1. DL manuals
  2. Jeep
  3. Automobile
  4. Jeep Wrangler
  5. Owner's Manual

Jeep Jeep Wrangler Owner's Manual

Manual is about: 2012

Summary of Jeep Wrangler

  • Page 1

    Wrangler owne r ’ s manual 2 0 1 0

  • Page 2: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3 understanding the featu...

  • Page 4: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 rollover warning . . . . . . . . . . . . . . . . . . . . . . . 5 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 6 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 8 䡵 vehicle ide...

  • Page 5

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle designed for both on-road and off-roa...

  • Page 6

    This owner’s manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a warranty information booklet, located on the dvd, and various customer-oriented documents. Please take the ti...

  • Page 7

    Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in an accident, rollover of the vehicle, and severe or fatal injury. Drive carefully. Failure to use the driver and passenger seat b...

  • Page 8

    1 introduction 7.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in an accident or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 10: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . 12 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . 13 䡵 steering wheel lock . . . . . . . . . . . . . . . . . . . . 1...

  • Page 11

    ▫ using the panic alarm . . . . . . . . . . . . . . . . . 21 ▫ to turn off “flash lights with lock” . . . . . . . 21 ▫ programming additional transmitters . . . . . . 22 ▫ general information . . . . . . . . . . . . . . . . . . . 22 ▫ transmitter battery replacement . . . . . . . . . . 23 䡵 remote s...

  • Page 12

    ▫ rear center lap/shoulder belt retractor lockout (four-door models only) . . . . . . . . . 44 ▫ adjustable upper shoulder belt anchorage . . . 44 ▫ seat belts in passenger seating positions . . . . . 45 ▫ automatic locking retractors (alr) mode — if equipped . . . . . . . . . . . . . . . . . . . . ...

  • Page 13

    A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number. The key code can also be obtained by your authorized dealer from your vehicle invoice. Igni...

  • Page 14

    Manual transmission — if equipped 1. Turn the ignition switch to the acc (accessory) position. 2. Push the ignition key inward. 3. Turn the ignition key to the lock position, and remove the key. Warning! Leaving unattended children in a vehicle is danger- ous for a number of reasons. A child or othe...

  • Page 15

    The engine, and remove the key. Rotate the steering wheel slightly in both directions until the lock engages. To release the steering wheel lock insert the key in the ignition, and turn the wheel slightly to the left or right, to disengage the lock. Note: if you turned the wheel to the right to enga...

  • Page 16

    If the vehicle security light turns on during normal vehicle operation (vehicle running for longer than 10 sec- onds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer. Note: the sentry key 威 immobilizer s...

  • Page 17

    Customer key programming if you have two valid sentry keys 威 , you can program new sentry keys 威 to the system by performing the following procedure: 1. Cut the additional sentry key 威 transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the ig...

  • Page 18

    Reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be reprogrammed. General information the sentry key 威 system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cau...

  • Page 19

    To set the alarm the vehicle security alarm will set when you use the remote keyless entry (rke) transmitter to lock the doors and swing gate, or when you use the power door lock switch while the door is open. After all the doors are locked and closed, the vehicle security light (located on the inst...

  • Page 20

    Illuminated entry the interior lights will come on when you open any door. The lights will remain on after all of the doors are closed, and then fade to off or they will immediately fade to off once the ignition switch is turned on. Remote keyless entry (rke) — if equipped this system allows you to ...

  • Page 21

    To unlock the doors and swing gate press and release the rke transmitter unlock button once to unlock the driver’s door only, or twice to unlock all the doors and swing gate. When the rke transmitter unlock button is pressed, the illuminated entry will initiate and the parking lights will flash twic...

  • Page 22

    1. Press the rke transmitter lock button for 4 to 10 seconds. 2. While the lock button is pressed (after four seconds), press the rke transmitter panic button. Release both buttons. The “sound horn on lock” feature can be reactivated by repeating this procedure. Using the panic alarm to turn the pan...

  • Page 23

    Note: pressing the rke transmitter lock button while you are in the vehicle will activate the vehicle security alarm. Opening a door with the vehicle security alarm activated will cause the alarm to sound. Press the rke transmitter unlock button to deactivate the ve- hicle security alarm. The “flash...

  • Page 24

    Transmitter battery replacement the recommended replacement battery is cr2032. Note: perchlorate material – special handling may apply; see www.Dtsc.Ca.Gov/hazardouswaste/ perchlorate. 1. If the rke transmitter is equipped with a screw, remove the screw. With the rke transmitter buttons facing down,...

  • Page 25

    Note: if the rke transmitter is equipped with a screw, reinstall and tighten the screw until snug. Remote starting system — if equipped this system uses the remote keyless entry (rke) transmitter to start the engine conve- niently from outside the vehicle while still maintaining security. The system...

  • Page 26

    To enter remote start press and release the remote start button on the rke transmitter twice, within five sec- onds. The parking lights will flash and the horn will chirp twice (if programmed). Then, the engine will start and the vehicle will remain in the remote start mode for a 15-minute cycle. No...

  • Page 27

    To exit remote start mode and drive the vehicle before the end of the 15-minute cycle, press and release the unlock button on the rke transmitter to unlock the doors and disarm the vehicle security alarm (if equipped). Then, prior to the end of the 15-minute cycle, insert the key into the ignition s...

  • Page 28

    Upper half door window installation — if equipped 1. Grasp the half door window and line up pins into pockets in lower door. 2. Push down to ensure the half door window is fully seated. Front door removal 1. Remove the hinge pin screws from the upper and lower outside hinges (using a #t50 torx 威 hea...

  • Page 29

    Note: if the red latch on the connector is locked, push the red latch to the right until you can only see the latch on one end (right) of the connector. This will unlock the connector tab, allowing the tab to be pressed down and enabling the harness to be disconnected. 3. Unhook the door strap from ...

  • Page 30

    2. Slide the front seat(s) fully forward. 3. Remove the trim access door from the bottom of b-pillar. 4. Unplug the wiring harness connector. Note: if the red latch on the connector is locked, push the red latch to the right until you can only see the latch on one end (right) of the connector. This ...

  • Page 31

    5. Unhook the door strap from the body hook. 6. With the door open, lift the door to clear hinge pins from their hinges, and remove door. To reinstall the door(s), perform the previous steps in the opposite order. Door locks manual door locks the front (two-door models) and rear doors (four-door mod...

  • Page 32

    Note: the ignition key that is used to start the vehicle is used to lock or unlock the doors, swing gate, and console storage. Warning! • for personal security reasons and safety in an accident, lock the vehicle doors when you drive, as well as when you park and leave the vehicle. • never leave chil...

  • Page 33

    Warning! (continued) • never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition. A child could operate power win- dows, other controls, or move...

  • Page 34

    Note: use the “automatic unlock doors on exit” feature in accordance with local laws. Automatic door locks the doors will lock automatically on vehicles with power door locks if all of the following conditions are met: 1. The “automatic door locks” feature is enabled. 2. The transmission is in gear....

  • Page 35

    Windows power windows — if equipped the power window switches are located on the instru- ment panel center stack (below the radio). The top left switch controls the left front window and the top right switch controls the right front window. The lower left switch controls the left rear passenger wind...

  • Page 36

    Console. To disable the window controls, press the win- dow lockout button downward. To enable the window controls, press the window lockout button upward. Auto-down both the driver and front passenger window switches have an “auto-down” feature. Press the window switch past the first detent, releas...

  • Page 37

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down in certain open or partially open posi- tions. This is a normal occurrence and can be minimized by adjusting ...

  • Page 38

    Caution! Do not press on rear wiper blade when closing the rear flip-up window, as damage to the blade will result. Warning! Driving with the flip-up window open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flip-up window clos...

  • Page 39

    If you will be carrying children too small for adult-sized seat belts, the seat belts or the lower anchors and tether for children (latch) feature also can be used to hold infant and child restraint systems. For more information on latch, see lower anchors and tether for children (latch). Note: the ...

  • Page 40

    Ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/shoulder belts all seating positions in your vehicle have combination lap/shoulder belts. The belt webbing retractor is de- signed to lock during very sudden s...

  • Page 41

    Warning! (continued) • two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size. Lap/shoulder belt operating ...

  • Page 42

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your bel...

  • Page 43

    Warning! (continued) • a shoulder belt placed behind will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. 4. Position the lap belt across your thighs, b...

  • Page 44

    Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • a twisted belt cannot do its job as well. In a collision,...

  • Page 45

    Rear center lap/shoulder belt retractor lockout (four-door models only) this feature is designed to lock the retractor whenever the 60% rear seatback is not fully latched. This prevents someone from wearing the rear center lap/shoulder belt when the rear seatback is not fully latched. Note: • if the...

  • Page 46

    Warning! Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. As a guide, if you are shorter than average, you ...

  • Page 47

    The vehicle seat belt” under the “child restraint” section. The chart below defines the type of feature for each seating position. Left center right first row alr second row alr alr alr third row if the passenger seating position is equipped with an alr and is being used for normal usage: only pull ...

  • Page 48

    3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode disconnect the combination lap/shoulder belt from the buckle and allow it to retract completely to dise...

  • Page 49

    Beltalert 威 will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). Beltalert 威 can be enabled or disabled by your authorized dealer or by following these steps: note: the following steps must occur within the first 60...

  • Page 50

    Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. Seat belt extender if a seat belt is too sh...

  • Page 51

    Supplemental restraint systems (srs) — airbags this vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel. The front passenger airbag is mounted in the instrument panel, above t...

  • Page 52

    The advanced front airbags have a multistage inflator design. This allows the airbag to have different rates of inflation that are based on the severity and type of collision. If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers...

  • Page 53

    Warning! • no objects should be placed over or near the airbag on the instrument panel, because any such objects could cause harm if the vehicle is in a crash severe enough to cause the airbag to inflate. • do not put anything on or around the front airbag covers or attempt to manually open them. Yo...

  • Page 54

    Improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occu- pant protection. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag: 1. Children 12 years and under should always ride buckled up in a rear seat. ...

  • Page 55

    5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the customer center. Phone numbers are provided under “if you need assistance”. Warning! • relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your...

  • Page 56

    • front and side impact sensors • driver and front passenger seat belt pretensioner airbag deployment sensors and controls occupant restraint control (orc) module the orc is part of a federally regulated safety system required for this vehicle. The orc determines if deployment of the front and/or si...

  • Page 57

    The orc also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the start or on positions. If the key is in the lock position, in the acc position, or not in the ignition, the airbags are not on and will not inflate. The orc contains a backup power supply...

  • Page 58

    Size. The bags fully inflate in about 50 to 70 millisec- onds. This is about half of the time it takes to blink your eyes. The bags then quickly deflate while helping to restrain the driver and front passenger. The driver front airbag gas is vented through the vent holes in the sides of the airbag. ...

  • Page 59

    If a deployment occurs the airbags are designed to deflate immediately after deployment. Note: front and/or side airbags will not deploy in all collisions. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following ...

  • Page 60

    Warning! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioner, and seat belt retractor assem- bly replaced by an authorized dealer as soon as possible. Enhanced accident response system in the event of an impact causing airbag...

  • Page 61

    Warning! (continued) • you need proper knee impact protection in a collision. Do not mount or locate any aftermarket equipment on or behind the knee bolsters. • it is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has an ai...

  • Page 62

    In conjunction with other data gathered during a com- plete accident investigation, the electronic data may be used by chrysler group llc and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle perfor- mance. In addition to crash i...

  • Page 63

    Data parameters that are recorded: • diagnostic trouble code(s) and warning light status for electronically-controlled safety systems, including the airbag system • vehicle speed • engine rpm • brake switch status • pedal position • and other parameters depending on vehicle configuration child restr...

