1. DL manuals
  2. Jeep
  3. Automobile
  4. Compass 2015
  5. Owner's Manual

Jeep Compass 2015 Owner's Manual

Other manuals for Compass 2015: Operating Information Manual, Owner's Manual

Summary of Compass 2015

  • Page 1

    Compass o w n e r ’ s m a n u a l 20 15 c ompas s 15mk49-126-ad fourth edition printed in u.S.A. 2 0 1 5 fca us llc.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understa...

  • Page 5

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 rollover warning . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .5 䡵 warnings and cautions . . . . . . . . . . . . . .7 䡵 vehicle identification number . . . . . . . .7 ...

  • Page 6

    Introduction congratulations on selecting your new fca us llc vehicle. Be assured that it represents precision workman- ship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engine...

  • Page 7

    Control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully. Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the unive...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against operating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may miss importan...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right front body vin location 8 introduct...

  • Page 11

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .12 ▫ locking doors with a key. . . . . . . . . . . . . . . .14 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .14 䡵 sentry k...

  • Page 12

    ▫ to lock the doors and liftgate . . . . . . . . . . . .22 ▫ sound horn with remote key lock . . . . . . . . .22 ▫ flash lights with remote key lock/unlock . . .23 ▫ using the panic alarm . . . . . . . . . . . . . . . . . .24 ▫ programming additional transmitters. . . . . . . .25 ▫ transmitter batte...

  • Page 13

    䡵 engine break-in recommendations . . . .99 䡵 safety tips . . . . . . . . . . . . . . . . . . . . . . . . .100 ▫ transporting passengers . . . . . . . . . . . . . . . . .100 ▫ exhaust gas . . . . . . . . . . . . . . . . . . . . . . . . .101 ▫ safety checks you should make inside the vehicle . . . . ...

  • Page 14

    A word about your keys the authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition key removal 1. Place the shift lever in...

  • Page 15

    Note: if you try to remove the key before you place the shift lever in park, the key may become trapped tem- porarily in the ignition switch cylinder. If this occurs, place the shift lever in park, rotate the key clockwise slightly, and then remove the key as described above. If a malfunction occurs...

  • Page 16

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the gear selector. • do not leave the key fob in or near th...

  • Page 17

    Sentry key® the sentry key® immobilizer system prevents unau- thorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys that have an embedded el...

  • Page 18

    Caution! The sentry key® immobilizer system is not compat- ible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the keys provided with your new vehicle have been programmed to the vehicle electronics....

  • Page 19

    Customer key programming if you have two valid sentry keys®, you can program new sentry keys® to the system by performing the following procedure: 1. Cut the additional sentry key® transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the igniti...

  • Page 20

    Note: if a programmed key is lost, see your authorized dealer to have all remaining keys erased from the sys- tem’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of s...

  • Page 21

    To arm the system 1. Remove the key from the ignition switch and get out of the vehicle. 2. Lock the door using either the power door lock switch or the remote keyless entry (rke) transmitter and close all doors. 3. The vehicle security light in the instrument cluster will flash rapidly for approxim...

  • Page 22

    Once the vehicle security alarm is armed (after 16 seconds), when you pull the door handle to exit, the alarm will sound. If this occurs, push the unlock button on the rke transmitter to disarm the vehicle security alarm. Vehicle security alarm manual override the vehicle security alarm will not arm...

  • Page 23

    To unlock the doors and liftgate push and release the unlock button on the rke transmitter once to unlock the driver’s door or twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn o...

  • Page 24

    Note: pushing the lock button on the rke transmitter while you are inside the vehicle will activate the vehicle security alarm. Opening a door with the vehicle security alarm activated will cause the alarm to sound. Push the unlock button to deactivate the vehicle security alarm. Illuminated approac...

  • Page 25

    • for vehicles not equipped with the evic, perform the following steps: 1. Push the lock button on a programmed rke transmitter for at least 4 seconds, but no longer than 10 seconds. Then, push the panic button while still holding the lock button. 2. Release both buttons at the same time. 3. Test th...

  • Page 26

    • for vehicles not equipped with the evic, perform the following steps: 1. Push and hold the unlock button on a pro- grammed rke transmitter for at least 4 seconds but no longer than 10 seconds. Then, push and hold the lock button while still holding the unlock button. 2. Release both buttons at the...

  • Page 27

    Note: when you turn off the panic alarm by pushing the panic button a second time, you may have to move closer to the vehicle due to the radio frequency noises of the system. Programming additional transmitters refer to “sentry key®” in “things to know before starting” for further information. If yo...

  • Page 28

    3. To reassemble the rke transmitter case, snap the two halves together. Note: if the rke transmitter is equipped with a screw, reinstall and tighten the screw until snug. General information this device complies with part 15 of the fcc rules and rss-210 of industry canada. Operation is subject to t...

  • Page 29

    Note: • the vehicle must be equipped with an automatic transmission to be equipped with remote start. • obstructions between the vehicle and the key fob may reduce this range. How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in pa...

  • Page 30

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted — door ajar • remote start aborted — hood ajar • remote start abor...

  • Page 31

    • the engine can be started two consecutive times (two 15-minute cycles) with the rke transmitter. However, the ignition switch must be cycled to the on/run position before you can repeat the start sequence for a third cycle. Remote start will also cancel if any of the following occur: • the engine ...

  • Page 32

    Door locks manual door locks use the manual door lock knob to lock the doors from inside the vehicle. If the lock knob is down when the door is closed, the door will lock. Make sure the keys are not inside the vehicle before closing the door. Manual door lock knob 30 things to know before starting y...

  • Page 33

    Warning! • for personal security and safety in the event of an collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous...

  • Page 34

    Auto lock doors — if equipped the auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). Auto lock doors programming the automatic door locks feature can be enabled or disabled as follows: • for veh...

  • Page 35

    2. Within 15 seconds, cycle the ignition switch be- tween lock and on/run and then back to lock four times, ending up in the lock position (do not start the engine). 3. Within 30 seconds, push the power door lock switch to lock the doors. 4. A single chime will indicate the completion of the program...

  • Page 36

    Equipped/personal settings (customer- programmable features)” in “understanding your in- strument panel” for further information. • for vehicles not equipped with the evic, perform the following procedure: 1. Close all doors and place the key in the ignition. 2. Within 15 seconds, cycle the ignition...

  • Page 37

    3. Repeat steps 1 and 2 for the opposite rear door. Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Child-protection door lock location child-protection door lock function 2 thin...

  • Page 38

    Note: for emergency exit with the system engaged, move the lock knob up (unlocked position), roll down the window, and open the door with the outside door handle. Power windows — if equipped power window switches the window controls on the driver’s door trim panel control all the door windows. There...

  • Page 39

    Warning! Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave the key fob in or near the vehicle, or in a location accessible to children. Occupants, particu- larly unattended children, can become entrapped by the windows while operating the pow...

  • Page 40

    Window lockout switch the window lockout switch on the driver’s door allows you to disable the window controls on the rear passenger doors. To disable the window controls on the rear pas- senger doors, push the window lockout switch. To enable the rear window controls, push the window lockout switch...

  • Page 41

    Liftgate note: the key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate. To unlock the liftgate, insert the key into the lock and turn it to the right (manual lock models only). The liftgate can also be unlocked using the remote keyless entry (rke) tra...

  • Page 42

    • although the liftgate has no inside release mechanism, the liftgate trim panel includes an opening with a snap-in cap that provides access to release the latch in the event of an electrical system malfunction. Warning! • driving with the liftgate open can allow poisonous exhaust gases into your ve...

  • Page 43

    Important safety precautions please pay close attention to the information in this section. It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible. Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: 1. C...

  • Page 44

    8. Do not lean against the door or window. If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between occupants and the door and occupants could be injured. 9. If the air bag system in this vehicle needs to be modified to accommodate a ...

  • Page 45

    Enhanced seat belt use reminder system (beltalert) driver and passenger beltalert (if equipped) beltalert is a feature intended to remind the driver and outboard front seat passenger (if equipped with outboard front passenger beltalert) to buckle their seat belts. The belt alert feature is active wh...

  • Page 46

    Change of status if the driver or outboard front seat passenger (if equipped with outboard front passenger seat beltalert) unbuckles their seat belt while the vehicle is traveling, the beltalert warning sequence will begin until the seat belts are buckled again. The outboard front passenger seat bel...

  • Page 47

    Warning! • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belt even though you have air bags. • in a collision, you and your p...

  • Page 48

    Warning! (continued) • a lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug. • a twisted seat belt may not pro...

  • Page 49

    Warning! (continued) • a shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. • a frayed or torn seat belt could rip apa...

  • Page 50

    3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt i...

  • Page 51

    6. To release the seat belt, push the red button on the buckle. The seat belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the seat belt to retract fully. Second row center seat belt operating instructions the second row center seat...

  • Page 52

    Routing the rear center shoulder belt connecting mini-latch to buckle 50 things to know before starting your vehicle.

  • Page 53

    2. Grasp the mini-latch plate and pull the seat belt over the seat. 3. Route the shoulder belt to the inside of the right head restraint. Rear center seat belt buckled detaching mini-latch and buckle 2 things to know before starting your vehicle 51.

  • Page 54

    4. When the seat belt is long enough to fit, insert the mini-latch plate into the mini-buckle until you hear a “click.” 5. Sit back in seat. Slide the regular latch plate up the webbing as far as necessary to allow the seat belt to go around your lap. 6. When the seat belt is long enough to fit, ins...

  • Page 55

    Warning! (continued) • when reattaching the mini-latch plate and mini- buckle, ensure the seat belt webbing is not twisted. If the webbing is twisted, follow the preceding procedure to detach the mini-latch plate and mini- buckle, untwist the webbing, and reattach the mini-latch plate and mini-buckl...

  • Page 56

    As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position. After you release the anchorage button, try to move it up or down to make sure that it i...

  • Page 57

    Warning! • only use a seat belt extender if it is physically required in order to properly fit the original seat belt system. Do not use the seat belt extender if, when worn, the distance between the front edge of the seat belt extender buckle and the center of the occupant’s body is less than 6 inc...

  • Page 58

    The pretensioners are triggered by the occupant re- straint controller (orc). Like the air bags, the preten- sioners are single use items. A deployed pretensioner or a deployed air bag must be replaced immediately. Energy management feature this vehicle has a seat belt system with an energy manageme...

  • Page 59

    If the passenger seating position is equipped with an alr and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the alr. If the alr is activated, you will hear a clicking sound as the seat belt r...

  • Page 60

    How to disengage the automatic locking mode unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Warning! • the seat belt assembly must be replaced if the switchable automati...

  • Page 61

    How the active head restraints (ahr) work the occupant restraint controller (orc) determines whether the severity, or type of rear impact will require the active head restraints (ahr) to deploy. If a rear impact requires deployment, both the driver and front passenger seat ahrs will be deployed. Whe...

  • Page 62

    Warning! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. Note: refer to “adjusting active head restraints” in “under...

  • Page 63

    A — downward movement b — rearward movement c — final downward movement to engage locking mechanism 4. The ahr front soft foam and trim half should lock into the back decorative plastic half. Review table below 2 things to know before starting your vehicle 61.

  • Page 64

    Note: • if you have difficulties or problems resetting the active head restraints, see an authorized dealer. • for safety reasons, have the active head restraints checked by a qualified specialist at an authorized dealer. Supplemental restraint system (srs) air bag system components your vehicle may...

  • Page 65

    • seat belt buckle switch • seat track position sensors advanced front air bags this vehicle has advanced front air bags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s advanced front air bag is mounted in the center of the steering wheel. The...

  • Page 66

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 67

    Warning! • no objects should be placed over or near the air bag on the instrument panel or steering wheel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bags to inflate. • do not put anything on or around the air bag covers or attempt to op...

  • Page 68

    On the other hand, depending on the type and location of impact, advanced front air bags may deploy in crashes with little vehicle front-end damage but that produce a severe initial deceleration. Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves a...

  • Page 69

    Warning! • do not drill, cut, or tamper with the knee impact bolsters in any way. • do not mount any accessories to the knee impact bolsters such as alarm lights, stereos, citizen band radios, etc. Supplemental side air bags your vehicle is equipped with two types of side air bags: 1. Supplemental s...

