1. DL manuals
  2. Jeep
  3. Automobile
  4. Compass 2015
  5. Owner's Manual

Jeep Compass 2015 Owner's Manual

Other manuals for Compass 2015: Operating Information Manual, Owner's Manual

Summary of Compass 2015

  • Page 1

    Compass chrysler group llc o w n e r ’ s m a n u a l 2015 c ompas s 15mk49-126-aa first edition printed in u.S.A. 2 0 1 5.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the feat...

  • Page 5: Introduction

    Introduction contents ! Introduction . . . . . . . . . . . . . . . . . . . . . . . .4 ! Rollover warning . . . . . . . . . . . . . . . . . . .4 ! How to use this manual . . . . . . . . . . . . . .5 ! Warnings and cautions . . . . . . . . . . . . . .7 ! Vehicle identification number . . . . . . . .7 ...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million a...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owners manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss importan...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right front body vin location 8 introduct...

  • Page 11: Contents

    Things to know before starting your vehicle contents ! A word about your keys . . . . . . . . . . . . .12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .12 ▫ locking doors with a key. . . . . . . . . . . . . . . .14 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .14 ! Sentry k...

  • Page 12

    ▫ sound horn with remote key lock . . . . . . . . .22 ▫ flash lights with remote key lock/unlock . . .23 ▫ using the panic alarm . . . . . . . . . . . . . . . . . .24 ▫ programming additional transmitters. . . . . . . .25 ▫ transmitter battery replacement . . . . . . . . . . .25 ▫ general informatio...

  • Page 13

    ! Safety tips . . . . . . . . . . . . . . . . . . . . . . . . . .98 ▫ transporting passengers. . . . . . . . . . . . . . . . . .98 ▫ exhaust gas . . . . . . . . . . . . . . . . . . . . . . . . . .99 ▫ safety checks you should make inside the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 14

    A word about your keys the authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition key removal 1. Place the shift lever in...

  • Page 15

    Note: if you try to remove the key before you place the shift lever in park, the key may become trapped tem- porarily in the ignition switch cylinder. If this occurs, place the shift lever in park, rotate the key clockwise slightly, then remove the key as described above. If a malfunction occurs, th...

  • Page 16

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector. • do not leave the key fob in...

  • Page 17

    Sentry key® the sentry key® immobilizer system prevents unau- thorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys that have an embedded el...

  • Page 18

    Caution! The sentry key® immobilizer system is not compat- ible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the keys provided with your new vehicle have been programmed to the vehicle electronics....

  • Page 19

    Customer key programming if you have two valid sentry keys®, you can program new sentry keys® to the system by performing the following procedure: 1. Cut the additional sentry key® transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the igniti...

  • Page 20

    Starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be repro- grammed. General information the sentry key® system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subjec...

  • Page 21

    3. The vehicle security light in the instrument cluster will flash rapidly for approximately 16 seconds. This shows that the vehicle security alarm is arming. During this period, if a door is opened, the ignition switch is turned to on/run, or the power door locks are unlocked in any manner, the veh...

  • Page 22

    Vehicle security alarm manual override the vehicle security alarm will not arm if you lock the doors using the manual door lock plunger. Remote keyless entry (rke) — if equipped this system allows you to lock or unlock the doors and liftgate or activate the panic alarm from distances up to approxima...

  • Page 23

    To unlock the doors and liftgate push and release the unlock button on the rke transmitter once to unlock the driver’s door, or twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn ...

  • Page 24

    Note: pushing the lock button on the rke transmitter while you are inside the vehicle will activate the vehicle security alarm. Opening a door with the vehicle security alarm activated will cause the alarm to sound. Push the unlock button to deactivate the vehicle security alarm. Illuminated approac...

  • Page 25

    • for vehicles not equipped with the evic, perform the following steps: 1. Push the lock button on a programmed rke trans- mitter for at least 4 seconds, but no longer than 10 seconds. Then, push the panic button while still holding the lock button. 2. Release both buttons at the same time. 3. Test ...

  • Page 26

    • for vehicles not equipped with the evic, perform the following steps: 1. Push and hold the unlock button on a programmed rke transmitter for at least 4 seconds, but no longer than 10 seconds. Then, push and hold the lock button while still holding the unlock button. 2. Release both buttons at the ...

  • Page 27

    Programming additional transmitters refer to sentry key® “customer key programming”. If you do not have a programmed rke transmitter, contact your authorized dealer for details. Transmitter battery replacement note: perchlorate material – special handling may ap- ply. See www.Dtsc.Ca.Gov/hazardouswa...

  • Page 28

    Note: if the rke transmitter is equipped with a screw, reinstall and tighten the screw until snug. General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference...

  • Page 29

    Note: • the vehicle must be equipped with an automatic transmission to be equipped with remote start. • obstructions between the vehicle and the key fob may reduce this range. How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in pa...

  • Page 30

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted — door ajar • remote start aborted — hood ajar • remote start abor...

  • Page 31

    • the engine can be started two consecutive times (two 15-minute cycles) with the rke transmitter. However, the ignition switch must be cycled to the on/run position before you can repeat the start sequence for a third cycle. Remote start will also cancel if any of the following occur: • the engine ...

  • Page 32

    Door locks manual door locks use the manual door lock knob to lock the doors from inside the vehicle. If the lock knob is down when the door is closed, the door will lock. Make sure the keys are not inside the vehicle before closing the door. Warning! • for personal security and safety in the event ...

  • Page 33

    Caution! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. Power door locks a power door lock switch is located on the driver’s and front passenger’s door panel. Push this switch to lock or unlock t...

  • Page 34

    Auto lock doors — if equipped the auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). Auto lock doors programming the automatic door locks feature can be enabled or disabled as follows: • for veh...

  • Page 35

    Automatic unlock doors on exit the doors will unlock automatically if: • the automatic unlock doors on exit feature is en- abled. • the transmission was in gear and the vehicle speed returned to 0 mph (0 km/h). • the transmission is in neutral or park. • the driver’s door is opened. • the doors were...

  • Page 36

    Note: • if you do not hear the chime it means that the system did not enter the programming mode and you will need to repeat the procedure. • use the automatic unlock doors on exit feature in accordance with local laws. Child-protection door lock system — rear doors to provide a safer environment fo...

  • Page 37

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Note: for emergency exit with the system engaged, move the lock knob up (unlocked position), roll down the window and open the doo...

  • Page 38

    Note: • for vehicles not equipped with the electronic vehicle information center (evic), the power window switches will remain active for 45 seconds after the ignition switch is turned to the lock position. Open- ing either front door will cancel this feature. • for vehicles equipped with the evic, ...

  • Page 39

    Auto-down the driver’s door window switch has an auto-down feature. Push the window switch past the first detent, release, and the window will go down automatically. To cancel the auto-down movement, operate the switch in either the up or down direction and release the switch. Window lockout switch ...

  • Page 40

    Liftgate note: the key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate. To unlock the liftgate, insert the key into the lock and turn it to the right (manual lock models only). The liftgate can also be unlocked using the remote keyless entry (rke) tra...

  • Page 41

    • although the liftgate has no inside release mechanism, the liftgate trim panel includes an opening with a snap-in cap that provides access to release the latch in the event of an electrical system malfunction. Warning! • driving with the liftgate open can allow poisonous exhaust gases into your ve...

  • Page 42

    Important safety precautions please pay close attention to the information in this section. It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible. Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: 1. C...

  • Page 43

    8. Do not lean against the door or window. If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between you and the door and you could be injured. 9. If the air bag system in this vehicle needs to be modified to accommodate a disabled per...

  • Page 44

    Enhanced seat belt use reminder system (beltalert) beltalert is a feature intended to remind the driver and outboard front passenger (if equipped with out- board front passenger beltalert) to buckle their seat belts. The feature is active whenever the ignition switch is in the start or on/run positi...

  • Page 45

    Note: if beltalert has been deactivated, the seat belt reminder light will continue to illuminate while the driver’s or outboard front passenger’s (if equipped with beltalert) seat belt remains unbuckled. Lap/shoulder belts all seating positions in your vehicle are equipped with lap/shoulder belts. ...

  • Page 46

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. • wearing your seat belt incorrectly could make your injuries in a collision much worse. You ...

  • Page 47

    Warning! (continued) • a seat belt that is too loose will not protect you properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • a seat belt that is worn under your arm is dangerous. Your body could strike the inside surfaces o...

  • Page 48

    3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt i...

  • Page 49

    5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfort- able and not resting on your neck. The retractor will withdraw any slack in the shoulder belt. 6. To release the seat belt, push the red button on the buckle. The seat belt will automaticall...

  • Page 50

    1. Remove the mini-latch and regular latch from its stowed position in the right rear side trim panel. Mini-latch stowage routing the rear center shoulder belt 48 things to know before starting your vehicle.

  • Page 51

    Connecting mini-latch to buckle rear center seat belt buckled 2 things to know before starting your vehicle 49.

  • Page 52

    2. Grasp the mini-latch plate and pull the belt over the seat. 3. Route the shoulder belt to the inside of the right head restraint. 4. When the belt is long enough to fit, insert the mini- latch plate into the mini-buckle until you hear a “click.” 5. Sit back in seat. Slide the regular latch plate ...

  • Page 53

    9. To release the belt, push the red button on the buckle. 10. To disengage the mini-latch from the mini-buckle for storage, insert the regular latch plate into the center red slot on the mini-buckle. The seat belt will auto- matically retract to its stowed position. If necessary, slide the latch pl...

  • Page 54

    3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted. Adjustable upper shoulder belt anchorage in the driver and...

  • Page 55

    Note: the adjustable upper shoulder belt anchorage is equipped with an easy up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release but- ton. To verify the shoulder belt anchorage is latched, pull downward on the shou...

  • Page 56

    Seat belts and pregnant women we recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the seat belt across the thighs and as snug across the hips as possible. Keep the se...

  • Page 57

    For additional information, refer to “installing child restraints using the vehicle seat belt” under the “child restraints” section of this manual. The table below defines the type of feature for each seating position. If the passenger seating position is equipped with an alr and is being used for n...

  • Page 58

    Installed in a seating position that has a seat belt with this feature. Children 12 years old and under should always be properly restrained in a vehicle with a rear seat. Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can ca...

  • Page 59

    Warning! (continued) • failure to replace the seat belt assembly could increase the risk of injury in collisions. • do not use the automatic locking mode to restrain occupants who are wearing the seat belt or children who are using booster seats. The locked mode is only used to install rear-facing o...

  • Page 60

    Caution! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. Note: for more information on properly adjusting and positi...

  • Page 61

    1. Grasp the deployed ahr from the rear seat. 2. Position the hands on the top of the deployed ahr at a comfortable position. 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. Hand positioning points on ahr 2 things to know before starting your veh...

  • Page 62

    A — downward movement b — rearward movement c — final downward movement to engage locking mechanism 4. The ahr front soft foam and trim half should lock into the back decorative plastic half. Note: • if you have difficulties or problems resetting the active head restraints, see an authorized dealer....

  • Page 63

    Supplemental restraint system (srs) air bag system components your vehicle may be equipped with the following air bag system components: • occupant restraint controller (orc) • air bag warning light • steering wheel and column • instrument panel • knee impact bolsters • advanced front air bags • sup...

  • Page 64

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 65

    Advanced front air bag features the advanced front air bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the occupant restraint controller (orc), which may receive information from the front i...

  • Page 66

    Warning! (continued) • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, air bags won’t deploy at all. Always wear your seat belts even though you have air bags. Advanced front air bag ...

  • Page 67

    The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the air bags inflate to their full size. The advanced front air bags fully inflate in less time than it takes to blink your eyes. The air bags then quickly deflate while helping to ...

  • Page 68

    The sabs may help to reduce the risk of occupant injury during certain side impact and certain rollover events, in addition to the injury reduction potential provided by the seat belts and body structure. When the sab deploys, it opens the seam on the out- board side of the seatback’s trim cover. Th...