  • Page 64

    Warning! In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any ...

  • Page 65

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • a rearward-facing infant restraint shou...

  • Page 66

    Retractor and then allow the belt to retract into the retractor. For additional information on alr, refer to “automatic locking mode”. • in the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path open...

  • Page 67

    With knees bent over the vehicle’s seat cushion while the child’s back is against the seatback, they should use a belt-positioning booster seat. The child and belt- positioning booster seat are held in the vehicle by the lap/shoulder belt. Children too large for booster seats children who are large ...

  • Page 68

    A hook for attachment to the tether strap anchorage, and a means for adjusting the tension of the strap. In general, you will first loosen the adjusters on the lower and tether straps so that you can more easily attach the hook or connector to the lower and tether anchorages. The tether strap should...

  • Page 69

    Latch-compatible child restraint systems are now avail- able. However, because the lower anchorages are to be introduced over a period of years, child restraint systems having attachments for those anchorages will continue to also have features for installation using the vehicle’s seat belts. Child ...

  • Page 70

    If you are installing latch-compatible child restraints in adjacent rear seating positions, you can use the latch anchors or the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position. If your child restraints are not latch- compatible, you can...

  • Page 71

    In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch anchorages (four-door models) tether strap mounting (two-door models) 70 things to know before starting your vehicle.

  • Page 72

    Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means for adjusting the tension of the strap. Forward- facing toddler restraints and some rear-facing infant restraints will also b...

  • Page 73

    Warning! Improper installation of a child restraint to the latch anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Installing child restraints using th...

  • Page 74

    2. Finally, pull on any excess webbing to tighten the lap portion around the child restraint. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. To attach a child restraint tether strap: route the tether strap over the seatback and attach the ...

  • Page 75

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Vehicles with rear web buckles that may need to be twisted • in the rear seat...

  • Page 76

    Engine break-in recommendations a long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While crui...

  • Page 77

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), whi...

  • Page 78

    Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, ...

  • Page 79

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and sidewall for cuts and cracks. Check the wheel nuts for tightness. Check the ti...

  • Page 80: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 ▫ inside day/night mirror . . . . . . . . . . . . . . . . 84 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . 85 ▫ vanity mirrors . . . . . . . . . . . . . . . . ...

  • Page 81

    ▫ manual seat height adjustment — if equipped . . . . . . . . . . . . . . . . . . . . . . 122 ▫ front seatback recline . . . . . . . . . . . . . . . . . 122 ▫ front easy entry seats — two door models . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 ▫ head restraints . . . . . . . . . . . . ...

  • Page 82

    ▫ windshield wiper operation . . . . . . . . . . . . 138 ▫ intermittent wiper system . . . . . . . . . . . . . . 139 ▫ windshield washers . . . . . . . . . . . . . . . . . . 139 ▫ mist feature . . . . . . . . . . . . . . . . . . . . . . . . 140 䡵 tilt steering column . . . . . . . . . . . . . . . . ...

  • Page 83

    ▫ freedom top™ storage bag . . . . . . . . . . . . . 159 ▫ front panel(s) installation . . . . . . . . . . . . . . 163 ▫ front panel(s) installation with rear hard top removed . . . . . . . . . . . . . . . . . . . . . . . 164 ▫ rear hard top removal . . . . . . . . . . . . . . . 164 ▫ rear hard top ...

  • Page 84

    ▫ opening the sunrider 威 . . . . . . . . . . . . . . . . 232 ▫ closing the sunrider 威 . . . . . . . . . . . . . . . . 234 䡵 folding windshield . . . . . . . . . . . . . . . . . . . . 234 ▫ lowering the windshield and removing side bars . . . . . . . . . . . . . . . . . . . . . . . . . . 236 ▫ raisin...

  • Page 85

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward...

  • Page 86

    Outside mirrors to receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than the...

  • Page 87

    Vanity mirrors vanity mirrors are located on the sun visors. To use the mirrors, rotate the sun visor down and swing the mirror cover upward. Uconnect™ phone — if equipped uconnect™ phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect™ phone al- lows you to dial a phon...

  • Page 88

    • www.Jeep.Com/uconnect • or call 1–877–855–8400 uconnect™ phone allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The uconnect™ phone is driven through your bluetooth 威 ...

  • Page 89

    Voice command button actual button location may vary with the ra- dio. The individual buttons are described in the “operation” section. The uconnect™ phone can be used with any hands-free profile certified bluetooth 威 cellular phone. See the uconnect™ website for supported phones. If your cellu- lar...

  • Page 90

    • for each feature explanation in this section, only the combined form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it. For example, you can use the combined form voice com- mand ⬙ phonebook new entry, ⬙ or you can ...

  • Page 91

    The following are general phone to uconnect™ phone pairing instructions: • press the button to begin. • after the ⬙ ready ⬙ prompt and the following beep, say ⬙ setup phone pairing. ⬙ • when prompted, after the beep, say ⬙ pair a phone ⬙ and follow the audible prompts. • you will be asked to say a f...

  • Page 92

    • the system will prompt you to say the number you want to call. • for example, you can say ⬙ 234-567-8901 ⬙ . • the uconnect™ phone will confirm the phone number and then dial. The number will appear in the display of certain radios. Call by saying a name • press the button to begin. • after the ⬙ ...

  • Page 93

    • when prompted, enter the number designation (e.G., ⬙ home, ⬙ ⬙ work, ⬙ ⬙ mobile, ⬙ or ⬙ pager ⬙ ). This will allow you to store multiple numbers for each phonebook entry, if desired. • when prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding...

  • Page 94

    • depending on the maximum number of entries down- loaded, there may be a short delay before the latest downloaded names can be used. Until then, if avail- able, the previous downloaded phonebook is available for use. • only the phonebook of the currently connected cellu- lar phone is accessible. • ...

  • Page 95

    • some phones cannot send phonebook entries if they are already connected to any system via bluetooth 威 , and you may see a message on the phone display that the bluetooth 威 link is busy. In this case, the user must first disconnect or drop the bluetooth 威 connection to the uconnect™ phone, and then...

  • Page 96

    Cellular and a home number, but you can add ”john doe’s” work number later using the ⬙ phonebook edit ⬙ feature. Delete uconnect™ phonebook entry note: editing phonebook entries is recommended when the vehicle is not in motion. • press the button to begin. • after the ⬙ ready ⬙ prompt and the follow...

  • Page 97

    • the uconnect™ phone will ask you to verify that you wish to delete all the entries from the phonebook. • after confirmation, the phonebook entries will be deleted. • note that only the phonebook in the current language is deleted. • automatic downloaded phonebook entries cannot be deleted or edite...

  • Page 98

    Answer or reject an incoming call - no call currently in progress when you receive a call on your cellular phone, the uconnect™ phone will interrupt the vehicle audio sys- tem, if on, and will ask if you would like to answer the call. Press the button to accept the call. To reject the call, press an...

  • Page 99

    Toggling between calls if two calls are in progress (one active and one on hold), press the button until you hear a single beep, indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at a time. Conference call when two calls are in progress (o...

  • Page 100

    • the uconnect™ phone will call the last number that was dialed from your cellular phone. Note: this may not be the last number dialed from the uconnect™ phone. Call continuation call continuation is the progression of a phone call on the uconnect™ phone after the vehicle ignition key has been switc...

  • Page 101

    • continue to follow the system prompts to complete the language selection. After selecting one of the languages, all prompts and voice commands will be in that language. Note: after every uconnect™ phone language change operation, only the language-specific 32-name phone- book is usable. The paired...

  • Page 102

    • the uconnect™ phone does slightly lower your chances of successfully making a phone call as to that for the cellular phone directly. Warning! Your phone must be turned on and paired to the uconnect™ phone to allow use of this vehicle feature in emergency situations, when the cellular phone has net...

  • Page 103

    Voice mail calling to learn how to access your voice mail, refer to ⬙ working with automated systems. ⬙ working with automated systems this method is used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephone system. You ca...

  • Page 104

    • some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature. Barge in - overriding prompts the “voice command” button can be used when you wish to skip part of a prompt and issue your voice command immediately. For example, if a pro...

  • Page 105

    Phone, the audio will be played through your vehicle’s audio system. The uconnect™ phone will work the same as if you dial the number using voice command. Note: certain brands of cellular phones do not send the dial ring to the uconnect™ phone to play it on the vehicle audio system, so you will not ...

  • Page 106

    If you would like to connect or disconnect the bluetooth 威 connection between a uconnect™ phone paired cellular phone and the uconnect™ phone, follow the instructions described in your cellular phone user’s manual. List paired cellular phone names • press the button to begin. • after the “ready” pro...

  • Page 107

    • after the ⬙ ready ⬙ prompt and the following beep, say ⬙ setup phone pairing. ⬙ • at the next prompt, say ⬙ delete ⬙ and follow the prompts. • you can also press the button at any time while the list is being played, and then choose the phone you wish to delete. Things you should know about your u...

  • Page 108

    This procedure may be repeated with a new user. The system will adapt to the last trained voice only. To restore the voice command system to factory default settings, enter the voice training session via the above procedure and follow the prompts. Voice command • for best performance, adjust the rea...

  • Page 109

    • storing names in the phonebook when the vehicle is not in motion is recommended. • it is not recommended to store similar sounding names in the uconnect™ phonebook. • phonebook (downloaded and uconnect™ phone lo- cal) name recognition rate is optimized when the entries are not similar. • numbers m...

  • Page 110

    • echo at the phone far end can sometimes be reduced by lowering the in-vehicle audio volume. • in a convertible vehicle, system performance may be compromised with the convertible top down. Bluetooth 威 communication link cellular phones have been found to lose connection to the uconnect™ phone. Whe...

  • Page 111

    110 understanding the features of your vehicle.

  • Page 112

    3 understanding the features of your vehicle 111.

  • Page 113

    112 understanding the features of your vehicle.

  • Page 114

    Voice commands primary alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all voice commands primary alternate(s) call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help home 3 understa...

  • Page 115

    Voice commands primary alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous record again voice commands primary alternate(s) redial return to main menu return or main menu select phone select send set up...

  • Page 116

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 117

    Note: if you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the voice command button, listen for the beep, and say your command. Pressing the voice command button while the system i...

  • Page 118

    Commands the voice command system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the volume 1. Start a dialogue by pressing the voice command button. 2. Say a command (e.G., “help”). 3. Us...

  • Page 119

    Radio fm to switch to the fm band, say “fm” or “radio fm”. In this mode, you may say the following commands: • “frequency” (to change the frequency) • “next station” (to select the next station) • “previous station” (to select the previous station) • “radio menu” (to switch to the radio menu) • “mai...

  • Page 120

    Memo to switch to the voice recorder mode, say “memo”. In this mode, you may say the following commands: • “new memo” (to record a new memo) — during the recording, you may press the voice command button to stop recording. You proceed by saying one of the following commands: − “save” (to save the me...

  • Page 121

    Note: keep in mind that you have to press the voice command button first and wait for the beep before speaking the “barge in” commands. Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect™ voice “voice training” feature may be u...

  • Page 122

    Warning! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Only adjust a seat while the vehicle is parked. Manual seat adjustment 3 understanding the featu...

  • Page 123

    Manual seat height adjustment — if equipped the driver’s seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat. Pull upward on the handle to raise the seat; push downward on the handle to lower the seat. Front seatback recline lean forward befo...

  • Page 124

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seatbelt and be seriously or fatally injured. Use the recliner only when the vehicle is parked. Front easy entry seats — two door models push th...