  • Page 70

    When the sab deploys, it opens the seam on the out- board side of the seatback’s trim cover. The inflating sab deploys through the seat seam into the space between the occupant and the door. The sab moves at a very high speed and with such a high force that it could injure you if you are not seated ...

  • Page 71

    Sabics may help reduce the risk of head injury to front and rear seat outboard occupants. Sabics may reduce the risk of injuries in certain side impact and vehicle rollover events, in addition to the injury reduction poten- tial provided by the seat belts and body structure. The sabics deploy downwa...

  • Page 72

    The sabics and sabs (“side air bags”) are designed to activate in certain side impacts and certain rollover events. The occupant restraint controller (“orc”) de- termines whether the deployment of the side air bags in a particular side impact or rollover event is appropriate, based on the severity a...

  • Page 73

    Warning! (continued) • relying on the side air bags alone could lead to more severe injuries in a collision. The side air bags work with your seat belt to restrain you properly. In some collisions, side air bags won’t deploy at all. Always wear your seat belt even though you have side air bags. Note...

  • Page 74

    Faster-developing event may deploy the seat belt preten- sioners as well as the sabs and sabics on both sides of the vehicle. The rollover sensing-system may also deploy the seat belt pretensioners, with or without the sabs and sabics, on both sides of the vehicle if the vehicle experiences a near r...

  • Page 75

    Do not drive your vehicle after the air bags have de- ployed. If you are involved in another collision, the air bags will not be in place to protect you. Warning! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and th...

  • Page 76

    System reset procedure in order to reset the enhanced accident response system functions after an event, the ignition must be changed from ignition start or on/run to ignition off. Air bag warning light the air bags must be ready to inflate for your protection in a collision. The occupant re- strain...

  • Page 77

    Free, if any of the following occurs, have an authorized dealer service the air bag system immediately. • the air bag warning light does not come on during the four to eight seconds when the ignition switch is first turned to the on/run position. • the air bag warning light remains on after the four...

  • Page 78

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 79

    Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The main purpose of an edr is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per-...

  • Page 80

    Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the united states, and every canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be pros- ecuted for ignoring it. Ch...

  • Page 81

    Note: • for additional information, refer to www.Seatcheck.Org or call 1–866–732–8243. Canadian residents should refer to transport canada’s website for additional information: • http://www.Tc.Gc.Ca/eng/roadsafety/ safedrivers-childsafety-index-53.Htm summary of recommendations for restraining child...

  • Page 82

    Child size, height, weight or age recommended type of child restraint larger children children who have out-grown their forward-facing child restraint, but are too small to properly fit the vehicle’s seat belt belt positioning booster seat and the vehicle seat belt, seated in the rear seat of the ve...

  • Page 83

    Highest weight or height allowed by their convertible child seat. Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child rest...

  • Page 84

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • after a child restraint i...

  • Page 85

    2. Do the child’s knees bend comfortably over the front of the vehicle seat – while they are still sitting all the way back? 3. Does the shoulder belt cross the child’s shoulder between their neck and arm? 4. Is the lap part of the belt as low as possible, touching the child’s thighs and not their s...

  • Page 86

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 87

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 88

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 86 things to know before starting your vehicle.

  • Page 89

    Latch position table what is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use t...

  • Page 90

    Latch position table can two child restraints be attached us- ing a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to install a child seat in the center posit...

  • Page 91

    Locating latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the ...

  • Page 92

    Locating tether anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower ancho...

  • Page 93

    Warning! Never use the same lower anchorage to attach more than one child restraint. If you are installing latch- compatible child restraints next to each other, you must use the seat belt for the center position. You can then use either the latch anchors or the vehicle’s seat belt for installing ch...

  • Page 94

    3. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 4. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tio...

  • Page 95

    Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • child restraint anchorages ar...

  • Page 96

    Lap/shoulder belt systems for installing child restraints in this vehicle • alr = switchable automatic locking retractor • top tether anchorage symbol 94 things to know before starting your vehicle.

  • Page 97

    Lap/shoulder belt systems what is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a for- ward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a fo...

  • Page 98

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 99

    9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. Installing c...

  • Page 100

    1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another p...

  • Page 101

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 102

    Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem. Safety tip...

  • Page 103

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 104

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 105

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 106

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks, and bulges. C...

  • Page 107

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 ▫ inside day/night mirror . . . . . . . . . . . . . . . .110 ▫ automatic dimming mirror — if equipped . . .111 ▫ outside mirror — driver side . . . . . . . . . . . .112 ▫ outside ...

  • Page 108

    䡵 voice command — if equipped . . . . . . . .145 ▫ voice command system operation . . . . . . . . .145 ▫ commands . . . . . . . . . . . . . . . . . . . . . . . . .147 ▫ voice training . . . . . . . . . . . . . . . . . . . . . . .151 䡵 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 109

    ▫ map/reading lights . . . . . . . . . . . . . . . . . . .169 䡵 windshield wipers and washers . . . . . .170 ▫ windshield wiper operation . . . . . . . . . . . . .171 ▫ intermittent wiper system . . . . . . . . . . . . . . .172 ▫ windshield washers . . . . . . . . . . . . . . . . . . .172 ▫ mist fea...

  • Page 110

    䡵 power sunroof — if equipped . . . . . . . .190 ▫ opening sunroof — express . . . . . . . . . . . . . .191 ▫ opening sunroof — manual mode . . . . . . . . .191 ▫ closing sunroof — express. . . . . . . . . . . . . . .191 ▫ closing sunroof — manual mode . . . . . . . . . .191 ▫ pinch protect feature ...

  • Page 111

    䡵 rear window features . . . . . . . . . . . . . .206 ▫ rear window wiper/washer . . . . . . . . . . . . .206 ▫ rear window defroster . . . . . . . . . . . . . . . . .207 䡵 roof luggage rack — if equipped . . . .208 3 understanding the features of your vehicle 109.

  • Page 112

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicl...

  • Page 113

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pushing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activat...

  • Page 114

    Outside mirror — driver side adjust the flat outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle with your head close to the door glass. Outside mirror — passenger side adjust the convex outside mirror so you can just see the side of your vehi...

  • Page 115

    Power mirrors the power mirror control is located on the driver’s door trim panel. To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When you are finished adjusting the mirror, turn the c...

  • Page 116

    Vanity mirrors — if equipped to use the vanity mirror, rotate the sun visor down and swing the mirror cover upward. Sun visor “slide-on-rod” feature — if equipped the sun visors may be extended out to provide more coverage of the side glass. Uconnect® phone — if equipped uconnect® phone is a voice-a...

  • Page 117

    For uconnect® customer support: • u.S. Residents - visit uconnectphone.Com or call 1-877- 855-8400. • canadian residents - visit uconnectphone.Com or call, 1-800-465-2001 (english) or 1-800-387-9983 (french). Uconnect® phone allows you to transfer calls between the system and your mobile phone as yo...

  • Page 118

    Access the system. When you push the button you will hear the word uconnect® followed by a beep. The beep is your signal to give a command. Voice command button actual button location may vary with the ra- dio. The individual buttons are described in the “operation” section. The uconnect® phone can ...

  • Page 119

    • for each feature explanation in this section, only the compound form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it. For example, you can use the compound form voice com- mand “phonebook new entry,” or you can br...

  • Page 120

    The following are general phone to uconnect® phone pairing instructions: 1. Activate the bluetooth® on your mobile phone. 2. Push the phone button to begin. 3. After the “ready” prompt and the following beep, say “device pairing.” 4. When prompted, after the beep, say “pair a device” and follow the ...

  • Page 121

    Dial by saying a number • push the phone button to begin. • after the “ready” prompt and the following beep, say “dial.” • the system will prompt you to say the number you want to call. • for example, you can say “234-567-8901.” • the uconnect® phone will confirm the phone number and then dial. The ...

  • Page 122

    To add names to the uconnect® phonebook using voice commands: 1. Push the phone button to begin. 2. After the “ready” prompt and the following beep, say “phonebook new entry.” 3. When prompted, say the name of the new entry. Use of long names helps the voice command and it is recommended. For exampl...

  • Page 123

    Book access profile may support this feature. See uconnect® website for supported phones. • to call a name from the uconnect® phonebook or downloaded phonebook, follow the procedure in “call by saying a name” section. • automatic download and update, if supported, begins as soon as the bluetooth® wi...

  • Page 124

    • you will then be asked for the name of the phonebook entry that you wish to edit. • next, choose the number designation (home, work, mobile, or other) that you wish to edit. • when prompted, recite the new phone number for the phonebook entry that you are editing. After you are finished editing an...

  • Page 125

    4. After you enter the name, the uconnect® phone will ask you which designation you wish to delete: home, work, mobile, other, or all. Say the designation you wish to delete. • note that only the phonebook entry in the current language is deleted. Note: automatic downloaded phonebook entries can- no...

  • Page 126

    3. To call one of the names in the list, push the voice command button during the playing of the desired name, and say “call.” note: the user can also exercise “edit” or “delete” operations at this point. 4. The uconnect® phone will then prompt you as to the number designation you wish to call. • th...

  • Page 127

    • push the phone button to place the current call on hold and answer the incoming call. Note: the uconnect® phone compatible phones in the market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can only answer an incoming call or ignore it. Makin...

  • Page 128

    Conference call when two calls are in progress (one active and one on hold): 1. Push and hold the phone button until you hear a double beep, indicating that the two calls have been joined into one conference call. Three-way calling to initiate three-way calling, push the voice command button while a...

  • Page 129

    • the uconnect® phone will call the last number that was dialed from your mobile phone. Note: this may not be the last number dialed from the uconnect® phone. Call continuation call continuation is the progression of a phone call on the uconnect® phone after the vehicle ignition has been switched to...

  • Page 130

    After selecting one of the languages, all prompts and voice commands will be in that language. Note: after every uconnect® phone language change operation, only the language-specific 32 name phone- book is usable. The paired phone name is not language- specific and is usable across all languages. Em...

  • Page 131

    Warning! To use your uconnect® phone system in an emer- gency, your mobile phone must be: • turned on. • paired to the uconnect® system. • have network coverage. Roadside assistance/towing assistance if you need roadside assistance: • push the phone button to begin. • after the “ready” prompt and th...

  • Page 132

    Working with automated systems this method is used in instances where one generally has to push numbers on the mobile phone keypad while navigating through an automated telephone system. You can use your uconnect® phone to access a voice mail system or an automated service, such as a paging service ...

  • Page 133

    • some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature. Barge in — overriding prompts the “voice command” button can be used when you wish to skip part of a prompt and issue your voice command immediately. For example, if a pro...

  • Page 134

    Dialing a number with your paired bluetooth® mobile phone, the audio will be played through your vehicle’s audio system. The uconnect® phone will work the same as if you dial the number using voice command. Note: certain brands of mobile phones do not send the dial ring to the uconnect® phone to pla...

  • Page 135

    Connect or disconnect link between the uconnect® phone and mobile phone your mobile phone can be paired with many different electronic devices, but can only be actively “connected” with one electronic device at a time. If you would like to connect or disconnect the bluetooth® connection between your...

  • Page 136

    • the selected phone will be used for the next phone call. If the selected phone is not available, the uconnect® phone will return to using the highest priority phone present in or near (approximately within 30 ft. [9 m]) the vehicle. Delete uconnect® phone paired mobile phones to delete mobile phon...

  • Page 137

    You can either push the uconnect® phone button to restore the factory setting or repeat the words and phrases when prompted by the uconnect® phone. For best results, the voice training session should be com- pleted when the vehicle is parked with the engine running, all windows closed, and the blowe...

  • Page 138

    Performance is maximized under: • low-to-medium blower setting • low-to-medium vehicle speed • low road noise • smooth road surface • fully closed windows • dry weather condition note: • even though the system is designed for users speaking in north american english, french, and spanish ac- cents, t...

  • Page 139

    Far end audio performance audio quality is maximized under: • low-to-medium blower setting • low-to-medium vehicle speed • low road noise • smooth road surface • fully closed windows • dry weather conditions • operation from the driver’s seat • performance, such as audio clarity, echo, and loudness ...

  • Page 140

    3. Uconnect® phone will play the new text message for you. After reading a message, you can “reply” or “forward” the message using uconnect® phone. Send messages: you can send messages using uconnect® phone. To send a new message: 1. Push the phone button. 2. After the “ready” prompt and the followi...

