Cavity cartridge fuse mini-fuse descrip- tion 5 20 amp yellow trailer tow – if equipped 6 10 amp red power mirror/ steering control satellite radio/ hands-free phone 7 30 amp green ignition off draw 8 30 amp green ignition off draw cavity cartridge fuse mini-fuse descrip- tion 9 40 amp green power s...

  • Page 513

    Cavity cartridge fuse mini-fuse descrip- tion 14 10 amp red instrument cluster 15 40 amp green radiator fan 16 15 amp lt blue dome lamp/ sunroof/ rear wiper motor 17 10 amp red wireless control module 18 40 amp green auto shut- down re- lay cavity cartridge fuse mini-fuse descrip- tion 19 20 amp yel...

  • Page 514

    Cavity cartridge fuse mini-fuse descrip- tion 24 15 amp lt blue power sun- roof – if equipped 25 10 amp red heated mirror – if equipped 26 15 amp lt blue auto shut- down re- lay 27 10 amp red airbag control module cavity cartridge fuse mini-fuse descrip- tion 28 10 amp red airbag control module/ occ...

  • Page 515

    Cavity cartridge fuse mini-fuse descrip- tion 32 30 amp pink auto shut- down re- lay 33 10 amp red j1962 conn/ powertrain control module 34 30 amp pink antilock brakevalve 35 40 amp green antilock brake pump cavity cartridge fuse mini-fuse descrip- tion 36 30 amp pink headlamp/ washer control/ smart...

  • Page 516

    Caution! • when installing the ipm cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the ipm, and possibly result in an electrical system failure. • when replacing a blown fuse, it is important to use only a fuse having ...

  • Page 517

    Replacement bulbs interior bulbs bulb number front header lamp t578 center dome lamp t578 rear cargo lamp/ flashlight 8–a35lfaa exterior bulbs bulb number low beam headlamp h11 premium low beam headlamp hir2 high beam headlamp 9005 premium high beam headlamp hir2 bulb number daytime running light (d...

  • Page 518

    Bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Headlamps 1. Raise the hood and loc...

  • Page 519

    Rear turn signal and backup lamp 1. Remove the two push-pins from the taillamp housing. 2. Grasp the taillamp and pull firmly to disengage the lamp from the aperture panel. 3. Twist and remove socket from lamp. 4. Remove bulb from socket and replace. License lamps 1. Use a screw driver to gently pry...

  • Page 520

    Fluid capacities u.S. Metric fuel (approximate) 13.6 gallons 51.5 liters engine oil with filter 2.0l and 2.4l engine (sae 5w-20, api certified) 4.5 quarts 4.26 liters cooling system * 2.0l and 2.4l engine (mopar® antifreeze/engine coolant 10 year/150,000 mile formula or equivalent) 7.2 quarts 6.8 li...

  • Page 521

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of chrysler material standard ms-12106. Engine o...

  • Page 522

    Chassis component fluid, lubricant, or genuine part automatic transmission (cvt) – if equipped we recommend you use mopar® cvtf+4® continu- ously variable transmission fluid. Automatic transmission (six-speed) - if equipped we recommend you use sk energy atf sp-4 transmis- sion fluid. Manual transmi...

  • Page 523: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .522 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .523 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 524

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 525

    • check the fluid levels of the coolant reservoir, brake master cylinder, power steering and fill as needed • check function of all interior and exterior lights required maintenance intervals . Refer to the maintenance schedules on the following page for the required maintenance intervals. At every ...

  • Page 526

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 527

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 528

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 529

    ** the spark plug change interval is mileage based only, yearly intervals do not apply. Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a servi...

  • Page 531: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .531 ▫ prepare for the appointment. . . . . . . . . . . . .531 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .531 ▫ be reasonable with requests ....

  • Page 532

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .537 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .537 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .537 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .538 530 if...

  • Page 533

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 534

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 535

    In mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has insta...

  • Page 536

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 537

    Mopar® parts mopar® fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehi...

  • Page 538

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 539

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 540

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 541: Index

    Index 10

  • Page 542

    Abs (anti-lock brake system) . . . . . . . . . . . . . . . .358 adding engine coolant (antifreeze) . . . . . . . . . . . .489 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .410 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .484 additives, fuel . . . . . . . . . ...

  • Page 543

    Automatic transmission . . . . . . . . . . . . . . . . . . . .324 fluid and filter changes . . . . . . . . . . . . . . . . . .498 fluid level check . . . . . . . . . . . . . . . . . . . . . . .497 fluid type . . . . . . . . . . . . . . . . . . . . . . . . . . . .496 gear ranges . . . . . . . . . . ....

  • Page 544

    Cargo compartment . . . . . . . . . . . . . . . . . . . . . . .201 light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .201 luggage carrier . . . . . . . . . . . . . . . . . . . . . . . .208 cargo light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .201 cargo load floor . ....