  • Page 125

    1. To return the seat to a sitting position, rotate the seatback upright until it locks. 2. Push the seat rearward until the track locks. Note: • if equipped with combination lever the seatback will return to its first locked position. The recliner handle will have to be actuated to adjust the seatb...

  • Page 126

    To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the large button, located on the base of the head restraint, and push downward on the head restraint. Note: the rear head restraints are not adjustable. To remove the head restraint, pull upward on the...

  • Page 127

    To install the head restraint, insert the head restraint rods into each guide, apply pressure down on the headrest until the head restraint reaches the first lock position, push the large button in and push down and adjust head restraint to desired position. Note: ensure that the front of the head r...

  • Page 128

    2. Slowly flip the entire seat forward. 3. Return the seat to the normal position. 4. Raise the rear seatback using the assist strap and firmly lock the seat into position. Rear seat release folding rear seat 3 understanding the features of your vehicle 127.

  • Page 129

    Removing the rear seat — two door models warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • do not allow people to ride in any area of your vehicle that is n...

  • Page 130

    4. Press down on the release bar on each side, and pull the seat out and away from the lower bracket. 5. Remove the seat from the vehicle. Replacing the rear seat — two door models reverse the steps for removing the seat. Warning! • to help protect against personal injury, passengers should not be s...

  • Page 131

    Note: • prior to folding the rear seat, it may be necessary to reposition the front seat to its mid-track position. • be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily. Warning! • it is extremely dangerous to ride in a cargo area...

  • Page 132

    To raise the rear seat raise the seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. Note: if the rear seatback is not fully latched, the center shoulder belt will not be ab...

  • Page 133

    To close the hood, remove the support rod from the hood panel and place it in the retaining clip. Lower the hood slowly. Secure both of the hood latches. Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in mot...

  • Page 134

    Headlights and parking lights turn the end of the multifunction lever to the first detent for parking lights and instrument panel lights. Turn to the second detent for headlight operation. Note: • lens fogging can occur under certain atmospheric conditions. This will usually clear as atmospheric con...

  • Page 135

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: • if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside...

  • Page 136

    Lights-on reminder if the headlights or parking lights are on after the ignition is turned off, a chime will sound when the driver’s door is opened. High/low beam switch push the multifunction lever away from you to switch the headlights to high beam. Pull the lever toward you to switch the headligh...

  • Page 137

    Rotate the center portion of the lever upward to the last detent to turn on the interior lighting. Daytime running lights — if equipped the headlights come on at a low intensity level after the vehicle has been driven approximately 3 ft (1 m). They will turn off when the vehicle is turned off or whe...

  • Page 138

    Cargo lamp the courtesy and dome lights will turn on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the upward detent position, or if equipped, when the un- lock button is pressed on the remote keyless entry (rke) transmitter. ...

  • Page 139

    Windshield wipers and washers the windshield wiper/washer control lever is located on the right side of the steering column. The front wipers are operated by rotating a switch, located at the end of the lever. For information on using the rear window wiper/ washer, refer to “rear window features” in...

  • Page 140

    Caution! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted. Intermittent wiper ...

  • Page 141

    If the lever is pulled while in the off position, the wipers will operate for two or three wipe cycles and then turn off. Warning! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield ...

  • Page 142

    Tilt steering column this feature allows you to tilt the steering column upward or downward. The tilt lever is located on the steering column, below the turn signal lever. Push down on the lever to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or...

  • Page 143

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this war...

  • Page 144

    Simultaneously. If this occurs, the electronic speed con- trol system can be reactivated by pushing the electronic speed control on/off button and resetting the desired vehicle set speed. To activate push the on/off button. The cruise indicator light in the instrument cluster will illuminate. To tur...

  • Page 145

    To deactivate a soft tap on the brake pedal, pulling the electronic speed control lever toward you, or normal brake or clutch pressure while slowing the vehicle will deactivate electronic speed control without erasing the set speed memory. Pressing the on/off button or turning the ignition switch of...

  • Page 146

    Vehicles equipped with manual transmissions may need to be shifted into a lower gear to climb hills without speed loss. Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose contro...

  • Page 147

    Electrical power outlet there are two 12 volt (13 amp) auxiliary power outlets that can provide power for accessories designed for use with the standard power outlet adapters. The power outlet, located in the lower portion of the instrument panel, has a snap-on plastic cap so that it can be covered ...

  • Page 148

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 149

    Caution! (continued) • power outlets are designed for accessory plugs only. Do not hang any type of accessory or acces- sory bracket from the plug. Cupholders front cupholders the front cupholders are located in the center console. Note: the front cupholder insert is removable for cleaning. Front cu...

  • Page 150

    Rear cupholders the rear cupholders are located on the back of the center console. Storage console storage compartment to lock or unlock the storage compartment, insert the ignition key and turn. To open the storage compartment, press the latch and lift the cover. Rear cupholders center console 3 un...

  • Page 151

    Rear storage compartment the rear storage compartment cover is held by a spring- loaded latch. In order to remove the rear storage com- partment cover, use the following procedure: note: the rear storage compartment latch should not be used as cargo tie-down. 1. Flip up the pull loop so it is perpen...

  • Page 152

    Hard top are to be used independently. Removal is mandatory to prevent any possible wear and tear on the soft top. Your vehicle warranty will not cover damage resulting from both tops remaining on the vehicle at the same time for extended periods of time. Removing the soft top 1. Locate and remove t...

  • Page 153

    4. Using a rubber mallet, carefully tap the knuckles from the left and right metal pivot brackets. Remove the soft top from the vehicle and store in a clean, dry location. 5. Unzip the zipper on the sport bar cover to expose the pivot brackets. Remove the brackets using a #t30 torx 威 head driver. Re...

  • Page 154

    Installing the soft top note: the following procedures are for first time set up only. For future soft top procedures, refer to “soft top” in this section. 1. Locate and remove the following items prior to hard top removal: • right and left door frames • door frame attachment knobs (four for two-doo...

  • Page 155

    A. If the pivot brackets have been removed, unzip the sport bar covers and attach the pivot brackets to the sports bar with the four screws that were removed using a #t30 torx 威 head driver. Re-cover and re-zip the sport bar covers. B. Lay the soft top into the rear of the vehicle with the bows poin...

  • Page 156

    D. Screw the pivot screws back into place using a #t30 torx 威 head driver. Secure them until they are snug, being careful not to cross-thread the screws or over- tighten. Caution! Do not overtighten the screws. You can strip the screws if they are overtightened. 5. Remove the swing gate bar (black m...

  • Page 157

    Freedom top™ three-piece modular hard top — if equipped caution! • the hard top is not designed to carry any addi- tional loads such as roof racks, spare tires, build- ing, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle, and thus ca...

  • Page 158

    Front panel(s) removal note: left panel must be removed before removing right panel. 1. Fold down the sun visor, and move it to the side. 2. Turn the rear fasteners (knobs) (located on the over- head speaker bar assembly) counterclockwise until they can be removed. 3 understanding the features of yo...

  • Page 159

    3. Turn the center l-shaped locks (two) from the center of the roof panel. 4. Turn the rear l-shaped lock (located above the shoul- der belt anchorage). 158 understanding the features of your vehicle.

  • Page 160

    5. Unlatch the header panel latch located at the top of the windshield. 6. Remove the left-hand panel. To remove the right panel, follow the steps above except for step 3. Freedom top™ storage bag your vehicle comes with a freedom top™ storage bag that allows you to store your freedom top™ panels. T...

  • Page 161

    Insert the right side freedom panel into the bag with the latches facing downward. Unfold the black panel divider (ensure the divider is laying flat). Secure the velcro, located at the center of the divider. 160 understanding the features of your vehicle.

  • Page 162

    Insert the left-side freedom panel into the bag with the latches facing upward. Note: ensure the front freedom panel latch is closed prior to inserting the panel into the bag. Unfold the outer flap and zip the freedom bag closed. 3 understanding the features of your vehicle 161.

  • Page 163

    Install the seat attachment strap (at the top of the bag) through the loops. Lift the freedom bag into the vehicle with the hooks and straps facing the back of the rear seat. Attach the clips at the bottom of the bag to the child restraint anchorages, located at the base of the rear seat. 162 unders...

  • Page 164

    Wrap the upper strap around the rear head restraints and loop the strap through the buckle. Pull on the strap to tighten the freedom bag securely against the rear seat. Front panel(s) installation note: set the panels on the windshield frame so that there is no overhang. Also, make sure that the pan...

  • Page 165

    Front panel(s) installation with rear hard top removed 1. Turn the left and right panels over and move the spacer block (located on the rear of the panel) upward 90 degrees. Note: the front panel(s) must be positioned properly to ensure sealing. Set the panels on the windshield frame so that there i...

  • Page 166

    4. Remove the six torx 威 head screws that secure the hard top to the vehicle (along the interior bodyside) using a #40 torx 威 head driver. 5. Open the swing gate all the way to ensure clearance of the rear window glass. Lift the rear window glass. 6. Locate the wire harness on the left rear inside c...

  • Page 167

    7. Release the red locking tab by pushing upward. 8. To remove the wiring harness press the side tab and pull to disconnect. Note: if necessary, pliers can be used to lightly squeeze grips while disconnecting the washer hose. 166 understanding the features of your vehicle.

  • Page 168

    9. To remove the washer hose, pinch the grips on hose connector and pull. 10. Close the swing gate. 11. Remove the hard top from the vehicle. Place the hard top on a soft surface to prevent damage. Rear hard top installation note: if the door frames are installed from soft top usage, they must be re...

  • Page 169

    Door frame warning! Do not drive your vehicle on pavement with the door frame(s) removed as you will lose the protection that they can provide. This procedure is furnished for use during off-road operation only. Caution! Failure to follow these cautions may cause interior water damage, stains or mil...

  • Page 170

    Warning! Use both hands to remove the door frames. The door frames will fold and could cause injury if both hands are not used. 2. Place one hand on the upper rear and one hand on the front of the door frame. 3. Pull the frame toward you with your rearward hand to remove the frame from the vehicle. ...

  • Page 171

    Warning! Never store the door frames in your vehicle. In an event of an accident, a loose door frame many cause personal injury. If removed, always store the door frames outside of the vehicle. Door frame installation — two-door models 1. Unfold door frame and unscrew thumbscrews. 2. Set the door fr...

  • Page 172

    3. After the door frame pin has been set into the body side hole, carefully set the front of the door frame into the rubber seal at the top of the windshield. 4. Starting with the front of the door frame, clip it over the metal side bar and then clip the rear, making sure that the material for the s...

  • Page 173

    Door frame removal — four-door models 1. Unscrew and remove the two forward most door frame attachment knobs. Warning! Use both hands to remove the door frames. The door frames will fold and could cause injury if both hands are not used. 2. Place one hand on the upper rear and one hand on the upper ...

  • Page 174

    3. Pull the frame toward you with your front hand to remove the frame from the vehicle. 4. Unscrew and remove the remaining door frame at- tachment knob on the rear door frame. 5. Place one hand on the upper rear and one hand on the upper front of the rear door frame. Pull the frame toward you with ...

  • Page 175

    6. Screw the knob back into the door frame and fold for storage. Store in a secure location. Warning! Never store the door frames in your vehicle. In an event of an accident, a loose door frame many cause personal injury. If removed, always store the door frames outside of the vehicle. Door frame in...

  • Page 176

    3. Position the top of the door frame against the metal sport bar and press onto the side bar making sure not to pinch the material of the sports bar covers and to ensure it is properly positioned on the seal above the front of the rear door. 4. Loosely install the rear knob (long knob) to hold the ...

  • Page 177

    5. Carefully set the front of the front door frame in the rubber seal at the top of the windshield. Then, clip the front of the door rail over the side bar making sure that the material for the side bar cover is not pinched by the door frame. Position the rear of the front door frame to lay on top o...

