1. DL manuals
  2. Jeep
  3. Automobile
  4. 2014 Compass
  5. Owner's Manual

Jeep 2014 Compass Owner's Manual

Summary of 2014 Compass

  • Page 1

    Compass chrysler group llc o w n e r ’ s m a n u a l 20 14 c ompas s 14mk49-126-ae fifth edition printed in u.S.A. 2 0 1 4.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the feat...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 rollover warning . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .5 䡵 warnings and cautions . . . . . . . . . . . . . .7 䡵 vehicle identification number . . . . . . . .7 ...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    Control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully. Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the unive...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owners manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss importan...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right front body vin location 8 introduct...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .12 ▫ locking doors with a key. . . . . . . . . . . . . . . .14 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .14 䡵 sentry k...

  • Page 12

    ▫ sound horn with remote key lock . . . . . . . . .22 ▫ flash lights with remote key lock/unlock . . .23 ▫ using the panic alarm . . . . . . . . . . . . . . . . . .24 ▫ programming additional transmitters. . . . . . . .25 ▫ transmitter battery replacement . . . . . . . . . . .25 ▫ general informatio...

  • Page 13

    ▫ energy management feature . . . . . . . . . . . . . .55 ▫ seat belt pretensioners . . . . . . . . . . . . . . . . . .56 ▫ supplemental active head restraints (ahr) . . .56 ▫ enhanced seat belt use reminder system (beltalert®) . . . . . . . . . . . . . . . . . . . . . . . . . .60 ▫ seat belt extend...

  • Page 14

    A word about your keys the authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition key removal 1. Place the shift lever in...

  • Page 15

    Note: if you try to remove the key before you place the shift lever in park, the key may become trapped tem- porarily in the ignition switch cylinder. If this occurs, place the shift lever in park, rotate the key clockwise slightly, then remove the key as described above. If a malfunction occurs, th...

  • Page 16

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the shift lever. • do not leave the key fob in or near the ...

  • Page 17

    Sentry key® the sentry key® immobilizer system prevents unau- thorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys that have an embedded el...

  • Page 18

    Caution! The sentry key® immobilizer system is not compat- ible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the keys provided with your new vehicle have been programmed to the vehicle electronics....

  • Page 19

    Customer key programming if you have two valid sentry keys®, you can program new sentry keys® to the system by performing the following procedure: 1. Cut the additional sentry key® transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the igniti...

  • Page 20

    Note: if a programmed key is lost, see your authorized dealer to have all remaining keys erased from the sys- tem’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of s...

  • Page 21

    To arm the system 1. Remove the key from the ignition switch and get out of the vehicle. 2. Lock the door using either the power door lock switch or the remote keyless entry (rke) transmitter and close all doors. 3. The vehicle security light in the instrument cluster will flash rapidly for approxim...

  • Page 22

    Once the vehicle security alarm is armed (after 16 seconds), when you pull the door handle to exit, the alarm will sound. If this occurs, press the unlock button on the rke transmitter to disarm the vehicle security alarm. Vehicle security alarm manual override the vehicle security alarm will not ar...

  • Page 23

    To unlock the doors and liftgate press and release the unlock button on the rke transmitter once to unlock the driver’s door, or twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn...

  • Page 24

    Note: pressing the lock button on the rke transmit- ter while you are inside the vehicle will activate the vehicle security alarm. Opening a door with the vehicle security alarm activated will cause the alarm to sound. Press the unlock button to deactivate the vehicle security alarm. Illuminated app...

  • Page 25

    • for vehicles not equipped with the evic, perform the following steps: 1. Press the lock button on a programmed rke trans- mitter for at least 4 seconds, but no longer than 10 seconds. Then, press the panic button while still holding the lock button. 2. Release both buttons at the same time. 3. Tes...

  • Page 26

    • for vehicles not equipped with the evic, perform the following steps: 1. Press and hold the unlock button on a programmed rke transmitter for at least 4 seconds, but no longer than 10 seconds. Then, press and hold the lock button while still holding the unlock button. 2. Release both buttons at th...

  • Page 27

    Note: when you turn off the panic alarm by pressing the panic button a second time, you may have to move closer to the vehicle due to the radio frequency noises of the system. Programming additional transmitters refer to sentry key® “customer key programming”. If you do not have a programmed rke tra...

  • Page 28

    Note: if the rke transmitter is equipped with a screw, reinstall and tighten the screw until snug. General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference...

  • Page 29

    Note: • the vehicle must be equipped with an automatic transmission to be equipped with remote start. • obstructions between the vehicle and the key fob may reduce this range. How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in pa...

  • Page 30

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted — door ajar • remote start aborted — hood ajar • remote start abor...

  • Page 31

    • the engine can be started two consecutive times (two 15-minute cycles) with the rke transmitter. However, the ignition switch must be cycled to the on/run position before you can repeat the start sequence for a third cycle. Remote start will also cancel if any of the following occur: • the engine ...

  • Page 32

    Door locks manual door locks use the manual door lock knob to lock the doors from inside the vehicle. If the lock knob is down when the door is closed, the door will lock. Make sure the keys are not inside the vehicle before closing the door. Warning! • for personal security and safety in the event ...

  • Page 33

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 34

    Auto lock doors — if equipped the auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). Auto lock doors programming the automatic door locks feature can be enabled or disabled as follows: • for veh...

  • Page 35

    2. Within 15 seconds, cycle the ignition switch between lock and on/run and then back to lock four times ending up in the lock position (do not start the engine). 3. Within 30 seconds, press the power door lock switch to lock the doors. 4. A single chime will indicate the completion of the programmi...

  • Page 36

    Equipped/personal settings (customer- programmable features)” in “understanding your in- strument panel” for further information. • for vehicles not equipped with the evic, perform the following procedure: 1. Close all doors and place the key in the ignition. 2. Within 15 seconds, cycle the ignition...

  • Page 37

    To engage or disengage the child-protection door lock system 1. Open the rear door. 2. Insert the tip of the ignition key into the lock and rotate to the lock or unlock position. 3. Repeat steps 1 and 2 for the opposite rear door. Child-protection door lock location 2 things to know before starting ...

  • Page 38

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Note: for emergency exit with the system engaged, move the lock knob up (unlocked position), roll down the window and open the doo...

  • Page 39

    • for vehicles equipped with the evic, the power window switches will remain active for up to 10 minutes after the ignition switch is turned to the lock position. Opening either front door will cancel this feature. The time for this feature is programmable. Refer to “electronic vehicle information c...

  • Page 40

    Auto-down the driver’s door window switch has an auto-down feature. Push the window switch past the first detent, release, and the window will go down automatically. To cancel the auto-down movement, operate the switch in either the up or down direction and release the switch. Window lockout switch ...

  • Page 41

    Liftgate note: the key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate. To unlock the liftgate, insert the key into the lock and turn it to the right (manual lock models only). The liftgate can also be unlocked using the remote keyless entry (rke) tra...

  • Page 42

    • although the liftgate has no inside release mechanism, the liftgate trim panel includes an opening with a snap-in cap that provides access to release the latch in the event of an electrical system malfunction. Warning! • driving with the liftgate open can allow poisonous exhaust gases into your ve...

  • Page 43

    • supplemental seat-mounted side air bags (sab) — if equipped • an energy-absorbing steering column and steering wheel • knee bolsters/blockers for front seat occupants • front seat belts incorporate pretensioners that may enhance occupant protection by managing occupant energy during an impact even...

  • Page 44

    Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: 1. Children 12 years old and under should always ride buckled up in a rear seat. Warning! • never place a rear facing infant seat in front of an air bag. A deploying passenger advanced front air bag can ca...

  • Page 45

    4. Do not lean against the door or window. If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between you and the door. 5. If the air bag system in this vehicle needs to be modified to accommodate a disabled person, contact the customer...

  • Page 46

    Warning! (continued) • in a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up...

  • Page 47

    Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure ever...

  • Page 48

    The belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”. Pulling out the latch plate inserting latch plate into buckle 46 things to know before ...

  • Page 49

    Warning! • a belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal inju- ries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you prop- erly. In a sudden stop you...

  • Page 50

    4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. War...

  • Page 51

    6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed posi- tion. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. Warning! A frayed or torn belt could rip apart in a collision and leave you with no protec...

  • Page 52

    As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average you will prefer a higher position. When you release the anchorage, try to move it down to make sure that it is locked in position. In the rear seat, move toward the center of the seat to ...

  • Page 53

    2. Grasp the mini-latch plate and pull the belt over the seat. 3. Route the shoulder belt to the inside of the right head restraint. 4. When the belt is long enough to fit, insert the mini- latch plate into the mini-buckle until you hear a “click”. 5. Sit back in the seat. Slide the regular latch pl...

  • Page 54

    6. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”. 7. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, pull on the lap ...

  • Page 55

    10. To disengage the mini-latch from the mini-buckle for storage, insert the regular latch plate into the black button on the top of the mini-buckle. The belt will automatically retract to its stowed position. If neces- sary, slide the latch plate down the webbing to allow the belt to retract fully....

  • Page 56

    4. Continue to slide the latch plate up until it clears the folded webbing. Seat belts in passenger seating positions the seat belts in the passenger seating positions are equipped with automatic locking retractors (alr) which are used to secure a child restraint system. For additional information, ...

  • Page 57

    Position that has a belt with this feature. Children 12 years old and under should always be properly re- strained in a vehicle with a rear seat. How to engage the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire...

  • Page 58

    Seat belt pretensioners the seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by assuring that the belt is tight about the oc...

  • Page 59

    This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts. Note: the active head restraints (ahr) may or may not deploy in the event of a front or side impact. However if during a front impact, a secondary rear impact ...

  • Page 60

    Caution! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. Note: for more information on properly adjusting and positi...

  • Page 61

    3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. 1 — downward movement 2 — rearward movement 3 — final downward movement to engage locking mechanism review table below 2 things to know before starting your vehicle 59.

  • Page 62

    4. The ahr front soft foam and trim half should lock into the back decorative plastic half. Note: • if you have difficulties or problems resetting the active head restraints, see an authorized dealer. • for safety reasons, have the active head restraints checked by a qualified specialist at an autho...

  • Page 63

    Light remains illuminated until the respective seat belts are fastened. The driver should instruct all other occu- pants to fasten their seat belts. If a front seat belt is unbuckled while traveling at speeds greater than 5 mph (8 km/h), beltalert® will provide both audio and visual notification. Th...

  • Page 64

    Warning! (continued) when the seat belt is not long enough when it is worn low and snug and in the recommended seating posi- tions. Remove and store the extender when not needed. Seat belts and pregnant women we recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the...

  • Page 65

    Note: the driver and passenger advanced front air bags are certified to new federal regulations. The advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation that are based on the severity and type of collision. This vehicle may be equip...

  • Page 66

    Protection for an occupant during a side impact. The supplemental seat-mounted side air bags are located in the outboard side of the front seats. Note: • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • after any collision, the vehicle should be...

  • Page 67

    The first stage inflator is triggered immediately during an impact that requires air bag deployment. This low output is used in less severe collisions. A higher energy output is used for more severe collisions. Warning! • no objects should be placed over or near the air bag on the instrument panel, ...

  • Page 68

    Supplemental seat-mounted side air bags (sab) — if equipped supplemental seat-mounted side air bags (sab) may provide enhanced protection to help protect an occupant during a side impact. The sab is marked with an air bag label sewn into the outboard side of the front seats. When the air bag deploys...

  • Page 69

    Note: • should a vehicle rollover occur, the pretensioners and/or sab and sabic curtains on both sides of the vehicle may deploy. • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • being too close to the supplemental side air bag inflatable curt...

  • Page 70

    Warning! (continued) • do not use accessory seat covers or place objects between you and the sab; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury. • your vehicle is equipped with sabic air bags, do not have any accessory items installed whi...

  • Page 71

    Air bag deployment sensors and controls occupant restraint controller (orc) the orc is part of a federally regulated safety system required for this vehicle. The orc determines if deployment of the front and/or side air bags in a frontal or side collision is required. Based on the impact sensor’s si...