  • Page 69

    Sabics may help reduce the risk of head injury to front and rear seat outboard occupants. Sabics may reduce the risk of injuries in certain side impact and vehicle rollover events, in addition to the injury reduction poten- tial provided by the seat belts and body structure. The sabics deploy downwa...

  • Page 70

    The sabics and sabs (“side air bags”) are designed to activate in certain side impacts and certain rollover events. The occupant restraint controller (“orc”) de- termines whether the deployment of the side air bags in a particular side impact or rollover event is appropriate, based on the severity a...

  • Page 71

    Warning! (continued) • relying on the side air bags alone could lead to more severe injuries in a collision. The side air bags work with your seat belt to restrain you properly. In some collisions, side air bags won’t deploy at all. Always wear your seat belt even though you have side air bags. Note...

  • Page 72

    The side air bags will not deploy in all rollover events. The rollover sensing-system determines if a rollover event may be in progress and whether deployment is appropriate. A slower-developing event may deploy the seat belt pretensioners on both sides of the vehicle. A faster-developing event may ...

  • Page 73

    Doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. Do not drive your vehicle after the air bags have de- ployed. If you are involved in another collision, the air bags will not be in place to protect you. Warning! Deployed air bags and se...

  • Page 74

    System reset procedure in order to reset the enhanced accident response system functions after an event, the ignition switch must be changed from ignition start or on/run to ignition off. Air bag warning light the air bags must be ready to inflate for your protection in a collision. The occupant res...

  • Page 75

    While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately. • the air bag warning light does not come on during the four to eight seconds when the ignition switch is first turned to the on/run position...

  • Page 76

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 77

    Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The main purpose of an edr is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per-...

  • Page 78

    Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the united states, and every canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be pros- ecuted for ignoring it. Ch...

  • Page 79

    Before buying any restraint system, make sure that it has a label certifying that it meets all applicable safety standards. You should also make sure that you can install it in the vehicle where you will use it. Note: • for additional information, refer to www.Seatcheck.Org or call 1–866–seatcheck (...

  • Page 80

    Child size, height, weight or age recommended type of child restraint larger children children who have out-grown their forward-facing child restraint, but are too small to properly fit the vehicle’s seat belt belt positioning booster seat and the ve- hicle seat belt, seated in the rear seat of the ...

  • Page 81

    Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint. • only use a rear-facing child restraint in a vehicle with ...

  • Page 82

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • after a child restraint i...

  • Page 83

    4. Is the lap part of the seat belt as low as possible, touching the child’s thighs and not their stomach? 5. Can the child stay seated like this for the whole trip? If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the child is us...

  • Page 84

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 85

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 86

    Latch positions for installing child restraints in this vehicle 84 things to know before starting your vehicle.

  • Page 87

    Latch position table what is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use t...

  • Page 88

    Latch position table can two child restraints be attached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to install a child seat in the center positio...

  • Page 89

    Locating the latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between ...

  • Page 90

    Locating the upper tether anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the l...

  • Page 91

    Warning! Never use the same lower anchorage to attach more than one child restraint. If you are installing latch- compatible child restraints next to each other, you must use the seat belt for the center position. You can then use either the latch anchors or the vehicle’s seat belt for installing ch...

  • Page 92

    4. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 5. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tio...

  • Page 93

    Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • child restraint anchorages ar...

  • Page 94

    Lap/shoulder belt systems for installing child restraints in this vehicle 92 things to know before starting your vehicle.

  • Page 95

    Lap/shoulder belt systems what is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forwar...

  • Page 96

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 97

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the seat belt path. It should not move more than 1 inch (25.4 mm) in any ...

  • Page 98

    1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another p...

  • Page 99

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 100

    Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem. Safety tip...

  • Page 101

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 102

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 103

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 104

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 105: Contents

    Understanding the features of your vehicle contents ! Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 ▫ inside day/night mirror . . . . . . . . . . . . . . . .107 ▫ automatic dimming mirror — if equipped . . .108 ▫ outside mirror — driver side . . . . . . . . . . . .109 ▫ outside ...

  • Page 106

    ▫ commands . . . . . . . . . . . . . . . . . . . . . . . . .144 ▫ voice training . . . . . . . . . . . . . . . . . . . . . . .148 ! Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148 ▫ power seats — if equipped . . . . . . . . . . . . . .149 ▫ heated seats — if equipped . . . . . ....

  • Page 107

    ▫ windshield wiper operation . . . . . . . . . . . . .169 ▫ intermittent wiper system . . . . . . . . . . . . . . .169 ▫ windshield washers . . . . . . . . . . . . . . . . . . .169 ▫ mist feature . . . . . . . . . . . . . . . . . . . . . . . . .170 ! Tilt steering column . . . . . . . . . . . . . . ...

  • Page 108

    ▫ closing sunroof — express. . . . . . . . . . . . . . .189 ▫ closing sunroof — manual mode . . . . . . . . . .189 ▫ pinch protect feature . . . . . . . . . . . . . . . . . . .189 ▫ venting sunroof — express . . . . . . . . . . . . . .190 ▫ sunshade operation. . . . . . . . . . . . . . . . . . . .19...

  • Page 109

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicl...

  • Page 110

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activa...

  • Page 111

    Outside mirror — driver side adjust the flat outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle with your head close to the door glass. Outside mirror — passenger side adjust the convex outside mirror so you can just see the side of your vehi...

  • Page 112

    Power mirrors the power mirror control is located on the driver’s door trim panel. To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When you are finished adjusting the mirror, turn the c...

  • Page 113

    Sun visor sliding feature the sun visors may be extended out to provide more coverage of the side glass. Uconnect® phone — if equipped uconnect® phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect® phone al- lows you to dial a phone number with your mobile phone using...

  • Page 114

    Uconnect® phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The uconnect® phone is driven through your bluetooth® “hands-free profile” mobile phone. Uconnect® feature...

  • Page 115

    Voice command button actual button location may vary with the ra- dio. The individual buttons are described in the “operation” section. The uconnect® phone can be used with any hands-free profile certified bluetooth® mobile phone. See the uconnect® website for supported phones. Refer to your mobile ...

  • Page 116

    Part of the command when you are asked for it. For example, you can use the compound form voice com- mand “phonebook new entry,” or you can break the compound form command into two voice commands: “phonebook” and “new entry.” please remember, the uconnect® phone works best when you talk in a normal ...

  • Page 117

    The following are general phone to uconnect® phone pairing instructions: 1. Activate the bluetooth® on your mobile phone. 2. Push the button to begin. 3. After the “ready” prompt and the following beep, say “device pairing.” 4. When prompted, after the beep, say “pair a device” and follow the audibl...

  • Page 118

    • the system will prompt you to say the number you want to call. • for example, you can say “234-567-8901.” • the uconnect® phone will confirm the phone number and then dial. The number will appear in the display of certain radios. Call by saying a name • push the button to begin. • after the “ready...

  • Page 119

    • when prompted, enter the number designation (e.G., “home,” “work,” “mobile,” or “other”). This will allow you to store multiple numbers for each phone- book entry, if desired. • when prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding an ent...

  • Page 120

    • a maximum of 2,000 entries per phone will be down- loaded and updated every time a phone is connected to the uconnect® phone. • depending on the maximum number of entries down- loaded, there may be a short delay before the latest downloaded names can be used. Until then, if avail- able, the previo...

  • Page 121

    After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu. “phonebook edit” can be used to add another phone number to a name entry that already exists in the phone- ...

  • Page 122

    Delete/erase “all” uconnect® phonebook entries • push the button to begin. • after the “ready” prompt and the following beep, say “phonebook erase all.” • the uconnect® phone will ask you to verify that you wish to delete all the entries from the phonebook. • after confirmation, the phonebook entrie...

  • Page 123

    Phone call features the following features can be accessed through the uconnect® phone if the feature(s) are available on your mobile service plan. For example, if your mobile service plan provides three-way calling, this feature can be accessed through the uconnect® phone. Check with your mobile se...

  • Page 124

    Call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to “toggling between calls” in this section. To combine two calls, refer to “conference call” in this section. Place/retrieve a call from hold to put a call on hold, push the button until y...

  • Page 125

    There is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automati- cally. This is cell phone-dependent. To bring the call back from hold, push and hold the button until you hear a single beep. Redial • pu...

  • Page 126

    Uconnect® phone features language selection to change the language that the uconnect® phone is using: 1. Push the button to begin. 2. After the “ready” prompt and the following beep, say the name of the language you wish to switch to english, espanol, or francais. 3. Continue to follow the system pr...

  • Page 127

    Note: • the emergency number dialed is based on the country where the vehicle is purchased (911 for the u.S. And canada and 060 for mexico). The number dialed may not be applicable with the available mobile service and area. • if supported, this number may be programmable on some systems. To do this...

  • Page 128

    To do this, push the button and say “setup,” fol- lowed by “towing assistance.” when prompted say 1-800-521-2779 for u.S./canada, say 55-14-3454 for mexico city and 1-800-712-3040 for outside mexico city in mexico. Paging to learn how to page, refer to “working with automated systems.” paging works ...

  • Page 129

    Call and then push the button and say “send.” the system will prompt you to enter the name or number and say the name of the phonebook entry you wish to send. The uconnect® phone will then send the corre- sponding phone number associated with the phone- book entry, as tones over the phone. Note: • y...

  • Page 130

    Notification to inform you of your phone and network status when you are attempting to make a phone call using uconnect® phone. The status is given for network signal strength, phone battery strength, etc. Dialing using the mobile phone keypad you can dial a phone number with your mobile phone keypa...

  • Page 131

    Advanced phone connectivity transfer call to and from mobile phone the uconnect® phone allows ongoing calls to be trans- ferred from your mobile phone to the uconnect® phone without terminating the call. To transfer an ongoing call from your uconnect® phone paired mobile phone to the uconnect® phone...

  • Page 132

    Select another mobile phone this feature allows you to select and start using another phone paired with the uconnect® phone. • push the button to begin. • after the “ready” prompt and the following beep, say “setup select phone” and follow the prompts. • you can also push the button at any time whil...

  • Page 133

    Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers, the uconnect® phone voice training feature may be used. To enter this training mode, follow one of the two following proce- dures: • from outside the uconnect® phone mode (e.G., from radio...

  • Page 134

    Voice command for best performance: • adjust the rearview mirror to provide at least ½ inch (1 cm) gap between the overhead console (if equipped) and the mirror. • always wait for the beep before speaking. • speak normally without pausing, just as you would speak to a person sitting a few feet/meter...

  • Page 135

    • phonebook (downloaded and uconnect® phone lo- cal) name recognition rate is optimized when the entries are not similar. • numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred.” • you can say “o” (letter “o”) for “0” (zero). • even though international ...

  • Page 136

    Voice text reply uconnect® phone can read or send new messages on your phone. Read messages: if you receive a new text message while your phone is connected to uconnect® phone, an announcement will be made to notify you that you have a new text message. If you wish to hear the new message: 1. Push t...

  • Page 137

    List of preset messages: 1. Yes. 2. No. 3. Where are you? 4. I need more direction. 5. L o l. 6. Why? 7. I love you. 8. Call me. 9. Call me later. 10. Thanks. 11. See you in 15 minutes. 12. I am on my way. 13. I’ll be late. 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye ...

  • Page 138

    Turn voice text reply incoming announcement on/off turning the voice text reply incoming announcement off will stop the system from announcing the new incoming messages. • push the button. • after the “ready” prompt and the following beep, say “setup incoming message announcement,” you will then be ...

  • Page 139

    3 understanding the features of your vehicle 137.

  • Page 140

    138 understanding the features of your vehicle.

  • Page 141

    3 understanding the features of your vehicle 139.

  • Page 142

    Voice commands primary alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location voice commands primary alternate (s) all call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais 140 understanding ...

  • Page 143

    Voice commands primary alternate (s) help home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book voice commands primary alternate (s) previous record again redial return to main menu return or main menu select phone select...

  • Page 144

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 145

    Warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your at- tention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. When y...