  • Page 178

    Soft top — two door models please visit the owners section of jeep.Com for instruc- tional videos. Caution! The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunt- ing, or camping supplies, and/or luggage, etc. Also, it was not designed as a struct...

  • Page 179

    Caution! (continued) • refer to “appearance care for fabric top models” in “maintaining your vehicle” for further infor- mation. It contains important information on cleaning and caring for your vehicle’s fabric top. • do not use any tools (screwdrivers, etc.) to pry or force any of the clamps, clip...

  • Page 180

    Caution! (continued) • careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle’s interior. • the soft top must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior. Quick steps to loweri...

  • Page 181

    2. Release header latches from the windshield frame. 3. Release the sunrider 威 latch (both sides). 180 understanding the features of your vehicle.

  • Page 182

    4. Open the swing gate and lower the top. Note: ensure fabric does not overhang the sides of the vehicle. Quick steps to raising the soft top refer to “raising the soft top” in this section for further information. 1. Open the swing gate and raise the top, engaging the sunrider 威 latches (another pe...

  • Page 183

    2. Engage header latches. 182 understanding the features of your vehicle.

  • Page 184

    3. Install rear corner panels. 4. Install side and back windows. 3 understanding the features of your vehicle 183.

  • Page 185

    Lowering the soft top 1 — header bow 6 — quarter window 2 — 2–bow 7 — check strap 3 — 3–bow 8 — front retainer — quarter window 4 — sail panel 9 — bottom retainer — quarter window 5 — body side retainer 184 understanding the features of your vehicle.

  • Page 186

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 3 understanding the features of your vehicle 185.

  • Page 187

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 188

    5. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets. • unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across th...

  • Page 189

    6. Undo the velcro 威 that runs along the top and rear edge of the side window. 7. Beginning from the rear lower corner, completely unzip the window. 8. Once unzipped, remove the side window retainers from the door channel and body side channel. Repeat this step on the opposite side. 9. Finish releas...

  • Page 190

    10. As you begin to lower the top, fold the sail panels so that they rest on top of the soft top. 11. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket ba...

  • Page 191

    12. Completely release the latches from the loops on the windshield frame. If your vehicle is not equipped with the sunrider 威 package, proceed to step 15. 13. Make sure the plastic sleeves are slid rearward over the sunrider 威 link (sunrider 威 models only). 190 understanding the features of your ve...

  • Page 192

    14. Unlatch the side bows from both door rails (sun- rider 威 models only). 15. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake light. Move to the front of the vehicle. Grasp the side bow behind the header and lift the top, folding it towa...

  • Page 193

    16. Tuck the fabric and the check straps between the bows and as far inward as possible. This will keep any portion of the top from flapping outside of the vehicle. 17. Close the front header latches. 18. Remove the door frames, if desired. Refer to “door frame” in this section for further informati...

  • Page 194

    4. Standing on the side of the vehicle, lift the top by the side bow and the 2–bow (middle bow) up and over the sports bar until the header rests on the top of the windshield frame. 5. Make sure the sunrider 威 bracket on the side bows latches to the door rails (sunrider 威 models only). 3 understandi...

  • Page 195

    6. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 7. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel u...

  • Page 196

    8. Move to the rear of the vehicle and gently pull the sail panels over the rear roof bow. 9. Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (3–bow) will aid to reac...

  • Page 197

    10. To install the side windows, affix the window tem- porarily by attaching to the velcro 威 in the rear corner. Start the zipper but close only about 1 in (2.5 cm). 11. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on...

  • Page 198

    12. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro 威 along the top and rear of the window. Repeat this step for the opposite side. 1 ...

  • Page 199

    13. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. 198 understanding the features of your vehicle.

  • Page 200

    14. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage. 15. Run the zipper fully around to the right side of the window. 3 understanding the features of yo...

  • Page 201

    16. Grasp the swing gate bar and position it into the swing gate brackets. 17. Apply downward pressure on the top corner of the rear soft top bow (3–bow), then complete attaching the sail panel retainers into the body side channel. 18. Close the header latches and return the sun visors to their secu...

  • Page 202

    Soft top (four-door models) please visit the owner’s section of jeep.Com for instruc- tional videos. Caution! The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunt- ing, or camping supplies, and/or luggage, etc. Also, it was not designed as a stru...

  • Page 203

    Caution! (continued) • do not lower the top with the windows installed. Window and top damage may occur. • refer to “appearance care for fabric top models” in “maintaining your vehicle” for further infor- mation. It contains important information on cleaning and caring for your vehicle’s fabric top....

  • Page 204

    Caution! Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • it is recommended that the top be free of water prior to opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle...

  • Page 205

    Quick steps for lowering the soft top 1. Remove the side and back windows. 2. Release header latches from the windshield frame. 204 understanding the features of your vehicle.

  • Page 206

    3. Fold header rearward, pulling the fabric to the rear. 3 understanding the features of your vehicle 205.

  • Page 207

    4. Release sunrider 威 latch (both sides). 5. Open the swing gate and lower the top. Note: ensure the fabric does not overhang the sides of the vehicle. 206 understanding the features of your vehicle.

  • Page 208

    Quick steps for raising the soft top 1. Open the swing gate and raise the top, engaging the sunrider 威 latches (another person may be needed to help with this operation). 3 understanding the features of your vehicle 207.

  • Page 209

    2. Install rear corner panels. 3. Rotate the header forward. 208 understanding the features of your vehicle.

  • Page 210

    4. Engage the header latches. 5. Install the side and back windows. 3 understanding the features of your vehicle 209.

  • Page 211

    Folding down the soft top 1 — header bow 6 — body side retainer 2 — 2–bow 7 — quarter window 3 — 3–bow 8 — check strap 4 — 4–bow 9 — front retainer — quarter window 5 — sail panel 10 — bottom retainer — quarter window 210 understanding the features of your vehicle.

  • Page 212

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 3 understanding the features of your vehicle 211.

  • Page 213

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 214

    4. Open the swing gate. 5. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets. • unzip the rear window starting at the right lower corner of the window. Pull ...

  • Page 215

    6. Undo the velcro 威 that runs along the top and rear edge of the side window. 7. Beginning from the rear lower corner, completely unzip the window. 8. Once unzipped, remove the side window retainers from the door channel and body side channel. Repeat this step on the opposite side. 9. Finish releas...

  • Page 216

    10. Fold the sail panels so that they rest on top of the soft top. 11. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to dis...

  • Page 217

    12. Grasp the front side bow behind the header, and lift the top. 13. Fold back the front section of the top, pulling the fabric rearward. Gently rest the header on top of the rear portion of the deck. 216 understanding the features of your vehicle.

  • Page 218

    14. Fold the top so that the material forms a ⬙ w ⬙ as shown. Enter the vehicle and move the material into two folds. 15. Release the side bows by pressing down on the latch above the front of the rear door. Push the top rearward to disengage. Repeat this step on the other side. 3 understanding the ...

  • Page 219

    16. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake light. Grasp the folded side bows and slide the top along the door frame track to the rear door frame. 17. Gently slide the side bows off the door frame track and lower the top down into...

  • Page 220

    19. Once the top is fully down, use the velcro 威 straps provided to secure the top to the vehicle by wrapping the strap around the side bows and through the slot on the body. 20. Close the front header latches. 21. Remove the door frames, if desired. Refer to “door frame” in this section for further...

  • Page 221

    4. Grasp the folded side bows and lift to the top of the rear door frames. Note: help from another person will ease this opera- tion. 5. Insert the slider feature of the knuckles into the door frame tracks and slide the top forward. 220 understanding the features of your vehicle.

  • Page 222

    6. Ensure that the top locks into the sunrider 威 locking mechanisms that are located above the front of the rear doors. 7. Unclip and move the sun visors to the side. 8. Standing on the side of the vehicle, lift the top by the side bow until it rests on the windshield frame. 3 understanding the feat...

  • Page 223

    9. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 10. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel ...

  • Page 224

    11. Ensure that the straps are positioned correctly before pulling the sail panels over the rear roof bow (4–bow). Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (4–...

  • Page 225

    12. To install the side windows, affix the window tem- porarily by attaching it to the velcro 威 in the upper rear corner. Start the zipper but close only about 1 in (2.5 cm). 13. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly posi...

  • Page 226

    14. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro 威 along the top and rear of the window. Repeat this step for the opposite side. 1 ...

  • Page 227

    15. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. 226 understanding the features of your vehicle.

  • Page 228

    16. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage. 17. Run the first zipper fully around to the right side of the window. 18. Grasp the swing gate bar...

  • Page 229

    20. Close the header latches and return the sun visors to their secured position. Sunrider 姞 (two-door models) — if equipped caution! Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior. Note: if you are going to be driving ...

  • Page 230

    Opening the sunrider 姞 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Slide the plastic sleeve forward. 3 understanding the features of your vehicle 229.

  • Page 231

    4. Grasp the header and lift the top back. Make sure the material is folded back as shown. Note: the sunrider 威 latch on the door rail should not be activated for sunrider 威 use. If activated, the soft top must be reinstalled starting from the sail panels. 5. Locate the straps to secure the side bow...

  • Page 232

    Closing the sunrider 姞 1. Remove the straps from the side bows. 2. Unclip and move the sun visors to the side. 3. Grasp the front header and pull it to the front of the vehicle. 4. Hook the header latches to the loops on the wind- shield frame, close latches, and return the sun visors to their origi...

  • Page 233

    Opening the sunrider 姞 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Grasp the front side bow behind the header, and lift the top. 232 understanding the features of your vehicle.

  • Page 234

    4. Fold back the front section of the top and gently rest the header on top of the rear portion of the deck. 5. Fold the top so that the material forms a ⬙ w ⬙ as shown. Enter the vehicle and move the material into two folds. 3 understanding the features of your vehicle 233.

  • Page 235

    6. Secure the top by using the two provided straps. Each strap will wrap around the side bow and velcro 威 to itself; use one strap on each side of the vehicle. Closing the sunrider 姞 perform the above steps in the opposite order. Note: failure to fold the fabric rearward will allow the material to s...

  • Page 236

    Raise the windshield and reinstall the side bars as soon as the task that required their removal is completed and before you return to on-road driving. Both you and your passenger should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down...

  • Page 237

    Lowering the windshield and removing side bars 1. Lower the fabric top or remove the hard top following the instructions in this manual. Note: to assist in properly reinstalling side bars, mark the original locations prior to removing. 2. Remove the two top hex bolts (13 mm), and the one side hex bo...

  • Page 238

    7. Remove the one hex bolt (13 mm) visible through the plastic trim on the bottom side of the side bar, one hex bolt (13 mm) on the side of the side bar, and one hex bolt (13 mm) on top of the side bar. Note: pull side bar out horizontally when removing. Caution! Do not remove the head impact foam f...

  • Page 239

    Warning! You or others could be injured if you carry the side bars loose in your vehicle. Remove the side bars from the vehicle or securely store them as described or they may cause personal injury if an accident occurs. See your authorized dealer for the cinch straps. 10. Remove the windshield wipe...

  • Page 240

    12. Lower the windshield gently until it contacts the rubber hood bumpers. 13. Secure the windshield by passing a cinch strap through the footman hoop on the center of the hood and on the center of the windshield frame. Tighten the strap to secure the windshield in place. Raising the windshield and ...

  • Page 241

    3. Attach the front of the side bar to the windshield frame. • install the top two hex bolts (13 mm) first, then the lower side hex bolt (13 mm). The lower side bolt will not align until the top two bolts are installed. 4. Tighten all side bar attachment bolts. 5. Install the lower windshield plates...