  • Page 141

    13. I’ll be late. 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye for now. 18. When can we meet? 19. Send number to call. 20. Start without me. Turn voice text reply incoming announcement on/ off turning the voice text reply incoming announcement off will stop the system ...

  • Page 142

    140 understanding the features of your vehicle.

  • Page 143

    3 understanding the features of your vehicle 141.

  • Page 144

    142 understanding the features of your vehicle.

  • Page 145

    Voice commands primary alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location primary alternate (s) all call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help 3 understanding the features...

  • Page 146

    Primary alternate (s) home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book previous record again primary alternate (s) redial return to main menu return or main menu select phone select send set up phone settings or phon...

  • Page 147

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 148

    Warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your at- tention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. When y...

  • Page 149

    To hear the first available menu, push the voice com- mand button and say “help” or “main menu.” commands the voice command system understands two types of commands, universal commands and local commands. Universal commands are available at all times. Local commands are available if the supported ra...

  • Page 150

    Radio am to switch to the am band, say “am” or “radio am.” in this mode, you may say the following commands: • “frequency #” (to change the frequency) • “next station” (to select the next station) • “previous station” (to select the previous station) • “radio menu” (to switch to the radio menu) • “m...

  • Page 151

    Disc mode to switch to the disc mode, say “disc.” in this mode, you may say the following commands: • “track” (#) (to change the track) • “next track” (to play the next track) • “previous track” (to play the previous track) • “main menu” (to switch to the main menu) usb mode to switch to usb mode, s...

  • Page 152

    – “continue” (to continue recording) – “delete” (to delete the recording) • “play memos” (to play previously recorded memos) — during the playback you may push the voice com- mand button to stop playing memos. You pro- ceed by saying one of the following commands: – “repeat” (to repeat a memo) – “ne...

  • Page 153

    Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect® voice “voice training” feature may be used. 1. Push the voice command button, say “system setup” and once you are in that menu then say “voice training.” this will train your ...

  • Page 154

    Power seats — if equipped some models may be equipped with a power driver’s seat. The power seat switch is located on the outboard side of the seat near the floor. Use the switch to move the seat up, down, forward, rearward, or to tilt the seat. Warning! • adjusting a seat while driving may be dange...

  • Page 155

    Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward. The seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting the seat up or down the height of the seats...

  • Page 156

    Minutes of continuous operation. At that time, the dis- play will change from hi to lo, indicating the change. When the lo-level heating is selected, the system auto- matically turns the heater and the indicator light off after approximately 30 minutes of continuous operation. Note: once a heat sett...

  • Page 157

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 158

    Manual seat height adjustment — if equipped the driver’s seat height can be raised or lowered by using a lever, located on the outboard side of the seat. Pull upward on the lever to raise the seat height or push downward on the lever to lower the seat height. Manual lumbar — if equipped the lumbar a...

  • Page 159

    Driver’s seatback recline to adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired angle and release the lever. To return the seatback, lift the lever, lean forward and release the lever. Warning! Do not ride with the seatback reclined so that the sho...

  • Page 160

    Warning! The head restraints for all occupants must be prop- erly installed and adjusted prior to operating the vehicle or occupying a seat. Head restraints should never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause ...

  • Page 161

    To raise the head restraint, pull upward on the head restraint. To lower the head restraint, push the adjust- ment button located at the base of the head restraint and push downward on the head restraint. For comfort the active head restraints can be tilted forward and backward. To tilt the head res...

  • Page 162

    Note: • the head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head re...

  • Page 163

    Warning! (continued) • active head restraints may be deployed if they are struck by an object such as a hand, foot or loose cargo. To avoid accidental deployment of the ac- tive head restraint ensure that all cargo is secured, as loose cargo could contact the active head re- straint during sudden st...

  • Page 164

    To raise the seatback, pull the strap forward and lift the seatback into its upright position. Warning! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers...

  • Page 165

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. To open and close the hood to open the hoo...

  • Page 166

    2. Move the safety latch, located outside the vehicle under the front edge of the hood, toward the center and raise the hood. Lift the hood prop rod, clipped to the right side (left side facing hood) of the engine compartment to secure the hood in the open position. Place the hood prop at the locati...

  • Page 167

    Caution! To prevent possible damage: • before closing hood, make sure the hood prop rod is fully seated into its storage retaining clips. • do not slam the hood to close it. Use a firm downward push at the center front edge of the hood to ensure that both latches engage. Never drive your vehicle unl...

  • Page 168

    Headlights and parking lights turn the end of the multifunction lever to the first detent to turn on the parking lights. Turn the end of the lever to the second detent to turn on the headlights. Daytime running lights — if equipped the high beam lights will come on as daytime running lights (lower i...

  • Page 169

    Note: the fog lights will only operate with the head- lights on low beam. Selecting high beam headlights will turn off the fog lights. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn ...

  • Page 170

    Note: if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. Lane change assist tap the lever up or down once, without ...

  • Page 171

    Rotate the center portion of the lever upward to the next detent position to brighten the odometer and radio when the parking lights or headlights are on. Rotate the center portion of the lever upward to the last detent to turn on the interior lighting. Map/reading lights these lights are mounted be...

  • Page 172

    Note: the lights will remain on until the switch is pushed a second time, so be sure they have been turned off before leaving the vehicle. They will not turn off automatically. Windshield wipers and washers the windshield wiper/washer control lever is located on the right side of the steering column...

  • Page 173

    Caution! • turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • in cold weather, always turn off the wiper switch and allow the wipers to return to the “park” posi- tion be...

  • Page 174

    Intermittent wiper system use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Select the delay interval by turning the end of the lever. Rotate the end of the lever upward (clockwise) to decrease the delay time and downwar...

  • Page 175

    Mist feature push down on the control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. Note: the mist feature does not activate the washer pump; therefore, no washer fluid wil...

  • Page 176

    Push down on the lever to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Push the lever up to lock the steering column firmly in place. Warning! Do not adjust the steering column while driving. Adjusting the steering column wh...

  • Page 177

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 178

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To set a desired speed turn the elec...

  • Page 179

    The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “under- standing your instrument panel” for more information. The speed increment shown is dependant on the chosen speed unit of u.S. (mph) or metric (km/h): u.S. Speed (mph) • pushing the res (+)...

  • Page 180

    • if the button is continually pushed, the set speed will continue to decrease until the button is released, then the new set speed will be established. Metric speed (km/h) • pushing the set (-) button once will result in a 1 km/h decrease in set speed. Each subsequent tap of the button results in a...

  • Page 181

    Parkview® rear back up camera — if equipped your vehicle may be equipped with the parkview® rear back up camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into reverse. The image will be displayed on the touchscreen along with a...

  • Page 182

    When displayed, static grid lines will illustrate the width of the vehicle while a dashed center-line will indicate the center of the vehicle to assist with aligning to a hitch/ receiver. The static grid lines will show separate zones that will help indicate the distance to the rear of the vehicle. ...

  • Page 183

    Caution! (continued) • to avoid vehicle damage, the vehicle must be driven slowly when using parkview® to be able to stop in time when an obstacle is seen. It is recom- mended that the driver look frequently over his/her shoulder when using parkview®. Note: if snow, ice, mud, or any foreign substanc...

  • Page 184

    Note: homelink® is disabled when the vehicle secu- rity alarm is active. Before you begin programming homelink® be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recom...

  • Page 185

    Programming a rolling code for programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “learn” or “train” button located where the hanging antenna is attached to the garage door opener. It is not the button that is normally used to open...

  • Page 186

    2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink® button you wish to program while keeping the homelink® indicator light in view. 3. Push and hold the homelink® button you want to program while you push and hold the hand-held transmitter button. 4. Continue to hold...

  • Page 187

    Reprogramming a single homelink® button (rolling code) to reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the on/run position. 2. Push and hold the desired homelink® button until the indicator light begins to flash after 20 seconds. Do not release t...

  • Page 188

    • to program the two remaining homelink® buttons, repeat each step for each remaining button. Do not erase the channels. Reprogramming a single homelink® button (non-rolling code) to reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the on/run positio...

  • Page 189

    2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink® button you wish to program while keeping the homelink® indicator light in view. 3. Continue to push and hold the homelink® button, while you push and release (“cycle”) your hand-held transmitter every two seconds un...

  • Page 190

    3. Without releasing the button proceed with “canadian/gate operator programming” step 2 and follow all remaining steps. Using homelink® to operate, push and release the programmed homelink® button. Activation will now occur for the programmed device (i.E., garage door opener, gate opera- tor, secur...

  • Page 191

    Warning! • vehicle exhaust contains carbon monoxide, a dan- gerous gas. Do not run your vehicle in the garage while programming the transceiver. Exhaust gas can cause serious injury or death. • your motorized door or gate will open and close while you are programming the universal trans- ceiver. Do ...

  • Page 192

    Power sunroof — if equipped the power sunroof switch is located on the overhead console. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location acces- sible to children. Occupants, particularly unat-...

  • Page 193

    Opening sunroof — express push the switch rearward and release it within one-half second. The sunroof and sunshade will open automati- cally from any position. The sunroof and sunshade will open fully and stop automatically. This is called “express open”. During express open operation, any movement ...

  • Page 194

    Venting sunroof — express push and release the vent button within one half second and the sunroof will open to the vent position. This is called “express vent”, and it will occur regardless of sunroof position. During express vent operation, any movement of the switch will stop the sunroof. Sunshade...

  • Page 195

    For vehicles equipped with the evic the power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is turned to the lock position. Opening either front door will cancel this feature. Electrical power outlets there is a standard 12 volt (13 amp) power outlet...

  • Page 196

    Note: to ensure proper operation a mopar® knob and element must be used. Caution! • do not exceed the maximum power of 160 watts (13 amps) at 12 volts. If the 160 watt (13 amp) power rating is exceeded the fuse protecting the system will need to be replaced. • power outlets are designed for accessor...

  • Page 197

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 198

    Power inverter — if equipped a 115 volt (150 watt) ac power inverter is located on the front of the center console for added convenience. This outlet can power mobile phones, electronics and other low power devices requiring power up to 150 watts. Certain high-end video games, such as playstation®3 ...

  • Page 199

    Warning! To avoid serious injury or death: • do not use a three-prong adaptor. • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when not in use. • if this outlet is mishandled, it may cause an electric shock and failure. Caution! • many accessories tha...

  • Page 200

    Cupholders your vehicle is equipped with four cupholders. There are two illuminated cupholders located in the front. There are two cupholders located in the back for the rear passengers. Front cupholders rear cupholders 198 understanding the features of your vehicle.

  • Page 201

    Storage glove compartment and storage bin located on the passenger side of the instrument panel are an upper storage bin and a lower glove compartment. To open the lower glove compartment, pull outward on the release handle. Storage bins 1 — upper storage bin 2 — lower glove compartment glove compar...

  • Page 202

    Door storage the interior door panels are equipped with lower storage areas. Front door storage rear door storage 200 understanding the features of your vehicle.

  • Page 203

    Console features the floor console contains both an upper and lower storage compartment. To open the upper storage compartment, push inward on the upper handle to unlatch the upper lid and lift the lid open. To open the lower storage compartment, lift upward on the lower handle to unlatch the lower ...

  • Page 204

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. Cargo area features cargo light the light is mounted in the headliner above the cargo area to illuminate the cargo area. Carg...

  • Page 205

    Using the handle, pull the cover toward you and guide the rear cover posts into the guides located on both sides of the rear trim panel. Warning! In a collision a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store...

  • Page 206

    Removable load floor the cargo area load floor is removable and can be washed with mild soap and water. Cargo tie-down loops there are four tie-downs (d-rings) installed in the cargo area for securing cargo. Removable load floor cargo area tie-downs 204 understanding the features of your vehicle.

  • Page 207

    Warning! • cargo tie-down loops are not safe anchors for a child seat tether strap. In a sudden stop or collision a loop could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • the weight and position of cargo a...

  • Page 208

    Fold down speakers — if equipped when the liftgate is open, the speakers can swing down off the trim panel to face rearward, for tailgating and other activities. Rear window features rear window wiper/washer the rear wiper/washer is controlled by a rotary switch located on the center portion of the ...

  • Page 209

    Rotate the center portion of the lever upward to the first detent position for rear wiper operation. Note: the rear wiper operates in an intermittent mode only. Rotate the center portion of the lever past the first detent to activate the rear washer. The washer pump and the wiper will continue to op...