  • Page 146

    At any point, if the system does not recognize one of your commands, you will be prompted to repeat it. To hear the first available menu, push the voice com- mand button and say “help” or “main menu.” commands the voice command system understands two types of commands, universal commands and local c...

  • Page 147

    • “usb” (to switch to usb mode) • “bluetooth streaming” (to switch to bluetooth® stream- ing mode) • “memo” (to switch to the memo recorder) • “system setup” (to switch to system setup) radio am to switch to the am band, say “am” or “radio am.” in this mode, you may say the following commands: • “fr...

  • Page 148

    • “previous channel” (to select the previous channel) • “list channel” (to hear a list of available channels) • “select name” (to say the name of a channel) • “menu radio” (to switch to the radio menu) • “main menu” (to switch to the main menu) disc mode to switch to the disc mode, say “disc.” in th...

  • Page 149

    Memo mode to switch to the voice recorder mode, say “memo.” in this mode, you may say the following commands: • “new memo” (to record a new memo) — during the recording, you may push the voice command button to stop recording. You proceed by say- ing one of the following commands: – “save” (to save ...

  • Page 150

    • “tutorial” • “voice training” note: keep in mind that you have to push the voice command button first and wait for the beep before speaking the “barge in” commands. Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect® voice “v...

  • Page 151

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • be sure everyone in your vehicle is in a seat and using a seat belt properl...

  • Page 152

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 153

    Heated seats — if equipped on some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. The controls for the front heated seats are located on the center instrument panel area. You can choose from high, low or off heat settings. Amber ind...

  • Page 154

    Warning! (continued) • do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface tempera- ture of the seat. Man...

  • Page 155

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 156

    Manual lumbar — if equipped the lumbar adjustment handle is located on the inboard side of the driver’s seatback. Rotate the lever downward to increase the lumbar support or rotate the lever upward to decrease the lumbar support. Driver’s seatback recline to adjust the seatback, lift the lever locat...

  • Page 157

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Head restraints head restraints are designed to reduce the risk of injury by restricti...

  • Page 158

    When ahrs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the ahr. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear imp...

  • Page 159

    Active head restraint (normal position) active head restraint (tilted position) 3 understanding the features of your vehicle 157.

  • Page 160

    Note: • the head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head re...

  • Page 161

    Folding rear seat to provide additional storage area, each rear seatback can be folded forward. Pull the strap forward to fold the rear seatback flat. To raise the seatback, pull the strap forward and lift the seatback into its upright position. Rear seat release strap folded rear seat 3 understandi...

  • Page 162

    Warning! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. Reclining rear seat — if equipped for ...

  • Page 163

    2. Move the safety latch, located outside the vehicle under the front edge of the hood, toward the center and raise the hood. Hood release lever hood safety latch location 3 understanding the features of your vehicle 161.

  • Page 164

    Lift the hood prop rod, clipped to the right side (left side facing hood) of the engine compartment to secure the hood in the open position. Place the hood prop at the location stamped into the inner hood surface. Caution! To prevent possible damage: • before closing hood, make sure the hood prop ro...

  • Page 165

    Lights multifunction lever the multifunction lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior lights, the passing lights, and the fog lights. The multifunction lever is located on the left side of the ste...

  • Page 166

    Daytime running lights — if equipped the high beam lights will come on as daytime running lights (lower intensity), whenever the ignition is on, the engine is running, the headlight switch is off, the parking brake is off, the turn signal is off, and the shift lever is in any position except park. L...

  • Page 167

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside l...

  • Page 168

    Flash-to-pass you can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will turn on the high beam headlights until the lever is released. Note: if the multifunction lever is held in the flash-to- pass position for more than 20 seconds, the high ...

  • Page 169

    Map/reading lights these lights are mounted between the sun visors above the rear view mirror. Each light is turned on by pressing the button. Press the button a second time to turn the light off. The lights also come on when a door is opened or the dimmer control is turned fully upward, past the se...

  • Page 170

    Windshield wipers and washers the windshield wiper/washer control lever is lo- cated on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. For information on the rear wiper/washer, refer to “rear window features” in “understand...

  • Page 171

    Windshield wiper operation rotate the end of the lever upward to the second detent past the intermittent settings for low-speed wiper opera- tion. Rotate the end of the lever upward to the third detent past the intermittent settings for high-speed wiper operation. Intermittent wiper system use the i...

  • Page 172

    Lever is released, and then resume the intermittent inter- val previously selected. If the lever is pulled while in the off position, the wipers will operate for two wipe cycles, then turn off. Warning! Sudden loss of visibility through the windshield could lead to a collision. You might not see oth...

  • Page 173

    Tilt steering column this feature allows you to tilt the steering column upward or downward. The tilt steering column lever is located on the left side of the steering column, below the turn signal lever. Push down on the lever to unlock the steering column. With one hand firmly on the steering whee...

  • Page 174

    Warning! (continued) the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Electronic speed control — if equipped when engaged, the electronic speed control takes over accelerator operations at speeds greater than 25 mph (40 km/h). The elect...

  • Page 175

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 176

    To deactivate a soft tap on the brake pedal, pushing the cancel button, or normal brake pressure while slowing the vehicle will deactivate the electronic speed control with- out erasing the set speed from memory. Pressing the on/off button or turning the ignition switch off erases the set speed from...

  • Page 177

    To decrease speed when the electronic speed control is set, you can de- crease speed by pushing the set (-) button. The speed decrement shown is dependant on the chosen speed unit of u.S. (mph) or metric (km/h): u.S. Speed (mph) • pressing the set (-) button once will result in a 1 mph decrease in s...

  • Page 178

    Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use electronic speed control in heavy traffic or on roads that are winding, icy, snow-cov...

  • Page 179

    When displayed, static grid lines will illustrate the width of the vehicle while a dashed center-line will indicate the center of the vehicle to assist with aligning to a hitch/ receiver. The static grid lines will show separate zones that will help indicate the distance to the rear of the vehicle. ...

  • Page 180

    Caution! • to avoid vehicle damage, parkview® should only be used as a parking aid. The parkview® camera is unable to view every obstacle or object in your drive path. • to avoid vehicle damage, the vehicle must be driven slowly when using parkview® to be able to stop in time when an obstacle is see...

  • Page 181

    Note: homelink® is disabled when the vehicle secu- rity alarm is active. Homelink® buttons/overhead consoles homelink® buttons/sunvisor/headliner 3 understanding the features of your vehicle 179.

  • Page 182

    Before you begin programming homelink® be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the d...

  • Page 183

    1. Cycle the ignition to the on/run position. 2. Place the hand-held transmitter 1 to 3 inch (3 to 8 cm) away from the homelink® button you wish to program while keeping the homelink® indicator light in view. 3. Push and hold the homelink® button you want to program while you push and hold the hand-...

  • Page 184

    5. At the garage door opener motor (in the garage), locate the “learn” or “training” button. This can usually be found where the hanging antenna wire is attached to the garage door opener/device motor. Firmly push and release the “learn” or “train- ing” button. On some garage door openers/devices th...

  • Page 185

    Programming a non-rolling code for programming garage door openers manufactured before 1995. 1. Turn the ignition switch to the on/run position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink® button you wish to program while keeping the homelink® indicator light...

  • Page 186

    3. Without releasing the button proceed with “program- ming a non-rolling code” step 2 and follow all remaining steps. Canadian/gate operator programming for programming transmitters in canada/united states that require the transmitter signals to “time-out” after several seconds of transmission. Can...

  • Page 187

    4. Watch for the homelink® indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you are programming. 5. Push and hold the programmed homelink® button and observe the indicator light. • if th...

  • Page 188

    Using homelink® to operate, push and release the programmed homelink® button. Activation will now occur for the programmed device (i.E., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The hand-held transmitter of the device may also be used at any ...

  • Page 189

    Warning! Your motorized door or gate will open and close while you are programming the universal trans- ceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” featu...

  • Page 190

    Power sunroof — if equipped the power sunroof switch is located on the overhead console. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location acces- sible to children. Occupants, particularly unat-...

  • Page 191

    Opening sunroof — express press the switch rearward and release it within one-half second. The sunroof and sunshade will open automati- cally from any position. The sunroof and sunshade will open fully and stop automatically. This is called “express open”. During express open operation, any movement...

  • Page 192

    Venting sunroof — express press and release the vent button within one half second and the sunroof will open to the vent position. This is called “express vent”, and it will occur regardless of sunroof position. During express vent operation, any movement of the switch will stop the sunroof. Sunshad...

  • Page 193

    For vehicles equipped with the evic the power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is turned to the lock position. Opening either front door will cancel this feature. Electrical power outlets there is a standard 12 volt (13 amp) power outlet...

  • Page 194

    Caution! • do not exceed the maximum power of 160 watts (13 amps) at 12 volts. If the 160 watt (13 amp) power rating is exceeded the fuse protecting the system will need to be replaced. • power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this...

  • Page 195

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 196

    Power inverter — if equipped a 115 volt (150 watt) ac power inverter is located on the front of the center console for added convenience. This outlet can power mobile phones, electronics and other low power devices requiring power up to 150 watts. Certain high-end video games, such as playstation3 a...

  • Page 197

    Warning! (continued) • do not touch with wet hands. • close the lid when not in use. • if this outlet is mishandled, it may cause an electric shock and failure. Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc....

  • Page 198

    Cupholders your vehicle is equipped with four cupholders. There are two illuminated cupholders located in the front. There are two cupholders located in the back for the rear passengers. Front cupholders rear cupholders 196 understanding the features of your vehicle.

  • Page 199

    Storage glove compartment and storage bin located on the passenger side of the instrument panel are an upper storage bin and a lower glove compartment. To open the lower glove compartment, pull outward on the release handle. Storage bins 1 — upper storage bin 2 — lower glove compartment glove compar...

  • Page 200

    Door storage the interior door panels are equipped with lower storage areas. Front door storage rear door storage 198 understanding the features of your vehicle.

  • Page 201

    Console features the floor console contains both an upper and lower storage compartment. To open the upper storage compartment, push inward on the upper handle to unlatch the upper lid and lift the lid open. To open the lower storage compartment, lift upward on the lower handle to unlatch the lower ...

  • Page 202

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. Cargo area features cargo light the light is mounted in the headliner above the cargo area to illuminate the cargo area. Carg...

  • Page 203

    Using the handle, pull the cover toward you and guide the rear cover posts into the guides located on both sides of the rear trim panel. Warning! In a collision a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store...

  • Page 204

    Removable load floor the cargo area load floor is removable and can be washed with mild soap and water. Cargo tie-down loops there are four tie-downs (d-rings) installed in the cargo area for securing cargo. Removable load floor cargo area tie-downs 202 understanding the features of your vehicle.

  • Page 205

    Warning! • cargo tie-down loops are not safe anchors for a child seat tether strap. In a sudden stop or collision a loop could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • the weight and position of cargo a...

  • Page 206

    Fold down speakers — if equipped when the liftgate is open, the speakers can swing down off the trim panel to face rearward, for tailgating and other activities. Rear window features rear window wiper/washer the rear wiper/washer is controlled by a rotary switch located on the center portion of the ...

  • Page 207

    Rotate the center portion of the lever upward to the first detent position for rear wiper operation. Note: the rear wiper operates in an intermittent mode only. Rotate the center portion of the lever past the first detent to activate the rear washer. The washer pump and the wiper will continue to op...

  • Page 208

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 209

    Approximately eight turns, then move the crossbar to the desired position, keeping the crossbars perpendicular to the luggage rack side rails. Once the crossbar is in one of the seven detent positions, retighten the thumb screws to lock the crossbar into position. Note: • to help control wind noise ...

  • Page 210

    Caution! (continued) • travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack. Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift to a load. This is especially true on large flat loads and may result in damage to th...

  • Page 211: Contents

    Understanding your instrument panel contents ! Instrument panel features . . . . . . . . . .212 ! Instrument cluster . . . . . . . . . . . . . . . . .213 ! Instrument cluster descriptions . . . . .214 ! Mini-trip computer — if equipped . . . . .228 ▫ control buttons . . . . . . . . . . . . . . . . ....