  • Page 72

    The orc monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the start or on/run position. If the key is in the off position, in the acc position, or not in the ignition, the air bag system is not on and the air bags will not inflate. The orc contai...

  • Page 73

    When the orc detects a collision requiring the ad- vanced front air bags, it signals the inflator units. A large quantity of non-toxic gas is generated to inflate the advanced front air bags. Different air bag inflation rates are possible, based on several factors, including the collision type and s...

  • Page 74

    Supplemental side air bag inflatable curtain (sabic) inflator units during collisions where the impact is confined to a particular area of the side of the vehicle, the orc may deploy the sabic air bags, depending on the severity and type of collision. In these events, the orc will deploy the sabic o...

  • Page 75

    • flash hazard lights as long as the battery has power or until the ignition key is turned off. • turn on the interior lights, which remain on as long as the battery has power or until the ignition key is removed. • unlock the doors automatically. In order to reset the enhanced accident response sys...

  • Page 76

    Throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s in- structions for cleaning. Do not drive your vehicle after the air bags have de- ployed. If you are involved in another collision, the a...

  • Page 77

    Warning! (continued) • do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion,...

  • Page 78

    Note: if the speedometer, tachometer, or any engine related gauges are not working, the occupant restraint controller (orc) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of t...

  • Page 79

    To read data recorded by an edr, special equipment is required, and access to the vehicle or the edr is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equip- ment, can read the information if they have access to the vehicle or the edr. ...

  • Page 80

    Note: • for additional information, refer to www.Seatcheck.Org or call 1–866–seatcheck. Cana- dian residents should refer to transport canada’s website for additional information: • http://www.Tc.Gc.Ca/eng/roadsafety/safedrivers- childsafety-index-53.Htm warning! In a collision, an unrestrained chil...

  • Page 81

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child re- straint either an infant carrie...

  • Page 82

    Infants and child restraints safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carrie...

  • Page 83

    Have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat. Children should remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above t...

  • Page 84

    Warning! (continued) • when your child restraint is not in use, secure it in the vehicle with the seat belt or latch anchor- ages, or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or accident, it could strike the occupants or seatbacks and cause serious personal ...

  • Page 85

    If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the child is using the lap/shoulder belt, check belt fit peri- odically and make sure the seat belt buckle is latched. A child’s squirming or slouching can move the belt out of posi...

  • Page 86

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 87

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 88

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 86 things to know before starting your vehicle.

  • Page 89

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and teth...

  • Page 90

    Can two child restraints be attached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to in- stall a child seat in the center position next to a child s...

  • Page 91

    Locating the latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between ...

  • Page 92

    Locating the latch anchorages in addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to...

  • Page 93

    To install a latch-compatible child restraint 1. If the selected seating position has a switchable auto- matic locking retractor (alr) seat belt, stow the seat belt following the instructions below. See the section “installing child restraints using the vehicle seat belt” to check what type of seat ...

  • Page 94

    7. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. How to stow an unused alr seatbelt when using the latch attaching system to install a child restraint, stow all alr seat...

  • Page 95

    Installing child restraints using the vehicle seat belt the seat belts in the passenger seating positions are equipped with a switchable automatic locking retractor (alr) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a l...

  • Page 96

    What is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward facing child restraint...

  • Page 97

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 98

    The tether strap to the anchorage and tighten the tether strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the seat belt pa...

  • Page 99

    Strap. Refer to “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 6. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25 mm) in any direction. Any...

  • Page 100

    3. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. 4. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. Warning! • an incorrectly anchored tether strap could lead to increased head motion and possib...

  • Page 101

    Engine break-in recommendations a long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While crui...

  • Page 102

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be serious...

  • Page 103

    Warning! (continued) • if it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. The best protection against carbon monoxide entry into the vehicle body is a properly maintained ...

  • Page 104

    Air bag warning light the light should come on and remain on for four to eight seconds as a bulb check when the ignition switch is first turned on. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked...

  • Page 105

    Warning! (continued) • never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfer- ing with the pedals or the ability to control the vehicle. • never put floor mats or other floor coverings on top of already inst...

  • Page 106

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 107: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 ▫ inside day/night mirror . . . . . . . . . . . . . . . .109 ▫ automatic dimming mirror — if equipped . . .110 ▫ outside mirror — driver side . . . . . . . . . . . .111 ▫ outside ...

  • Page 108

    ▫ commands . . . . . . . . . . . . . . . . . . . . . . . . .146 ▫ voice training . . . . . . . . . . . . . . . . . . . . . . .150 䡵 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150 ▫ power seats — if equipped . . . . . . . . . . . . . .151 ▫ heated seats — if equipped . . . . . ....

  • Page 109

    䡵 windshield wipers and washers . . . . . .172 ▫ windshield wiper operation . . . . . . . . . . . . .173 ▫ intermittent wiper system . . . . . . . . . . . . . . .174 ▫ windshield washers . . . . . . . . . . . . . . . . . . .174 ▫ mist feature . . . . . . . . . . . . . . . . . . . . . . . . .175 䡵 ti...

  • Page 110

    ▫ opening sunroof — manual mode . . . . . . . . .194 ▫ closing sunroof — express. . . . . . . . . . . . . . .194 ▫ closing sunroof — manual mode . . . . . . . . . .194 ▫ pinch protect feature . . . . . . . . . . . . . . . . . . .194 ▫ venting sunroof — express . . . . . . . . . . . . . .195 ▫ sunsha...

  • Page 111

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicl...

  • Page 112

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activa...

  • Page 113

    Outside mirror — driver side adjust the flat outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle with your head close to the door glass. Outside mirror — passenger side adjust the convex outside mirror so you can just see the side of your vehi...

  • Page 114

    To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When you are finished adjusting the mirror, turn the control to the center position to prevent accidentally moving a mirror. Heated mirro...

  • Page 115

    Sun visor sliding feature the sun visors may be extended out to provide more coverage of the side glass. Uconnect® phone — if equipped uconnect® phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect® phone al- lows you to dial a phone number with your mobile phone using...

  • Page 116

    For uconnect® customer support: • u.S. Residents - visit www.Uconnectphone.Com or call 1-877-855-8400. • canadian residents - visit www.Uconnectphone.Com or call, 1-800-465-2001 (english) or 1-800-387-9983 (french). Uconnect® phone allows you to transfer calls between the system and your mobile phon...

  • Page 117

    Uconnect® phone button the radio or steering wheel controls (if equipped) will contain the two control buttons (uconnect® phone button and voice com- mand button) that will enable you to access the system. When you press the button you will hear the word uconnect® followed by a beep. The beep is you...

  • Page 118

    • prior to giving a voice command, one must wait for the beep, which follows the “ready” prompt or another prompt. • for certain operations, compound commands can be used. For example, instead of saying “setup” and then “pair a device,” the following compound command can be said: “pair a bluetooth d...

  • Page 119

    Pair (link) uconnect® phone to a mobile phone to begin using your uconnect® phone, you must pair your compatible bluetooth® enabled mobile phone. To complete the pairing process, you will need to refer- ence your mobile phone owner’s manual. The uconnect® website may also provide detailed instruc- t...

  • Page 120

    Can select to use a lower priority mobile phone at any time (refer to “advanced phone connectivity” in this section). Dial by saying a number • press the button to begin. • after the “ready” prompt and the following beep, say “dial.” • the system will prompt you to say the number you want to call. •...

  • Page 121

    • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook new entry.” • when prompted, say the name of the new entry. Use of long names helps the voice command and it is recom- mended. For example, say “robert smith” or “robert” instead of “bob.” • when prompted,...

  • Page 122

    • automatic download and update, if supported, begins as soon as the bluetooth® wireless phone connection is made to the uconnect® phone, for example, after you start the vehicle. • a maximum of 1000 entries per phone will be down- loaded and updated every time a phone is connected to the uconnect® ...

  • Page 123

    • when prompted, recite the new phone number for the phonebook entry that you are editing. After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu. “phonebook edit”...

  • Page 124

    • automatic downloaded phonebook entries cannot be deleted or edited. Delete/erase “all” uconnect® phonebook entries • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook erase all.” • the uconnect® phone will ask you to verify that you wish to delete all the...

  • Page 125

    Phone call features the following features can be accessed through the uconnect® phone if the feature(s) are available on your mobile service plan. For example, if your mobile service plan provides three-way calling, this feature can be accessed through the uconnect® phone. Check with your mobile se...

  • Page 126

    Making a second call while current call is in progress to make a second call while you are currently on a call, press the button and say “dial” or “call” fol- lowed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. To go bac...

  • Page 127

    Established, press and hold the button until you hear a double beep, indicating that the two calls have been joined into one conference call. Call termination to end a call in progress, momentarily press the but- ton. Only the active call(s) will be terminated and if there is a call on hold, it will...

  • Page 128

    2. After the ignition is cycled to off, a call can continue on the uconnect® phone for a certain duration, after which the call is automatically transferred from the uconnect® phone to the mobile phone. 3. An active call is automatically transferred to the mobile phone after the ignition is cycled t...

  • Page 129

    • after the “ready” prompt and the following beep, say “emergency” and the uconnect® phone will instruct the paired mobile phone to call the emergency number. This feature is supported in the u.S., canada, and mexico. Note: • the emergency number dialed is based on the country where the vehicle is p...

  • Page 130

    Note: you should program the desired towing assis- tance phone number using the voice command system. To do this, press the button and say “setup,” followed by “towing assistance.” when prompted say 1-800- 521-2779 for u.S./canada, say 55-14-3454 for mexico city and 1-800-712-3040 for outside mexico...

  • Page 131

    By “send,” is also to be used for navigating through an automated customer service center menu structure, and to leave a number on a pager. You can also send stored uconnect® phonebook entries as tones for fast and easy access to voice mail and pager entries. To use this feature, dial the number you...

  • Page 132

    Turning confirmation prompts on/off turning confirmation prompts off will stop the system from confirming your choices (e.G., the uconnect® phone will not repeat a phone number before you dial it). • press the button to begin. • after the “ready” prompt and the following beep, say one of the followi...

  • Page 133

    Mute/un-mute (mute on/off) when you mute the uconnect® phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. To mute the uconnect® phone: • press the button. • following the beep, say “mute.” to un-mute the uconnect® pho...

  • Page 134

    • when prompted, say “list phones.” • the uconnect® phone will play the phone names of all paired mobile phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the button and say “select” or “delete.” also, see the next two sections for...

  • Page 135

    Things you should know about your uconnect® phone uconnect® phone tutorial to hear a brief tutorial of the system features, press the button and say “uconnect® tutorial.” voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers, the uconnect® pho...

  • Page 136

    This will delete all phone pairing, phone book entries, and other settings in all language modes. The system will prompt you before resetting to factory settings. Voice command • for best performance, adjust the rearview mirror to provide at least ½ inch (1 cm) gap between the overhead console (if e...

  • Page 137

    • it is not recommended to store similar sounding names in the uconnect® phonebook. • phonebook (downloaded and uconnect® phone lo- cal) name recognition rate is optimized when the entries are not similar. • numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight h...

  • Page 138

    • in a convertible vehicle, system performance may be compromised with the convertible top down recent calls if your phone supports “automatic phonebook down- load,” uconnect® phone can list your outgoing, incom- ing and missed calls. Voice text reply uconnect® phone can read or send new messages on...

  • Page 139

    To send a message, press the button while the system is listing the message and say “send.” uconnect® phone will prompt you to say the name or number of the person you wish to send the message to. List of preset messages: 1. Yes. 2. No. 3. Where are you? 4. I need more direction. 5. L o l. 6. Why? 7...

  • Page 140

    Turn voice text reply incoming announcement on/ off turning the voice text reply incoming announcement off will stop the system from announcing the new incoming messages. • press the button. • after the “ready” prompt and the following beep, say “setup, incoming message announcement,” you will then ...

  • Page 141

    3 understanding the features of your vehicle 139.

  • Page 142

    140 understanding the features of your vehicle.

  • Page 143

    3 understanding the features of your vehicle 141.