  • Page 210

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 211

    The crossbars must also be secured in one of the seven detent positions marked with an arrow on the siderails to prevent movement. To move the crossbars, loosen the thumb screws located at the upper edge of each crossbar approximately eight turns, then move the crossbar to the desired position, keep...

  • Page 212

    Caution! (continued) • to avoid damage to the luggage rack and vehicle, do not exceed the maximum luggage rack load capacity of 150 lb (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately. • long loads which extend over the windshield, such as wood panels or...

  • Page 213

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .214 䡵 instrument cluster . . . . . . . . . . . . . . . . .215 䡵 instrument cluster descriptions . . . . .216 䡵 mini-trip computer — if equipped . . . . .230 ▫ control buttons . . . . . . . . . . . . . . . . ....

  • Page 214

    ▫ operating instructions — radio mode. . . . . . .243 ▫ operation instructions — disc mode for cd and mp3/wma audio play, dvd – video . . . . . . .251 ▫ list button — disc mode for mp3/wma play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .256 ▫ info button — disc mode for mp3/wma pla...

  • Page 215

    䡵 ipod®/usb/mp3 control — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .288 ▫ connecting the ipod® or external usb device . . . . . . . . . . . . . . . . . . . . . . . . . . . . .289 ▫ using this feature. . . . . . . . . . . . . . . . . . . . .289 ▫ controlling the ipod® or external u...

  • Page 216

    Instrument panel features 1 — air outlet 5 — storage bin 9 — heated seat switch – if equipped 2 — demisters 6 — glove compartment 10 — hazard warning flasher 3 — instrument cluster 7 — climate controls 11 — esc off switch – if equipped 4 — radio 8 — power outlet 12 — heated seat switch – if equipped...

  • Page 217

    Instrument cluster 4 understanding your instrument panel 215.

  • Page 218

    Instrument cluster descriptions 1. Fuel gauge /fuel door reminder when the ignition switch is in the on/run position, the pointer will show the level of fuel remaining in the fuel tank. The fuel pump symbol points to the side of the vehicle where the fuel door is located. 2. Charging system light th...

  • Page 219

    On briefly as a bulb check. If the light does not come on during starting, have the system checked by an autho- rized dealer. 4. Oil pressure warning light this light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while drivi...

  • Page 220

    Will sound to alert you to turn the signals off. If either indicator flashes at a rapid rate, check for a defective outside light bulb. 9. High beam indicator this indicator shows that the high beam head- lights are on. Push the multifunction lever for- ward to switch the headlights to high beam, an...

  • Page 221

    12. Tachometer the white area of the scale shows the permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 13. Engine temperature warning light this light warns of an overheated engine condi- tio...

  • Page 222

    Booster, the abs pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by ...

  • Page 223

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 15. Transmission temperature warning light this light indicates that the t...

  • Page 224

    The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. Caution! Driving with a hot engine cooling system could damage your vehicle. If ...

  • Page 225

    20. Shift lever indicator the shift lever indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. Note: you must apply the brakes before shifting from park. 21. Odometer/trip odometer reset button push this button to change the display ...

  • Page 226

    Maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the tpms low tire pressure telltale. Your vehicle has also been equipped with a tpms malfunction indicator to indicate when the system is not operating properly. The tpms malfunction indicato...

  • Page 227

    23. Odometer display/trip odometer display area this display indicates the total distance the vehicle has been driven. Note: u.S. Federal regulations require that upon trans- fer of vehicle ownership, the seller certify to the pur- chaser the correct mileage that the vehicle has been driven. If your...

  • Page 228

    Note: if the vehicle is equipped with the optional electronic vehicle information center (evic) in the in- strument cluster, all warnings including “door ajar”, and “gate ajar” will only be displayed in the evic display. Refer to “electronic vehicle information center — if equipped” for additional i...

  • Page 229

    Engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the on/run position. To turn off the message temporarily, push and release the trip odometer button on the instrument clu...

  • Page 230

    Caution! Prolonged driving with the malfunction indicator light (mil) on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the mil is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. Warni...

  • Page 231

    Running, a malfunction has been detected in the esc system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and cor...

  • Page 232

    30. Hill descent indicator — if equipped the symbol illuminates (is armed) when the 4wd lock switch is activated and the trans- mission range indicator is in low or reverse position (off-road mode). Mini-trip computer — if equipped the mini-trip computer is located in the instrument cluster and feat...

  • Page 233

    Reset button to reset the display shown, turn the ignition switch to the on position, then push and hold the reset button located on the steering wheel. The following displays can be reset or changed: • trip a • trip b trip odometer (odo) this display shows the distance traveled since the last reset...

  • Page 234

    The evic consists of the following: • system status • units • vehicle information warning message displays • personal settings (customer-programmable features) • compass heading • outside temperature display • trip computer functions • uconnect® phone displays (if equipped) • audio mode display • ti...

  • Page 235

    Menu button push and release the menu button to scroll through the main menus (fuel economy, warn- ings, timer, units, system, personal settings) or to exit submenus. Compass button push and release the compass button to display one of eight compass readings and the outside temperature or to exit su...

  • Page 236

    • personal settings not avail. — vehicle is not in park (automatic transmission), or vehicle is in motion (manual transmission). • door ajar (with vehicle graphic showing which door is open. A single chime sounds if the vehicle is in motion). • doors ajar (with vehicle graphic showing which doors ar...

  • Page 237

    Unless reset, this message will continue to display each time you turn the ignition switch to the on/run position. To turn off the message temporarily, push and release the trip odometer button on the instrument cluster. To reset the oil change indicator system (after performing the scheduled mainte...

  • Page 238

    Time within three seconds of resetting the currently displayed function. Reset all will be displayed during this three-second window. Compass/temperature/audio push and release the compass button to display one of eight compass headings to indicate the direction the vehicle is facing, the outside te...

  • Page 239

    Tire pressure monitor (tpm) refer to “tire pressure monitoring system (tpms)” in “starting and operating” for system operation. Elapsed time shows the total elapsed time of travel since the last reset. Elapsed time will increment when the ignition switch is in the run/start position. Elapsed time is...

  • Page 240

    Pushing the right/select button while in this display selects english, espanol, deutsch, italiano, francais, or nl depending on availability. As you continue, the displayed information will be shown in the selected language. Note: uconnect® language will not change using the evic. Please refer to “u...

  • Page 241

    Rke transmitter. This feature may be selected with or without the sound horn with lock feature selected. Push and hold the select button when in this display until “on” or “off” appears to make your selection. Sound horn with lock when on is selected, a short horn sound will occur when the rke trans...

  • Page 242

    Hill start assist (hsa) — if equipped when on is selected, the hsa system is active. Refer to “electronic brake control system” in “starting and operating” for system function and operating informa- tion. To make your selection, push and release the right arrow button until “on” or “off” appears. Di...

  • Page 243

    3. Push and release the down button until “calibrate compass” displays in the evic. 4. Push and release the right arrow button to start the calibration. The “cal” indicator will display in the evic. 5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until...

  • Page 244

    2. Push and hold the compass button for approxi- mately two seconds. 3. Push and release the down button until “compass variance” message and the last variance zone number displays in the evic. 4. Push and release the select button until the proper variance zone is selected according to the map. 5. ...

  • Page 245

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 246

    Voice command button uconnect® phone — if equipped push this button to operate the uconnect® phone feature (if equipped). Refer to “voice command” for further details. If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with uconnect phone” message ...

  • Page 247

    The clock can also be set by pushing the setup button and selecting the “set home clock” entry. Once in this display follow the above procedure, starting at step 2. Info button push the info button for an rds station (one with call letters displayed). The radio will return a radio text message broad...

  • Page 248

    Push the rotary tune/scroll control knob a fifth time and fade will display. Turn the tune/scroll control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Music type button...

  • Page 249

    Program type 16-digit character display oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r & b sports sports talk talk top 40 top 40 weather weather by pushing th...

  • Page 250

    • dvd enter — when the disc is in dvd menu mode, selecting dvd enter will allow you to play the current highlighted selection. Use the remote control to scroll up and down the menu (if equipped). • disc play/pause — you can toggle between playing the dvd and pausing the dvd by pushing the select but...

  • Page 251

    • set home clock — pressing the select button allows you to set the clock. Turn the tune/scroll control knob to adjust the hours and then press and turn the tune/scroll control knob to adjust the minutes. Press the tune/scroll control knob again to save changes. • player defaults — selecting this it...

  • Page 252

    Audio drc — if equipped selecting this item allows you to limit maximum audio dynamic range. The default is set to ⬙high,⬙ and under this setting, dialogues will play at 11 db higher than if the setting is ⬙normal.⬙ aspect ratio — if equipped selecting this item allows you to choose between wide scr...

  • Page 253

    You may add a second station to each pushbutton by repeating the above procedure with this exception: push the set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am, 12 fm, and 12 satellite (if equipped)...

  • Page 254

    Note: the ignition switch must be in the on or acc position to operate the radio. Load button — loading compact disc(s) push the load button and the pushbutton with the corresponding number (1-6) where the cd is being loaded. The radio will display please wait and prompt when to insert disc. After t...

  • Page 255

    The current selection. Pushing and holding the seek button will allow you to scroll through the tracks faster in cd and mp3/mwa modes. Scan button (cd mode) push the scan button to scan through each track on the cd currently playing. Time button (cd mode) push this button to change the display from ...

  • Page 256

    The radio uses the following limits for file systems: • maximum number of directory levels: 8 • maximum number of files: 255 • maximum number of folders: 100 • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙.⬙ and a three- character extension) • level 2: 31 ...

  • Page 257

    Mpeg specification sampling frequency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48 wma specification sampling frequency (khz) bit rate (kbps) wma 44.1 and 48 48,...

  • Page 258

    To increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. List button — disc mode for mp3/wma play pushing the list button will bring up a list of all folders on t...

  • Page 259

    Note: the aux device must be turned on and the device’s volume set to the proper level. If the aux audio is not loud enough, turn the device’s volume up. If the aux audio sounds distorted, turn the device’s volume down. Seek button (auxiliary mode) no function. Scan button (auxiliary mode) no functi...

  • Page 260

    Dolby® manufactured under license from dolby® laboratories. Dolby® and the double-d symbol are trademarks of dolby® laboratories. Macrovision this product incorporates copyright protection technol- ogy that is protected by u.S. Patents and other intellec- tual property rights. Use of this copyright ...

  • Page 261

    Information, call the toll-free number 888-539-7474, or visit the sirius web site at www.Siriusxm.Com, or at www.Siriusxm.Ca for canadian residents. Electronic serial number/sirius identification number (esn/sid) please have the following information available when calling: 1. The electronic serial ...

  • Page 262

    Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or under a physical obstacle. • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or alon...

  • Page 263

    Additional three seconds will make the radio display the song title all of the time (push and hold again to return to normal display). Rw/ff pushing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) turn...

  • Page 264

    Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, push the set/rnd button. The symbol set 1 will now show in the display window. Select the button (1–6) you wish to lock onto this station and push and release that button. If ...

  • Page 265

    Uconnect® 130 operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electron...

  • Page 266

    Another selection. Holding either button will bypass stations without stopping, until you release it. Time button push the time button to alternate display of the time and radio frequency. Clock setting procedure 1. Push and hold the time button until the hours blink. 2. Adjust the hours by turning ...

  • Page 267

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 268

    You may add a second station to each pushbutton by repeating the above procedure with this exception: push the set/rnd button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored in...

  • Page 269

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 270

    Seek button push the right seek button for the next selection on the cd. Push the left seek button to return to the beginning of the current selection, or return to the beginning of the previous selection if the cd is within the first second of the current selection. Pushing and holding the seek but...

  • Page 271

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 272

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 273

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 274

    Uconnect® 130 with satellite radio operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn of...

  • Page 275

    Another selection. Holding either button will bypass stations without stopping, until you release it. Voice command system (radio) — if equipped refer to “voice command” in “understanding the fea- tures of your vehicle”. Voice command button uconnect® phone — if equipped push this button to operate ...

  • Page 276

    3. After adjusting the hours, push the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune/ scroll control knob. Push the tune/scroll con- trol knob to save time change. 5. To exit, push any button/knob or wait fiv...

  • Page 277

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 278

    Program type 16-digit character display classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc progra...