  • Page 545

    Coolant pressure cap (radiator cap) . . . . . . . . . . .490 cooling system. . . . . . . . . . . . . . . . . . . . . . . . . . .487 adding coolant (antifreeze) . . . . . . . . . . . . . . .489 coolant level . . . . . . . . . . . . . . . . . . . . . . . . . .488 disposal of used coolant . . . . . . ....

  • Page 546

    Electronic brake control system . . . . . . . . . . . . . . .361 anti-lock brake system . . . . . . . . . . . . . . . . . .361 brake assist system . . . . . . . . . . . . . . . . . . . . .362 electronic roll mitigation . . . . . . . . . . . . . . . . .363 traction control system . . . . . . . . . . ...

  • Page 547

    Air conditioning . . . . . . . . . . . . . . . . . . . . . . . .311 engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . .478 engine oil disposal . . . . . . . . . . . . . . . . . . . . .477 flashers hazard warning . . . . . . . . . . . . . . . . . . . . . . . .431 turn signal . . . . . ...

  • Page 548

    Tank capacity . . . . . . . . . . . . . . . . . . . . . . . . . .518 fueling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .410 fuel system caution . . . . . . . . . . . . . . . . . . . . . . .411 fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .508 garage doo...

  • Page 549

    Hill start assist. . . . . . . . . . . . . . . . . . . . . . . . . . .366 hitches trailer towing . . . . . . . . . . . . . . . . . . . . . . . . .418 homelink® (garage door opener) . . . . . . . . . . . .180 hood release . . . . . . . . . . . . . . . . . . . . . . . . . . . .162 ignition . . . . . ....

  • Page 550

    Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .162 lead free gasoline . . . . . . . . . . . . . . . . . . . . . . . .406 leaks, fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 life of t...

  • Page 551

    Security alarm (theft alarm) . . . . . . . . . . . . . . . .19 service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .516 theft alarm (security alarm) . . . . . . . . . . . . . . .221 tire pressure monitoring (tpms) . . . . . . . . . . . .223 traction control . . . . . . . . . . . . . ...

  • Page 552

    Automatic dimming . . . . . . . . . . . . . . . . . . . . .109 electric powered . . . . . . . . . . . . . . . . . . . . . . . .110 exterior folding . . . . . . . . . . . . . . . . . . . . . . . .110 heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 outside . . . . . . . . . . ....

  • Page 553

    Operator manual (owner’s manual) . . . . . . . . . . . . .5 overheating, engine . . . . . . . . . . . . . . . . . . . . . . .222 owner’s manual (operator manual) . . . . . . . . . . . . .5 paint care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .502 panic alarm . . . . . . . . . . . . ....

  • Page 554

    Rearview mirrors . . . . . . . . . . . . . . . . . . . . . . . . .108 rear window defroster . . . . . . . . . . . . . . . . . . . . .207 rear window features . . . . . . . . . . . . . . . . . . . . .206 rear wiper/washer. . . . . . . . . . . . . . . . . . . . . . . .206 recorder, event data . . . . ...

  • Page 555

    Adjustable shoulder belt . . . . . . . . . . . . . . . . . . .49 adjustable upper shoulder anchorage . . . . . . . . .49 and pregnant women . . . . . . . . . . . . . . . . . . . . .61 child restraint . . . . . . . . . . . . . . . . . . . . . . . . . .76 extender . . . . . . . . . . . . . . . . . . ....

  • Page 556

    Speedometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . .217 starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .318 automatic transmission . . . . . . . . . . . . . . . . . .319 cold weather . . . . . . . . . . . . . . . . . . . . . . . . . .320 engine fails to start ...

  • Page 557

    Compact spare . . . . . . . . . . . . . . . . . . . . . . . . .389 general information . . . . . . . . . . . . . . . . . . . . .384 high speed . . . . . . . . . . . . . . . . . . . . . . . . . . .386 inflation pressures . . . . . . . . . . . . . . . . . . . . . . .385 jacking . . . . . . . . . . . ....

  • Page 558

    Trailer weight . . . . . . . . . . . . . . . . . . . . . . . . . . . .419 transaxle automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 transmission automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . .324 fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 559

    Washer adding fluid . . . . . . . . . . . . . . . . . . . . . . . . . .484 washers, windshield . . . . . . . . . . . . . . . . . . . . . . .172 washing vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .503 wheel and wheel trim . . . . . . . . . . . . . . . . . . . . .504 wheel and wheel tri...

  • Page 561

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 562

    1283259cv1 14wk741-126-aa grand cherokee chrysler 1" gutter 12/05/2012 15:56:03 grand cherokee chrysler group llc o w n e r ’ s m a n u a l 2014 gr and cher ok ee 14wk741-126-aa second edition printed in u.S.A. 2 0 1 4 grand cherokee chrysler group llc o w n e r ’ s m a n u a l 2014 gr and cher ok e...