  • Page 212

    ▫ operation instructions — disc mode for cd and mp3/wma audio play, dvd – video . . .250 ▫ list button — disc mode for mp3/wma play . . . . . . . . . . . . . . . . . . . . . .254 ▫ info button — disc mode for mp3/wma play . . . . . . . . . . . . . . . . . . . . . .254 ▫ uconnect® (satellite radio) —...

  • Page 213

    ▫ using this feature. . . . . . . . . . . . . . . . . . . . .288 ▫ controlling the ipod® or external usb device using radio buttons . . . . . . . . . . . . . . . . . . . .289 ▫ play mode . . . . . . . . . . . . . . . . . . . . . . . . . .289 ▫ list or browse mode . . . . . . . . . . . . . . . . . . ...

  • Page 214

    Instrument panel features 1 — air outlet 5 — storage bin 9 — heated seat switch – if equipped 2 — demisters 6 — glove compartment 10 — hazard warning flasher 3 — instrument cluster 7 — climate controls 11 — esc off switch – if equipped 4 — radio 8 — power outlet 12 — heated seat switch – if equipped...

  • Page 215

    Instrument cluster 4 understanding your instrument panel 213.

  • Page 216

    Instrument cluster descriptions 1. Fuel gauge /fuel door reminder when the ignition switch is in the on/run position, the pointer will show the level of fuel remaining in the fuel tank. The fuel pump symbol points to the side of the vehicle where the fuel door is located. 2. Charging system light th...

  • Page 217

    On briefly as a bulb check. If the light does not come on during starting, have the system checked by an autho- rized dealer. 4. Oil pressure warning light this light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while drivi...

  • Page 218

    If the vehicle is driven more than 1 mile (1.6 km) with either turn signal on, a continuous chime will sound to alert you to turn the signals off. If either indicator flashes at a rapid rate, check for a defective outside light bulb. 9. High beam indicator this indicator shows that the high beam hea...

  • Page 219

    12. Tachometer the white area of the scale shows the permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 13. Engine temperature warning light this light warns of an overheated engine condi- tio...

  • Page 220

    In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the abs pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capac- ity in the ev...

  • Page 221

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run position. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 15. Transmission temperature warning light this light indicates that the tra...

  • Page 222

    The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. Caution! Driving with a hot engine cooling system could damage your vehicle. If ...

  • Page 223

    20. Shift lever indicator the shift lever indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. Note: you must apply the brakes before shifting from park. 21. Odometer/trip odometer reset button press this button to change the display...

  • Page 224

    Maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the tpms low tire pressure telltale. Your vehicle has also been equipped with a tpms malfunction indicator to indicate when the system is not operating properly. The tpms malfunction indicato...

  • Page 225

    23. Odometer display/trip odometer display area this display indicates the total distance the vehicle has been driven. Note: u.S. Federal regulations require that upon trans- fer of vehicle ownership, the seller certify to the pur- chaser the correct mileage that the vehicle has been driven. If your...

  • Page 226

    Gascap if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “gascap” message will display in the odometer display area. Tighten the fuel filler cap properly and press the trip odometer button to turn off the message. If the problem contin...

  • Page 227

    Oil change indicator system (after performing the sched- uled maintenance), refer to the following procedure: 1. Turn the ignition switch to the on/run position (do not start the engine). 2. Fully depress the accelerator pedal, slowly, three times within 10 seconds. 3. Turn the ignition switch to th...

  • Page 228

    Warning! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to...

  • Page 229

    • each time the ignition is turned to on/run, the esc system will be on, even if it was turned off previously. • the esc system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when esc becomes inactive following the maneuver that caused the esc activation...

  • Page 230

    Mini-trip computer — if equipped the mini-trip computer is located in the instrument cluster and features a driver-interactive trip information and temperature display. Note: the system will display the last known outside temperature when starting the vehicle and may need to be driven several minute...

  • Page 231

    Step button push the step button located on the steering wheel to scroll through sub menus (i.E., temperature, trip func- tions: odometer, trip a, trip b). Reset button to reset the display shown, turn the ignition switch to the on position, then push and hold the reset button located on the steerin...

  • Page 232

    Electronic vehicle information center (evic) — if equipped the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following: • system status • units • vehicle information warning message displays • ...

  • Page 233

    The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: menu button push and release the menu button to scroll through the main menus (fuel economy, warn- ings, timer, units, system, personal settings) or to exit submenus. Compass button pus...

  • Page 234

    When the appropriate conditions exist, the evic displays the following messages: • turn signal on (with a continuous warning chime after 1 mile (1.6 km) of distance travelled) • left front turn signal lamp out (with a single chime) • left rear turn signal lamp out (with a single chime) • right front...

  • Page 235

    • low tire • low tire pressure display for premium tpm system • service tpm system engine oil change indicator system — if equipped oil change required your vehicle is equipped with an engine oil change indicator system. The “oil change required” message will display in the evic display for approxim...

  • Page 236

    Evic functions • compass/temperature/audio • average fuel economy • distance to empty (dte) • units in • elapsed time • tire pressure monitor (tpm) • personal settings to reset the display pushing and holding the right/select arrow button once will clear the function currently being displayed. Reset...

  • Page 237

    Distance to empty (dte) shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. This is not resettable. Note: significan...

  • Page 238

    Display units of measure in to make your selection, push and release the right/ select arrow button until “us” or “metric” appears. Personal settings (customer-programmable features) this allows the driver to set and recall features when the transmission is in park (automatic transmission) or the ve...

  • Page 239

    And the transmission is in the park or neutral position (automatic transmission). Push and hold the select button when in this display until “on” or “off” appears to make your selection. Rke unlock when driver’s door 1st is selected only the driver’s door will unlock on the first push of the remote ...

  • Page 240

    Key off power delay when this feature is selected the power window switches, radio, uconnect® phone, power sunroof, and power outlets will remain active for up to 10 minutes after the ignition switch has been turned off. Opening either front vehicle door will cancel this feature. Push and hold the s...

  • Page 241

    Display “cal” until the compass is calibrated. You may also calibrate the compass by completing one or more 360–degree turns (in an area free from large metal or metallic objects) until the “cal” message displayed in the evic turns off. The compass will now function normally. Note: a good calibratio...

  • Page 242

    The compass will automatically compensate for the differ- ences and provide the most accurate compass heading. Note: magnetic materials should be kept away from the top of the right rear quarter window. This is where the compass sensor is located. 1. Turn the ignition switch on. 2. Push and hold the...

  • Page 243

    Uconnect® 230 – am/fm stereo radio and 6-disc cd/dvd changer (mp3/wma aux jack) operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on...

  • Page 244

    Seek buttons push and release the seek buttons to search for the next listenable station in am/fm mode. Push the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations witho...

  • Page 245

    Time button push the time button to alternate locations of the time and frequency display. Clock setting procedure 1. Push and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune/ scroll control knob. 3. After adjusting the hours, push the right side tune/ ...

  • Page 246

    Setting the tone, balance and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control ...

  • Page 247

    Toggle the music type button to select the following format types: program type 16-digit character display no program type or undefined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news n...

  • Page 248

    By pushing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the ...

  • Page 249

    • angle — repeatedly pressing select will change the viewing angle if supported by the dvd disc (if equipped). Note: • the available selections for each of the above entries varies depending upon the disc. • these selections can only be made while playing a dvd. • ves™ power — allows you to turn ves...

  • Page 250

    Audio language — if equipped selecting this item allows you to choose a default audio language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting # other. # enter the country code using the tune/scroll control knob to scrol...

  • Page 251

    Note: the user will have to set these defaults before loading a disc. If changes are made to these settings after a disc is loaded, changes will not be effective. Also, the defaults are effective only if the disc supports the customer-preferred settings. Am and fm buttons push the buttons to select ...

  • Page 252

    Operation instructions — disc mode for cd and mp3/wma audio play, dvd – video the radio dvd player and many dvd discs are coded by geographic region. These region codes must match for the disc to play. If the region code for the dvd disc does not match the region code for the radio dvd player, it wi...

  • Page 253

    Eject button — ejecting compact disc(s) push the eject button and the pushbutton with the corresponding number (1-6) where the cd was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show # ejecting disc # when the disc is being ejected and prompt the use...

  • Page 254

    Am or fm button (cd mode) switches the radio into the am or fm radio mode. Notes on playing mp3/wma files the radio can play mp3/wma files; however, acceptable mp3/wma file recording media and formats are limited. When writing mp3/wma files, pay attention to the following restrictions. Supported med...

  • Page 255

    Discs. The use of multisession for cd audio or mp3/ wma playback may result in longer disc loading times. If a disc contains multi-formats, such as cd audio and mp3/wma tracks, the radio will only play the mp3/ wma tracks on that disc. Supported mp3/wma file formats the radio will recognize only fil...

  • Page 256

    Playlist files are not supported. Mp3 pro files are not supported. Playback of mp3/wma files when a medium containing mp3/wma data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3/wma files. ...

  • Page 257

    Push the info button once more to return to # elapsed time # priority mode. Push and hold the info button for three seconds or more and radio will display song titles for each file. Push and hold the info button again for three seconds to return to # elapsed time # display. Operation instructions — ...

  • Page 258

    Rw/ff (auxiliary mode) no function. Set button (auxiliary mode) no function. Operating instructions (voice command system) — if equipped refer to “voice command” for further details. Operating instructions (uconnect® phone) — if equipped refer to “uconnect® phone” for further details. Operating inst...

  • Page 259

    Uconnect® (satellite radio) — if equipped satellite radio uses direct satellite-to-receiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is sirius satellite radio. This service offers over 130 channels of music, sports, news, entertainme...

  • Page 260

    Selected. Push the tune/scroll control knob and the sirius id number will display. The sirius id number display will time out in two minutes. Push any button on the radio to exit this screen. Selecting uconnect® (satellite) mode push the sat button until # sat # appears in the display. A cd may rema...

  • Page 261

    Seek buttons push and release the seek buttons to search for the next listenable station in am/fm mode. Push the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations witho...

  • Page 262

    Toggle the music type button again to select the music type. By pushing the seek button when the music type function is active, the radio will be tuned to the next channel with the same selected music type name. If a preset button is activated while in the music type (program type) mode, the music t...

  • Page 263

    Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the channels that you commit to pushbutton memory (12 satellite stations). Uconnect® 730n/430/430n cd/dvd/hdd/nav — if equipped refer to your uconnect® supplement manual for ...

  • Page 264

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 265

    3. After adjusting the hours, push the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune/ scroll control knob. Push the tune/scroll con- trol knob to save time change. 5. To exit, push any button/knob, or wait fi...

  • Page 266

    Push the rotary tune/scroll control knob a fifth time and fade will display. Turn the tune/scroll control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Am/fm button push...

  • Page 267

    Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks and m...

  • Page 268

    Caution! (continued) • dual-media disc types (one side is a dvd, the other side is a cd) should not be used, and they can cause damage to the player. Eject button — ejecting a cd push the eject button to eject the cd. If you have ejected a disc and have not removed it within 10 seconds, it will be r...

  • Page 269

    Am/fm button push the button to select either am or fm mode. Set/rnd button (random play button) push this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Push the right seek butto...

  • Page 270

    Display the file name and folder name, and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this dis- play.) maximum number of characters in file/folder names: • level 1: 12 (including ...

  • Page 271

    Mpeg specification sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 id3 tag information for artist, song title, and a...

  • Page 272

    Operation instructions — auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the user to plug in a portable device, such as an mp3 player, or ipod®, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pushing the disc/aux butto...

  • Page 273

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 274

    If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with uconnect phone” message will display on the radio screen. Phone button uconnect® phone — if equipped push this button to operate the uconnect® phone feature (if equipped). Refer to “uconnect® ...

  • Page 275

    Starting at step 2. For vehicles not equipped with satellite radio, push the setup button and then follow the above procedure, starting at step 2. Info button push the info button for an rds station (one with call letters displayed). The radio will return a radio text message broadcast from an fm st...