  • Page 279

    If a preset button is activated while in the music type (program type) mode, the music type mode will be exited and the radio will tune to the preset station. Setup button pushing the setup button allows you to select between the following items: • set clock — pushing the select button will allow yo...

  • Page 280

    Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to pushbutton memory (12 am and 12 fm stations). Disc/aux button pushing the disc/aux button will allow you to switch from am/fm modes to disc/au...

  • Page 281

    Caution! • this cd player will accept 4–3/4 inch (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. • do not use adhesive labels. These labels can peel away and jam the player mechanism. • the uconnect® 130 is a single cd player. Do not attempt to insert a second cd...

  • Page 282

    Rw/ff push and hold ff (fast forward) and the cd player will begin to fast forward until ff is released or rw or another cd button is pushed. The rw (reverse) button works in a similar manner. Am/fm button push the button to select either am or fm mode. Set/rnd button (random play button) push this ...

  • Page 283

    The radio uses the following limits for file systems: • maximum number of folder levels: 8 • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file ...

  • Page 284

    Use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bit rates. Mpeg specification sampling frequency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48...

  • Page 285

    To increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. List button — cd mode for mp3 play pushing the list button will bring up a list of all folders on the dis...

  • Page 286

    Note: the aux device must be turned on and the device’s volume set to the proper level. If the aux audio is not loud enough, turn the device’s volume up. If the aux audio sounds distorted, turn the device’s volume down. Time button (auxiliary mode) push this button to change the display to time of d...

  • Page 287

    To access the esn/sid, refer to the following steps: esn/sid access with the ignition switch in the on/run or acc posi- tion and the radio on, push the setup button and scroll using the tune/scroll control knob until sirius id is selected. Push the tune/scroll control knob and the sirius id number w...

  • Page 288

    Operating instructions — uconnect® (satellite) mode note: the ignition switch must be in the on/run or acc position to operate the radio. Seek buttons push and release the seek buttons to search for the next listenable station in am/fm mode. Push the right switch to seek up and the left switch to se...

  • Page 289

    Music type button pushing this button once will turn on the music type mode for five seconds. Pushing the music type button or turning the tune/scroll control knob within five seconds will allow the program format type to be se- lected. Toggle the music type button again to select the music type. By...

  • Page 290

    You may add a second channel to each pushbutton by repeating the above procedure with this exception: push the set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2. This allows a total of 12 satellite channels to be stored into pushbutton memory. The...

  • Page 291

    Connecting the ipod® or external usb device use the connection cable to connect an ipod® or external usb device to the vehicle’s usb/aux connector port which is located in the center console or glove compart- ment. Once the audio device is connected and synchronized to the vehicle’s ipod®/usb/mp3 co...

  • Page 292

    • the audio device can be controlled using the radio buttons to play, browse, and list the ipod® contents. • the audio device battery charges when plugged into the usb/aux connector (if supported by the specific audio device). Controlling the ipod® or external usb device using radio buttons to enter...

  • Page 293

    • jump backward in the current track by pushing and holding the rw button. Holding the rw button long enough will jump to the beginning of the current track. • jump forward in the current track by pushing and holding the ff >> button. • a single push backward rw or forward ff >> will jump backward o...

  • Page 294

    Device, or push the vr button and say ⬙shuffle on⬙ or ⬙shuffle off.⬙ if the rnd icon is showing on the radio display, then the shuffle mode is on. List or browse mode during play mode, pushing any of the buttons described below, will bring up list mode. List mode enables scrolling through the list o...

  • Page 295

    Pushing a preset button will display the current list on the top line and the first item in that list on the second line. To exit list mode without selecting a track, push the same preset button again to go back to play mode. List button: the list button will display the top level menu of the ipod® ...

  • Page 296

    Bluetooth® streaming audio (btsa) music can be streamed from your cellular phone to the uconnect® phone system. Refer to the uconnect® radio supplement for further information on bluetooth® connectivity. Controlling btsa using radio buttons to enter btsa mode, push either “aux” button on the radio o...

  • Page 297

    Browse browsing is not available on a bluetooth® streaming audio (btsa) device. Only the current song that is playing will display info. Steering wheel audio controls the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches...

  • Page 298

    Pushing the center button will make the radio switch between the various modes available (am/fm/sat/ cd/hdd/aux/ves, etc.). The left-hand control is a rocker-type switch with a pushbutton in the center. The function of the left-hand control is different depending on which mode you are in. The follow...

  • Page 299

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 300

    Climate controls the air conditioning and heating system is designed to make you comfortable in all types of weather. Manual heating and air conditioning the manual temperature controls consist of a series of outer rotary dials and inner push knobs. Manual temperature controls 298 understanding your...

  • Page 301

    Blower control rotate this control to regulate the amount of air forced through the ven- tilation system in any mode. The blower speed increases as you move the control to the right from the “o” (off) position. There are seven blower speeds. Temperature control rotate this control to regulate the te...

  • Page 302

    Note: the air conditioning compressor will not engage until the engine has been running for about 10 seconds. • max a/c for maximum cooling use the a/c and recirculation buttons at the same time. • economy mode if economy mode is desired, push the a/c button to turn off the indicator light and the a...

  • Page 303

    • bi-level air is directed through the panel and floor outlets. Note: for all settings, except full cold or full hot, there is a difference in temperature between the upper and lower outlets. The warmer air flows to the floor outlets. This feature gives improved comfort during sunny but cool conditi...

  • Page 304

    • recirculation control pushing the recirculation control button will put the system in recirculation mode. This can be used when outside conditions such as smoke, odors, dust, or high humidity are pres- ent. Activating recirculation will cause the led in the control button to illuminate. Note: • co...

  • Page 305

    Automatic temperature control (atc) — if equipped the automatic temperature control system automati- cally maintains the climate in the cabin of the vehicle at the comfort levels desired by the driver and passenger. Automatic operation operation of the system is quite simple. 1. Turn the mode contro...

  • Page 306

    You will experience the greatest efficiency by simply allowing the system to function automatically. Selecting the “o” (off) position on the blower control stops the system completely and closes the outside air intake. The recommended setting for maximum comfort for the average person is 72°f (22°c)...

  • Page 307

    Manual operation override this system offers a full complement of manual override features, which consist of blower preferred automatic, mode preferred automatic, or blower and mode pre- ferred automatic. This means the operator can override the blower, the mode, or both. There is a manual blower ra...

  • Page 308

    306 understanding your instrument panel.

  • Page 309

    The operator can override the auto mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions. • panel air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. Note: the center ...

  • Page 310

    • air conditioner control push this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the mode control dial. Push this but- ton a second time to turn off the air conditioning....

  • Page 311

    • most of the time, when in automatic operation, you can temporarily put the system into recirculation mode by pushing the recirculation button. However, under certain conditions, while in automatic mode, the system is blowing air out the defrost vents. When these conditions are present, and the rec...

  • Page 312

    Winter operation use of the air recirculation mode during winter months is not recommended because it may cause window fogging. Vacation storage anytime you store your vehicle, or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for about five mi...

  • Page 313

    Outside air intake make sure the air intake, located directly in front of the windshield, is free of obstructions such as leaves. Leaves collected in the air intake may reduce airflow, and if they enter the plenum, they could plug the water drains. In winter months, make sure the air intake is clear...

  • Page 314

    Control setting suggestions for various weather conditions 312 understanding your instrument panel.

  • Page 315

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .317 ▫ manual transmission — if equipped . . . . . . .317 ▫ automatic transmission — if equipped . . . . .318 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .318 ▫ extreme cold weather (below –20°f or −...

  • Page 316

    䡵 autostick . . . . . . . . . . . . . . . . . . . . . . . . . .339 ▫ autostick (six-speed automatic transmission) . .339 ▫ autostick (cvt) . . . . . . . . . . . . . . . . . . . . . .341 䡵 four-wheel drive operation — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .343 䡵 on-road driv...

  • Page 317

    䡵 tire safety information . . . . . . . . . . . . .371 ▫ tire markings . . . . . . . . . . . . . . . . . . . . . . . .371 ▫ tire identification number (tin). . . . . . . . . . .375 ▫ tire terminology and definitions . . . . . . . . . .376 ▫ tire loading and tire pressure . . . . . . . . . . .378 䡵 t...

  • Page 318

    ▫ reformulated gasoline . . . . . . . . . . . . . . . . .407 ▫ gasoline/oxygenate blends . . . . . . . . . . . . . .407 ▫ e-85 usage in non-flex fuel vehicles . . . . . . .408 ▫ mmt in gasoline . . . . . . . . . . . . . . . . . . . . .408 ▫ materials added to fuel . . . . . . . . . . . . . . . .408 ...

  • Page 319

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park, and re- move the key fob from the ignition. When leaving the ...

  • Page 320

    Automatic transmission — if equipped the shift lever must be in the park or neutral position before you can start the engine. Depress the brake pedal before shifting to any driving gear. Note: you must press the brake pedal before shifting out of park. Tip start do not press the accelerator. Turn th...

  • Page 321

    Warning! (continued) another vehicle. This type of start can be dangerous if done improperly, so follow the procedure carefully. Refer to “jump starting” in “what to do in emer- gencies” for further information. Extreme cold weather (below –20°f or −29°c) to ensure reliable starting at these tempera...

  • Page 322

    Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. The engine block heater must be plugged in at least one hour to have an...

  • Page 323

    Use each gear in numerical order, do not skip a gear. Be sure the transmission is in first gear, (not third), when starting from a standing position. Damage to the clutch can result from starting in a gear higher than first gear. Caution! • launching in any gear except 1st gear will result in excess...

  • Page 324

    Never shift into reverse until the vehicle has come to a complete stop. Note: during cold weather, until the transmission lu- bricant is warm, you may experience slightly higher shift efforts. This is normal and not harmful to the transmis- sion. Recommended shift speeds to use your manual transmiss...

  • Page 325

    Downshifting proper downshifting will improve fuel economy and prolong engine life. Caution! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released. Damage...

  • Page 326

    Note: you must press and hold the brake pedal while shifting out of park. Warning! • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You c...

  • Page 327

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 328

    Brake/transmission shift interlock system this vehicle is equipped with a brake transmission shift interlock system (btsi) that holds the shift lever in park unless the brakes are applied. To shift the transmission out of park, the ignition switch must be turned to the on/run position (engine runnin...

  • Page 329

    Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park (p) this range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to...

  • Page 330

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 331

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 332

    • look at the transmission gear position display and verify that it indicates the park position (p). • with brake pedal released, verify that the shift lever will not move out of park. Reverse (r) this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a ...

  • Page 333

    Drive (d) this range should be used for most city and highway driving. It provides the smoothest upshifts and down- shifts, and the best fuel economy. The transmission automatically upshifts through underdrive first, second, third, and fourth gears, direct fifth gear and overdrive sixth gear. The dr...

  • Page 334

    Mode is activated. In this mode, the transmission remains in fourth gear regardless of which forward gear is selected. Park, reverse, and neutral will continue to operate. The malfunction indicator light (mil) may be illuminated. Limp home mode allows the vehicle to be driven to an authorized dealer...

  • Page 335

    • the transmission fluid has reached an adequate tem- perature. • the engine coolant has reached an adequate tempera- ture. • the vehicle speed is sufficiently high. • the driver is not heavily pressing the accelerator. Torque converter clutch a feature designed to improve fuel economy has been incl...

  • Page 336

    Note: the continuously variable automatic transmis- sion (cvt) changes ratios in a continuous manner. This may sometimes ⬙feel⬙ as if it is slipping, but this is normal and does not harm anything. Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle is stop...

  • Page 337

    When parking on a hill, apply the parking brake before shifting the transmission to park, otherwise the load on the transmission locking mechanism may make it diffi- cult to move the shift lever out of park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away f...

  • Page 338

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and r...

  • Page 339

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off position to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ...

  • Page 340

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 341

    During sustained high speed driving or trailer towing up long grades on hot days, the auto- matic transmission oil may become too hot. If this happens, the transmission overheat indica- tor light will come on, and the vehicle will slow slightly until the transmission cools down enough to allow a ret...

  • Page 342

    (+) to enter autostick mode will retain the current gear. When autostick is active, the current transmission gear is displayed in the instrument cluster. In autostick mode, the transmission will shift up or down when the driver moves the shift lever to the right (+) or left (-), unless an engine lug...