  • Page 144

    Voice commands primary alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location voice commands primary alternate (s) all call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais 142 understanding ...

  • Page 145

    Voice commands primary alternate (s) help home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book voice commands primary alternate (s) previous record again redial return to main menu return or main menu select phone select...

  • Page 146

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 147

    Warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your at- tention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. When y...

  • Page 148

    To hear the first available menu, press the voice com- mand button and say “help” or “main menu.” commands the voice command system understands two types of commands, universal commands and local commands. Universal commands are available at all times. Local com- mands are available if the supported...

  • Page 149

    Radio am to switch to the am band, say “am” or “radio am.” in this mode, you may say the following commands: • “frequency #” (to change the frequency) • “next station” (to select the next station) • “previous station” (to select the previous station) • “radio menu” (to switch to the radio menu) • “m...

  • Page 150

    Disc mode to switch to the disc mode, say “disc.” in this mode, you may say the following commands: • “track” (#) (to change the track) • “next track” (to play the next track) • “previous track” (to play the previous track) • “main menu” (to switch to the main menu) usb mode to switch to usb mode, s...

  • Page 151

    – “continue” (to continue recording) – “delete” (to delete the recording) • “play memos” (to play previously recorded memos) — during the playback you may press the voice com- mand button to stop playing memos. You pro- ceed by saying one of the following commands: – “repeat” (to repeat a memo) – “n...

  • Page 152

    Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect® voice “voice training” feature may be used. 1. Press the voice command button, say “system setup” and once you are in that menu then say “voice training.” this will train your...

  • Page 153

    Power seats — if equipped some models may be equipped with a power driver’s seat. The power seat switch is located on the outboard side of the seat near the floor. Use the switch to move the seat up, down, forward, rearward, or to tilt the seat. Warning! • adjusting a seat while driving may be dange...

  • Page 154

    Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting the seat up or down the height of the seats...

  • Page 155

    When the high-level setting is selected, the heater will provide a boosted heat level during the initial stages of operation. Then, the heat output will drop to the normal hi-level. If the hi-level setting is selected, the system will automatically switch to low-level after approximately 30 minutes ...

  • Page 156

    Manual front seat adjustment on models equipped with manual seats, the adjusting bar is located at the front of the seats, near the floor. While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once you have reached the desired position. Then, using body...

  • Page 157

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 158

    Manual lumbar — if equipped the lumbar adjustment handle is located on the outboard side of the driver’s seatback. Rotate the lever downward to increase the lumbar support or rotate the lever upward to decrease the lumbar support. Driver’s seatback recline to adjust the seatback, lift the lever loca...

  • Page 159

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Fold-flat front passenger seat — if equipped to fold the front passenger seat, lift th...

  • Page 160

    Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. Warning! The head restraints for all occupants must be ...

  • Page 161

    When ahrs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the ahr. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear imp...

  • Page 162

    Active head restraint (normal position) active head restraint (tilted position) 160 understanding the features of your vehicle.

  • Page 163

    Note: • the head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head re...

  • Page 164

    Rear head restraints the head restraints in the rear are non adjustable. Refer to “occupant restraints” in “things to know before start- ing your vehicle” for information on tether routing. Folding rear seat to provide additional storage area, each rear seatback can be folded forward. Pull the strap...

  • Page 165

    To raise the seatback, pull the strap forward and lift the seatback into its upright position. Warning! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers...

  • Page 166

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. To open and close the hood to open the hoo...

  • Page 167

    Lift the hood prop rod, clipped to the right side (left side facing hood) of the engine compartment to secure the hood in the open position. Place the hood prop at the location stamped into the inner hood surface. Caution! To prevent possible damage, do not slam the hood to close it. Lower the hood ...

  • Page 168

    Caution! (continued) both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure...

  • Page 169

    Daytime running lights — if equipped the high beam lights will come on as daytime running lights (lower intensity), whenever the ignition is on, the engine is running, the headlight switch is off, the parking brake is off, the turn signal is off, and the shift lever is in any position except park. L...

  • Page 170

    Note: the fog lights will only operate with the head- lights on low beam. Selecting high beam headlights will turn off the fog lights. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn ...

  • Page 171

    Note: if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. Lane change assist tap the lever up or down once, without ...

  • Page 172

    Instrument panel dimming rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened. Rotate the center portion of the lever up to increase the brightness of the instrument pane...

  • Page 173

    Map/reading lights these lights are mounted between the sun visors above the rear view mirror. Each light is turned on by pressing the button. Press the button a second time to turn the light off. The lights also come on when a door is opened or the dimmer control is turned fully upward, past the se...

  • Page 174

    Windshield wipers and washers the windshield wiper/washer control lever is located on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. For information on the rear wiper/washer, refer to “rear window fea- tures” in “understand...

  • Page 175

    Caution! • turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • in cold weather, always turn off the wiper switch and allow the wipers to return to the “park” posi- tion be...

  • Page 176

    Intermittent wiper system use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Select the delay interval by turning the end of the lever. Rotate the end of the lever upward (clockwise) to decrease the delay time and downwar...

  • Page 177

    Mist feature push down on the control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. Note: the mist feature does not activate the washer pump; therefore, no washer fluid wil...

  • Page 178

    Tilt steering column this feature allows you to tilt the steering column upward or downward. The tilt steering column lever is located on the left side of the steering column, below the turn signal lever. Push down on the lever to unlock the steering column. With one hand firmly on the steering whee...

  • Page 179

    Warning! (continued) the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Electronic speed control — if equipped when engaged, the electronic speed control takes over accelerator operations at speeds greater than 25 mph (40 km/h). The elect...

  • Page 180

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 181

    To deactivate a soft tap on the brake pedal, pushing the cancel button, or normal brake pressure while slowing the vehicle will deactivate the electronic speed control with- out erasing the set speed from memory. Pressing the on/off button or turning the ignition switch off erases the set speed from...

  • Page 182

    To decrease speed when the electronic speed control is set, you can de- crease speed by pushing the set (-) button. The speed decrement shown is dependant on the chosen speed unit of u.S. (mph) or metric (km/h): u.S. Speed (mph) • pressing the set (-) button once will result in a 1 mph decrease in s...

  • Page 183

    Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use electronic speed control in heavy traffic or on roads that are winding, icy, snow-cov...

  • Page 184

    When displayed, static grid lines will illustrate the width of the vehicle while a dashed center-line will indicate the center of the vehicle to assist with aligning to a hitch/ receiver. The static grid lines will show separate zones that will help indicate the distance to the rear of the vehicle. ...

  • Page 185

    Caution! • to avoid vehicle damage, parkview® should only be used as a parking aid. The parkview® camera is unable to view every obstacle or object in your drive path. • to avoid vehicle damage, the vehicle must be driven slowly when using parkview® to be able to stop in time when an obstacle is see...

  • Page 186

    The homelink® buttons, located on either the overhead console, headliner or sunvisor, designate the three differ- ent homelink® channels. The homelink® indicator is located above the center button. Note: homelink® is disabled when the vehicle secu- rity alarm is active. Homelink® buttons/overhead co...

  • Page 187

    Before you begin programming homelink® be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the d...

  • Page 188

    1. Cycle the ignition to the on/run position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink® button you wish to pro- gram while keeping the homelink® indicator light in view. 3. Simultaneously press and hold both the homelink® button you want to program and the hand...

  • Page 189

    Firmly press and release the “learn” or “train- ing” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the learn/train mode. Note: you have 30 seconds in which to initiate the next step after the learn button has been pressed. 6. Re...

  • Page 190

    2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink® button you wish to pro- gram while keeping the homelink® indicator light in view. 3. Simultaneously press and hold both the homelink® button you want to program and the hand-held trans- mitter button. 4. Continue to hol...

  • Page 191

    Canadian/gate operator programming for programming transmitters in canada/united states that require the transmitter signals to “time-out” after several seconds of transmission. Canadian radio frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of trans- mission ...

  • Page 192

    If you unplugged the garage door opener/device for programming, plug it back in at this time. Reprogramming a single homelink® button to reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the on/run position. 2. Press and hold the desired homelink® but...

  • Page 193

    The homelink® universal transceiver is disabled when the vehicle security alarm is active. Troubleshooting tips if you are having trouble programming homelink®, here are some of the most common solutions: • replace the battery in the original hand-held transmit- ter. • press the learn button on the ...

  • Page 194

    Warning! (continued) use a garage door opener without these safety fea- tures. Call toll-free 1–800–355–3515 or, on the internet at www.Homelink.Com for safety information or assistance. General information this device complies with fcc rules part 15 and industry canada rss-210. Operation is subject...

  • Page 195

    Power sunroof — if equipped the power sunroof switch is located on the overhead console. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location acces- sible to children. Occupants, particularly unat-...

  • Page 196

    Opening sunroof — express press the switch rearward and release it within one-half second. The sunroof and sunshade will open automati- cally from any position. The sunroof and sunshade will open fully and stop automatically. This is called “express open”. During express open operation, any movement...

  • Page 197

    Venting sunroof — express press and release the vent button within one half second and the sunroof will open to the vent position. This is called “express vent”, and it will occur regardless of sunroof position. During express vent operation, any movement of the switch will stop the sunroof. Sunshad...

  • Page 198

    For vehicles equipped with the evic the power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is turned to the lock position. Opening either front door will cancel this feature. Electrical power outlets there is a standard 12 volt (13 amp) power outlet...

  • Page 199

    Note: to ensure proper operation a mopar® knob and element must be used. Caution! • do not exceed the maximum power of 160 watts (13 amps) at 12 volts. If the 160 watt (13 amp) power rating is exceeded the fuse protecting the system will need to be replaced. • power outlets are designed for accessor...

  • Page 200

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 201

    Power inverter — if equipped a 115 volt (150 watt) ac power inverter is located on the front of the center console for added convenience. This outlet can power mobile phones, electronics and other low power devices requiring power up to 150 watts. Certain high-end video games, such as playstation3 a...

  • Page 202

    Warning! (continued) • do not touch with wet hands. • close the lid when not in use. • if this outlet is mishandled, it may cause an electric shock and failure. Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc....

  • Page 203

    Cupholders your vehicle is equipped with four cupholders. There are two illuminated cupholders located in the front. There are two cupholders located in the back for the rear passengers. Front cupholders rear cupholders 3 understanding the features of your vehicle 201.

  • Page 204

    Storage glove compartment and storage bin located on the passenger side of the instrument panel are an upper storage bin and a lower glove compartment. Storage bins 1 — upper storage bin 2 — lower glove compartment 202 understanding the features of your vehicle.

  • Page 205

    To open the lower glove compartment, pull outward on the release handle. Door storage the interior door panels are equipped with lower storage areas. Glove compartment front door storage 3 understanding the features of your vehicle 203.

  • Page 206

    Console features the floor console contains both an upper and lower storage compartment. To open the upper storage compartment, push inward on the upper handle to unlatch the upper lid and lift the lid open. Rear door storage upper storage compartment 204 understanding the features of your vehicle.

  • Page 207

    To open the lower storage compartment, lift upward on the lower handle to unlatch the lower storage compart- ment and lift the lid open. Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a...

  • Page 208

    Press in on the flashlight to release it. To operate the flashlight, press the switch once for high, twice for low, and a third time to return to off. Cargo cover the cargo area trim panels include two notches for mounting the available tonneau cover that accommo- dates the reclining rear seat. Flas...

  • Page 209

    To install the cargo cover, insert either end of the cover into one of the two notches located in the rear trim panels. With one of the cover ends installed, push inward on the opposite end and install it into the same notch location of the rear trim panel. Using the handle, pull the cover toward yo...

  • Page 210

    Warning! In a collision a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken from its mounting. Do...

  • Page 211

    Cargo tie-down loops there are four tie-downs (d-rings) installed in the cargo area for securing cargo. Warning! • cargo tie-down loops are not safe anchors for a child seat tether strap. In a sudden stop or collision a loop could pull loose and allow the child seat to come loose. A child could be b...

  • Page 212

    Warning! (continued) • place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. • do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or be...