  • Page 276

    Push the rotary tune/scroll control knob a fifth time and fade will display. Turn the tune/scroll control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Music type button...

  • Page 277

    Program type 16-digit character display oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r&b sports sports talk talk top 40 top 40 weather weather by pushing the ...

  • Page 278

    Am/fm button push the button to select either am or fm mode. Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, push the set/rnd button. The symbol set 1 will now show in the display window. Select the button (1–6) you wish to...

  • Page 279

    Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks and m...

  • Page 280

    Caution! (continued) • dual-media disc types (one side is a dvd, the other side is a cd) should not be used, and they can cause damage to the player. Eject button — ejecting a cd push the eject button to eject the cd. If you have ejected a disc and have not removed it within 10 seconds, it will be r...

  • Page 281

    Am/fm button push the button to select either am or fm mode. Set/rnd button (random play button) push this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Push the right seek butto...

  • Page 282

    Display the file name and folder name, and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this dis- play.) maximum number of characters in file/folder names: • level 1: 12 (including ...

  • Page 283

    Mpeg specification sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 id3 tag information for artist, song title, and a...

  • Page 284

    List button — cd mode for mp3 play pushing the list button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the tune/scroll control knob. Selecting a folder by pushing the tune/scroll control knob will begin playing the files contained in that folder ...

  • Page 285

    Time button (auxiliary mode) push this button to change the display to time of day. The time of day will display for five seconds (when the ignition is off). Uconnect® (satellite radio) — if equipped satellite radio uses direct satellite-to-receiver broadcast- ing technology to provide clear digital...

  • Page 286

    To access the esn/sid, refer to the following steps: esn/sid access with the ignition switch in the on/run or acc posi- tion and the radio on, push the setup button and scroll using the tune/scroll control knob until sirius id is selected. Push the tune/scroll control knob and the sirius id number w...

  • Page 287

    Operating instructions — uconnect® (satellite) mode note: the ignition switch must be in the on/run or acc position to operate the radio. Seek buttons push and release the seek buttons to search for the next listenable station in am/fm mode. Push the right switch to seek up and the left switch to se...

  • Page 288

    Music type button pushing this button once will turn on the music type mode for five seconds. Pushing the music type button or turning the tune/scroll control knob within five seconds will allow the program format type to be se- lected. Toggle the music type button again to select the music type. By...

  • Page 289

    You may add a second channel to each pushbutton by repeating the above procedure with this exception: push the set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2. This allows a total of 12 satellite channels to be stored into pushbutton memory. The...

  • Page 290

    Connecting the ipod® or external usb device use the connection cable to connect an ipod® or external usb device to the vehicle’s usb/aux connector port which is located in the center console or glove compart- ment. Once the audio device is connected and synchronized to the vehicle’s ipod®/usb/mp3 co...

  • Page 291

    • the audio device can be controlled using the radio buttons to play, browse, and list the ipod® contents. • the audio device battery charges when plugged into the usb/aux connector (if supported by the specific audio device). Controlling the ipod® or external usb device using radio buttons to get i...

  • Page 292

    • jump backward in the current track by pushing and holding the rw button. Holding the rw button long enough will jump to the beginning of the current track. • jump forward in the current track by pushing and holding the ff >> button. • a single push backward rw or forward ff >> will jump backward o...

  • Page 293

    • rnd button (available on sales code res radio only): pushing this button toggles between shuffle on and shuffle off modes for the ipod® or external usb device, or push the vr button and say # shuffle on # or # shuffle off. # if the rnd icon is showing on the radio display, then the shuffle mode is...

  • Page 294

    In list mode, the radio preset buttons are used as shortcuts to the following lists on the ipod® or external usb device: • preset 1 – playlists • preset 2 – artists • preset 3 – albums • preset 4 – genres • preset 5 – audiobooks • preset 6 – podcasts pushing a preset button will display the current ...

  • Page 295

    Caution! (continued) • placing items on the ipod® or external usb device, or connections to the ipod® or external usb device in the vehicle, can cause damage to the device and/or to the connectors. Warning! Do not plug in or remove the ipod® or external usb device while driving. Failure to follow th...

  • Page 296

    Next track use the seek up button, or push the vr button on the radio and say “next track,” to jump to the next music track on your cellular phone. Previous track use the seek down button, or push the vr button on the radio and say “previous track,” to jump to the previous music track on your cellul...

  • Page 297

    The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume, and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button will ...

  • Page 298

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 299

    Climate controls the air conditioning and heating system is designed to make you comfortable in all types of weather. Manual heating and air conditioning the manual temperature controls consist of a series of outer rotary dials and inner push knobs. Blower control rotate this control to regulate the...

  • Page 300

    Note: if your air conditioning performance seems lower than expected, check the front of the a/c condenser located in front of the radiator for an accumulation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors may r...

  • Page 301

    • panel air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. Note: the center instrument panel outlets can be aimed so that they are directed toward the rear seat passengers for maximum airflow to the rear. • bi-level air is directed through...

  • Page 302

    Note: • the air conditioning compressor operates in mix, defrost, or a blend of these modes, even if the air conditioning (a/c) button is not pushed. This dehu- midifies the air to help dry the windshield. To improve fuel economy, use these modes only when necessary. • for information on operating t...

  • Page 303

    Automatic temperature control (atc) — if equipped the automatic temperature control system automati- cally maintains the climate in the cabin of the vehicle at the comfort levels desired by the driver and passenger. Automatic operation operation of the system is quite simple. 1. Turn the mode contro...

  • Page 304

    The recommended setting for maximum comfort for the average person is 72°f (22°c); however, this may vary. Note: • the temperature setting can be adjusted at anytime without affecting automatic operation. • pressing the air conditioning control button while in auto mode will cause the led in the con...

  • Page 305

    4 understanding your instrument panel 303.

  • Page 306

    The operator can override the auto mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions. • panel air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. Note: the center ...

  • Page 307

    • air conditioner control push this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the mode control dial. Push this but- ton a second time to turn off the air conditioning....

  • Page 308

    • most of the time, when in automatic operation, you can temporarily put the system into recirculation mode by pushing the recirculation button. However, under certain conditions, while in automatic mode, the system is blowing air out the defrost vents. When these conditions are present, and the rec...

  • Page 309

    Winter operation use of the air recirculation mode during winter months is not recommended because it may cause window fogging. Vacation storage anytime you store your vehicle, or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for about five mi...

  • Page 310

    Outside air intake make sure the air intake, located directly in front of the windshield, is free of obstructions such as leaves. Leaves collected in the air intake may reduce airflow, and if they enter the plenum, they could plug the water drains. In winter months, make sure the air intake is clear...

  • Page 311

    Control setting suggestions for various weather conditions 4 understanding your instrument panel 309.

  • Page 313: Starting And Operating

    Starting and operating contents ! Starting procedures . . . . . . . . . . . . . . . .316 ▫ manual transmission — if equipped . . . . . . .316 ▫ automatic transmission — if equipped . . . . .317 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .317 ▫ extreme cold weather (below –20°f or −...

  • Page 314

    ! Autostick® (six-speed automatic transmission) . . . . . . . . . . . . . . . . . . . . . .337 ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . . .337 ▫ autostick® (cvt) . . . . . . . . . . . . . . . . . . . . .339 ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . . .339 ! F...

  • Page 315

    ▫ esc activation/malfunction indicator light and esc off indicator light . . . . . . . . . . . .368 ! Tire safety information . . . . . . . . . . . . .369 ▫ tire markings . . . . . . . . . . . . . . . . . . . . . . . .369 ▫ tire identification number (tin). . . . . . . . . . .373 ▫ tire terminology ...

  • Page 316

    ! Tire rotation recommendations . . . . .392 ! Tire pressure monitoring system (tpms) . . . . . . . . . . . . . . . . . . . . . . .393 ▫ base system . . . . . . . . . . . . . . . . . . . . . . . . .396 ▫ premium system — if equipped . . . . . . . . . . .398 ▫ general information . . . . . . . . . . ...

  • Page 317

    ▫ towing requirements . . . . . . . . . . . . . . . . . .418 ▫ towing tips . . . . . . . . . . . . . . . . . . . . . . . . .423 ! Recreational towing (behind motorhome, etc.) . . . . . . . . . . . .425 ▫ towing this vehicle behind another vehicle . . .425 5 starting and operating 315.

  • Page 318

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park, and re- move the key fob from the ignition. When leaving the ...

  • Page 319

    Automatic transmission — if equipped the shift lever must be in the park or neutral position before you can start the engine. Depress the brake pedal before shifting to any driving gear. Note: you must press the brake pedal before shifting out of park. Tip start do not press the accelerator. Turn th...

  • Page 320

    Warning! (continued) another vehicle. This type of start can be dangerous if done improperly, so follow the procedure carefully. Refer to “jump starting” in “what to do in emer- gencies” for further information. Extreme cold weather (below –20°f or − 29°c) to ensure reliable starting at these temper...

  • Page 321

    Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. The engine block heater must be plugged in at least one hour to have an...

  • Page 322

    Use each gear in numerical order, do not skip a gear. Be sure the transmission is in first gear, (not third), when starting from a standing position. Damage to the clutch can result from starting in a gear higher than first gear. Caution! • launching in any gear except 1st gear will result in excess...

  • Page 323

    Never shift into reverse until the vehicle has come to a complete stop. Note: during cold weather, until the transmission lubri- cant is warm, you may experience slightly higher shift efforts. This is normal and not harmful to the transmission. Recommended shift speeds to use your manual transmissio...

  • Page 324

    Downshifting proper downshifting will improve fuel economy and pro- long engine life. Caution! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released. Dama...

  • Page 325

    Warning! • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something. Only shift ...

  • Page 326

    Key ignition park interlock this vehicle is equipped with a key ignition park inter- lock which requires the transmission to be in park before the ignition switch can be turned to the lock/ off (key removal) position. The key can only be re- moved from the ignition when the ignition is in the lock/o...

  • Page 327

    Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears. The transmission shift lever has only park, reverse, neutral, and drive shift positions. Manual shifts can be ma...

  • Page 328

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • your vehicle could move and injure you and others if it is not in park. Check by trying to move the shif...

  • Page 329

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 330

    The following indicators should be used to ensure that you have engaged the transmission into the park position: • when shifting into park, firmly move the shift lever all the way forward and to the left until it stops and is fully seated. • look at the transmission gear position display and verify ...

  • Page 331

    Caution! (continued) severe transmission damage. Refer to “recreational towing” in “starting and operating” and “towing a disabled vehicle” in “what to do in emergencies” for further information. Drive (d) this range should be used for most city and highway driving. It provides the smoothest upshift...

  • Page 332

    During very cold temperatures (-4°f [-20°c] or below), transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed. Normal operation will resume once the transmis- sion temperature has risen to a suitable level. Transmission limp home mode transmi...

  • Page 333

    If the transmission cannot be reset, authorized dealer service is required. Overdrive operation the automatic transmission includes an electronically controlled overdrive (sixth gear). The transmission will automatically shift into overdrive if the following con- ditions are present: • the shift lev...

  • Page 334

    Continuously variable automatic transmission (cvt) — if equipped the transmission gear position display (located in the instrument cluster) indicates the transmission gear range. You must press the brake pedal to move the shift lever out of park (refer to “brake/transmission shift inter- lock system...

  • Page 335

    Park (p) this range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use park while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. When parking on a level surface, you may shift the transmi...

  • Page 336

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and r...

  • Page 337

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off position to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ...

  • Page 338

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 339

    During sustained high speed driving or trailer towing up long grades on hot days, the auto- matic transmission oil may become too hot. If this happens, the transmission overheat indica- tor light will come on, and the vehicle will slow slightly until the transmission cools down enough to allow a ret...

  • Page 340

    Downshift the transmission to the next lower gear, while using (+) to enter autostick® mode will retain the current gear. When autostick® is active, the current transmission gear is displayed in the instrument cluster. In autostick® mode, the transmission will shift up or down when the driver moves ...