  • Page 343

    To disengage autostick mode, hold the shift lever to the right (+) until “d” is once again displayed in the instru- ment cluster. You can shift in or out of the autostick mode at any time without taking your foot off the accelerator pedal. Warning! Do not downshift for additional engine braking on a...

  • Page 344

    In autostick mode, the transmission will shift up or down when (+/-) is manually selected by the driver, unless an engine lugging or overspeed condition would result. It will remain in the selected gear until another upshift or downshift is chosen, except as described below: • the transmission will ...

  • Page 345

    Four-wheel drive operation — if equipped this feature provides full time, on-demand, four–wheel drive (4wd). Where one or more wheels have wheel spin or if addi- tional traction is needed in sand, deep snow, or loose traction surfaces, activate the “4wd lock” switch by pulling up once and releasing....

  • Page 346

    An advantage of the higher ground clearance is a better view of the road, allowing you to anticipate problems. They are not designed for cornering at the same speeds as conventional two-wheel drive vehicles any more than low-slung sports cars are designed to perform satisfacto- rily in off-road cond...

  • Page 347

    Warning! Always wear your seat belt and firmly tie down cargo. Unsecured cargo can become projectiles in an off-road situation. When to use low (l off-road) with the 4wd lock lever engaged when driving off-road, shift into low (l off-road) and activate the 4wd lock. This will provide additional trac...

  • Page 348

    Snow in heavy snow or for additional control and traction at slower speeds, activate the 4wd lock and shift the transaxle to low (l off-road) if necessary. Do not shift to a lower gear than necessary to maintain headway. Over- revving the engine can spin the wheels and traction will be lost. If you ...

  • Page 349

    Sand soft sand is very difficult to travel through with full tire pressure. When crossing soft sandy spots in a trail maintain your vehicle’s momentum and do not stop. The key to driving in soft sand is using the appropriate tire pressure, accelerating slowly, avoiding abrupt maneu- vers and maintai...

  • Page 350

    Before climbing a steep hill as you approach a hill consider its grade or steepness. Determine if it is too steep. Look to see what the traction is on the hill side trail. Is the trail straight up and down? What is on top and the other side? Are there ruts, rocks, branches or other obstacles on the ...

  • Page 351

    Driving down hill before driving down a steep hill you need to determine if it is too steep for a safe descent. What is the surface traction? Is the grade too steep to maintain a slow controlled descent? Are there obstacles? Is it a straight descent? Is there plenty of distance at the base of the hi...

  • Page 352

    If you stall or begin to lose headway if you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake. Restart the engine and shift to reverse. Back slowly down the hill allowing engine and hill descent braking to control the de...

  • Page 353

    Caution! Water ingestion into the transaxle, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water. Water can cause permanent damage to engine, driveline or other vehicle components and your brakes will be less effective once wet and/or muddy. Before ...

  • Page 354

    Caution! Muddy waters can reduce the cooling system effec- tiveness by depositing debris onto the radiator. After driving off-road off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road, it is always a good idea to check for damage. That way you can ...

  • Page 355

    Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent a collision. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. • if y...

  • Page 356

    Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. Power steering fluid check checking the power steering fluid level at a define...

  • Page 357

    Parking brake before leaving the vehicle, make sure that the parking brake is fully applied. Also, be certain to leave an automatic transmission in park, or manual transmission in reverse or first gear. The parking brake lever is located in the center console. To apply the parking brake, pull the le...

  • Page 358

    Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • this light only shows that ...

  • Page 359

    Warning! (continued) • always fully apply the parking brake when leav- ing your vehicle or it may roll and cause damage or injury. Also, be certain to leave an automatic trans- mission in park, a manual transmission in re- verse or first gear. Failure to do so may cause the vehicle to roll and cause...

  • Page 360

    If either of the two hydraulic systems lose normal capa- bility, the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop. In addition, if the malfuncti...

  • Page 361

    Warning! • pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • the abs cannot prevent the natural laws of phys- ics from acting on the ve...

  • Page 362

    If the “abs warning light” is on, the brake system should be serviced as soon as possible to restore the benefits of anti-lock brakes. If the “abs warning light” does not come on when the ignition switch is turned to the on position, have the bulb repaired as soon as possible. If both the “brake war...

  • Page 363

    Warning! The anti-lock brake system (abs) contains sophis- ticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This in- terference can cause possible loss of anti-lock brak- ing capability. Installation of s...

  • Page 364

    Benefit of the system, you must apply continuous brak- ing pressure during the stopping sequence (do not “pump” the brakes). Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the bas is deactivated. Warning! • the brake assist system (bas) cann...

  • Page 365

    Note: anytime the esc system is in the “full off” mode, erm is disabled. Refer to “electronic stability control (esc)” in this section for a complete explanation of the available esc modes. Warning! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance...

  • Page 366

    Off” button for five seconds. Refer to “electronic stability control (esc)” in this section of the manual. Hdc operation can be overridden with brake application to slow the vehicle down below the hdc control speed. Conversely, if more speed is desired during hdc control, the accelerator pedal will ...

  • Page 367

    Hsa activation criteria the following criteria must be met in order for hsa to activate: • vehicle must be stopped. • vehicle must be on a 7% (approximate) grade or greater hill. • gear selection matches vehicle uphill direction (i.E., vehicle facing uphill is in forward gear; vehicle back- ing uphi...

  • Page 368

    5. Release the clutch pedal (if equipped). 6. Rotate the steering wheel one-half turn to the left. 7. Press the “esc off” switch (located in the lower switch bank below the climate controls) four times within 20 seconds. The “esc activation/malfunction indicator light” should turn on and turn off tw...

  • Page 369

    Warning! • the electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. • esc cannot prevent accidents, including those re- sulting from excessive speed in turns, driving on ve...

  • Page 370

    Indicator light ⬙ will be illuminated. All other stability features of esc function normally. This mode is intended to be used if the vehicle is in deep snow, sand or gravel conditions and more wheel spin than esc would nor- mally allow is required to gain traction. To turn esc on again, momentarily...

  • Page 371

    Light ⬙ will illuminate and the “esc off” message will appear in the odometer. Push and release the trip odom- eter button located on the instrument cluster to clear this message. In this mode, esc and tcs, except for the “limited slip” feature described in the tcs section, are turned off until the ...

  • Page 372

    Esc activation/malfunction indicator light and esc off indicator light the “esc activation/malfunction indicator light” in the instrument cluster will come on when the ignition switch is cycled to the on/ run position. It should go out with the engine running. If the “esc activation/malfunction indi...

  • Page 373

    • the esc system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when esc becomes inactive following the maneuver that caused the esc activation. The “esc off indicator light” indicates the electronic stability control (esc) is partially off or full off. ...

  • Page 374

    Note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design standards. Tires designed to this standard ...

  • Page 375

    Tire sizing chart example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on u.S. Design standards, or ⴖ....Blank....ⴖ = passenger car tire based on european design standards, or lt = light truck tire based o...

  • Page 376

    Example: service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – the maximum speed corres...

  • Page 377

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 378

    Example: dot ma l9 abcd 0301 – 01 means the year 2001 – prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured. Example: 031 could represent the 3rd week of 1981 or 1991 tire terminology and definitions term definition b-...

  • Page 379

    Term definition pressure is molded into the sidewall. Recommended cold tire inflation pressure vehicle manufacturer’s recommended cold tire inflation pres- sure as shown on the tire placard. Tire placard a label permanently attached to the vehicle describing the ve- hicle’s loading capacity, the ori...

  • Page 380

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) example tire placard location (b-pillar) 378 starting an...

  • Page 381

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 382

    To determine the maximum loading conditions of your vehicle, locate the statement “the combined weight of occupants and cargo should never exceed xxx lbs or xxx kg” on the tire and loading information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) ...

  • Page 383

    Note: • if your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. The follow- ing table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and num- ber and size of occupan...

  • Page 384

    382 starting and operating.

  • Page 385

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 386

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the v...

  • Page 387

    At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judgement when determining proper inflation. Tires may look properly inflated even when they are under- inflated. • inspect tires for signs of tire wear or visible damage. Cau...

  • Page 388

    Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too low. Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits ...

  • Page 389

    Tire repair if your tire becomes damaged, it may be repaired if it meets the following criteria: • the tire has not been driven on when flat. • the damage is only on the tread section of your tire (sidewall damage is not repairable). • the puncture is no greater than a ¼ of an inch (6 mm). Consult a...

  • Page 390

    Summer tires do not contain the all season designation or mountain/snowflake symbol on the tire sidewall. Use summer tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Warning! Do not use summer tires in snow/ice conditions. You could lose vehi...

  • Page 391

    While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states pro- hibit studded tires; therefore, local laws should be checked before using these tire types. Run flat tires — if equipped run flat tires a...

  • Page 392

    Rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended tire rotation pattern. Compact spare tire — if equipped the compact spare is for temporary emergency use only. You can identify if your vehicle is equipped with a compact spare by looki...

  • Page 393

    Full size spare — if equipped the full size spare is for temporary emergency use only. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, the ...

  • Page 394

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping. Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Warning! Fast spinning ti...

  • Page 395

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information. L...

  • Page 396

    Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressures. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance when ...

  • Page 397

    Warning! (continued) • never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have a collision. • failure to equip your vehicle wi...

  • Page 398

    These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires. Rotation will increase tread life, help to maintain mud, snow and wet traction levels, and contribute to a smooth, quiet ...

  • Page 399

    The tire pressure will vary with temperature by about 1 psi (7.0 kpa) for every 12°f (6.5°c). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on “cold inflation tire pressure”. This is defined as the tire pressure afte...

  • Page 400

    For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 30 psi (207 kpa). If the ambient temperature is 68°f (20°c) and the measured tire pressure is 27 psi (186 kpa), a temperature drop to 20°f (-7°c) will decrease the tire pressure to approximat...

  • Page 401

    Caution! (continued) • after inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the tire pressure moni- toring sensor. Note: • the tpms is not intended to replace normal tire care and ma...

  • Page 402

    Note: it is particularly important for you to check the tire pressure in all of the tires on your vehicle regularly and to maintain the proper pressure. The tpms consists of the following components: • receiver module. • four tire pressure monitoring sensors. • tire pressure monitoring telltale ligh...

  • Page 403

    2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with tpm sensors. Note: your vehicle is equipped with a compact spare wheel and tire asse...

  • Page 404

    Premium system — if equipped the tpms uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver module. Note: it is particularly important for you to ch...

  • Page 405

    Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible and inflate all tires that are flashing on the graphic display to the vehicle’s recommended cold placard pres- sure value. The system will automatically update, the “low tire” text message w...

  • Page 406

    If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the tire pressure monitoring telltale light will no longer flash, the ⬙service tpm system⬙ text message will not be present, and a pressure value will be displayed...

  • Page 407

    Pressure values still shown. This indicates that the pres- sure values are still being received from the tpm sensors but they may not be located in the correct vehicle position. The system still needs to be serviced as long as the ⬙service tpm system⬙ message is displayed. Note: your vehicle is equi...

  • Page 408

    Long as no tire pressure is below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this information. General information this device complies with part 15 of the fcc rul...

  • Page 409

    Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations. If you experience these symptoms, try another brand of gasoline before consid- ering service for the vehicle. Reformulated gasoline many areas of the country require the use of cleaner burning gasoline referre...

  • Page 410

    E-85 usage in non-flex fuel vehicles non-flex fuel vehicles (ffv) are compatible with gaso- line containing up to 10% ethanol (e10). Gasoline with higher ethanol content may void the new vehicle lim- ited warranty. If a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have som...

  • Page 411

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gasoline is prohibited by federal law. Using leaded gasoline can impair engine per- formance and damage the emissions control sys- tem. • an out-of-tune engine or certain fuel or ignitio...

  • Page 412

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 413

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel tank filler cap. A poorly fitting cap could let impurities into the fuel system. • a poorly fitting fuel filler cap may cause the “malfunction indicator light (mil)” to turn on. • to avoid fuel s...

  • Page 414

    Warning! • never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the mil to turn on. • a fire may result if gaso...

  • Page 415

    Vehicle loading as required by national highway traffic safety admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or b-pillar. Vehicle certification label your vehicle has a vehicle certification label attached to the driver’s door b-pillar. The la...

  • Page 416

    Inflation pressure this is the cold tire inflation pressure for your vehicle for all loading conditions up to full gawr. Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants ...