  • Page 213

    Rear window features rear window wiper/washer the rear wiper/washer is controlled by a rotary switch located on the center portion of the control lever. The control lever is located on the right side of the steering column. Rotate the center portion of the lever upward to the first detent position f...

  • Page 214

    Note: the rear wiper operates in an intermittent mode only. Rotate the center portion of the lever past the first detent to activate the rear washer. The washer pump and the wiper will continue to operate as long as the switch is held (for a maximum of 10 seconds). Upon release, the wiper will conti...

  • Page 215

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 216

    Approximately eight turns, then move the crossbar to the desired position, keeping the crossbars perpendicular to the luggage rack side rails. Once the crossbar is in one of the seven detent positions, retighten the thumb screws to lock the crossbar into position. Note: • to help control wind noise ...

  • Page 217

    Caution! (continued) • long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle. • travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof ra...

  • Page 219: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .220 䡵 instrument cluster . . . . . . . . . . . . . . . . .221 䡵 instrument cluster descriptions . . . . .222 䡵 mini-trip computer — if equipped . . . . .236 ▫ control buttons . . . . . . . . . . . . . . . . ....

  • Page 220

    ▫ operation instructions — disc mode for cd and mp3/wma audio play, dvd – video . . . . . . .258 ▫ list button — disc mode for mp3/wma play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .263 ▫ info button — disc mode for mp3/wma play . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 221

    ▫ connecting the ipod® or external usb device . . . . . . . . . . . . . . . . . . . . . . . . . . . . .297 ▫ using this feature. . . . . . . . . . . . . . . . . . . . .298 ▫ controlling the ipod® or external usb device using radio buttons . . . . . . . . . . . . . . . . . . .299 ▫ play mode . . . . ...

  • Page 222

    Instrument panel features 1 — air outlet 5 — storage bin 9 — heated seat switch – if equipped 2 — demisters 6 — glove compartment 10 — hazard warning flasher 3 — instrument cluster 7 — climate controls 11 — esc off switch – if equipped 4 — radio 8 — power outlet 12 — heated seat switch – if equipped...

  • Page 223

    Instrument cluster 4 understanding your instrument panel 221.

  • Page 224

    Instrument cluster descriptions 1. Fuel gauge /fuel door reminder when the ignition switch is in the on/run position, the pointer will show the level of fuel remaining in the fuel tank. The fuel pump symbol points to the side of the vehicle where the fuel door is located. 2. Charging system light th...

  • Page 225

    On briefly as a bulb check. If the light does not come on during starting, have the system checked by an autho- rized dealer. 4. Oil pressure warning light this light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while drivi...

  • Page 226

    If the vehicle is driven more than 1 mile (1.6 km) with either turn signal on, a continuous chime will sound to alert you to turn the signals off. If either indicator flashes at a rapid rate, check for a defective outside light bulb. 9. High beam indicator this indicator shows that the high beam hea...

  • Page 227

    12. Tachometer the white area of the scale shows the permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 13. Engine temperature warning light this light warns of an overheated engine condi- tio...

  • Page 228

    Booster, the abs pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by ...

  • Page 229

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 15. Transmission temperature warning light this light indicates that the t...

  • Page 230

    The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. Caution! Driving with a hot engine cooling system could damage your vehicle. If ...

  • Page 231

    20. Shift lever indicator the shift lever indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. Note: you must apply the brakes before shifting from park. 21. Odometer/trip odometer reset button press this button to change the display...

  • Page 232

    Maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the tpms low tire pressure telltale. Your vehicle has also been equipped with a tpms malfunction indicator to indicate when the system is not operating properly. The tpms malfunction indicato...

  • Page 233

    Note: u.S. Federal regulations require that upon trans- fer of vehicle ownership, the seller certify to the pur- chaser the correct mileage that the vehicle has been driven. If your odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was ...

  • Page 234

    Gascap if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “gascap” message will display in the odometer display area. Tighten the fuel filler cap properly and press the trip odometer button to turn off the message. If the problem contin...

  • Page 235

    Temporarily, press and release the trip odometer button on the instrument cluster. To reset the oil change indica- tor system (after performing the scheduled maintenance), refer to the following procedure: 1. Turn the ignition switch to the on/run position (do not start the engine). 2. Fully depress...

  • Page 236

    Caution! (continued) converter damage and power loss will soon occur. Immediate service is required. Warning! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable...

  • Page 237

    (kilometers) at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected. Note: • the “esc off indicator light” and the “esc activation/malfunction indicator light” come on momentarily each time the ignition switch is turned to ...

  • Page 238

    30. Hill descent indicator — if equipped the symbol illuminates (is armed) when the 4wd lock switch is activated and the trans- mission range indicator is in low or reverse position (off-road mode). Mini-trip computer — if equipped the mini-trip computer is located in the instrument cluster and feat...

  • Page 239

    Reset button to reset the display shown, turn the ignition switch to the on position, then press and hold the reset button located on the steering wheel. The following displays can be reset or changed: • trip a • trip b trip odometer (odo) this display shows the distance traveled since the last rese...

  • Page 240

    Electronic vehicle information center (evic) — if equipped the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following: • system status • units • vehicle information warning message displays • ...

  • Page 241

    The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: menu button press and release the menu button to scroll through the main menus (fuel economy, warn- ings, timer, units, system, personal settings) or to exit sub-menus. Compass button ...

  • Page 242

    Down button press and release the down button to scroll downward through the sub-menus. When the appropriate conditions exist, the evic displays the following messages: • turn signal on (with a continuous warning chime after 1 mile (1.6 km) of distance travelled) • left front turn signal lamp out (w...

  • Page 243

    • remote start aborted — fuel low • remote start aborted — system fault • key in ignition • low tire • low tire pressure display for premium tpm system • service tpm system engine oil change indicator system — if equipped oil change required your vehicle is equipped with an engine oil change indicat...

  • Page 244

    Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary repeat this procedure. Evic functions • compass/temperature/audio • average fuel economy • distance to empty (dte) • units in • elapsed time • tire pressure monitor (tpm...

  • Page 245

    History information will be erased, and the averaging will continue from the last fuel reading before the reset. Distance to empty (dte) shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantan...

  • Page 246

    Reset all digits will change to zeros and time will start incrementing again if the ignition switch is in run or start. Display units of measure in to make your selection, press and release the select button until “english” or “metric” appears. Personal settings (customer-programmable features) this...

  • Page 247

    Auto unlock on exit when on is selected, all the vehicle’s doors will unlock when the driver’s door is opened, if the vehicle is stopped (manual transmission) or the vehicle is stopped and the transmission is in the park or neutral position (automatic transmission). Press and hold the select button ...

  • Page 248

    When exiting the vehicle. Press and hold the select button when in this display until 0, 30, 60, or 90 appears to make your selection. Key off power delay when this feature is selected the power window switches, radio, uconnect® phone, power sunroof, and power outlets will remain active for up to 10...

  • Page 249

    Automatic compass calibration this compass is self-calibrating, which eliminates the need to set the compass manually. When the vehicle is new, the compass may appear erratic and the evic will display “cal” until the compass is calibrated. You may also calibrate the compass by completing one or more...

  • Page 250

    Compass variance compass variance is the difference between magnetic north and geographic north. To compensate for the differences, the variance should be set for the zone where the vehicle is driven, per the zone map. Once properly set, the compass will automatically compensate for the differences ...

  • Page 251

    3. Press the down button until “compass variance” message and the last variance zone number displays in the evic. 4. Press and release the select button until the proper variance zone is selected according to the map. 5. Press and release the compass button to exit. Uconnect® 230 – am/fm stereo radi...

  • Page 252

    Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Press the on/volume control knob a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the ...

  • Page 253

    Phone button uconnect® phone — if equipped press this button to operate the uconnect® phone feature (if equipped). Refer to “uconnect® phone” for further details. If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with uconnect phone” message will ...

  • Page 254

    Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in am, fm or satellite (if equipped) frequencies. Tune control turn the rotary tune/scroll control knob clockwise to increase or counter...

  • Page 255

    Or turning the tune/scroll control knob within five seconds will allow the program format type to be se- lected. Many radio stations do not currently broadcast music type information. Toggle the music type button to select the following format types: program type 16-digit character dis- play no prog...

  • Page 256

    Program type 16-digit character dis- play sports sports talk talk top 40 top 40 weather weather by pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when ...

  • Page 257

    • dvd play options — selecting the dvd play options will display the following: • subtitle — repeatedly pressing select will switch subtitles to different subtitle languages that are avail- able on the disc (if equipped). • audio stream — repeatedly pressing select will switch to different audio lan...

  • Page 258

    Menu language — if equipped selecting this item will allow the user to choose the default startup dvd menu language (effective only if language supported by disc). If you want to select a language not listed, then scroll down and select ⬙ other. ⬙ enter the four-digit country code using the tune/ sc...

  • Page 259

    Aspect ratio — if equipped selecting this item allows you to choose between wide screen, pan scan, and letter box. Autoplay — if equipped when this is set to on and a dvd video is inserted, it will bypass the dvd menu screen and automatically play the movie. In some rare cases, the dvd player may no...

  • Page 260

    Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to pushbutton memory {12 am, 12 fm, and 12 satellite (if equipped) stations}. Disc button pressing the disc button will allow you to switch from ...

  • Page 261

    Prompt when to insert disc. After the radio displays ⬙ insert disc, ⬙ insert the cd into the player. Radio display will show ⬙ loading disc ⬙ when the disc is loading and “reading disc” when the radio is reading the disc. Caution! This cd player will accept 4–3/4 in (12 cm) discs only. The use of ot...

  • Page 262

    Time button (cd mode) press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff (cd mode) press and hold ff (fast forward) and the cd player will begin to fast forward until ff is released, or rw or another cd button is pressed. The rw (re...

  • Page 263

    • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙ . ⬙ and a three- character extension) • level 2: 31 (including a separator ⬙ . ⬙ and a three- character extension) multisession disc formats are supported by the radio. Multisession discs may contain combinat...

  • Page 264

    Mpeg specifi- cation sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48 wma specifi- cation sampling fre- quency (khz) bit rate (kbps) wma 44.1 an...

  • Page 265

    To increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. List button — disc mode for mp3/wma play pressing the list button will bring up a list of all folders on ...

  • Page 266

    Note: the aux device must be turned on and the device’s volume set to the proper level. If the aux audio is not loud enough, turn the device’s volume up. If the aux audio sounds distorted, turn the device’s volume down. Seek button (auxiliary mode) no function. Scan button (auxiliary mode) no functi...

  • Page 267

    Operating instructions — video entertainment system (ves™) (if equipped) refer to “video entertainment system (ves™)” for fur- ther details. Dolby® manufactured under license from dolby® laboratories. Dolby® and the double-d symbol are trademarks of dolby® laboratories. Macrovision this product inco...

  • Page 268

    Radio system in your vehicle. Sirius will supply a wel- come kit that contains general information, including how to setup your on-line listening account. For further information, call the toll-free number 888-539-7474, or visit the sirius web site at www.Sirius.Com, or at www.Siriuscanada.Ca for ca...

  • Page 269

    Bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or...

  • Page 270

    Info button pressing the info button will cycle the display informa- tion between artist, song title, and composer (if avail- able). Also, pressing and holding the info button for an additional three seconds will make the radio display the song title all of the time (press and hold again to return t...

  • Page 271

    Setup button pressing the setup button allows you to select the following items: • display sirius id number — press the audio/ select button to display the sirius id number. This number is used to activate, deactivate, or change the sirius subscription. Set/rnd button — to set the pushbutton memory ...

  • Page 272

    Uconnect® 730n/430/430n cd/dvd/hdd/nav — if equipped refer to your uconnect® supplement manual for de- tailed operating instructions. Operating instructions (voice command system) — if equipped refer to “voice command” for further details. Operating instructions (uconnect® phone) — if equipped refer...

  • Page 273

    Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 degrees) in either direction, without stopping. Turning the ...

  • Page 274

    5. To exit, press any button/knob, or wait five seconds. Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either am or fm frequencies. Tune control turn the rotary tune/scroll contro...