  • Page 341

    To disengage autostick® mode, hold the shift lever to the right (+) until “d” is once again displayed in the instru- ment cluster. You can shift in or out of the autostick® mode at any time without taking your foot off the accelerator pedal. Warning! Do not downshift for additional engine braking on...

  • Page 342

    In autostick® mode, the transmission will shift up or down when (+/-) is manually selected by the driver, unless an engine lugging or overspeed condition would result. It will remain in the selected gear until another upshift or downshift is chosen, except as described below: • the transmission will...

  • Page 343

    Four-wheel drive operation — if equipped this feature provides full time, on-demand, four–wheel drive (4wd). Where one or more wheels have wheel spin or if addi- tional traction is needed in sand, deep snow, or loose traction surfaces, activate the “4wd lock” switch by pulling up once and releasing....

  • Page 344

    On-road driving tips utility vehicles have higher ground clearance and a narrower track to make them capable of performing in a wide variety of off-road applications. Specific design characteristics give them a higher center of gravity than ordinary cars. An advantage of the higher ground clearance ...

  • Page 345

    Caution! Never park your vehicle over dry grass or other combustible materials. The heat from your vehicle exhaust system could cause a fire. Warning! Always wear your seat belt and firmly tie down cargo. Unsecured cargo can become projectiles in an off-road situation. When to use low (l off-road) w...

  • Page 346

    Snow in heavy snow or for additional control and traction at slower speeds, activate the 4wd lock and shift the transaxle to low (l off-road) if necessary. Do not shift to a lower gear than necessary to maintain headway. Over- revving the engine can spin the wheels and traction will be lost. If you ...

  • Page 347

    The key to driving in soft sand is using the appropriate tire pressure, accelerating slowly, avoiding abrupt ma- neuvers and maintaining the vehicle’s momentum. If you are going to be driving on large soft sandy areas or dunes, reduce your tire pressure to a minimum of 15 psi (103 kpa) to allow for ...

  • Page 348

    What is on top and the other side? Are there ruts, rocks, branches or other obstacles on the path? Can you safely recover the vehicle if something goes wrong? If every- thing looks good and you feel confident, then you should use low (l off-road) with the 4wd lock engaged and proceed with caution ma...

  • Page 349

    Driving down hill before driving down a steep hill you need to determine if it is too steep for a safe descent. What is the surface traction? Is the grade too steep to maintain a slow controlled descent? Are there obstacles? Is it a straight descent? Is there plenty of distance at the base of the hi...

  • Page 350

    To reverse. Back slowly down the hill allowing engine and hill descent braking to control the descent and apply your brakes if necessary, but do not allow the tires to lock. Warning! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn...

  • Page 351

    Bottom of the axle differentials, you should inspect all of the vehicle fluids for signs of water ingestion. Caution! Water ingestion into the transaxle, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water. Water can cause permanent damage to engine...

  • Page 352

    Caution! Muddy waters can reduce the cooling system effec- tiveness by depositing debris onto the radiator. After driving off-road off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road, it is always a good idea to check for damage. That way you can ...

  • Page 353

    Warning! (continued) not have full braking power when you need it to prevent a collision. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. • if you experience unusual vibration after driving in mud, slush or similar conditions, check the ...

  • Page 354

    Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. Power steering fluid check checking the power steering fluid level at a define...

  • Page 355

    Parking brake before leaving the vehicle, make sure that the parking brake is fully applied. Also, be certain to leave an automatic transmission in park, or manual transmission in reverse or first gear. The parking brake lever is located in the center console. To apply the parking brake, pull the le...

  • Page 356

    Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • this light only shows that ...

  • Page 357

    Warning! (continued) • always fully apply the parking brake when leav- ing your vehicle or it may roll and cause damage or injury. Also, be certain to leave an automatic trans- mission in park, a manual transmission in re- verse or first gear. Failure to do so may cause the vehicle to roll and cause...

  • Page 358

    If either of the two hydraulic systems lose normal capa- bility, the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop. In addition, if the malfuncti...

  • Page 359

    Warning! • pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • the abs cannot prevent the natural laws of phys- ics from acting on the ve...

  • Page 360

    If the “abs warning light” is on, the brake system should be serviced as soon as possible to restore the benefits of anti-lock brakes. If the “abs warning light” does not come on when the ignition switch is turned to the on position, have the bulb repaired as soon as possible. If both the “brake war...

  • Page 361

    Warning! The anti-lock brake system (abs) contains sophis- ticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This in- terference can cause possible loss of anti-lock brak- ing capability. Installation of s...

  • Page 362

    Benefit of the system, you must apply continuous brak- ing pressure during the stopping sequence (do not “pump” the brakes). Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the bas is deactivated. Warning! • the brake assist system (bas) cann...

  • Page 363

    Note: anytime the esc system is in the “full off” mode, erm is disabled. Refer to “electronic stability control (esc)” in this section for a complete explanation of the available esc modes. Warning! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance...

  • Page 364

    Mode. This is done by pressing and holding the “esc off” button for five seconds. Refer to “electronic stability control (esc)” in this section of the manual. Hdc operation can be overridden with brake application to slow the vehicle down below the hdc control speed. Conversely, if more speed is des...

  • Page 365

    Hsa activation criteria the following criteria must be met in order for hsa to activate: • vehicle must be stopped. • vehicle must be on a 7% (approximate) grade or greater hill. • gear selection matches vehicle uphill direction (i.E., vehicle facing uphill is in forward gear; vehicle back- ing uphi...

  • Page 366

    5. Release the clutch pedal (if equipped). 6. Rotate the steering wheel one-half turn to the left. 7. Press the “esc off” switch (located in the lower switch bank below the climate controls) four times within 20 seconds. The “esc activation/malfunction indicator light” should turn on and turn off tw...

  • Page 367

    Warning! • the electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. • esc cannot prevent accidents, including those re- sulting from excessive speed in turns, driving on ve...

  • Page 368

    The tcs section, has been disabled and the # esc off indicator light # will be illuminated. All other stability features of esc function normally. This mode is intended to be used if the vehicle is in deep snow, sand or gravel conditions and more wheel spin than esc would nor- mally allow is require...

  • Page 369

    Seconds when the vehicle is stopped and the engine is running. After five seconds, the # esc off indicator light # will illuminate and the “esc off” message will appear in the odometer. Press and release the trip odometer button located on the instrument cluster to clear this message. In this mode, ...

  • Page 370

    Esc activation/malfunction indicator light and esc off indicator light the “esc activation/malfunction indicator light” in the instrument cluster will come on when the ignition switch is cycled to the on/ run position. It should go out with the engine running. If the “esc activation/malfunction indi...

  • Page 371

    • each time the ignition is cycled to the on/run position, the esc system will be on even if it was cycled off previously, except for when the vehicle is started while in 4l range. • the esc system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when esc ...

  • Page 372

    Note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design standards. Tires designed to this standard ...

  • Page 373

    Tire sizing chart example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on u.S. Design standards, or % ....Blank.... % = passenger car tire based on european design standards, or lt = light truck tire based...

  • Page 374

    Example: service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – the maximum speed corres...

  • Page 375

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 376

    Example: dot ma l9 abcd 0301 01 = number representing the year in which the tire was manufactured (two digits) – 01 means the year 2001 – prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured. Example: 031 could represen...

  • Page 377

    Term definition recommended cold tire inflation pressure vehicle manufacturer’s recommended cold tire inflation pressure as shown on the tire placard. Tire placard a label permanently attached to the vehicle describing the vehicle’s loading capacity, the original equipment tire sizes and the recomme...

  • Page 378

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. Example tire placard location (b-pillar) tire and loading information placard 376 starting and operating.

  • Page 379

    3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to t...

  • Page 380

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 381

    5 starting and operating 379.

  • Page 382

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 383

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the v...

  • Page 384

    Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” cold tire infl...

  • Page 385

    Speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high-speed vehicle opera- tion. Refer to your authorized tire dealer or original equipment vehicle dealer for recommended safe operat- ing speeds, loading an...

  • Page 386

    Consult an authorized tire dealer for tire repairs and additional information. Damaged run flat tires, or run flat tires that have experienced a loss of pressure should be replaced imme- diately with another run flat tire of identical size and service description (load index and speed symbol). All s...

  • Page 387

    Snow tires some areas of the country require the use of snow tires during the winter. Snow tires can be identified by a “mountain/snowflake” symbol on the tire sidewall. If you need snow tires, select tires equivalent in size and type to the origi- nal equipment tires. Use snow tires only in sets of...

  • Page 388

    Compact spare tire — if equipped the compact spare is for temporary emergency use only. You can identify if your vehicle is equipped with a compact spare by looking at the spare tire description on the tire and loading information placard located on the driver’s side door opening or on the sidewall ...

  • Page 389

    Spare tire needs to be replaced. Since it is not the same as your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. Limited-use spare — if equipped the limited-use spare tire is for temporary emergency use only. This tire ...

  • Page 390

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping. Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Warning! Fast spinning ti...

  • Page 391

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16” (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further infor- mation. Life of tir...

  • Page 392

    Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressures. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance w...

  • Page 393

    Warning! (continued) braking of your vehicle. This can cause unpredict- able handling and stress to steering and suspen- sion components. You could lose control and have a collision resulting in serious injury or death. Use only the tire and wheel sizes with load ratings approved for your vehicle. •...

  • Page 394

    Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation a...

  • Page 395

    Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold placard pressure. The tire pressure will vary with temperature by about 1 psi (7.0 kpa) for every 12°f (6.5°c). This means that when the ...

  • Page 396

    For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 30 psi (207 kpa). If the ambient temperature is 68°f (20°c) and the measured tire pressure is 27 psi (186 kpa), a temperature drop to 20°f (-7°c) will decrease the tire pressure to approximat...

  • Page 397

    Caution! (continued) • after inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the tire pressure moni- toring sensor. Note: • the tpms is not intended to replace normal tire care and ma...

  • Page 398

    Base system this is the tpms warning indicator located in the instrument cluster. The tpms uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver mod...

  • Page 399

    Check tpms warnings the tire pressure monitoring telltale light will flash on and off for 75 seconds and remain on solid when a system fault is detected. The system fault will also sound a chime. If the ignition key is cycled, this sequence will repeat providing the system fault still exists. The ti...

  • Page 400

    4. For each subsequent ignition key cycle, a chime will sound and the tire pressure monitoring telltale light will flash on and off for 75 seconds and then remain on solid. 5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare tire, the tp...

  • Page 401

    • various tire pressure monitoring system messages, which display in the electronic vehicle information center (evic) • tire pressure monitoring telltale light tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illumi- nate in the instrument cluster and a...

  • Page 402

    The graphic display of the pressure value(s) will stop flashing, and the tire pressure monitoring light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. Service tpms messag...

  • Page 403

    Will be displayed instead of dashes. A system fault can occur with any of the following scenarios: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the tpm sensors. 2. Installing some form of aftermarket window tinting that affects radio wave ...

  • Page 404

    3. However, after driving the vehicle for up to 20 min- utes above 15 mph (24 km/h), the tire pressure monitoring telltale light will flash on and off for 75 seconds and then remain on solid. In addition, the evic will display a “service tpm system” mes- sage for a minimum of five seconds and then d...

  • Page 405

    Fuel requirements 2.0l and 2.4l engine this engine is designed to meet all emis- sions regulations and provide excellent fuel economy and performance when us- ing high-quality unleaded “regular” gaso- line having an octane rating of 87. The use of premium gasoline will not provide any benefit over r...

  • Page 406

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as ethanol. Caution! Do not use gasoline containing methanol or gaso- line containing more than 10% ethanol. Use of these blends may result in starting and drivability prob- lems, damage critical fuel system...

  • Page 407

    To fix a non-ffv vehicle inadvertently fueled once with e-85 perform the following: • drain the fuel tank (see your authorized dealer). • change the engine oil and oil filter. • disconnect and reconnect the battery to reset the engine controller memory. More extensive repairs will be required for pr...