  • Page 242

    Rear window features — hard top only rear window wiper/washer — if equipped a rotary ring switch on the control lever (located on the right side of the steering column) controls the operation of the rear wiper/washer function. Rotate the switch upward to the “on” position will activate the rear wipe...

  • Page 243

    Rear window defroster — if equipped the rear window defroster button is located on the bottom right-side of the blower control knob. Press this button to turn on the rear window defroster. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster auto...

  • Page 244: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 246 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . 247 䡵 instrument cluster descriptions . . . . . . . . . . . 248 䡵 compass and trip computer — if equipped . . 263 ▫ control buttons ...

  • Page 245

    䡵 media center 730n/430 (rer/ren/rbz) — am/fm stereo radio and cd/dvd/hdd/ nav — if equipped . . . . . . . . . . . . . . . . . . . . 284 ▫ operating instructions — voice command system — if equipped . . . . . . . . . . . . . . . . . 285 ▫ operating instructions — uconnect™ phone — if equipped . . . ...

  • Page 246

    ▫ electronic serial number/sirius identification number (esn/sid) . . . . . . . . . 310 ▫ selecting uconnect™ multimedia (satellite) mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311 ▫ satellite antenna . . . . . . . . . . . . . . . . . . . . . 311 ▫ reception quality . . . . . . . ...

  • Page 247

    Instrument panel features 1 — air outlet 6 — climate controls 2 — instrument cluster 7 — power outlet 3 — horn 8 — lower switch bank 4 — radio 9 — auxiliary power outlet / cigar lighter 5 — glove compartment 246 understanding your instrument panel.

  • Page 248

    Instrument cluster 4 understanding your instrument panel 247.

  • Page 249

    Instrument cluster descriptions 1. Fuel gauge the pointer shows the level of fuel in the fuel tank. Note: when the ignition switch is turned to off, the fuel gauge, voltmeter, oil pressure and temperature gauges may not show accurate readings. When the engine is not running, turn the ignition switch...

  • Page 250

    6. Front axle lock indicator — if equipped indicates when the front axle lock has been activated. 7. Seat belt reminder light a warning chime and an indicator light will alert you to buckle the seat belts. When the belt is buckled, the chime will stop, but the light will stay on for about six second...

  • Page 251

    Headlights or park lights are left on, the high beam indicator light will remain illuminated and a chime will sound. 11. Brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the p...

  • Page 252

    Warning! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. Vehicles equipped with the anti-lock brake system (abs), are also equipped with el...

  • Page 253

    13. Airbag warning light this indicator lights and remains lit for six to eight seconds when the ignition is first turned on. If the light does not come on for six to eight seconds, stays on or comes on while driving, have the airbag system checked by an authorized dealer. Refer to “occupant restrai...

  • Page 254

    18. Temperature gauge the temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or ...

  • Page 255

    21. Odometer / trip odometer / eco (fuel saver indicator) button press this button to change the display from odometer to either of the two trip odometer settings or the “eco” display. Trip a or trip b will appear when in the trip odometer mode. Press and hold the button for two seconds to reset the...

  • Page 256

    Please note that the tpms is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the tpms low tire pressure telltale. Your vehicle has also been equipped wi...

  • Page 257

    24. Odometer / trip odometer display area the odometer shows the total distance the vehicle has been driven. The trip odometer shows individual trip mileage. Refer to “odometer / trip odometer / eco (fuel saver indicator) button” for additional information. U.S. Federal regulations require that upon...

  • Page 258

    The eco display will toggle between eco and eco-on depending on driving habits and vehicle usage. Press the odometer / trip odometer / eco (fuel saver indicator) button to change the display from odometer to either of the two trip odometer settings or the “eco” display. Low tire when the appropriate...

  • Page 259

    Gascap if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “gascap” message will display in the odometer display area. Tighten the fuel filler cap properly and press the trip odometer button to turn off the message. If the problem contin...

  • Page 260

    3. Turn the ignition switch to the off/lock position. Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary repeat this procedure. 25. Malfunction indicator light (mil) the malfunction indicator light (mil) is a part of an ...

  • Page 261

    Warning! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants or wood or cardboard, etc. This could result in death or serious injur...

  • Page 262

    27. O/d (overdrive) off indicator light this light will illuminate when the o/d off button has been selected and overdrive has been turned off. The o/d off button is located on the center console. 28. Sway bar indicator light — if equipped this indicator will illuminate when the front sway bar is di...

  • Page 263

    30. Electronic throttle control (etc) light this light informs you of a problem with the electronic throttle control (etc) system. If a problem is detected while the engine is run- ning, the light will either stay on or flash depending on the nature of the problem. Cycle the ignition key when the ve...

  • Page 264

    Compass and trip computer — if equipped the compass/trip computer is located in the instru- ment cluster. It features a driver-interactive display (dis- plays information such as outside temperature, compass direction, and trip information). Control buttons note: the system will display the last kno...

  • Page 265

    The following trip displays can be reset or changed: • avg eco (changes to present fuel economy) • et (will reset display) trip conditions average fuel economy (avg eco) this display shows the average fuel economy. Estimated range (dte) this display shows the estimated distance that can be traveled ...

  • Page 266

    The eco display will toggle between eco and eco-on depending on driving habits and vehicle usage. Compass/temperature display note: if the vehicle is equipped with a chrysler uconnect™ gps (navigation radio), the nav system will provide the compass direction, and the variance and calibration menus w...

  • Page 267

    • magnetic and battery powered devices, (such as cell phones, ipod’s, radar detectors, pda’s and laptops) should be kept away from the top of the instrument panel. This is where the compass module is located and such devices may interfere and cause false com- pass readings. Automatic compass calibra...

  • Page 268

    3. Manual compass calibration has been initiated. Drive the vehicle slowly in one or more circles under 5 mph (8 km/h) in an area free from large metal objects until the cal symbol is extinguished. When the cal symbol is no longer displayed, the compass is calibrated and should display correct head-...

  • Page 269

    Note: the u.S./metric display will change from en- glish to metric or metric to english before the var symbol appears, however, it will revert back to its original setting after programming the compass func- tions. Outside temperature if the outside temperature is more than 131°f (55°c), the display...

  • Page 270

    Media center 230 (req) — am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) note: the radio sales code is located on the lower right side of the radio faceplate. Operating instructions - radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power s...

  • Page 271

    To seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Scan button pressing the scan button causes the tuner to search for the next listenable stat...

  • Page 272

    3. After adjusting the hours, press the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll control knob to save the time change. 5. To exit, press any button/knob or wai...

  • Page 273

    Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the right or left to increase or decrease the treble tones. Push the rotary tune/scroll control knob a fourth time and balance will display. Turn the tune/ scroll control knob to the r...

  • Page 274

    Program type 16-digit character display classic rock cls rock college college country country foreign language language information inform jazz jazz news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk r...

  • Page 275

    Setup button pressing the setup button allows you to select between the following items: note: turn the tune/scroll control knob to scroll through the entries. Push the audio/select button to select an entry and make changes. • dvd enter - when the disc is in dvd menu mode, selecting dvd enter will ...

  • Page 276

    • ves™ lock - locks out rear ves™ remote controls (if equipped). • ves™ ch1/ch2 - allows the user to change the mode of either the ir1 or ir2 wireless headphones by pressing the audio/select button (if equipped). • set home clock - pressing the select button allows you to set the clock. Turn the tun...

  • Page 277

    The tune/scroll control knob to scroll up and down to select the number and then push to select. Subtitles — if equipped selecting this item allows you to choose between subtitle off or on. Audio drc — if equipped selecting this item allows you to limit maximum audio dynamic range. The default is se...

  • Page 278

    You may add a second station to each pushbutton by repeating the above procedure with this exception: press the set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am, 12 fm, and 12 satellite (if equipped...

  • Page 279

    Note: the ignition switch must be in the on or acc position to operate the radio. Load button — loading compact disc(s) press the load button and the pushbutton with the corresponding number (1-6) where the cd is being loaded. The radio will display please wait and prompt when to insert disc. After ...

  • Page 280

    Scan button (cd mode) press the scan button to scan through each track on the cd currently playing. Time button (cd mode) press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff (cd mode) press and hold ff (fast forward) and the cd playe...

  • Page 281

    The radio uses the following limits for file systems: • maximum number of directory levels: 8 • maximum number of files: 255 • maximum number of folders: 100 • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙ . ⬙ and a three- character extension) • level 2: 3...

  • Page 282

    Mpeg specification sampling frequency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48 wma specification sampling frequency (khz) bit rate (kbps) wma 44.1 and 48 48,...

  • Page 283

    List button (disc mode for mp3/wma play) pressing the list button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the tune/scroll control knob. Selecting a folder by pressing the tune/scroll control knob will begin playing the files contained in that...

  • Page 284

    Scan button (auxiliary mode) no function. Eject button (auxiliary mode) no function. Time button (auxiliary mode) press the time button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. Rw/ff (auxiliary mode) no function. Set button (auxil...

  • Page 285

    Operating instructions - video entertainment system (ves)™ (if equipped) refer to separate “video entertainment system (ves)™ guide.” dolby 威 manufactured under license from dolby 威 laboratories. ⬙ dolby 威⬙ and the double-d symbol are trademarks of dolby 威 laboratories. Macrovision this product inco...

  • Page 286

    Operating instructions — voice command system — if equipped for the radio, refer to “voice command” in “understand- ing the features of your vehicle”. Operating instructions — uconnect™ phone — if equipped refer to “uconnect™ phone” in “understanding the features of your vehicle”. Clock setting proc...

  • Page 287

    2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “daylight savings.” touch the screen where the words “daylight savings” are dis- played to change the current setting. ...

  • Page 288

    Satellite clock is greenwich mean time (gmt). This is the worldwide standard for time. This makes the system’s clock very accurate once the appropriate time zone and daylight savings information is set. To manually set the clock — rer/ren 1. Turn on the radio. 2. Touch the screen where the time is d...

  • Page 289

    Show time if radio is off when selected, this feature will display the time of day on the touch screen when the radio is turned off. Proceed as follows to change the current setting: 1. Turn on the radio. 2. Touch the screen where the time is displayed. 3. Touch the screen where “user clock” is disp...

  • Page 290

    Media center 130 (res) — am/fm stereo radio with cd player (mp3 aux jack) note: the radio sales code is located on the lower right side of the radio faceplate. Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume co...

  • Page 291

    To seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. Time button press the time button to alternate display of the time and radio frequency. Clo...

  • Page 292

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 293

    Set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored into pushbutton memory. The stations stored in set 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these butt...

  • Page 294

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 295

    Time button press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff press and hold the ff (fast forward) button and the cd player will begin to fast forward until ff is released, or rw or another cd button is pressed. The rw (reverse) bu...

  • Page 296

    The radio uses the following limits for file systems: • maximum number of folder levels: 8 • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file ...

  • Page 297

    Rates (vbr) are also supported. The majority of mp3 files use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bit rate. Mpeg specifi- cation sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio...

  • Page 298

    Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the user to plug in a portable device, such as an mp3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the dis...

  • Page 299

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 300

    Phone button uconnect™ phone — if equipped press this button to operate the uconnect™ phone feature (if equipped). Refer to “uconnect™ phone” in “under- standing the features if your vehicle”. If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with...

  • Page 301

    Info button press the info button for an rds station (one with call letters displayed). The radio will return a radio text message broadcast from an fm station (fm mode only). Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the directi...

  • Page 302

    Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Music type button pressing this button once will turn on the music type mode for five seconds. Pressing the music type button or turning the tune/scroll control knob within five seconds will allow the program for...