  • Page 275

    Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Am/fm button press the buttons to select either am or fm mode. Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, press the set/rnd button...

  • Page 276

    Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks and m...

  • Page 277

    Caution! (continued) • dual-media disc types (one side is a dvd, the other side is a cd) should not be used, and they can cause damage to the player. Eject button — ejecting a cd press the eject button to eject the cd. If you have ejected a disc and have not removed it within 10 seconds, it will be ...

  • Page 278

    Am/fm button press the button to select either am or fm mode. Set/rnd button (random play button) press this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right seek bu...

  • Page 279

    The radio uses the following limits for file systems: • maximum number of folder levels: 8 • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file ...

  • Page 280

    Use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bit rate. Mpeg specifi- cation sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56,...

  • Page 281

    To increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. Operation instructions — auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the...

  • Page 282

    Uconnect® 130 with satellite radio operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn of...

  • Page 283

    Another selection. Holding either button will bypass stations without stopping, until you release it. Voice command system (radio) — if equipped refer to “voice command” in “understanding the fea- tures of your vehicle”. Voice command button uconnect® phone — if equipped press this button to operate...

  • Page 284

    3. After adjusting the hours, press the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll con- trol knob to save time change. 5. To exit, press any button/knob or wait ...

  • Page 285

    Setting the tone, balance and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control ...

  • Page 286

    Toggle the music type button to select the following format types: program type 16-digit character dis- play no program type or un- defined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news ne...

  • Page 287

    By pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the...

  • Page 288

    You may add a second station to each pushbutton by repeating the above procedure with this exception: press the set/rnd button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored i...

  • Page 289

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 290

    Seek button press the right seek button for the next selection on the cd. Press the left seek button to return to the beginning of the current selection, or return to the beginning of the previous selection if the cd is within the first second of the current selection. Pressing and holding the seek ...

  • Page 291

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 292

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 293

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 294

    Info button — cd mode for mp3 play pressing the info button repeatedly will scroll through the following tag information: song title, artist, file name, and folder name (if available). Press the info button once more to return to ⬙ elapsed time ⬙ priority mode. Press and hold the info button for thr...

  • Page 295

    Sports, news, entertainment, and programming for chil- dren, directly from its satellites and broadcasting studios. Note: sirius service is not available in hawaii and has limited coverage in alaska. System activation sirius satellite radio service is pre-activated, and you may begin listening immed...

  • Page 296

    Selecting uconnect® (satellite) mode press the sat button until ⬙ sat ⬙ appears in the display. A cd may remain in the radio while in the satellite radio mode. Satellite antenna to ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed with...

  • Page 297

    Remain tuned to the new channel until you make another selection. Holding either button will bypass channels without stopping until you release it. Scan button pressing the scan button causes the tuner to search for the next channel, pausing for eight seconds before con- tinuing to the next. To stop...

  • Page 298

    By pressing the seek button when the music type function is active, the radio will be tuned to the next channel with the same selected music type name. If a preset button is activated while in the music type (program type) mode, the music type mode will be exited and the radio will tune to the prese...

  • Page 299

    Buttons 1 - 6 these buttons tune the radio to the channels that you commit to pushbutton memory (12 satellite stations). Operating instructions (uconnect® phone) — if equipped refer to “uconnect® phone” in “understanding the features of your vehicle”. Ipod®/usb/mp3 control — if equipped this feature...

  • Page 300

    Once the audio device is connected and synchronized to the vehicle’s ipod®/usb/mp3 control system (ipod® or external usb device may take a few minutes to connect), the audio device starts charging and is ready for use by pressing radio switches, as described below. Note: if the audio device battery ...

  • Page 301

    Controlling the ipod® or external usb device using radio buttons to get into the ipod®/usb/mp3 control mode and access a connected audio device, either press the “aux” button on the radio faceplate or press the vr button and say ⬙ usb ⬙ or ⬙ switch to usb. ⬙ once in the ipod®/usb/ mp3 control mode, ...

  • Page 302

    During play mode will jump to the next track in the list, or press the vr button and say ⬙ next or previous track. ⬙ • while a track is playing, press the info button to see the associated metadata (artist, track title, album, etc.) for that track. Pressing the info button again jumps to the next sc...

  • Page 303

    • turning it clockwise (forward) and counterclockwise (backward) scrolls through the lists, displaying the track detail on the radio display. Once the track to be played is highlighted on the radio display, press the tune control knob to select and start playing the track. Turning the tune control k...

  • Page 304

    Device, then follow the same steps to go to the desired track in that list. Not all ipod® or external usb device sub-menu levels are available on this system. • music type button: the music type button is another shortcut button to the genre listing on your audio device. Caution! • leaving the ipod®...

  • Page 305

    Device first, then it will get streamed to the uconnect® phone system. Seven devices can be paired to the uconnect® phone system, but just one can be selected and played. Selecting a different audio device 1. Press the phone button to begin. 2. After the ⬙ ready ⬙ prompt and following the beep, say ...

  • Page 306

    The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume, and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button will ...

  • Page 307

    Cd player pressing the top of the switch once will go to the next track on the cd. Pressing the bottom of the switch once will go to the beginning of the current track, or to the beginning of the previous track if it is within eight seconds after the current track begins to play. If you press the sw...

  • Page 308

    Note: if you experience difficulty in playing a particular disc, it may be damaged (e.G., scratched, reflective coat- ing removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. Radio operation and mobile pho...

  • Page 309

    Manual heating and air conditioning the manual temperature controls consist of a series of outer rotary dials and inner push knobs. Blower control rotate this control to regulate the amount of air forced through the ven- tilation system in any mode. The blower speed increases as you move the control...

  • Page 310

    Temperature control rotate this control to regulate the tem- perature of the air inside the passenger compartment. Rotating the dial left into the blue area of the scale indicates cooler temperatures, while rotating right into the red area indicates warmer temperatures. Note: if your air conditionin...

  • Page 311

    • bi-level air is directed through the panel and floor outlets. Note: for all settings, except full cold or full hot, there is a difference in temperature between the upper and lower outlets. The warmer air flows to the floor outlets. This feature gives improved comfort during sunny but cool conditi...

  • Page 312

    • recirculation control pressing the recirculation control button will put the system in recirculation mode. This can be used when outside conditions such as smoke, odors, dust, or high humidity are pres- ent. Activating recirculation will cause the led in the control button to illuminate. Note: • c...

  • Page 313

    Note: the air conditioning compressor will not engage until the engine has been running for about 10 seconds. • max a/c for maximum cooling use the a/c and recirculation buttons at the same time. • economy mode if economy mode is desired, press the a/c button to turn off the indicator light and the ...

  • Page 314

    Note: the auto position performs best for front seat occupants only. 2. Dial in the temperature you would like the system to maintain by ro- tating the temperature control knob (center knob). Once the com- fort level is selected, the system will maintain that level automatically using the heating sy...

  • Page 315

    Blower control for full automatic operation or for automatic blower operation, turn the blower knob to the auto position. In manual mode there are seven blower speeds that can be individual selected. In off position the blower will shut off. Manual operation override this system offers a full comple...

  • Page 316

    314 understanding your instrument panel.

  • Page 317

    The operator can override the auto mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions. • panel air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. Note: the center in...

  • Page 318

    • air conditioner control press this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the mode control dial. Press this but- ton a second time to turn off the air conditionin...

  • Page 319

    • most of the time, when in automatic operation, you can temporarily put the system into recirculation mode by pressing the recirculation button. However, under certain conditions, while in automatic mode, the system is blowing air out the defrost vents. When these conditions are present, and the re...

  • Page 320

    Fresh air and high blower settings. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Window fogging interior fogging on the windshield can be quickly re- moved by turning the mode selector to defrost. The defrost/floor mo...

  • Page 321

    Control setting suggestions for various weather conditions 4 understanding your instrument panel 319.

  • Page 323: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .326 ▫ manual transmission — if equipped . . . . . . .326 ▫ automatic transmission — if equipped . . . . .327 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .327 ▫ extreme cold weather (below –20°f or −...

  • Page 324

    䡵 autostick® (six-speed automatic transmission) — if equipped . . . . . . . . . .347 ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . . .348 ▫ autostick® (cvt) — if equipped . . . . . . . . .349 ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . . .350 䡵 four-wheel drive oper...

  • Page 325

    ▫ electronic stability control (esc) . . . . . . . . . .375 ▫ esc activation/malfunction indicator light and esc off indicator light . . . . . . . . . . . . . . . .379 䡵 tire safety information . . . . . . . . . . . . .380 ▫ tire markings . . . . . . . . . . . . . . . . . . . . . . . .380 ▫ tire ide...

  • Page 326

    䡵 tire rotation recommendations . . . . .403 䡵 tire pressure monitoring system (tpms) . . . . . . . . . . . . . . . . . . . . . . .404 ▫ base system . . . . . . . . . . . . . . . . . . . . . . . . .407 ▫ premium system — if equipped . . . . . . . . . . .409 ▫ general information . . . . . . . . . . ...

  • Page 327

    ▫ towing requirements . . . . . . . . . . . . . . . . . .429 ▫ towing tips . . . . . . . . . . . . . . . . . . . . . . . . .434 䡵 recreational towing (behind motorhome, etc.) . . . . . . . . . . . . . . . . . . .437 ▫ towing this vehicle behind another vehicle . . .437 5 starting and operating 325.

  • Page 328

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park, and re- move the key fob from the ignition. When leaving the ...

  • Page 329

    Automatic transmission — if equipped the shift lever must be in the park or neutral position before you can start the engine. Depress the brake pedal before shifting to any driving gear. Note: you must press the brake pedal before shifting out of park. Tip start do not press the accelerator. Turn th...

  • Page 330

    Warning! (continued) another vehicle. This type of start can be dangerous if done improperly, so follow the procedure carefully. Refer to “jump starting” in “what to do in emer- gencies” for further information. Extreme cold weather (below –20°f or −29°c) to ensure reliable starting at these tempera...

  • Page 331

    Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. The engine block heater must be plugged in at least one hour to have an...

  • Page 332

    Use each gear in numerical order, do not skip a gear. Be sure the transmission is in first gear, (not third), when starting from a standing position. Damage to the clutch can result from starting in a gear higher than first gear. Caution! • launching in any gear except 1st gear will result in excess...

  • Page 333

    Never shift into reverse until the vehicle has come to a complete stop. Note: during cold weather, until the transmission lu- bricant is warm, you may experience slightly higher shift efforts. This is normal and not harmful to the transmis- sion. Recommended shift speeds to use your manual transmiss...

  • Page 334

    Downshifting proper downshifting will improve fuel economy and prolong engine life. Caution! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released. Damage...

  • Page 335

    Note: you must press and hold the brake pedal while shifting out of park. Warning! • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. • before exiting a vehicle, always apply the parking bra...

  • Page 336

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 337

    Out of park (refer to “brake/transmission shift inter- lock system” in this section). To drive, move the shift lever from park or neutral to the drive position. The electronically-controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore,...

  • Page 338

    When parking on a level surface, you may shift the transmission into park first, and then apply the parking brake. When parking on a hill, apply the parking brake before shifting the transmission to park, otherwise the load on the transmission locking mechanism may make it diffi- cult to move the sh...

  • Page 339

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and r...

  • Page 340

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off position to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ...

  • Page 341

    Note: do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any other ...

  • Page 342

    Transmission becomes extremely hot, the “transmission temperature warning light” may illuminate and the transmission may operate differently until the transmis- sion cools down. During very cold temperatures (-4°f [-20°c] or below), transmission operation may be modified depending on engine and tran...

  • Page 343

    Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, authorized dealer service is required...

  • Page 344

    Note: engagement of the torque converter clutch is inhibited at very cold temperatures. Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into overdrive when cold. This is normal. The torque converter clutch will fu...

  • Page 345

    Gear ranges do not race the engine when shifting from park or neutral into another gear range. Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park (p) this range supplements the parki...

  • Page 346

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 347

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the shift lever. • do not leave the key fob in or near the ...