  • Page 408

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gas is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance and damage the emissions control system. • an out-of-tune engine or certain fuel or ignition malfu...

  • Page 409

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 410

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel tank filler cap (gas cap). A poorly fitting cap could let impurities into the fuel system. • a poorly fitting gas cap may cause the “malfunc- tion indicator light (mil)” to turn on. • to avoid fu...

  • Page 411

    Warning! (continued) • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the mil to turn on. • a fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas...

  • Page 412

    Vehicle loading as required by national highway traffic safety admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or b-pillar. Vehicle certification label your vehicle has a vehicle certification label attached to the driver’s door b-pillar. The la...

  • Page 413

    Inflation pressure this is the cold tire inflation pressure for your vehicle for all loading conditions up to full gawr. Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants ...

  • Page 414

    Caution! Do not load your vehicle any heavier than the gvwr. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. Trailer towing in this section you will find safety ti...

  • Page 415

    Measure gtw is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Gross axle weight rating (gawr...

  • Page 416

    Trailer sway control the trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. Weight-carryi...

  • Page 417

    Warning! (continued) • weight distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable recreational vehicle dealer for additional information. Trailer hitch classification the following chart provides the industry standard ...

  • Page 418

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/transmission frontal area maximum gtw (gross trailer wt.) maximum tongue wt. (see note) 2.0l auto/man 22 sq ft (2.04 sq m) 1,000 lbs (450 ...

  • Page 419

    Note: the trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the tire and loading information placard. Refer to “tire safety information” in “starting and operating” for further information. Trailer and ton...

  • Page 420

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “tire and loading information” placard for the maximum combine...

  • Page 421

    Warning! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may ...

  • Page 422

    Warning! (continued) • total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. Gvwr 2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitch uti- lized. Towing requirements — tires • do not attempt to tow a trailer while ...

  • Page 423

    Towing requirements — trailer brakes • do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • an electronically actuated trailer brake controller is required when towing a trailer w...

  • Page 424

    Towing requirements — trailer lights and wiring whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for motoring safety. The trailer tow package may include a four- and seven- pin wiring harness. Use a factory approved trailer har- nes...

  • Page 425

    Towing tips before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Manual transmission — if equipped if using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippag...

  • Page 426

    Excessive shifting and heat buildup. This action will also provide better engine braking. If you regularly tow a trailer for more than 45 min- utes of continuous operation, then change the transmis- sion fluid and filter as specified for # police, taxi, fleet, or frequent trailer towing # . Refer to...

  • Page 427

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmission automatic transmission flat tow none • transmission in neutral • key in acc position not allowed dolly tow front ok (fwd only) ok (fwd only) rear not all...

  • Page 429: Contents

    What to do in emergencies contents ! Hazard warning flashers . . . . . . . . . . .429 ! If your engine overheats . . . . . . . . . . . .429 ! Wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .430 ▫ torque specifications . . . . . . . . . . . . . . . . . .430 ! Jacking a...

  • Page 430

    ! Freeing a stuck vehicle . . . . . . . . . . . . .457 ! Shift lever override . . . . . . . . . . . . . . . .458 ! Towing a disabled vehicle . . . . . . . . . . .460 ▫ with ignition key . . . . . . . . . . . . . . . . . . . . .461 428 what to do in emergencies.

  • Page 431

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency...

  • Page 432

    Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the n...

  • Page 433

    Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are proper...

  • Page 434

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to...

  • Page 435

    Jack location the jack and jack-handle are stowed under the load floor in the cargo area. Spare tire stowage the compact spare tire is stowed under the rear load floor in the cargo area. Spare tire removal lift up the load floor cover and remove the hold down. Preparations for jacking 1. Park the ve...

  • Page 436

    3. Set the parking brake. 4. Place the shift lever in park (automatic transmission) or reverse (manual transmission). 5. Turn off the ignition. 6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rea...

  • Page 437

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 438

    Note: refer to “tires — general information” in “start- ing and operating” for further information about the spare tire, it’s use, and operation. 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench and remove the wr...

  • Page 439

    Assembly. The rear location is the same but with two rectangular cutouts. For vehicles equipped with plastic trim, the plastic has been cut away to expose the jacking locations in the body. Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated. Jacking locat...

  • Page 440

    Do not raise the vehicle until you are sure the jack is securely engaged. 3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to th...

  • Page 441

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Caution! Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be dama...

  • Page 442

    7. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the lug nuts in a star pattern until each lug nut has been tightened twice. Refer to “torque specifications” in this section for proper lug nut torque. 8. Remove the wheel blocks...

  • Page 443

    3. Install the five wheel lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in pe...

  • Page 444

    Vehicles without wheel covers 1. Mount the road tire on the axle. 2. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. Warning! To avoid the risk of forcing the vehicle off the jack, do not fully tighten the lug nuts until the vehicle ...

  • Page 445

    Tire service kit components and operation using the mode select knob and hoses your tire service kit is equipped with the following symbols to indicate the air or sealant mode. Selecting air mode push in the mode select knob (5) and turn to this position for air pump operation only. Use the black ai...

  • Page 446

    Using the power button push and release the power button (4) once to turn on the tire service kit. Push and release the power button (4) again to turn off the tire service kit. Using the deflation button press the deflation button (2) to reduce the air pressure in the tire if it becomes over-inflate...

  • Page 447

    From the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • for optimum performance, make sure the valve stem on the wheel is free of debris before connecting the tire service kit. • you can use the tire service kit air pump to inflate...

  • Page 448

    Warning! (continued) • keep tire service kit away from open flames or heat source. • a loose tire service kit thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the tire service kit in the place provided. Failure to follow these warn- ings can result ...

  • Page 449

    On the ground. This will provide the best positioning of the kit when injecting the sealant into the deflated tire and running the air pump. Move the vehicle as necessary to place the valve stem in this position before proceeding. 3. Place the transmission in park (auto transmission) or in gear (man...

  • Page 450

    Note: sealant may leak out through the puncture in the tire. If the sealant (white fluid) does not flow within 0 – 10 seconds through the sealant hose (6): 1. Press the power button (4) to turn off the tire service kit. Disconnect the sealant hose (6) from the valve stem. Make sure the valve stem is...

  • Page 451

    If the tire does not inflate to at least 26 psi (1.8 bar) pressure within 15 minutes: • the tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. Note: if the tire becomes over-inflated, press the defla- tion button to reduce the tire pressure to the recom- men...

  • Page 452

    (d) drive vehicle: immediately after injecting sealant and inflating the tire, drive the vehicle 5 miles (8 km) or 10 minutes to ensure distribution of the tire service kit sealant within the tire. Do not exceed 55 mph (90 km/h). Warning! Tire service kit is not a permanent flat tire repair. Have th...

  • Page 453

    If the tire pressure is 19 psi (1.3 bar) or higher: 1. Press the power button (4) to turn on tire service kit and inflate the tire to the pressure indicated on the tire and loading information label on the driver-side door opening. Note: if the tire becomes over-inflated, press the defla- tion butto...

  • Page 454

    4. Clean any remaining sealant from the tire service kit housing. 5. Position the new sealant bottle (1) in the housing so that the sealant hose (6) aligns with the hose slot in the front of the housing. Press the bottle into the housing. An audible click will be heard indicating the bottle is locke...

  • Page 455

    Preparations for jump-start the battery in your vehicle is located in the front of the engine compartment below the air intake duct. To access the battery remove the air intake duct by turning the two finger screws, located on the radiator support. Air intake finger screws positive battery post 6 wh...

  • Page 456

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 457

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Note: remove air intake before proceeding with this jump-starting procedure. Connecting the jumper cables 1. Connect the positive (+) end of the jumper cable to...

  • Page 458

    6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the dis- charged battery. 2. Disconnect the opposite end of the negative (-) jumper cable...

  • Page 459

    Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Then shift back and forth between drive and reverse (with automatic transmission) or 2nd gear an...

  • Page 460

    Caution! (continued) • revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h) while in gear (no trans- mission shifting occurring). Warning! Fast spinning tires can be dangerous....

  • Page 461

    4. Turn the ignition switch to the acc or on/run position, but do not start the engine. 5. Press and maintain firm pressure on the brake pedal. 6. Insert the screwdriver or similar tool into the access port, and push and hold the override release lever forward. 7. Move the shift lever to the neutral...

  • Page 462

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial towing service. Towing condition wheels off the ground manual transmission 6-speed automatic (fwd only) 6-speed automatic 4wd cvt automatic transmission flat tow none • transmission in neutra...

  • Page 463

    With ignition key automatic transmission • front wheel drive (fwd) vehicles can be towed with the front wheels elevated, or on a flatbed truck (all four wheels off the ground). • four-wheel drive (4wd) vehicles can be towed on a flatbed truck (all four wheels off the ground). If the transmission is ...

  • Page 464

    Manual transmission • front wheel drive (fwd) or four-wheel drive (4wd) vehicles can be flat towed (all four wheels on the ground) with the transmission in neutral. • fwd vehicles can be towed with the front wheels elevated. • fwd or 4wd vehicles can be towed on a flatbed truck (all wheels off the g...

  • Page 465

    Caution! • do not use sling-type equipment when towing. Vehicle damage may occur. • when securing the vehicle to a flatbed truck, do not attach to front or rear suspension components. Damage to your vehicle may result from improper towing. Without the ignition key special care must be taken when the...

  • Page 467: Maintaining Your Vehicle

    Maintaining your vehicle contents ! Engine compartment — 2.0l . . . . . . . . . .467 ! Engine compartment — 2.4l . . . . . . . . . .468 ! Onboard diagnostic system — obd ii . . .469 ▫ loose fuel filler cap message . . . . . . . . . . . .469 ! Emissions inspection and maintenance programs . . . . . ....

  • Page 468

    ▫ automatic transmission (six-speed) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .494 ▫ automatic transmission (cvt) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .496 ▫ manual transmission — if equipped . . . . . . .498 ▫ rear drive assembly (rda) — awd/4wd models ...

  • Page 469

    Engine compartment — 2.0l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 7 maintaining your vehicle 46...

  • Page 470

    Engine compartment — 2.4l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 468 maintaining your vehicle.

  • Page 471

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 472

    Reset button to turn off the message. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the mil. Resolving the problem will turn the mil light off. Emissions ins...

  • Page 473

    3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 474

    Available which include detailed service information for your vehicle. Refer to these service manuals before attempting any procedure yourself. Note: intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. Warning! Y...

  • Page 475

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, power steering...

  • Page 476

    Caution! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Also, be sure the oil fill cap is replaced and tightened after adding oil. Change engine oil the oil change i...

  • Page 477

    Caution! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the new vehicle limited warranty. Engine oil viscosity (sae grade) mopar® sae 5w-20 engine oil or equivalent pennzoil® or shell helix® is recommended for all operating tem- ...

  • Page 478

    Station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection this manufacturer’s engines have a full-flow ...

  • Page 479

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 480

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked posi- tive (+) and negative (-) and are identified on the battery case. Cable clamps should b...

  • Page 481

    Warning! (continued) • the air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced technician. Caution! Do not use chemical flushes...

  • Page 482

    Warning! Do not remove the a/c air filter while the blower is operating or personal injury may result. The a/c air filter is located in the fresh air inlet behind the glove box. Perform the following procedure to re- place the filter: 1. Open the glove compartment and remove all contents. 2. Push in...

  • Page 483

    Caution! The a/c air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 7. Rotate the glove compartment door back into position. Body lubrication locks and all body pivot points...

  • Page 484

    Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Note: life expectancy of wiper blades varies depending on geographical area and frequency of use. Poor perfor- mance of blades may ...

  • Page 485

    Have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, have the exhaust system inspected e...

  • Page 486

    Caution! (continued) • damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of ...

  • Page 487

    Cooling system warning! • when working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at any time the ignition switch is in the on position. • you or others can be badly burned by hot engin...