  • Page 303

    Program type 16-digit character display soft soft soft rock soft rck soft rhythm and blues soft r&b sports sports talk talk top 40 top 40 weather weather by pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected mu...

  • Page 304

    Window. Select the button (1–6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the set/ rnd button, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to e...

  • Page 305

    Inserting compact disc(s) gently insert one cd into the cd player with the cd label facing up. The cd will automatically be pulled into the cd player and the cd icon will illuminate on the radio display. If a cd does not go into the slot more than 1.0 in (2.5 cm), a disc may already be loaded and mu...

  • Page 306

    Note: ejecting with the ignition off is not allowed on convertible or soft-top models (if equipped). Seek button press the right seek button for the next selection on the cd. Press the left seek button to return to the beginning of the current selection, or return to the beginning of the previous se...

  • Page 307

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 308

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 309

    Loading times for playback of mp3 files may be affected by the following: • media - cd-rw media may take longer to load than cd-r media • medium formats - multisession discs may take longer to load than non-multisession discs • number of files and folders - loading times will increase with more file...

  • Page 310

    Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack which allows the user to plug in a portable device such as an mp3 player or cassette player and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the aux but...

  • Page 311

    System activation sirius satellite radio service is pre-activated and you may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your vehicle. Sirius will supply a wel- come kit that contains general information, includi...

  • Page 312

    Next, turn the knob surrounding the joystick in the center of the radio to scroll to subscription, and then press and release the joystick. All of the esns that apply to your vehicle will display. Selecting uconnect™ multimedia (satellite) mode press the sat button until ⬙ sat ⬙ appears in the displ...

  • Page 313

    Seek buttons press and release the seek buttons to search for the next channel in satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new channel until you make another selection. Holding either button will bypass channels without st...

  • Page 314

    Toggle the music type button again to select the music type. By pressing the seek button when the music type function is active, the radio will be tuned to the next channel with the same selected music type name. If a preset button is activated while in the music type (program type) mode, the music ...

  • Page 315

    You may add a second channel to each pushbutton by repeating the above procedure with this exception: press the set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2. This allows a total of 12 satellite channels to be stored into pushbutton memory. Th...

  • Page 316

    6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. Note: if you experience difficulty in playing a particu- lar disc, it may be damaged (i.E., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have pr...

  • Page 317

    Mode control the mode control allows you to choose from several pat- terns of air distribution as identified by the symbols. Panel air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. Bi-level air is directed through the panel and floor outlet...

  • Page 318

    Defrost air is directed through the windshield and side window demist outlets. Use this mode with maxi- mum fan and temperature settings for best windshield and side window defrosting. Blower control use this control (center rotary knob) to regulate the amount of air forced through the system in any...

  • Page 319

    Manual heating and air conditioning system — if equipped the controls for the heating/air conditioning and venti- lation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions. The instrument panel features four airflow reg...

  • Page 320

    Panel air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. Bi-level air is directed through the panel and floor outlets. Note: there is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to t...

  • Page 321

    Blower control use this control to regulate the amount of air forced through the system in any mode you select. The fan speed increases as you move the control to the right from the off position. Temperature control use this control to regulate the temperature of the air inside the passenger compart...

  • Page 322

    Note: continuous use of the “recirculation” mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. In cold or damp weather, the use of the “recirculation” mode will cause windows to fog on the inside because of moisture buildup inside the vehi...

  • Page 323

    Max a/c for maximum cooling, select ei- ther the panel or bi-level position using the mode control. Then, press the “a/c” and the “recir- culation” buttons so that both lights are illuminated, and set the temperature control to its coolest setting. Note: • recirculation mode will not operate in floo...

  • Page 324

    Smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging. Summer operation air conditioned vehicles must be protected with a high quality antifreeze coolant during summer to provide proper corrosion protection and to raise the boiling point of the coolant...

  • Page 326: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . 329 ▫ manual transmission – if equipped . . . . . . . 329 ▫ automatic transmission – if equipped . . . . . 330 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 330 ▫ extreme cold weather (below –...

  • Page 327

    ▫ automatic transmission with overdrive . . . . 339 䡵 four–wheel drive operation (command- trac i 威 or rock-trac 威 ) — if equipped . . . . . . . 343 ▫ operating instructions/precautions . . . . . . . 343 ▫ shift positions . . . . . . . . . . . . . . . . . . . . . . 345 ▫ shifting procedure . . . . ....

  • Page 328

    䡵 anti-lock brake system . . . . . . . . . . . . . . . . . 369 䡵 electronic brake control system . . . . . . . . . . . 371 ▫ anti-lock brake system (abs) . . . . . . . . . . . 371 ▫ traction control system (tcs) . . . . . . . . . . . 371 ▫ brake assist system (bas) . . . . . . . . . . . . . . 372 ▫ ...

  • Page 329

    ▫ base system . . . . . . . . . . . . . . . . . . . . . . . . 404 ▫ general information . . . . . . . . . . . . . . . . . . 407 䡵 fuel requirements . . . . . . . . . . . . . . . . . . . . . 407 ▫ reformulated gasoline . . . . . . . . . . . . . . . . 408 ▫ gasoline/oxygenate blends . . . . . . . . . ...

  • Page 330

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat buildup may cause serious injury or death. • never leave children i...

  • Page 331

    Automatic transmission – if equipped start the engine with the shift lever in the neutral or park position. Apply the brake before shifting to any driving range. Normal starting note: normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal. Tur...

  • Page 332

    If engine fails to start warning! • never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. • do not attempt to push or tow your vehicle to get it started. Vehicles equi...

  • Page 333

    If the engine shows no sign of starting after two 15– second periods of cranking with the accelerator pedal held to the floor, repeat the “normal starting” or “ex- treme cold weather” procedures. With tip start – automatic transmission only if the engine fails to start after you have followed the “n...

  • Page 334

    Warning! Remember to disconnect the cord before driving. Damage to the 110-115 volt ac electrical cord could cause electrocution. Use the heater when temperatures below 0°f (-18°c) are expected to last for several days. Manual transmission — if equipped warning! You or others could be injured if you...

  • Page 335

    Shifting fully press the clutch pedal before shifting gears. As you release the clutch pedal, lightly press the accelerator pedal. You should always use 1st gear when starting from a standing position if under heavy load or when pulling a trailer. Recommended vehicle shift speeds to utilize your man...

  • Page 336

    Downshifting moving from a high gear down to a lower gear is recommended to preserve brakes when driving down steep hills. In addition, downshifting at the right time provides better acceleration when you desire to resume speed. Downshift progressively. Do not skip gears to avoid overspeeding the en...

  • Page 337

    Manual transmission downshift speeds in mph (km/h) gear selec- tion 6 to 5 5 to 4 4 to 3 3 to 2 2 to 1 maxi- mum speed 80 (129) 70 (113) 50 (81) 30 (48) 15 (24) reverse shifting to shift into reverse, bring the vehicle to a complete stop. Press the clutch and pause briefly to allow the gear train to...

  • Page 338

    Caution! (continued) • do not shift from reverse, park, or neutral into any forward gear when the engine is above idle speed. • before shifting into any gear, make sure your foot is firmly on the brake pedal. Warning! It is dangerous to move the shift lever out of park or neutral if the engine speed...

  • Page 339

    Brake/transmission interlock manual override your vehicle may be equipped with a shift lock manual override. The manual override may be used in the event that the shift lever should fail to move from park with the key in the on position and the brake pedal pressed. To operate the shift lock manual o...

  • Page 340

    Automatic transmission with overdrive shifting from drive to park or reverse (or from p or r to d) should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake when moving the shift lever between these gears. Gear ranges note: under e...

  • Page 341

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • it is dangerous to move the shift lever out of park or neutral if the engine speed is higher than the idle...

  • Page 342

    • the shift lever is in drive. • the o/d off switch has not been activated. • vehicle speed is above approximately 30 mph (48 km/h). When frequent transmission shifting occurs while using overdrive, such as when operating the vehicle under heavy load conditions (for example, in hilly terrain, strong...

  • Page 343

    Second time restores the overdrive function. The lockout feature is useful when towing a trailer or carrying a heavy load. 2 (second) this range is used for moderate grades and to assist braking on dry pavement or in mud and snow. The vehicle begins from a stop in low gear with automatic upshift to ...

  • Page 344

    Torque converter clutch a feature designed to improve fuel economy has been added to the automatic transmission of this vehicle. A clutch within the torque converter engages automatically at calibrated speeds. This may result in a slightly differ- ent feeling or response during normal operation in h...

  • Page 345

    In the event that additional traction is required, the transfer case 4h and 4l positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed. This is accom- plished by simply moving the shift lever to one of these positions. The ...

  • Page 346

    Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the n (neutral) position without first fully engaging the parking brake. The transfer case n (neutral) position disengages both the front and rear driveshaft from the powertrain, and will allow the ...

  • Page 347

    Speed. This range (4l) provides additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). The “4wd indicator light” (located in the instrument cluster) will illuminate when the transfer case is shifted into the 4l position. Shifting procedu...

  • Page 348

    Warning! Failure to engage a position completely can cause transfer case damage or loss of power and vehicle control. You could have an injury accident. Do not drive the vehicle unless the transfer case is fully engaged. Trac-lok 姞 rear axle — if equipped the trac-lok 威 rear axle provides a constant...

  • Page 349

    Axle lock (tru–lok 姞 ) — rubicon models the axle lock switch is located on the lower switch bank (below the climate controls). This feature will only activate when the following con- ditions are met: • key in ignition, vehicle in 4l (low) range. • vehicle speed should be 10 mph (16 km/h) or less. To...

  • Page 350

    Rear axle lock (four-wheel drive non-rubicon models) — if equipped the rear axle lock switch is located on the lower switch bank (below the climate controls). This feature will only activate when the following con- ditions are met: • key in ignition, vehicle in 4l (low) range. • vehicle speed should...

  • Page 351

    Press the sway bar switch to activate the system. Press the switch again to deactivate the system. The “sway bar indicator light” (located in the instrument cluster) will illuminate when the bar is disconnected. The “sway bar indicator light” will flash during activation transition, or when activati...

  • Page 352

    To disconnect the stabilizer/sway bar, shift to either 4h or 4l and press the sway bar switch to obtain the off-road position. Refer to “four-wheel drive operation” in “starting and operating” for further information. The “sway bar indicator light” will flash until the stabilizer/ sway bar has been ...

  • Page 353

    An advantage of the higher ground clearance is a better view of the road, allowing you to anticipate problems. They are not designed for cornering at the same speeds as conventional two-wheel drive vehicles any more than low-slung sports cars are designed to perform satisfacto- rily in off-road cond...

  • Page 354

    3. Remove the side step assembly. The basics of off-road driving you will encounter many types of terrain driving off- road. You should be familiar with the terrain and area before proceeding. There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice...

  • Page 355

    Warning! Always wear your seat belt and firmly tie down cargo. Unsecured cargo can become projectiles in an off-road situation. When to use 4l (low) range when off-road driving, shift into 4l (low) for additional traction and control on slippery or difficult terrain, ascending or descending steep hi...

  • Page 356

    Caution! On icy or slippery roads, do not downshift at high engine rpm or vehicle speeds, because engine brak- ing may cause skidding and loss of control. Mud deep mud creates a great deal of suction around the tires and is very difficult to get through. You should use second gear (manual transmissi...

  • Page 357

    Caution! Reduced tire pressures may cause tire unseating and total loss of air pressure. To reduce the risk of tire unseating, while at a reduced tire pressure, reduce your speed and avoid sharp turns or abrupt maneu- vers. Crossing obstacles (rocks and other high points) while driving off-road, you...