  • Page 348

    • look at the transmission gear position display and verify that it indicates the park position. • with brake pedal released, verify that the shift lever will not move out of park. Reverse (r) this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a comp...

  • Page 349

    Drive (d) this range should be used for most city and highway driving. It provides the best fuel economy. The drive position provides optimum driving characteristics under all normal operating conditions. When frequent transmission shifting occurs (such as when operating the vehicle under heavy load...

  • Page 350

    System can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations. Operation when the shift lever is in the drive position, the transmission will operate automatically, shifting between the six available ...

  • Page 351

    • if a requested downshift would cause the engine to overspeed, that shift will not occur. • avoid using speed control when autostick® is en- gaged. • transmission shifting will be more noticeable when autostick® is engaged. • the system may revert to automatic shift mode if a fault or overheat cond...

  • Page 352

    Operation note: autostick® is not available until the cvt warms up in cold weather. When the shift lever is in the drive position, autostick® is activated by moving the shift lever side-to-side. Mov- ing the shift lever to the right (+) will activate autostick® and shift up to the next higher manual...

  • Page 353

    To disengage autostick® mode, hold the shift lever to the right (+) until “d” is once again displayed in the instru- ment cluster. You can shift in or out of the autostick® mode at any time without taking your foot off the accelerator pedal. Warning! Do not downshift for additional engine braking on...

  • Page 354

    Cluster. This can be done on the fly, at any vehicle speed. To deactivate, simply pull on the switch one more time. The “4wd indicator light” will then go out. Note: refer to “electronic brake control system/ electronic stability control (esc)” in “starting and op- erating” for further information. ...

  • Page 355

    Safe and what is not. When on a trail, you should always be looking ahead for surface obstacles and changes in terrain. The key is to plan your future driving route while remembering what you are currently driving over. Caution! Never park your vehicle over dry grass or other combustible materials. ...

  • Page 356

    Driving in snow, mud and sand there is a drastic reduction in traction when driving in snow, mud or sand. The vehicle will be less responsive to steering, acceleration and braking inputs. Therefore, you should accelerate slowly, leave greater stopping distances and avoid abrupt vehicle maneuvers. Yo...

  • Page 357

    Any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck. Sand soft sand is very difficult to travel through with full tire pressure. When crossing soft sandy spots in a trail maintain your vehicle’s momentum and do not...

  • Page 358

    Before climbing a steep hill as you approach a hill consider its grade or steepness. Determine if it is too steep. Look to see what the traction is on the hill side trail. Is the trail straight up and down? What is on top and the other side? Are there ruts, rocks, branches or other obstacles on the ...

  • Page 359

    Driving down hill before driving down a steep hill you need to determine if it is too steep for a safe descent. What is the surface traction? Is the grade too steep to maintain a slow controlled descent? Are there obstacles? Is it a straight descent? Is there plenty of distance at the base of the hi...

  • Page 360

    And hill descent braking to control the descent and apply your brakes if necessary, but do not allow the tires to lock. Warning! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling th...

  • Page 361

    Caution! Water ingestion into the transaxle, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water. Water can cause permanent damage to engine, driveline or other vehicle components and your brakes will be less effective once wet and/or muddy. Before ...

  • Page 362

    Caution! Muddy waters can reduce the cooling system effec- tiveness by depositing debris onto the radiator. After driving off-road off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road, it is always a good idea to check for damage. That way you can ...

  • Page 363

    Warning! (continued) not have full braking power when you need it to prevent a collision. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. • if you experience unusual vibration after driving in mud, slush or similar conditions, check the ...

  • Page 364

    Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. Power steering fluid check checking the power steering fluid level at a define...

  • Page 365

    Parking brake before leaving the vehicle, make sure that the parking brake is fully applied. Also, be certain to leave an automatic transmission in park, or manual transmission in reverse or first gear. The parking brake lever is located in the center console. To apply the parking brake, pull the le...

  • Page 366

    Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • this light only shows that ...

  • Page 367

    Warning! (continued) • always fully apply the parking brake when leav- ing your vehicle or it may roll and cause damage or injury. Also, be certain to leave an automatic trans- mission in park, a manual transmission in re- verse or first gear. Failure to do so may cause the vehicle to roll and cause...

  • Page 368

    If either of the two hydraulic systems lose normal capa- bility, the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop. In addition, if the malfuncti...

  • Page 369

    Warning! (continued) • the abs cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. • the capabilities of an abs-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize th...

  • Page 370

    Working properly. This self-check occurs each time the vehicle is started and accelerated past 7 mph (11 km/h). Abs is activated during braking under certain road or stopping conditions. Abs-inducing conditions can in- clude ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops. Yo...

  • Page 371

    (tcs), brake assist system (bas), electronic roll mitiga- tion (erm), hill descent control (hdc), hill start assist (hsa), and electronic stability control (esc). All sys- tems work together to enhance vehicle stability and control in various driving conditions and are commonly referred to as esc. A...

  • Page 372

    Traction control system (tcs) this system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the tcs system functions si...

  • Page 373

    Warning! (continued) • the bas cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. • the capabilities of a bas-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the use...

  • Page 374

    Warning! (continued) that wheel lift or rollover may occur. Erm cannot prevent all wheel lift or roll overs, especially those that involve leaving the roadway or striking objects or other vehicles. The capabilities of an erm- equipped vehicle must never be exploited in a reck- less or dangerous mann...

  • Page 375

    Normal. When either the brake or the accelerator is released, hdc will control the vehicle back to the origi- nal set speed. Hdc is only intended for low speed off-road driving. At vehicle speeds above 31 mph (50 km/h) hdc will no longer function. If the “hdc indicator light” begins to flash this in...

  • Page 376

    • gear selection matches vehicle uphill direction (i.E., vehicle facing uphill is in forward gear; vehicle back- ing uphill is in reverse gear). Warning! There may be situations on minor hills with a loaded vehicle, or while pulling a trailer, when the system will not activate and slight rolling may...

  • Page 377

    7. Press the “esc off” switch (located in the lower switch bank below the climate controls) four times within 20 seconds. The “esc activation/malfunction indicator light” should turn on and turn off two times. 8. Rotate the steering wheel back to center and then an additional half-turn to the right....

  • Page 378

    Warning! • the electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. • esc cannot prevent accidents, including those re- sulting from excessive speed in turns, driving on ve...

  • Page 379

    Indicator light ⬙ will be illuminated. All other stability features of esc function normally. This mode is intended to be used if the vehicle is in deep snow, sand or gravel conditions and more wheel spin than esc would nor- mally allow is required to gain traction. To turn esc on again, momentarily...

  • Page 380

    Light ⬙ will illuminate and the “esc off” message will appear in the odometer. Press and release the trip odometer button located on the instrument cluster to clear this message. In this mode, esc and tcs, except for the “limited slip” feature described in the tcs section, are turned off until the v...

  • Page 381

    Esc activation/malfunction indicator light and esc off indicator light the “esc activation/malfunction indicator light” in the instrument cluster will come on when the ignition switch is cycled to the on/ run position. It should go out with the engine running. If the “esc activation/malfunction indi...

  • Page 382

    • the esc system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when esc becomes inactive following the maneuver that caused the esc activation. The “esc off indicator light” indicates the electronic stability control (esc) is partially off or full off. ...

  • Page 383

    Note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design standards. Tires designed to this standard ...

  • Page 384

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ ....Blank.... ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t or s = temporary spare tire 31 = overall diameter in inches (in) 21...

  • Page 385

    Example: service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – the maximum speed corres...

  • Page 386

    Example: maximum load – maximum load indicates the maximum load this tire is designed to carry maximum pressure – maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire tire identification number (tin) the tin may be found on one or both sides of the tire, howe...

  • Page 387

    Example: dot ma l9 abcd 0301 abcd = code used by the tire manufacturer (one to four digits) 03 = number representing the week in which the tire was manufactured (two digits) – 03 means the 3rd week 01 = number representing the year in which the tire was manufactured (two digits) – 01 means the year ...

  • Page 388

    Term definition cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period. In- flation pressure is measured in units of psi (pound...

  • Page 389

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. B-pillar location for tire and loading information placard 5 starting and operating 387.

  • Page 390

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 391

    To determine the maximum loading conditions of your vehicle, locate the statement “the combined weight of occupants and cargo should never exceed xxx lbs or xxx kg” on the tire and loading information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) ...

  • Page 392

    Note: • if your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. The follow- ing table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and num- ber and size of occupan...

  • Page 393

    5 starting and operating 391.

  • Page 394

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 395

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns t...

  • Page 396

    At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judgement when determining proper inflation. Tires may look properly inflated even when they are under- inflated. • inspect tires for signs of tire wear or visible damage. Cau...

  • Page 397

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure ...

  • Page 398

    Consult an authorized tire dealer for tire repairs and additional information. Damaged run flat tires, or run flat tires that have experienced a loss of pressure should be replaced imme- diately with another run flat tire of identical size and service description (load index and speed code). All sea...

  • Page 399

    Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). For speeds above 75 mph (120 km/h) refer to original equipment or an authorized tire dealer for recommended safe operating speeds, ...

  • Page 400

    Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare tire. Do not install more than one compact spare tire and wheel on the vehicle at any given time. Warning! Compact spares are for temporary ...

  • Page 401

    Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressures listed on your tire and loading inf...

  • Page 402

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further infor- mation. Life of t...

  • Page 403

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with...

  • Page 404

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 405

    Caution! Damage to the vehicle may result if tire chains are used. Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can...

  • Page 406

    Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold placard pressure. The tire pressure will vary with temperature by about 1 psi (7.0 kpa) for every 12°f (6.5°c). This means that when the ...

  • Page 407

    The tpms will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold placard pressure. Once the low tire pressure warn- ing (tire pressure monitoring telltale light) illuminates, you must inc...

  • Page 408

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, t...

  • Page 409

    Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. • the tpms is not a substitute for proper tire mainte- nance, and it is the driver’s responsibility to maintain correct tire pressure using an accurate tire gauge, even if un...

  • Page 410

    Audible chime will be activated when one or more of the four active road tire pressures are low. Should this occur, you should stop as soon as possible, check the inflation pressure of each tire on your vehicle, and inflate each tire to the vehicle’s recommended cold placard pressure value. The syst...

  • Page 411

    2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warn- ing limit, upon the next ignition key cycle, a chime will sound and the tire pressure monitoring telltale light and low tire message will still turn on due to the low tire. 3. However, a...

  • Page 412

    • three trigger modules (mounted in three of the four wheel wells) • various tire pressure monitoring system messages, which display in the electronic vehicle information center (evic) • tire pressure monitoring telltale light tire pressure monitoring low pressure warnings the tire pressure monitori...

  • Page 413

    The graphic display of the pressure value(s) will stop flashing, and the tire pressure monitoring light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this infor- mation. Service tpms mess...

  • Page 414

    Will be displayed instead of dashes. A system fault can occur with any of the following scenarios: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the tpm sensors. 2. Installing some form of aftermarket window tinting that affects radio wave ...

  • Page 415

    3. However, after driving the vehicle for up to 20 min- utes above 15 mph (24 km/h), the tire pressure monitoring telltale light will flash on and off for 75 seconds and then remain on solid. In addition, the evic will display a “service tpm system” mes- sage for a minimum of five seconds and then d...

  • Page 416

    The tire pressure sensors are covered under one of the following licenses: united states mrxc4n3mf9 canada 2546a-c4n3mf9 fuel requirements 2.0l and 2.4l engine this engine is designed to meet all emis- sions regulations and provide excellent fuel economy and performance when us- ing high-quality unl...

  • Page 417

    The manufacturer supports the use of reformulated gaso- line. Properly blended reformulated gasoline will pro- vide excellent performance and durability of engine and fuel system components. Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as ethanol. Fuel...

  • Page 418

    • poor engine performance. • poor cold start and cold drivability. • increased risk for fuel system component corrosion. To fix a non-ffv vehicle inadvertently fueled once with e-85 perform the following: • drain the fuel tank (see your authorized dealer). • change the engine oil and oil filter. • d...

  • Page 419

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gas is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance and damage the emissions control system. • an out-of-tune engine or certain fuel or ignition malfu...