  • Page 488

    Cooling system — drain, flush and refill note: some vehicles require special tools to add coolant properly. Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system please contact your local authorized dealer. If the engin...

  • Page 489

    Caution! (continued) • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • this vehicle has not been designed for use with...

  • Page 490

    • use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain ...

  • Page 491

    Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To pre...

  • Page 492

    The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for the coolant freeze point or replacing the engine coolant (antifreeze). Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bot...

  • Page 493

    • make sure that the coolant expansion bottle overflow hoses are not kinked or obstructed. • keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • do not change the thermostat for summer or winter operation. If replacement i...

  • Page 494

    Fluid reservoir. Fluid level can be expected to fall as the brake pads wear. The brake fluid level should be checked when the pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Note: if your vehicle is equipped with a manual trans- mission , the brake fl...

  • Page 495

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 496

    Automatic transmission (six-speed) — if equipped selection of lubricant (six-speed transmission) it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s specified transmission fluid. Refer to “fluids, lubricants, and genui...

  • Page 497

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating cond...

  • Page 498

    Automatic transmission (cvt) — if equipped selection of lubricant (cvt) it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s specified transmission fluid which has the special friction coefficient additives neces- sary ...

  • Page 499

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating cond...

  • Page 500

    Manual transmission — if equipped lubricant selection use only the manufacturers recommended transmission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Fluid level check check the fluid level by removing the fill plug. The fluid level ...

  • Page 501

    Power transfer unit (ptu) — awd/4wd models only lubricant selection use only the manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in “maintain- ing your vehicle” for further information. Fluid level check visually inspect the unit at each oil change for leakage. If ...

  • Page 502

    What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road salt, dirt and moisture accumulation. • stone and gravel impact. • insects, tree sap and tar. • salt in the air near seacoast localities. ...

  • Page 503

    Special care • if you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • it is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open. • if you detect any stone chips or scratches...

  • Page 504

    Note: if your vehicle is equipped with dark vapor or black satin chrome wheels do not use wheel cleaners, abrasives or polishing compounds. They will perma- nently damage this finish and such damage is not cov- ered by the new vehicle limited warranty. Use only mild soap and water with a soft cloth....

  • Page 505

    Interior care use mopar® total clean to clean fabric upholstery and carpeting. Use mopar® total clean to clean vinyl upholstery. Mopar® total clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small part...

  • Page 506

    To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Gl...

  • Page 507

    Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol con...

  • Page 508

    Fuses warning! • when replacing a blown fuse, always use an ap- propriate replacement fuse with the same amp rating as the original fuse. Never replace a fuse with another fuse of higher amp rating. Never replace a blown fuse with metal wires or any other material. Failure to use proper fuses may re...

  • Page 509

    Integrated power module the integrated power module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini-fuses. A label that identifies each component may be printed on the inside of the cover. Refer to “engine compartment” in “main- taini...

  • Page 510

    Cavity cartridge fuse mini-fuse description 4 10 amp red ignition switch/occupant classification module 5 15 amp lt blue battery feed for power tech 6 10 amp red power mirror/steering control satellite radio/hands-free phone 7 30 amp green ignition off draw 8 30 amp green ignition off draw 9 40 amp ...

  • Page 511

    Cavity cartridge fuse mini-fuse description 18 40 amp green auto shutdown relay 19 20 amp yellow radio amplifiers 20 15 amp lt blue radio 21 10 amp red intrusion module/siren – if equipped 22 10 amp red heating, ac/compass 23 15 amp lt blue auto shutdown relay 24 15 amp lt blue power sunroof – if eq...

  • Page 512

    Cavity cartridge fuse mini-fuse description 32 30 amp pink auto shutdown relay 33 10 amp red j1962 conn/powertrain control module 34 30 amp pink antilock brakevalve 35 40 amp green antilock brake pump 36 30 amp pink headlamp/washer control/smart glass – if equipped caution! • when installing the ipm...

  • Page 513

    Vehicle storage if you will not be using your vehicle for more than 21 days, you may want to take steps to preserve your battery. • disengage the mini-fuse in the power distribution center labeled iod (ignition off-draw). • or disconnect the negative cable from the battery. • anytime you store your ...

  • Page 514

    Bulb number premium front park lamp 3157k front park/turn signal lamp 7444na front side marker lamp 194 front fog lamp h11ll center high mounted stop lamp (chmsl) led assembly (serviced at authorized dealer) rear tail/stop lamp led assembly (serviced at authorized dealer) rear turn lamp 7440na (wy21...

  • Page 515

    4. Twist the bulb to the left. 5. Pull bulb outward from assembly. Note: these are halogen bulbs. Take care not to touch the bulb with your fingers. Body oils from your fingers could cause excessive heat buildup which reduces bulb life. Fog lamps 1. Access lamp through the lower fascia cutout. 2. Re...

  • Page 516

    License lamps 1. Use a screw driver to gently pry against the side of the snap tab to remove the lamp from the liftgate. 2. Rotate the socket 1/4 turn counterclockwise. 3. Pull bulb from socket. Center high-mounted stoplamp this light is an led assembly. See your authorized dealer for replacement. F...

  • Page 517

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the require- ments of chrysler material standard ms-12106. Engine...

  • Page 518

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 519

    Chassis component fluid, lubricant, or genuine part automatic transmission (cvt) — if equipped use only mopar® cvtf+4® continuously variable transmission fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Automatic transmission (six-spe...

  • Page 521: Maintenance Schedules

    Maintenance schedules contents ! Maintenance schedule . . . . . . . . . . . . .520 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .522 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 522

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 523

    Severe duty all models change engine oil at 4000 miles (6,500 km) if the vehicle is operated in a dusty and off road environment. This type of vehicle use is considered severe duty. Once a month or before a long trip: • check engine oil level • check windshield washer fluid level • check the tire in...

  • Page 524

    Maintenance chart refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 1...

  • Page 525

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 526

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 527

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 528

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 529: Contents

    If you need consumer assistance contents ! Suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . .529 ▫ prepare for the appointment. . . . . . . . . . . . .529 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .529 ▫ be reasonable with requests . . . . ....

  • Page 530

    ! Publication order forms . . . . . . . . . . . .534 ! Department of transportation uniform tire quality grades . . . . . . . .535 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .535 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .536 ▫ temperature grades. . . . . . . ...

  • Page 531

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 532

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 533

    In mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has insta...

  • Page 534

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 535

    Mopar® parts mopar® fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehi...

  • Page 536

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, master- card, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 537

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 538

    Traction grades the traction grades, from highest to lowest, are aa, a, b, and c. These grades represent the tire’s ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked c may have poor traction performan...

  • Page 539: Index

    Index 10

  • Page 540

    Abs (anti-lock brake system) . . . . . . . . . . . . . . . .356 adding engine coolant (antifreeze) . . . . . . . . . . . .487 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .407 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .482 additives, fuel . . . . . . . . . ...

  • Page 541

    Anti-lock brake system (abs) . . . . . . . . . . . . . . . .356 anti-lock warning light . . . . . . . . . . . . . . . . . . . .216 appearance care . . . . . . . . . . . . . . . . . . . . . . . . .499 assistance towing. . . . . . . . . . . . . . . . . . . . . . . . .125 automatic dimming mirror . . ....

  • Page 542

    Calibration, compass . . . . . . . . . . . . . . . . . . . . . .239 camera, rear . . . . . . . . . . . . . . . . . . . . . . . . . . . .176 capacities, antifreeze (engine coolant) . . . . . . . . . .514 capacities, fluid . . . . . . . . . . . . . . . . . . . . . . . . . .514 caps, filler fuel . . . ...

  • Page 543

    Older children and child restraints . . . . . . . . . .79 seating positions . . . . . . . . . . . . . . . . . . . . . . . .82 child safety locks . . . . . . . . . . . . . . . . . . . . . . . . .34 clean air gasoline . . . . . . . . . . . . . . . . . . . . . . . .403 cleaning wheels . . . . . . . . ....

  • Page 544

    Data recorder, event . . . . . . . . . . . . . . . . . . . . . . .75 dealer service. . . . . . . . . . . . . . . . . . . . . . . . . . . .471 defroster, rear window. . . . . . . . . . . . . . . . . . . . .205 defroster, windshield . . . . . . . . . . . . . . . . . . . . . .100 delay (intermittent) w...

  • Page 545

    Emission control system maintenance . . . . . . . . . .470 engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .467 air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .476 block heater . . . . . . . . . . . . . . . . . . . . . . . . . .319 break-in recommendations . ....

  • Page 546

    Automatic transmission . . . . . . . . . . . . . . . . . .495 cooling system . . . . . . . . . . . . . . . . . . . . . . . . .485 power steering . . . . . . . . . . . . . . . . . . . . . . . . .352 fluids, lubricants and genuine parts . . . . . . . . . . .515 fog lights . . . . . . . . . . . . . . ....

  • Page 547

    Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .214 odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .223 tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . .217 gear ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . .325 gear select l...

  • Page 548

    Instrument cluster . . . . . . . . . . . . . . . . . . . . . . . .214 instrument panel and controls . . . . . . . . . . . . . . . .212 instrument panel cover . . . . . . . . . . . . . . . . . . . . .504 instrument panel lens cleaning . . . . . . . . . . . . . . .505 integrated power module (fuses) ....

  • Page 549

    Back-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .513 brake assist warning . . . . . . . . . . . . . . . . . . . .368 brake warning . . . . . . . . . . . . . . . . . . . . . . . . .217 bulb replacement . . . . . . . . . . . . . . . . . . . . . . .512 cargo . . . . . . . . . . . . . ...

  • Page 550

    Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 power door . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 lubrication, body . . . . . . . . . . . . . . . . . . . . . . . . .481 luggage rack (roof rack) . . . . . . . . . . . . . . . . . . .206 lug nuts . . . . . . ...

  • Page 551

    Occupant restraints . . . . . . . . . . . . . . . . . . . . . . . .39 octane rating, gasoline (fuel) . . . . . . . . . . . . . . . .403 odometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .223 trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .221 oil change indica...

  • Page 552

    Outlet (auxiliary electrical outlet) . . . . . . . . . . .191 steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .351 sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .188 transfer unit . . . . . . . . . . . . . . . . . . . . . . . . . .499 windows . . . . . . . . . ...

  • Page 553

    Replacement bulbs . . . . . . . . . . . . . . . . . . . . . . . .511 replacement keys . . . . . . . . . . . . . . . . . . . . . . . . .16 replacement parts. . . . . . . . . . . . . . . . . . . . . . . . .471 replacement tires . . . . . . . . . . . . . . . . . . . . . . . . .390 reporting safety defe...

  • Page 554

    Front seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 operating instructions . . . . . . . . . . . . . . . . . . . .45 pregnant women . . . . . . . . . . . . . . . . . . . . . . . .54 pretensioners . . . . . . . ....

  • Page 555

    Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .316 automatic transmission . . . . . . . . . . . . . . . . . .317 cold weather . . . . . . . . . . . . . . . . . . . . . . . . . .318 engine fails to start . . . . . . . . . . . . . . . . . . . . .318 manual transmission . . . ....

  • Page 556

    Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .432 life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . .389 load capacity . . . . . . . . . . . . . . . . . . . . . . . . .375 pressure monitor system (tpms) . . . . . . . . . . . .393 pressure warning light . . . . ...

  • Page 557

    Transmission automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . .322 fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .494 manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .319 transmitter battery service (remote keyless entry) . . .25 transmitter, gar...

  • Page 558

    Vanity mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . .110 variance, compass . . . . . . . . . . . . . . . . . . . . . . . .239 vehicle certification label . . . . . . . . . . . . . . . . . . .410 vehicle identification number (vin) . . . . . . . . . . . . .7 vehicle loading . . . . . ....

  • Page 559

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed prop- erly by trained personnel. The following must be obs...

  • Page 560

    Grand cherokee chrysler group llc o w n e r ’ s m a n u a l 2015 gr and cher ok ee 15wk741-126-aa first edition printed in u.S.A. 2 0 1 5.