  • Page 358

    Crossing large rocks when approaching large rocks, choose a path which ensures you drive over the largest of them with your tires. This will lift your undercarriage over the obstacle. The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse. Always look ahead...

  • Page 359

    On top of the log while the other just starts to climb the log. While climbing the log, modulate your brake and accelerator to avoid spinning the log out from under your tires. Then ease the vehicle off the log using your brakes. Caution! Do not attempt to cross a log with a greater diameter than th...

  • Page 360

    Before climbing a steep hill as you approach a hill, consider its grade or steepness. Determine if it is too steep. Look to see what the traction is on the hill side trail. Is the trail straight up and down? What is on top and the other side? Are there ruts, rocks, branches or other obstacles on the...

  • Page 361

    Driving downhill before driving down a steep hill, you need to determine if it is too steep for a safe descent. What is the surface traction? Is the grade too steep to maintain a slow, controlled descent? Are there obstacles? Is it a straight descent? Is there plenty of distance at the base of the h...

  • Page 362

    Engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock. Warning! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling the vehicle...

  • Page 363

    Caution! • water ingestion into the axles, transmission, trans- fer case, engine or vehicle interior can occur if you drive too fast or through too deep of water. Water can cause permanent damage to engine, driveline or other vehicle components, and your brakes will be less effective once wet and/or...

  • Page 364

    Caution! Muddy waters can reduce the cooling system effec- tiveness by depositing debris onto the radiator. Crossing ditches, streams, shallow rivers or other flowing water flowing water can be extremely dangerous. Never at- tempt to cross a fast running stream or river even in shallow water. Fast m...

  • Page 365

    Always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage. • inspect the radiato...

  • Page 366

    Power steering the standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible t...

  • Page 367

    Apparent, and/or the system is not functioning as antici- pated. Coordinate inspection efforts through an autho- rized dealer. Caution! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the new vehicle ...

  • Page 368

    When the parking brake is applied with the ignition switch on, the “brake warning light” in the instrument cluster will illuminate. Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime ...

  • Page 369

    Warning! • never use the park position on an automatic transmission as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • never leave children alone in a vehicle. Leaving unattended children in a veh...

  • Page 370

    Anti-lock brake system the anti-lock brake system (abs) is designed to aid the driver in maintaining vehicle control under adverse braking conditions. The system operates with a separate computer to modulate hydraulic pressure to prevent wheel lock-up and help avoid skidding on slippery surfaces. Al...

  • Page 371

    Warning! • pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • the anti-lock brake system (abs) cannot prevent the natural laws of physic...

  • Page 372

    Electronic brake control system your vehicle is equipped with an advanced electronic brake control system that includes anti-lock brake sys- tem (abs), traction control system (tcs), brake assist system (bas), hill start assist (hsa), electronic roll mitigation (erm), electronic stability program (e...

  • Page 373

    System functions similar to a limited slip differential and controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not ...

  • Page 374

    Hill start assist (hsa) the hsa system is designed to assist the driver when starting a vehicle from a stop on a hill. Hsa will maintain the level of brake pressure the driver applied for a short period of time after the driver takes their foot off of the brake pedal. If the driver does not apply th...

  • Page 375

    • gear selection matches vehicle uphill direction (i.E., vehicle facing uphill is in forward gear; vehicle back- ing uphill is in reverse gear). Warning! There may be situations on minor hills (i.E., less than 8%), with a loaded vehicle, or while pulling a trailer where the system will not activate ...

  • Page 376

    Towing with hsa hsa will provide assistance when starting on a grade when pulling a trailer. Warning! • if you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released there may not be enough...

  • Page 377

    3. With the engine running, the brake applied, and the clutch out, rotate the steering wheel 180° counterclock- wise from center. 4. Press the esp off switch four times within twenty seconds. 5. Rotate the steering wheel 360° clockwise (180° clock- wise from center). 6. Cycle ignition switch off the...

  • Page 378

    Warning! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift or rollover may occur. Electronic roll mitigation (erm) cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or ...

  • Page 379

    The “esp/tcs indicator light” begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. Warning! The electronic stability program (esp) cannot pre- vent the natural laws of phys...

  • Page 380

    Esp function normally. This mode is intended to be used if the vehicle is in deep snow, sand, or gravel conditions and more wheel spin than esp would normally allow is required to gain traction. To turn esp on again, momen- tarily press the esp off switch. This will restore the normal “esp on” mode ...

  • Page 381

    “compass and mini-trip computer – if equipped” in “understanding your instrument panel” for further in- formation. To turn esp on again, momentarily press the esp off switch. This will restore the normal “esp on” mode of operation. Note: • the esp system will change to “partial off” mode if the vehi...

  • Page 382

    Returns but tcs remains off. When the vehicle speed drops below 35 mph (40 km/h), the esp system shuts off. The esp is off at low vehicle speeds in 4l range so that it will not interfere with off-road driving, but the esp function returns to provide the stability feature at speeds above 40 mph (48 k...

  • Page 383

    Esp and defeat the functionality of the esp switch. Repeating the procedure will return the system to normal esp operation and restore esp switch functionality al- lowing esp “partial” or “off” modes. Warning! With esp in the permanent disable mode, enhanced vehicle stability offered by the esp and ...

  • Page 384

    8. Press and hold the esp off button for seven seconds. 9. Turn the steering wheel back to center. 10. Press and hold the esp off button for seven seconds. 11. Cycle the ignition key to off. After performing the esp disable procedure correctly, “esp off” will be displayed in the odometer for approxi...

  • Page 385

    Trailer sway control (tsc) tsc uses sensors in the vehicle to recognize an exces- sively swaying trailer and will take the appropriate actions to attempt to stop the sway. The system may reduce engine power and apply the brake of the appro- priate wheel(s) to counteract the sway of the trailer. Tsc ...

  • Page 386

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 387

    Tires designed to this standard have the letter “t” molded into the sidewall preceding the size designa- tion. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards, and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 r15 lt. Tire sizing...

  • Page 388

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 389

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 390

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold tire pressure cold tire inflation pressure is defined as the tire pressure after ...

  • Page 391

    Tire loading and tire pressure tire placard location tire placard location (two-door models) tire placard location (four-door models) 390 starting and operating.

  • Page 392

    Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loa...

  • Page 393

    Combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for determining correct load limit 1. Locate the statement “the combined weight of occu- pants and cargo should never exceed xxx kg or xxx lbs” on your vehicle’...

  • Page 394

    5 starting and operating 393.

  • Page 395

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 396

    Economy improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under-inflation also increases tire rolling resistance and results in higher fuel consumption. R...

  • Page 397

    Tire pressure should be checked and adjusted as well as inspected for signs of tire wear or visible damage, at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated ev...

  • Page 398

    Tire pressures change by approximately 1 psi (7 kpa) per 12° f (7° c) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter. Example: if garage temperature = 68° f (20° c) and the outside temperature = 32° f (0° c) then the cold tire infla...

  • Page 399

    Radial-ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial tires in sets of four. Never combine them with other types of tires. Cuts and punctures in radial tire...

  • Page 400

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Life of tire the service life of a tire is dependent upon varying factors includi...

  • Page 401

    Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance wh...

  • Page 402

    Warning! (continued) • failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. Caution! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Tire rotation reco...

  • Page 403

    The suggested rotation method is the “forward-cross” shown in the following diagram. Tire pressure monitor system (tpms) the tire pressure monitoring system (tpms) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. The tire pressure will vary with tem...

  • Page 404

    Cold placard pressure. Once the “tire pressure monitor- ing telltale light” has been illuminated, the tire pressure must be increased to the recommended cold placard pressure in order for the “tire pressure monitoring telltale light” to be turned off. The system will auto- matically update and the “...

  • Page 405

    Caution! (continued) • after inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the tire pressure moni- toring sensor. Note: • the tpms is not intended to replace normal tire care and ma...

  • Page 406

    The tire pressure monitor system (tpms) consists of the following components: • receiver module • four tire pressure monitoring sensors • tire pressure monitoring telltale light a tire pressure monitoring sensor is located in the spare wheel if the vehicle is equipped with a matching full size spare...

  • Page 407

    2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with tpm sensors. Note: • if your vehicle is equipped with a matching full-size s...

  • Page 408

    Below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the tpms to receive this information. General information this device complies with part 15 of the fcc rules and rss 210 of industry c...

  • Page 409

    Over 40 auto manufacturer’s worldwide have issued and endorsed consistent gasoline specifications (the world- wide fuel charter, wwfc) to define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recom- mends the use of gasoline th...

  • Page 410

    E-85 usage in non-flex fuel vehicles non-ffv vehicles are compatible with gasoline contain- ing 10% ethanol (e10). Gasoline with higher ethanol content may void the vehicle’s warranty. If a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all of these symptoms: • ...

  • Page 411

    It is even more important to look for gasoline without mmt in canada, because mmt can be used at levels higher than those allowed in the united states. Mmt is prohibited in federal and california- reformulated gasoline. Materials added to fuel all gasoline sold in the united states is required to co...

  • Page 412

    Caution! (continued) • the use of fuel additives which are now being sold as octane enhancers is not recommended. Most of these products contain high concentra- tions of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsi...

  • Page 413

    Warning! (continued) • guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnor- mal conditions repaired promptly. Until repaired, drive with all side windows fully open. • keep the swing gate closed when driving your v...

  • Page 414

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impu- rities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “malfunction indi- cator light (mil)” to illuminate, due to f...

  • Page 415

    Loose fuel filler cap message after fuel has been added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improperly installed, or damaged. If the system detects a malfunction, the “gascap” message will display in the odometer display. Tighten the gas cap until a...

  • Page 416

    Payload the payload of a vehicle is defined as the allowable load weight a truck or any given vehicle can carry, including the weight of the driver, all passengers, options and cargo. Gross axle weight rating (gawr) the gawr is the maximum permissible load on the front and rear axles. The load must ...

  • Page 417

    The entire vehicle should first be weighed on a commer- cial scale to ensure that the gvwr has not been ex- ceeded. The weight on the front and rear of the vehicle should then be determined separately to be sure that the load is properly distributed over front and rear axle. Weighing the vehicle may...

  • Page 418

    Common towing definitions the following trailer towing-related definitions will as- sist you in understanding the following information: gross vehicle weight rating (gvwr) the gvwr is the total allowable weight of your vehicle. This includes driver, passengers, cargo and trailer tongue weight. The t...

  • Page 419

    Trailer tongue weight (tw) the trailer tongue weight is the downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle. Frontal area the frontal area is the max...

  • Page 420

    Warning! • an improperly adjusted weight-distributing hitch system may reduce handling, stability, braking performance, and could result in an accident. • weight-distributing hitch systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputabl...

  • Page 421

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.8...

  • Page 422

    Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.8l/automatic 4.10 two–door rubicon model (4wd) 6,366 lbs (2 887 kg) 25 sq ft (2.32 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.8l/automatic 3.73 four–door x ...

  • Page 423

    Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.8l/automatic 3.73 four–door sahara model (4wd) 8,127 lbs (3 686 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.8l/manual 4.10 four–door ru...

  • Page 424

    Consider the following items when computing the weight on the rear axle of the vehicle: • the trailer tongue weight. • the weight of any other type of cargo or equipment put in or on your vehicle. • the weight of the driver and all passengers. Note: remember that everything put into or on the traile...

  • Page 425

    Caution! • do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle. Thi...

  • Page 426

    Warning! (continued) • vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in park. With a manual transmis- sion, shift the transmission into first gear. And with four-wheel-drive vehicles, make ...