  • Page 420

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 421

    After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s surface. Caution! • damage to the fuel system or emission control system could result from using an improper fuel tank filler c...

  • Page 422

    Warning! (continued) • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the mil to turn on. • a fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas...

  • Page 423

    Vehicle loading as required by national highway traffic safety admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or b-pillar. Vehicle certification label your vehicle has a vehicle certification label attached to the driver’s door b-pillar. The la...

  • Page 424

    Inflation pressure this is the cold tire inflation pressure for your vehicle for all loading conditions up to full gawr. Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants ...

  • Page 425

    Caution! Do not load your vehicle any heavier than the gvwr. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. Trailer towing in this section you will find safety ti...

  • Page 426

    Measure gtw is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Gross axle weight rating (gawr...

  • Page 427

    Trailer sway control the trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. Weight-carryi...

  • Page 428

    Warning! • an improperly adjusted weight distributing hitch system may reduce handling, stability, braking performance, and could result in a collision. • weight distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable recr...

  • Page 429

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/transmission frontal area maximum gtw (gross trailer wt.) maximum tongue wt. (see note) 2.0l auto/man 22 sq ft (2.04 sq m) 1,000 lbs (450 ...

  • Page 430

    Note: the trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the tire and loading information placard. Refer to “tire safety information” in “starting and operating” for further information. Trailer and ton...

  • Page 431

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “tire and loading information” placard for the maximum combine...

  • Page 432

    Warning! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may ...

  • Page 433

    Warning! (continued) • total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. Gvwr 2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitch uti- lized. Towing requirements — tires • do not attempt to tow a trailer while ...

  • Page 434

    Towing requirements — trailer brakes • do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • an electronically actuated trailer brake controller is required when towing a trailer w...

  • Page 435

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Towing requirements — trailer lights an...

  • Page 436

    Towing tips before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Manual transmission — if equipped if using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippag...

  • Page 437

    Note: using a lower gear ratio while operating the vehicle under heavy loading conditions, will improve performance and extend transmission life by reducing excessive shifting and heat buildup. This action will also provide better engine braking. If you regularly tow a trailer for more than 45 minut...

  • Page 438

    Electronic speed control — if equipped • do not use in hilly terrain or with heavy loads. • when using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. • use speed control in flat terrain and with light loads to maxim...

  • Page 439

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmission automatic transmission flat tow none • transmission in neu- tral • key in acc position not allowed dolly tow front ok (fwd only) ok (fwd only) rear not a...

  • Page 440

    Caution! • do not flat tow any vehicle equipped with an automatic transmission. Damage to the drivetrain will result. If these vehicles require towing, make sure all drive wheels are off the ground. • do not dolly tow any 4wd vehicle. Internal damage to the transmission or transfer case will occur i...

  • Page 441: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .441 䡵 if your engine overheats . . . . . . . . . . . .441 䡵 automatic transmission overheating . . . . . . . . . . . . . . . . . . . . . . .442 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . ....

  • Page 442

    ▫ jump-starting procedure . . . . . . . . . . . . . . . .468 䡵 freeing a stuck vehicle . . . . . . . . . . . . .470 䡵 shift lever override . . . . . . . . . . . . . . . .472 䡵 towing a disabled vehicle . . . . . . . . . . .474 ▫ with ignition key . . . . . . . . . . . . . . . . . . . . .475 440 what...

  • Page 443

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency...

  • Page 444

    Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the n...

  • Page 445

    Wheel and tire torque specifications proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any time a wheel has been removed and reinstalled on the vehicle the lug nuts/bolts should be torqued using a properly calibrated torque wrench. Torque speci...

  • Page 446

    After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may ...

  • Page 447

    Warning! (continued) • being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be ra...

  • Page 448

    Preparations for jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the whe...

  • Page 449

    Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • turn on the hazard warning flasher. • block the ...

  • Page 450

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. Note: refer to “tires — general information” in “start- ing and operating” for further information about the spare tire, it’s use, and operation. 1. Remove th...

  • Page 451

    2. Loosen, but do not remove, the wheel nuts by turning them to the left one turn while the wheel is still on the ground. Note: there are front and rear jacking locations on each side of the body. The front locations are outlined by two triangular cutouts on one of the flanges in the sill flange ass...

  • Page 452

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated. Jacking locations front jacking location 450 what to do in emergencies.

  • Page 453

    Do not raise the vehicle until you are sure the jack is securely engaged. 3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to th...

  • Page 454

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Caution! Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be dama...

  • Page 455

    Warning! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. Note: the wheel cover is held on the wheel by the wheel nuts. When reinstalling the original wheel, prop- erly align the wheel cover to the valve stem, place the wheel cover onto the ...

  • Page 456

    Warning! A loose tire thrown forward in a collision or hard stop could injure the occupants in the vehicle. Have the deflated (flat) tire repaired or replaced immediately. 10. Check the spare tire pressure as soon as possible. Correct the tire pressure as required. 11. After 25 miles (40 km) check t...

  • Page 457

    3. Install the five wheel lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in pe...

  • Page 458

    4. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage. Refer to “torque specifications” in this sec- tion for correct lug nut torque. 5. After 25 miles (40 km) check the lug nut torque with a torque wrench to ensure that all lug nuts are pro...

  • Page 459

    Tirefit kit components and operation using the mode select knob and hoses your tirefit kit is equipped with the following symbols to indicate the air or sealant mode. Selecting air mode push in the mode select knob (5) and turn to this position for air pump operation only. Use the black air pump hos...

  • Page 460

    Using the power button push and release the power button (4) once to turn on the tirefit kit. Push and release the power button (4) again to turn off the tirefit kit. Using the deflation button press the deflation button (2) to reduce the air pressure in the tire if it becomes over-inflated. Tirefit...

  • Page 461

    The vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • for optimum performance, make sure the valve stem on the wheel is free of debris before connecting the tirefit kit. • you can use the tirefit air pump to inflate bicycle tires. The...

  • Page 462

    Warning! (continued) • keep tirefit away from open flames or heat source. • a loose tirefit kit thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the tirefit kit in the place provided. Failure to follow these warnings can result in injuries that are ...

  • Page 463

    Kit when injecting the sealant into the deflated tire and running the air pump. Move the vehicle as necessary to place the valve stem in this position before proceed- ing. 3. Place the transmission in park (auto transmission) or in gear (manual transmission) and turn off the igni- tion. 4. Set the p...

  • Page 464

    Note: sealant may leak out through the puncture in the tire. If the sealant (white fluid) does not flow within 0 – 10 seconds through the sealant hose (6): 1. Press the power button (4) to turn off the tirefit kit. Disconnect the sealant hose (6) from the valve stem. Make sure the valve stem is free...

  • Page 465

    If the tire does not inflate to at least 26 psi (1.8 bar) pressure within 15 minutes: • the tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. Note: if the tire becomes over-inflated, press the defla- tion button to reduce the tire pressure to the recom- men...

  • Page 466

    Warning! Tirefit is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after using tirefit. Do not exceed 55 mph (90 km/h) until the tire is repaired or replaced. Failure to follow this warning can result in injuries that are serious or fatal to you, your passengers, ...

  • Page 467

    2. Disconnect the tirefit kit from the valve stem, reinstall the cap on the valve stem and unplug from 12 volt outlet. 3. Place the tirefit kit in its proper storage area in the vehicle. 4. Have the tire inspected and repaired or replaced at the earliest opportunity at an authorized dealer or tire s...

  • Page 468

    6. Verify that the cap is installed on the fitting at the end of the sealant hose (6) and return the hose to its storage area (located on the bottom of the air pump). 7. Return the tirefit kit to its storage location in the vehicle. Jump-starting procedures if your vehicle has a discharged battery i...

  • Page 469

    Preparations for jump-start the battery in your vehicle is located in the front of the engine compartment below the air intake duct. To access the battery remove the air intake duct by turning the two finger screws, located on the radiator support. Air intake finger screws positive battery post 6 wh...

  • Page 470

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 471

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Note: remove air intake before proceeding with this jump-starting procedure. Connecting the jumper cables 1. Connect the positive (+) end of the jumper cable to...

  • Page 472

    6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the dis- charged battery. 2. Disconnect the opposite end of the negative (-) jumper cable...

  • Page 473

    And reverse (with automatic transmission) or 2nd gear and reverse (with manual transmission), while gently pressing the accelerator. Use the least amount of accel- erator pedal pressure that will maintain the rocking motion, without spinning the wheels, or racing the engine. Caution! Racing the engi...

  • Page 474

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously w...

  • Page 475

    4. Turn the ignition switch to the acc or on/run position, but do not start the engine. 5. Press and maintain firm pressure on the brake pedal. 6. Insert the screwdriver or similar tool into the access port, and push and hold the override release lever forward. 7. Move the shift lever to the neutral...

  • Page 476

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial wrecker service. Towing condition wheels off the ground manual transmission automatic transmis- sion (fwd only) automatic transmis- sion 4wd flat tow none • transmission in neutral • key in a...

  • Page 477

    With ignition key automatic transmission • front wheel drive (fwd) vehicles can be towed with the front wheels elevated, or on a flatbed truck (all four wheels off the ground). • four-wheel drive (4wd) vehicles can be towed on a flatbed truck (all four wheels off the ground). If the transmission is ...

  • Page 478

    • fwd vehicles can be towed with the front wheels elevated. • fwd or 4wd vehicles can be towed on a flatbed truck (all wheels off the ground). Caution! • do not flat tow any disabled vehicle if condition is related to a clutch, transmission or driveline component. Damage to the drivetrain could resu...

  • Page 479: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 2.0l . . . . . . . . . .479 䡵 engine compartment — 2.4l . . . . . . . . . .480 䡵 onboard diagnostic system — obd ii . .481 ▫ loose fuel filler cap message . . . . . . . . . . . .481 䡵 emissions inspection and maintenance programs . . . . . . ....

  • Page 480

    ▫ automatic transmission (six-speed) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .506 ▫ automatic transmission (cvt) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .508 ▫ manual transmission — if equipped . . . . . . .510 ▫ rear drive assembly (rda) — awd/4wd mod...

  • Page 481

    Engine compartment — 2.0l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 7 maintaining your vehicle 47...

  • Page 482

    Engine compartment — 2.4l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 480 maintaining your vehicle.

  • Page 483

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 484

    Persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the mil. Resolving the problem will turn the mil light off. Emissions inspection and maintenance programs in some localities, ...

  • Page 485

    3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 486

    Available which include detailed service information for your vehicle. Refer to these service manuals before attempting any procedure yourself. Note: intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. Warning! Y...

  • Page 487

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, power steering...

  • Page 488

    Caution! (continued) pressure and an increase in oil temperature. This could damage your engine. Also, be sure the oil fill cap is replaced and tightened after adding oil. Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintena...

  • Page 489

    Caution! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the new vehicle limited warranty. Engine oil viscosity (sae grade) mopar® sae 5w-20 engine oil or equivalent pennzoil® or shell helix® is recommended for all operating tem- ...

  • Page 490

    Station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection this manufacturer’s engines have a full-flow ...

  • Page 491

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 492

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be ...

  • Page 493

    Caution! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air condi- tioning components. Such damage is not covered by the new vehicle limited warranty. Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) t...

  • Page 494

    4. Disengage the two retaining tabs that secure the filter cover to the hvac housing, and remove the cover. 5. Remove the a/c air filter by pulling it straight out of the housing. 6. Install the a/c air filter with the arrow on the filter pointing toward the floor. When installing the filter cover, ...

  • Page 495

    The application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure proper function. When performing other underhood services, t...

  • Page 496

    When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades, this will help blade performance. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperat...

  • Page 497

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips/exhaust gas” in “things to know before starting your vehicle” for further...

  • Page 498

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 499

    Cooling system warning! • when working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at any time the ignition switch is in the on position. • you or others can be badly burned by hot engin...

  • Page 500

    Cooling system — drain, flush and refill if the engine coolant (antifreeze) is dirty or contains visible sediment, have an authorized dealer clean and flush with oat coolant (antifreeze) (conforming to ms-12106). Refer to the “maintenance schedule” for the proper maintenance intervals. Note: some ve...