  • Page 417

    Trailer towing in this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible. To maintain the new vehicle limited war...

  • Page 418

    Gross axle weight rating (gawr) the gawr is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear gawr. Refer to “vehicle loading/vehicle certifica- tion label” in “starting and operating” for...

  • Page 419

    Weight-carrying hitch a weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle. These kinds of hitches are the most popular on the market today and they are commonly used to tow small and medium sized...

  • Page 420

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer hitch classification definitions clas...

  • Page 421

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/transmission frontal area maximum gtw (gross trailer wt.) maximum tongue wt. (see note) 2.0l auto/man 22 sq ft (2.04 sq m) 1,000 lbs (450 ...

  • Page 422

    Cause the trailer to sway severely side to side which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer collisions. Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items...

  • Page 423

    Towing requirements to promote proper break-in of your vehicle drivetrain components, the following guidelines are recommended: caution! • do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • then, during the f...

  • Page 424

    Warning! (continued) • safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • vehicles with trailers should not be parke...

  • Page 425

    Towing requirements — tires • do not attempt to tow a trailer while using a compact spare tire. • proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to “tires – general information” in “starting and oper- ating” for proper tire inflation proce...

  • Page 426

    Warning! • do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have a collision. • towing any trailer will increase your stopping distance. When towing you should allow f...

  • Page 427

    Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground 2 — backup lamps 6 — left stop/turn 3 — right stop/turn 7 — running lamps 4 — electric brakes 5 starting and operating 425.

  • Page 428

    Towing tips before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Manual transmission — if equipped if using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippag...

  • Page 429

    To prevent excess heat generation, avoid continuous driving at high rpm. Reduce vehicle speed as necessary to avoid extended driving at high rpm. Return to a higher gear or vehicle speed when grade and road conditions allow. Electronic speed control — if equipped • do not use in hilly terrain or wit...

  • Page 430

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmission automatic transmission flat tow none • transmission in neu- tral • key in acc position not allowed dolly tow front ok (fwd only) ok (fwd only) rear not a...

  • Page 431

    Note: vehicles equipped with manual transmissions may be recreationally towed (flat towed) at any legal highway speed, for any distance, if the manual transmis- sion is in neutral and the ignition key is in the acc position. Caution! • do not flat tow any vehicle equipped with an automatic transmiss...

  • Page 433

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .433 䡵 if your engine overheats . . . . . . . . . . . .433 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .434 ▫ torque specifications . . . . . . . . . . . . . . . . . .434 䡵 jacking a...

  • Page 434

    䡵 shift lever override . . . . . . . . . . . . . . . .463 䡵 towing a disabled vehicle . . . . . . . . . . .464 ▫ with ignition key . . . . . . . . . . . . . . . . . . . . .466 432 what to do in emergencies.

  • Page 435

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the climate controls. Push the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency....

  • Page 436

    Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the n...

  • Page 437

    **use only your authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tig...

  • Page 438

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to...

  • Page 439

    Jack location the jack and jack-handle are stowed under the load floor in the cargo area. Spare tire stowage the compact spare tire is stowed under the rear load floor in the cargo area. Spare tire removal lift up the load floor cover and remove the hold down. Preparations for jacking 1. Park the ve...

  • Page 440

    2. Turn on the hazard warning flasher. 3. Set the parking brake. 4. Place the shift lever in park (automatic transmission) or reverse (manual transmission). 5. Turn off the ignition. 6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing t...

  • Page 441

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 442

    1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench and remove the wrench from the jack assembly. Note: the jack handle attaches to the side of the jack with two attachment points. When the jack is partially expande...

  • Page 443

    Note: there are front and rear jacking locations on each side of the body. The front locations are outlined by two triangular cutouts on one of the flanges in the sill flange assembly. The rear location is the same but with two rectangular cutouts. For vehicles equipped with plastic trim, the plasti...

  • Page 444

    Front jacking location rear jacking location 442 what to do in emergencies.

  • Page 445

    Do not raise the vehicle until you are sure the jack is securely engaged. 3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to th...

  • Page 446

    Caution! Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damaged if the spare tire is mounted incorrectly. Warning! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. Note: the wheel cover is held on th...

  • Page 447

    8. Remove the wheel blocks and lower the jack until it is free. Release the parking brake. Reassemble the lug wrench to the jack assembly and stow it in the spare tire area. Secure the assembly using the means pro- vided. Warning! A loose tire or jack thrown forward in a collision or hard stop could...

  • Page 448

    Road tire installation vehicles equipped with wheel covers 1. Mount the road tire on the axle. 2. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand. Do not use a hammer or excessive force to install the cover. Tire and wheel cover or center cap 1 — ...

  • Page 449

    3. Install the five wheel lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in se...

  • Page 450

    5. After 25 miles (40 km) check the lug nut torque with a torque wrench to ensure that all lug nuts are properly seated against the wheel. Tire service kit — if equipped small punctures up to ¼” (6 mm) in the tire tread can be sealed with tire service kit. Foreign objects (e.G., screws or nails) sho...

  • Page 451

    Using the mode select knob and hoses your tire service kit is equipped with the following symbols to indicate the air or sealant mode. Selecting air mode push in the mode select knob (5) and turn to this position for air pump operation only. Use the black air pump hose (7) when selecting this mode. ...

  • Page 452

    • the sealant bottle (1) and sealant hose (6) are a one tire application use and need to be replaced after each use. Always replace these components immediately at your original equipment vehicle dealer. • when the tire service kit sealant is in a liquid form, clean water, and a damp cloth will remo...

  • Page 453

    Warning! • do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the tire service kit. • do not use tire service kit or drive the vehicle under the following circumstances: – if the puncture in the tire t...

  • Page 454

    Warning! (continued) • tire service kit sealant solution contains latex. In case of an allergic reaction or rash, consult a phy- sician immediately. Keep tire service kit out of reach of children. If swallowed, rinse mouth imme- diately with plenty of water and drink plenty of water. Do not induce v...

  • Page 455

    4. Remove the cap from the valve stem and then screw the fitting at the end of the sealant hose (6) onto the valve stem. 5. Uncoil the power plug (8) and insert the plug into the vehicle’s 12 volt power outlet. Note: do not remove foreign objects (e.G., screws or nails) from the tire. (c) injecting ...

  • Page 456

    Note: if the mode select knob (5) is on air mode and the pump is operating, air will dispense from the air pump hose (7) only, not the sealant hose (6). If the sealant (white fluid) does flow through the sealant hose (6): 1. Continue to operate the pump until sealant is no longer flowing through hos...

  • Page 457

    3. Immediately disconnect the sealant hose (6) from the valve stem, reinstall the cap on the fitting at the end of the hose, and place the tire service kit in the vehicle storage location. Quickly proceed to (d) “drive ve- hicle.” caution! • the metal end fitting from power plug (8) may get hot afte...

  • Page 458

    (e) after driving: pull over to a safe location. Refer to “whenever you stop to use tire service kit” before continuing. 1. Push in the mode select knob (5) and turn to the air mode position. 2. Uncoil the power plug and insert the plug into the vehicle’s 12 volt power outlet. 3. Uncoil the air pump...

  • Page 459

    5. Remove the speed limit sticker from the instrument panel after the tire has been repaired. 6. Replace the sealant bottle (1) and sealant hose (6) assembly at your authorized dealer as soon as pos- sible. Refer to (f) “sealant bottle and hose replace- ment”. Note: when having the tire serviced, ad...

  • Page 460

    Pack. Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully. Note: when using a portable battery booster pack follow the manufacturer’s operating instructions and precautions. Caution! Do not use a portable battery booster pack or any other boost...

  • Page 461

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 462

    3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is off. Warning! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-start...

  • Page 463

    4. Connect the opposite end of the negative (-) jumper cable to a good engine ground (exposed metal part of the discharged vehicle’s engine) away from the battery and the fuel injection system. Warning! Do not connect the jumper cable to the negative (-) post of the discharged battery. The resulting...

  • Page 464

    If frequent jump-starting is required to start your vehicle you should have the battery and charging system in- spected at your authorized dealer. Caution! Accessories plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Ev...

  • Page 465

    Note: push the ⬙esc off⬙ switch, to place the electronic stability control (esc) system in ⬙partial off⬙ mode, before rocking the vehicle. Refer to “electronic brake control” in “starting and operating” for further infor- mation. Once the vehicle has been freed, push the ⬙esc off ⬙ switch again to r...

  • Page 466

    3. Using a small screwdriver or similar tool, remove the shift lever override access cover (located on the right side of the shift lever housing). 4. Turn the ignition switch to the acc or on/run position, but do not start the engine. 5. Push and maintain firm pressure on the brake pedal. 6. Insert ...

  • Page 467

    Towing con- dition wheels off the ground manual trans- mission 6-speed auto- matic (fwd only) 6-speed auto- matic 4wd cvt automatic transmission flat tow none • transmission in neutral • key in acc or on/run po- sition if transmission is operable: • transmission in neutral • 25 mph (40 km/h) max spe...

  • Page 468

    With ignition key automatic transmission • front wheel drive (fwd) vehicles can be towed with the front wheels elevated, or on a flatbed truck (all four wheels off the ground). • four-wheel drive (4wd) vehicles can be towed on a flatbed truck (all four wheels off the ground). If the transmission is ...

  • Page 469

    Caution! • do not flat tow any vehicle equipped with a cvt automatic transmission. Damage to the drive- train will result. If these vehicles require towing, make sure all drive wheels are off the ground. • towing this vehicle in violation of the above re- quirements can cause severe transmission and...

  • Page 470

    Caution! (continued) • towing this vehicle in violation of the above re- quirements can cause severe engine, transmission, or drivetrain damage. Damage from improper tow- ing is not covered under the new vehicle limited warranty. All transmissions if you must use the accessories (wipers, defroster, ...

  • Page 471

    Maintaining your vehicle contents 䡵 engine compartment — 2.0l . . . . . . . . . .471 䡵 engine compartment — 2.4l . . . . . . . . . .472 䡵 onboard diagnostic system — obd ii . .473 ▫ loose fuel filler cap message . . . . . . . . . . . .473 䡵 emissions inspection and maintenance programs . . . . . . ....

  • Page 472

    ▫ automatic transmission (six-speed) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .498 ▫ automatic transmission (cvt) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .500 ▫ manual transmission — if equipped . . . . . . .501 ▫ rear drive assembly (rda) — awd/4wd mod...

  • Page 473

    Engine compartment — 2.0l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 7 maintaining your vehicle 47...

  • Page 474

    Engine compartment — 2.4l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 472 maintaining your vehicle.

  • Page 475

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 476

    Persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the mil. Resolving the problem will turn the mil light off. Emissions inspection and maintenance programs in some localities, ...

  • Page 477

    3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 478

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 479

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, power steering...

  • Page 480

    Caution! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Also, be sure the oil fill cap is replaced and tightened after adding oil. Change engine oil the oil change i...

  • Page 481

    Caution! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the new vehicle limited warranty. Engine oil viscosity (sae grade) mopar® sae 5w-20 engine oil or equivalent pennzoil® or shell helix® is recommended for all operating tem- ...

  • Page 482

    Station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection this manufacturer’s engines have a full-flow ...

  • Page 483

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 484

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be ...

  • Page 485

    Caution! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air condi- tioning components. Such damage is not covered by the new vehicle limited warranty. Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) t...

  • Page 486

    4. Disengage the two retaining tabs that secure the filter cover to the hvac housing, and remove the cover. 5. Remove the a/c air filter by pulling it straight out of the housing. 6. Install the a/c air filter with the arrow on the filter pointing toward the floor. When installing the filter cover, ...

  • Page 487

    Should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mecha- nism and safety catch sh...

  • Page 488

    When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades, this will help blade performance. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperat...

  • Page 489

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips/exhaust gas” in “things to know before starting your vehicle” for further...

  • Page 490

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 491

    Cooling system warning! • when working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at any time the ignition switch is in the on position. • you or others can be badly burned by hot engin...

  • Page 492

    Cooling system — drain, flush and refill note: some vehicles require special tools to add coolant properly. Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system please contact your local authorized dealer. If the engin...

  • Page 493

    Caution! (continued) • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • this vehicle has not been designed for use with...

  • Page 494

    • use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain ...

  • Page 495

    Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To pre...

  • Page 496

    Long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicle is ...