  • Page 501

    Caution! (continued) • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • this vehicle has not been designed for use with...

  • Page 502

    (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area whe...

  • Page 503

    Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To pre...

  • Page 504

    Long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicle is ...

  • Page 505

    • do not change the thermostat for summer or winter operation. If replacement is ever necessary, install only the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emis- sions. Brake system in order to assure ...

  • Page 506

    Note: if your vehicle is equipped with a manual trans- mission , the brake fluid reservoir supplies fluid to both the brake system and the clutch release system. The two systems are separated in the reservoir, and a leak in one system will not affect the other system. The manual transmission clutch ...

  • Page 507

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 508

    Automatic transmission (six-speed) — if equipped selection of lubricant (six-speed transmission) it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s recommended transmission fluid. Refer to “fluids, lubricants, and gen...

  • Page 509

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating cond...

  • Page 510

    Automatic transmission (cvt) — if equipped selection of lubricant (cvt) it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s recommended transmission fluid which has the special friction coefficient additives necessary ...

  • Page 511

    Use of special dyes for diagnosing fluid leaks. Avoid using transmission sealers as they may adversely affect seals. Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. F...

  • Page 512

    Manual transmission — if equipped lubricant selection use only the manufacturers recommended transmission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Fluid level check check the fluid level by removing the fill plug. The fluid level ...

  • Page 513

    Frequency of fluid change refer to the “maintenance schedule” for the proper maintenance intervals. Power transfer unit (ptu) — awd/4wd models only lubricant selection use only the manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in “maintain- ing your vehicle” for ...

  • Page 514

    What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road salt, dirt and moisture accumulation. • stone and gravel impact. • insects, tree sap and tar. • salt in the air near seacoast localities. ...

  • Page 515

    Special care • if you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • it is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open. • if you detect any stone chips or scratches...

  • Page 516

    Note: if your vehicle is equipped with dark vapor chrome wheels do not use wheel cleaners, abrasives or polishing compounds. They will permanently damage this finish and such damage is not covered by the new vehicle limited warranty. Use only mild soap and water with a soft cloth. Used on a regular ...

  • Page 517

    Interior care use mopar® total clean to clean fabric upholstery and carpeting. Use mopar® total clean to clean vinyl upholstery. Mopar® total clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small part...

  • Page 518

    To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Gl...

  • Page 519

    Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol con...

  • Page 520

    Fuses warning! • when replacing a blown fuse, always use an ap- propriate replacement fuse with the same amp rating as the original fuse. Never replace a fuse with another fuse of higher amp rating. Never replace a blown fuse with metal wires or any other material. Failure to use proper fuses may re...

  • Page 521

    Integrated power module the integrated power module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini-fuses. A label that identifies each component may be printed on the inside of the cover. Refer to “engine compartment” in “main- taini...

  • Page 522

    Cavity cartridge fuse mini-fuse description 3 10 amp red rear center brake light switch 4 10 amp red ignition switch/occupant classification module 5 15 amp lt blue battery feed for power tech 6 10 amp red power mirror/steering con- trol satellite radio/hands- free phone 7 30 amp green ignition off ...

  • Page 523

    Cavity cartridge fuse mini-fuse description 13 20 amp yellow cigar lighter 14 10 amp red instrument cluster 15 40 amp green radiator fan 16 15 amp lt blue dome lamp/sunroof/rear wiper motor 17 10 amp red wireless control module 18 40 amp green auto shutdown relay 19 20 amp yellow radio amplifiers 20...

  • Page 524

    Cavity cartridge fuse mini-fuse description 26 15 amp lt blue auto shutdown relay 27 10 amp red airbag control module 28 10 amp red airbag control module/ occupant classification mod- ule 29 hot car (no fuse required) 30 20 amp yellow heated seat – if equipped 31 10 amp red headlamp washer – if equi...

  • Page 525

    Cavity cartridge fuse mini-fuse description 36 30 amp pink headlamp/washer control/ smart glass – if equipped 37 25 amp clear diesel fuel heater – if equipped caution! • when installing the ipm cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may ...

  • Page 526

    Vehicle storage if you will not be using your vehicle for more than 21 days, you may want to take steps to preserve your battery. • disengage the mini-fuse in the power distribution center labeled iod (ignition off-draw). • or disconnect the negative cable from the battery. • anytime you store your ...

  • Page 527

    Bulb number daytime running light (drl) 3157k front park/turn signal lamp 7444na front side marker lamp 194 front fog lamp h11ll center high mounted stop lamp (chmsl) led assembly (serviced at authorized dealer) rear tail/stop lamp led assembly (serviced at authorized dealer) rear turn lamp 7440na (...

  • Page 528

    Note: these are halogen bulbs. Take care not to touch the bulb with your fingers. Body oils from your fingers could cause excessive heat buildup which reduces bulb life. Fog lamps 1. Access lamp through the lower fascia cutout. 2. Remove electrical connector from bulb. 3. Remove bulb from housing. R...

  • Page 529

    License lamps 1. Use a screw driver to gently pry against the side of the snap tab to remove the lamp from the liftgate. 2. Rotate the socket 1/4 turn counterclockwise. 3. Pull bulb from socket. Center high-mounted stoplamp this light is an led assembly. See your authorized dealer for replacement. F...

  • Page 530

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of chrysler material standard ms-12106. Engine o...

  • Page 531

    Chassis component fluid, lubricant, or genuine part automatic transmission (cvt) — if equipped we recommend you use mopar® cvtf+4® continu- ously variable transmission fluid. Automatic transmission (six-speed) — if equipped we recommend you use sk energy atf sp-4 transmis- sion fluid. Manual transmi...

  • Page 533: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .532 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .534 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 534

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 535

    Severe duty all models change engine oil at 4000 miles (6,500 km) if the vehicle is operated in a dusty and off road environment. This type of vehicle use is considered severe duty. Once a month or before a long trip: • check engine oil level • check windshield washer fluid level • check the tire in...

  • Page 536

    Maintenance chart refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 ...

  • Page 537

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 538

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 539

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 540

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 541: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .541 ▫ prepare for the appointment. . . . . . . . . . . . .541 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .541 ▫ be reasonable with requests ....

  • Page 542

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .547 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .547 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .547 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .548 540 if...

  • Page 543

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 544

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 545

    In mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has insta...

  • Page 546

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 547

    Mopar® parts mopar® fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehi...

  • Page 548

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 549

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 550

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 551: Index

    Index 10

  • Page 552

    Abs (anti-lock brake system) . . . . . . . . . . . . . . . .366 adding engine coolant (antifreeze) . . . . . . . . . . . .499 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .418 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .493 additives, fuel . . . . . . . . . ...

  • Page 553

    Fluid and filter changes . . . . . . . . . . . . . . . . . .507 fluid level check . . . . . . . . . . . . . . . . . . . . . . .507 fluid type . . . . . . . . . . . . . . . . . . . . . . . . . . . .506 gear ranges . . . . . . . . . . . . . . . . . . . . . . . . . . .335 special additives . . . . . . ...

  • Page 554

    Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .205 luggage carrier . . . . . . . . . . . . . . . . . . . . . . . .213 cargo light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .205 cargo load floor . . . . . . . . . . . . . . . . . . . . . . . . .208 cargo tie-downs ....

  • Page 555

    Connector uci . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .297 universal consumer interface (uci) . . . . . . . . . .297 console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .204 contract, service . . . . . . . . . . . . . . . . . . . . . . . . . .543 coolant (an...

  • Page 556

    Remote keyless entry (rke) . . . . . . . . . . . . . . . .30 door locks, automatic . . . . . . . . . . . . . . . . . . . . . .32 door opener, garage. . . . . . . . . . . . . . . . . . . . . . .183 downshifting . . . . . . . . . . . . . . . . . . . . . . . . . . . .332 driver’s seat back tilt . . . ....

  • Page 557

    Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . .441 temperature gauge . . . . . . . . . . . . . . . . . . . . . .227 enhanced accident response feature . . . . . . . . . . . .72 ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .415 event data recorder . . . . . ...

  • Page 558

    Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .527 clean air . . . . . . . . . . . . . . . . . . . . . . . . . . . . .414 ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .415 filler cap (gas cap) . . . . . . . . . . . . . . . . . . . . .418 gasoline . . . . . . ....

  • Page 559

    High beam/low beam select switch . . . . . . . . .169 passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169 replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .525 switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166 head restraints . . . . . . . . ...

  • Page 560

    Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . .466 key-in reminder . . . . . . . . . . . . . . . . . . . . . . . . . .14 keyless entry system (sedan) . . . . . . . . . . . . . . . . .20 key, programming . . . . . . . . . . . . . . . . . . . . . . . . .17 key, replacement . . . ...

  • Page 561

    Headlight switch . . . . . . . . . . . . . . . . . . . . . . .166 high beam . . . . . . . . . . . . . . . . . . . . . . . . . . . .169 high beam indicator . . . . . . . . . . . . . . . . . . . . .224 high beam/low beam select . . . . . . . . . . . . . . .169 instrument cluster . . . . . . . . . . . ...

  • Page 562

    Manual transaxle fluid level check . . . . . . . . . . . . . . . . . . . . . . .510 lubricant selection . . . . . . . . . . . . . . . . . . . . . .511 manual transmission . . . . . . . . . . . . . . . . . . . . . .329 fluid level check . . . . . . . . . . . . . . . . . . . . . . .510 frequency of fl...

  • Page 563

    Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .487 filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .488 filter disposal . . . . . . . . . . . . . . . . . . . . . . . . .487 identification logo . . . . . . . . . . . . . . . . . . . . . .486 materials added to...

  • Page 564

    Pretensioners seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 programmable electronic features . . . . . . . . . . . . .244 radial ply tires . . . . . . . . . . . . . . . . . . . . . . . . . .395 radiator cap (coolant pressure cap) . . . . . . . . . . .500 radio operation . ...

  • Page 565

    Roll over warning . . . . . . . . . . . . . . . . . . . . . . . . . .4 roof type carrier . . . . . . . . . . . . . . . . . . . . . . . . .213 rotation, tires . . . . . . . . . . . . . . . . . . . . . . . . . . .403 safety checks inside vehicle . . . . . . . . . . . . . . . . .101 safety checks outsi...

  • Page 566

    Sentry key programming . . . . . . . . . . . . . . . . . . . .17 sentry key replacement . . . . . . . . . . . . . . . . . . . . .16 service assistance . . . . . . . . . . . . . . . . . . . . . . . . .541 service contract . . . . . . . . . . . . . . . . . . . . . . . . . .543 service manuals . . . . ...

  • Page 567

    System, remote starting . . . . . . . . . . . . . . . . . . . . .26 tachometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225 temperature control, automatic (atc) . . . . . . . . . .311 temperature gauge, engine coolant . . . . . . . . . . . .227 tie down hooks, cargo . . . . . . . . ...

  • Page 568

    24-hour towing assistance . . . . . . . . . . . . . . . .127 disabled vehicle . . . . . . . . . . . . . . . . . . . . . . . .474 guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .427 recreational . . . . . . . . . . . . . . . . . . . . . . . . . . .437 weight . . . . . . . . . . . ....

  • Page 569

    Things you should know about your uconnect® phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133 uconnect® 130 operating instructions auxiliary mode . . . . . . . .279 operating instructions cd mode . . . . . . . . . . . .274 operating instructions radio mode . . . . . . . . . .270...

  • Page 570

    Warranty information . . . . . . . . . . . . . . . . . . . . . .544 washer adding fluid . . . . . . . . . . . . . . . . . . . . . . . . . .493 washers, windshield . . . . . . . . . . . . . . . . . . . . . . .174 washing vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .512 wheel and wheel t...

  • Page 571

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed prop- erly by trained personnel. The following must be obs...

  • Page 572

    Compass chrysler group llc o w n e r ’ s m a n u a l 20 14 c ompas s 14mk49-126-ae fifth edition printed in u.S.A. 2 0 1 4.