  • Page 497

    • do not change the thermostat for summer or winter operation. If replacement is ever necessary, install only the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emis- sions. Brake system in order to assure ...

  • Page 498

    Note: if your vehicle is equipped with a manual transmission , the brake fluid reservoir supplies fluid to both the brake system and the clutch release system. The two systems are separated in the reservoir, and a leak in one system will not affect the other system. The manual transmission clutch re...

  • Page 499

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 500

    Automatic transmission (six-speed) — if equipped selection of lubricant (six-speed transmission) it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s specified transmission fluid. Refer to “fluids, lubricants, and genui...

  • Page 501

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating cond...

  • Page 502

    Automatic transmission (cvt) — if equipped selection of lubricant (cvt) it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s specified transmission fluid which has the special friction coefficient additives neces- sary ...

  • Page 503

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating cond...

  • Page 504

    Fluid level check check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more than 3/16 inch (4.7 mm) below the bottom of the hole. Add fluid, if necessary, to maintain the proper level. Please see your authorized dealer for ser...

  • Page 505

    Power transfer unit (ptu) — awd/4wd models only lubricant selection use only the manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in “maintain- ing your vehicle” for further information. Fluid level check visually inspect the unit at each oil change for leakage. If ...

  • Page 506

    What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road salt, dirt and moisture accumulation. • stone and gravel impact. • insects, tree sap and tar. • salt in the air near seacoast localities. ...

  • Page 507

    Special care • if you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • it is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open. • if you detect any stone chips or scratches...

  • Page 508

    Note: if your vehicle is equipped with dark vapor or black satin chrome wheels do not use wheel cleaners, abrasives or polishing compounds. They will perma- nently damage this finish and such damage is not cov- ered by the new vehicle limited warranty. Use only mild soap and water with a soft cloth....

  • Page 509

    Interior care use mopar® total clean to clean fabric upholstery and carpeting. Use mopar® total clean to clean vinyl upholstery. Mopar® total clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small part...

  • Page 510

    Caution! Do not use alcohol and alcohol-based and/or keton based cleaning products to clean leather seats, as damage to the seat may result. Cleaning headlights your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratc...

  • Page 511

    Instrument panel bezels caution! When installing hanging air fresheners in your ve- hicle, read the installation instructions carefully. Some air fresheners will damage the finish of painted or decorated parts if allowed to directly contact any surface. Cleaning plastic instrument cluster lenses the...

  • Page 512

    Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced a...

  • Page 513

    Warning! (continued) • if a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. Integrated power module (ipm) the integrated power module is located in the engine compa...

  • Page 514

    Cavity cartridge fuse mini-fuse description 3 10 amp red rear center brake light switch 4 10 amp red ignition switch/occupant classification module 5 15 amp lt blue battery feed for power tech 6 10 amp red power mirror/steering control satellite radio/ hands-free phone 7 30 amp green ignition off dr...

  • Page 515

    Cavity cartridge fuse mini-fuse description equipped 13 20 amp yellow cigar lighter 14 10 amp red instrument cluster 15 40 amp green radiator fan 16 15 amp lt blue dome lamp/sunroof/ rear wiper motor 17 10 amp red wireless control module 18 40 amp green auto shutdown relay 19 20 amp yellow radio amp...

  • Page 516

    Cavity cartridge fuse mini-fuse description equipped 25 10 amp red heated mirror – if equipped 26 15 amp lt blue auto shutdown relay 27 10 amp red airbag control module 28 10 amp red airbag control module/ occupant classification module 29 hot car (no fuse re- quired) 30 20 amp yellow heated seat – ...

  • Page 517

    Cavity cartridge fuse mini-fuse description control module 34 30 amp pink antilock brakevalve 35 40 amp green antilock brake pump 36 30 amp pink headlamp/washer control/smart glass – if equipped 37 25 amp clear diesel heater and h2/ mod power top caution! • when installing the ipm cover, it is impor...

  • Page 518

    Vehicle storage if you will not be using your vehicle for more than 21 days, you may want to take steps to preserve your battery. • disengage the mini-fuse in the power distribution center labeled iod (ignition off-draw). • or disconnect the negative cable from the battery. • anytime you store your ...

  • Page 519

    Exterior bulbs bulb number low beam headlamp h11 premium low beam headlamp hir2 high beam headlamp 9005 premium high beam headlamp hir2 premium front park lamp 3157k front park/turn signal lamp 7444na front side marker lamp 194 front fog lamp h11ll center high mounted stop lamp (chmsl) led assembly ...

  • Page 520

    Bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Headlamps 1. Raise the hood and loc...

  • Page 521

    Rear turn signal and backup lamp 1. Remove the two push-pins from the taillamp housing. 2. Grasp the taillamp and pull firmly to disengage the lamp from the aperture panel. 3. Twist and remove socket from lamp. 4. Remove bulb from socket and replace. License lamps 1. Use a screw driver to gently pry...

  • Page 522

    Fluid capacities u.S. Metric fuel (approximate) 13.6 gallons 51 liters engine oil with filter 2.0l and 2.4l engine (sae 5w-20, api certified) 4.5 quarts 4.26 liters cooling system * 2.0l and 2.4l engine (mopar® antifreeze/engine coolant 10 year/150,000 mile formula or equivalent) 7.2 quarts 6.8 lite...

  • Page 523

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of chrysler material standard ms.90032. Engine ...

  • Page 524

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 525

    Chassis component fluid, lubricant, or genuine part automatic transmission (cvt) — if equipped use only mopar® cvtf+4® continuously variable transmission fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Automatic transmission (six-spe...

  • Page 527

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . . .526 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .528 8.

  • Page 528

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 529

    Severe duty all models change engine oil at 4,000 miles (6,500 km) if the vehicle is operated in a dusty and off road environment. This type of vehicle use is considered severe duty. Once a month or before a long trip: • check engine oil level • check windshield washer fluid level • check the tire i...

  • Page 530

    Maintenance chart refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 ...

  • Page 531

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 532

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 533

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 534

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 535

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .535 ▫ prepare for the appointment. . . . . . . . . . . . .535 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .535 ▫ be reasonable with requests ....

  • Page 536

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .541 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .541 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .541 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .542 534 if...

  • Page 537

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 538

    This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer. They want to know if you need assistance. • if an autho...

  • Page 539

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 540

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You will be pleased with their sincere efforts to re...

  • Page 541

    If nhtsa receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. T...

  • Page 542

    Service manuals these comprehensive service manuals provide the infor- mation that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintain- ing, servicing, and repairing fca us llc vehicles. A complete working knowledge of the vehicle, system, and/or compo...

  • Page 543

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle....

  • Page 544

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 545

    Index 10

  • Page 546

    Abs (anti-lock brake system) . . . . . . . . . . . . . . . .358 adding engine coolant (antifreeze) . . . . . . . . . . . .491 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .410 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .485 additives, fuel . . . . . . . . . ...

  • Page 547

    Anti-lock brake system (abs) . . . . . . . . . . . . . . . .358 anti-lock warning light . . . . . . . . . . . . . . . . . . . .216 appearance care . . . . . . . . . . . . . . . . . . . . . . . . .503 assistance towing. . . . . . . . . . . . . . . . . . . . . . . . .129 automatic dimming mirror . . ....

  • Page 548

    Camera, rear . . . . . . . . . . . . . . . . . . . . . . . . . . . .179 capacities, antifreeze (engine coolant) . . . . . . . . . .520 capacities, fluid . . . . . . . . . . . . . . . . . . . . . . . . . .520 caps, filler fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .410 oil (...

  • Page 549

    Seating positions . . . . . . . . . . . . . . . . . . . . . . . .84 child safety locks . . . . . . . . . . . . . . . . . . . . . . . . .34 clean air gasoline . . . . . . . . . . . . . . . . . . . . . . . .407 cleaning wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .505 climate co...

  • Page 550

    Data recorder, event . . . . . . . . . . . . . . . . . . . . . . .77 dealer service. . . . . . . . . . . . . . . . . . . . . . . . . . . .476 defroster, rear window. . . . . . . . . . . . . . . . . . . . .207 defroster, windshield . . . . . . . . . . . . . . . . . . . . . .102 delay (intermittent) w...

  • Page 551

    Emission control system maintenance . . . . . . . . . .474 engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .471 air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .480 block heater . . . . . . . . . . . . . . . . . . . . . . . . . .320 break-in recommendations . ....

  • Page 552

    Fluid level checks automatic transaxle . . . . . . . . . . . . . . . . . . . . .501 automatic transmission . . . . . . . . . . . . . . . . . .499 cooling system . . . . . . . . . . . . . . . . . . . . . . . . .489 power steering . . . . . . . . . . . . . . . . . . . . . . . . .354 fluids, lubricants...

  • Page 553

    Gauges coolant temperature . . . . . . . . . . . . . . . . . . . . .216 fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .216 odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .216 tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . .216 gear ranges . ...

  • Page 554

    Information center, vehicle . . . . . . . . . . . . . . . . . .231 inside rearview mirror . . . . . . . . . . . . . . . . . . . . .110 instrument cluster . . . . . . . . . . . . . . . . . . . . . . . .216 instrument panel and controls . . . . . . . . . . . . . . . .214 instrument panel cover . . . ....

  • Page 555

    Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .216 anti-lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .216 back-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .519 brake assist warning . . . . . . . . . . . . . . . . . . . .370 brake warning . . . . ....

  • Page 556

    Automatic door . . . . . . . . . . . . . . . . . . . . . . . . .32 child protection . . . . . . . . . . . . . . . . . . . . . . . . .34 door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 power door . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 lubrication, body . . ...

  • Page 557

    Multi-function control lever . . . . . . . . . . . . . . . . .165 new vehicle break-in period . . . . . . . . . . . . . . . . . .99 occupant restraints . . . . . . . . . . . . . . . . . . . . . . . .40 octane rating, gasoline (fuel) . . . . . . . . . . . . . . . .406 odometer. . . . . . . . . . . . ...

  • Page 558

    Phone, hands-free (uconnect®) . . . . . . . . . . . . . . .114 placard, tire and loading information . . . . . . . . . .379 power door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 outlet (auxiliary electrical o...

  • Page 559

    Security alarm . . . . . . . . . . . . . . . . . . . . . . . . . .18 remote keyless entry (rke) fcc general information . . . . . . . . . . . . . . . . . .26 remote keyless entry (sedan) . . . . . . . . . . . . . . . . .20 remote sound system (radio) controls . . . . . . . . .295 remote starting sys...

  • Page 560

    Seat belt reminder . . . . . . . . . . . . . . . . . . . . . . .43 seat belt maintenance . . . . . . . . . . . . . . . . . . . . . .509 seat belt reminder . . . . . . . . . . . . . . . . . . . . . . . . .43 seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 adjustable shoul...

  • Page 561

    Side window demisters (defrosters) . . . . . . . . . . . .310 signals, turn . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 snow chains (tire chains) . . . . . . . . . . . . . . . . . . .395 snow tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .388 spare tire. . . . . . . ...

  • Page 562

    Aging (life of tires) . . . . . . . . . . . . . . . . . . . . .393 air pressure . . . . . . . . . . . . . . . . . . . . . . . . . . .383 chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .395 changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .436 compact spare . . . ....

  • Page 563

    Minimum requirements . . . . . . . . . . . . . . . . . .421 tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .426 trailer and tongue weight . . . . . . . . . . . . . . . . .419 wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .424 trailer towing guide. . . . . ....

  • Page 564

    Playing mp3 files . . . . . . . . . . . . . . . . . . . . . . .280 uconnect® (hands-free phone) . . . . . . . . . . . . . . .114 understanding your instrument panel. . . . . . . . . . .214 uniform tire quality grades . . . . . . . . . . . . . . . . .541 universal consumer interface (uci) connector ....

  • Page 565

    Windshield washers . . . . . . . . . . . . . . . . . . . . . . .170 windshield wiper blades . . . . . . . . . . . . . . . . . . . .485 windshield wipers . . . . . . . . . . . . . . . . . . . . . . . .170 wiper blade replacement . . . . . . . . . . . . . . . . . . .485 wipers, intermittent . . . . . ...

  • Page 566

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 567

    Compass o w n e r ’ s m a n u a l 20 15 c ompas s 15mk49-126-ad fourth edition printed in u.S.A. 2 0 1 5 fca us llc.