  • Page 427

    − check for signs of tire wear or visible tire damage before towing a trailer. Refer to “tires – general information” in “starting and operating” for the proper inspection procedure. − when replacing tires, refer to “tires – general infor- mation” in “starting and operating” for proper tire replacem...

  • Page 428

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Warning! • do not connect trailer brake...

  • Page 429

    The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustration. Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual tra...

  • Page 430

    The automatic transmission fluid and filter should be changed if you regularly tow a trailer for more than 45 minutes of continuous operation. Refer to “mainte- nance schedule” for the proper maintenance intervals. Note: check the automatic transmission fluid level before towing. O/d off to reduce t...

  • Page 431

    Recreational towing (behind motorhome, etc.) caution! Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing. Two-wheel drive models recreational towing is allowed only if the rear d...

  • Page 432

    Four-wheel drive models note: the transfer case must be shifted into n (neu- tral), automatic transmission must be shifted into park, and manual transmission must be placed in gear (not in neutral) for recreational towing. Shifting into neutral (n) warning! You or others could be injured if you leav...

  • Page 433

    7. Release the brake pedal and ensure that there is no vehicle movement. 8. Turn the engine off and turn the ignition switch to the acc position. 9. Shift the automatic transmission into park. 10. Apply the parking brake. 11. Attach the vehicle to the tow vehicle with the tow bar. 12. Release the pa...

  • Page 434

    3. Shift the transfer case lever into the desired position. 4. Start the engine. 5. Shift the automatic transmission into drive or release the clutch on manual transmissions. Note: when shifting out of transfer case n (neutral) on automatic transmission-equipped vehicles, turning the engine off may ...

  • Page 436: Contents

    What to do in emergencies contents 䡵 hazard warning flasher . . . . . . . . . . . . . . . . 436 䡵 if your engine overheats . . . . . . . . . . . . . . . . 436 䡵 jacking and tire changing . . . . . . . . . . . . . . . 438 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . 438 ▫ spare tire ...

  • Page 437

    Hazard warning flasher the hazard warning flasher switch is located on the lower switch bank below the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. ...

  • Page 438

    Note: there are steps that you can take to slow down an impending overheat condition: • if your air conditioner (a/c) is on, turn it off. The a/c system adds heat to the engine cooling system and turning the a/c off can help remove this heat. • you can also turn the temperature control to maximum he...

  • Page 439

    Jacking and tire changing warning! • getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center wh...

  • Page 440

    Spare tire stowage to remove the spare tire from the carrier, remove the tire cover, if equipped, and remove the lug nuts with the lug wrench turning them counterclockwise. Note: if you have added aftermarket accessories to the spare tire mounted carrier, it cannot exceed a gross weight of 50 lbs (2...

  • Page 441

    Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • block the wheel diagonally opposite the wheel to...

  • Page 442

    1. Remove the spare tire, jack and tools from the stored location. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. 3. Assemble the jack and jacking tools. Connect the jack handle driver to the extension, then to the lug wr...

  • Page 443

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position the spare wheel/tire on the vehicle and inst...

  • Page 444

    Jump-starting procedures if your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump-starting can be dangerous if done improperly so please follow the procedures in this section caref...

  • Page 445

    Preparations for jump-start the battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly. Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by m...

  • Page 446

    3. If using a another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is off. Warning! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-sta...

  • Page 447

    Warning! Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then st...

  • Page 448

    Emergency tow hooks — if equipped if your vehicle is equipped with tow hooks, they are mounted in the front and the rear. Note: for off-road recovery, it is recommended to use both of the front tow hooks to minimize the risk of damage to the vehicle. Warning! • chains are not recommended for freeing...

  • Page 450: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment – 3.8l . . . . . . . . . . . . . . 451 䡵 onboard diagnostic system — obd ii . . . . . . 452 ▫ loose fuel filler cap message . . . . . . . . . . . 452 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 451

    ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . 471 ▫ automatic transmission – if equipped . . . . . 473 ▫ hydraulic clutch fluid – manual transmission . . . . . . . . . . . . . . . . . . . . . . . 475 ▫ manual transmission – if equipped . . . . . . . 475 ▫ transfer case – if equipped ....

  • Page 452

    Engine compartment – 3.8l 1 — integrated power module 7 — washer fluid reservoir 2 — battery 8 — engine coolant reservoir 3 — automatic transmission dipstick 9 — air cleaner filter 4 — engine oil fill 10 — coolant pressure cap 5 — engine oil dipstick 11 — power steering fluid reservoir 6 — brake flu...

  • Page 453

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 454

    The message will appear the next time the vehicle is started. This might indicate a damaged cap. If the prob- lem is detected twice in a row, the system will turn on the mil. Resolving the problem will turn the mil off. Emissions inspection and maintenance programs in some localities, it may be a le...

  • Page 455

    4. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m...

  • Page 456

    Your vehicle. Refer to these manuals before attempting any procedure yourself. Note: intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. Warning! You can be badly injured working on or around a motor vehicle. Onl...

  • Page 457

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or ...

  • Page 458

    Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to “maintenance schedule” for further information. Note: under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, whichev...

  • Page 459

    Engine oil viscosity (sae grade) sae 5w-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil fi...

  • Page 460

    Engine oil filter selection all of the manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replace- ment. The quality of replacement filters varies consider- ably. Only high quality filters should be used to assure most efficient service. Mopar 威 engine ...

  • Page 461

    Caution! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and are identified on the battery case. Also, if a “fast charger”...

  • Page 462

    Warning! (continued) • the air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced repairman. Note: use only manufacturer approved ...

  • Page 463

    Amount of a high quality lubricant, such as mopar 威 lock cylinder lubricant or equivalent, directly into the lock cylinder. Windshield wiper blades clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non-abrasive cleaner. This will remove...

  • Page 464

    Exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. Warning! Commercial windshield washer solvents are flam- mable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust syst...

  • Page 465

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Caution! Damage to the catalytic converter can result if your vehicle is n...

  • Page 466

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires dis...

  • Page 467

    Garden hose vertically down the face of the a/c con- denser (if equipped) or the back of the radiator core. Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator. Inspect the entire system for leak...

  • Page 468

    Caution! • mixing of engine coolant (antifreeze) other than the specified hoat engine coolant (antifreeze) may result in engine damage and may decrease corrosion protection. If a non-hoat engine cool- ant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with ...

  • Page 469

    When adding engine coolant (antifreeze): • the manufacturer recommends using mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid organic additive technology) or equivalent. • mix a minimum solution of 50% hoat engine coolant (antifreeze) and distilled water. Use higher concentra- tio...

  • Page 470

    Warning! The warning words do not open hot on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the en- gine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To preve...

  • Page 471

    When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine co...

  • Page 472

    • do not change the thermostat for summer or winter operation. If replacement is ever necessary, install only the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mileage, and increased emissions. Brake system in order to assure brake system performan...

  • Page 473

    Warning! • use only manufacturer’s recommended brake fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid ...

  • Page 474

    Warning! (continued) • do not allow petroleum based fluid to contami- nate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in an accident. Automatic transmission – if equipped selection of lubricant it is important that the proper...

  • Page 475

    To properly check the automatic transmission fluid level, the following procedure must be used: 1. Operate the engine at idle speed and normal operating temperature. 2. The vehicle must be on level ground. 3. Fully apply the parking brake. 4. Place the shift lever momentarily into each gear posi- ti...

  • Page 476

    7. Check for leaks. Release the parking brake. Note: to prevent dirt and water from entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is properly reseated. It is normal for the dipstick cap to spring back slightly from its fully seated position, as lo...

  • Page 477

    Fluid level check check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more than 3/16 in (4.76 mm) below the bottom of the hole. Add fluid, if necessary, to maintain the proper level. Frequency of fluid change under normal ope...

  • Page 478

    Caution! When replacing the plugs, do not overtighten them. You could damage them and cause them to leak. Selection of lubricant use only manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Front/rear axle fluid fl...

  • Page 479

    Conceal damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts. Check the air conditioning drain tube on the lower dash wall in the engine compart- ment for mud or debris, and clean as required. A plugged tube will adversely affect air conditioning performance. Caution! Under fre...

  • Page 480

    • salt in the air near sea-coast localities. • atmospheric fallout/industrial pollutants. • bird droppings. Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar 威 car wash or equiva- lent, or a mild car wash soap, and rinse the panels completely with clear water...

  • Page 481

    • it is important that the drain holes in the lower edges of the doors, rocker panels and tailgate are kept clear and open. • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle ...

  • Page 482

    Interior care use mopar 威 total clean or equivalent to clean fabric upholstery and carpeting. Interior trim should be cleaned starting with a damp cloth, a damp cloth with mopar 威 total clean or equiva- lent, then mopar 威 spot & stain remover or equivalent if absolutely necessary. Do not use harsh c...

  • Page 483

    Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet, soft rag. A mild soap solution may be used, but do not use high alcohol co...

  • Page 484

    • be especially careful when washing the windows by following the directions for “care of fabric top windows.” washing — use mopar 威 car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles. If extra cleaning is required, use mopar 威 con- vertible cloth top cleaner o...

  • Page 485

    Care of fabric top windows caution! Your vehicle’s fabric top has pliable plastic windows which can be scratched unless special care is taken by following these directions: 1. Never use a dry cloth to remove dust. Instead, use a microfiber towel or soft cotton cloth moistened with cold or warm, clea...

  • Page 486

    If a stuck zipper slide is experienced, work the mopar 威 soft top zipper cleaner and lubricant or equivalent into the zipper slide. Several applications may be required before the zipper comes free. 6. Never paste stickers, gummed labels or any tape to the windows. Adhesives are hard to remove and m...

  • Page 487

    Cavity cartridge fuse mini fuse description j4 25 amp natural driver door node j5 25 amp natural passenger door node j6 40 amp green anti-lock brake system (abs) pump feed/esp j7 30 amp pink anti-lock brake system (abs) valve feed/esp j8 — — j9 40 amp green pzev sec motor feed/ flex fuel j10 30 amp ...

  • Page 488

    Cavity cartridge fuse mini fuse description j22 — spare m1 15 amp blue center high-mounted stop light (chmsl)/ switch stop lamp feed m2 20 amp yellow relay trailer lighting (stop) m3 20 amp yellow frt/rear axle locker relay m4 — — m5 — — m6 20 amp yellow power outlet #1/rain sensor m7 20 amp yellow ...

  • Page 489

    Cavity cartridge fuse mini fuse description m12 30 amp green amplifier (amp) m13 20 amp yellow ignition off draw – cabin compartment node (iod-ccn), wire- less control module (wcm), siren, multi- function control switch (multifctn sw) m14 20 amp yellow trailer tow (export only) cavity cartridge fuse...

  • Page 490

    Cavity cartridge fuse mini fuse description m16 10 amp red occupant restraint controller (orc) m17 15 amp blue left tail/license/park lamp (lt-tail/lic/ prk lmp) m18 15 amp blue right tail/park/run lamp (rt-tail/prk/ run lmp) m19 25 amp natural auto shut down (asd #1 and #2) m20 15 amp blue cabin co...

  • Page 491

    Cavity cartridge fuse mini fuse description m30 15 amp blue wiper motor frt, j1962 diagnostic feed m31 20 amp yellow backup lamps (b/u lamps) m32 10 amp red occupant restraint controller (orc), tt europe m33 10 amp red next generation con- troller (ngc), global powertrain engine con- troller (gpec) ...

  • Page 492

    Cavity cartridge fuse mini fuse description m38 25 amp natural lock/unlock motors (lock/unlock mtrs) caution! • when installing the integrated power module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the integrat...

  • Page 493

    • or, disconnect the negative cable from the battery. • anytime you store your vehicle, or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will ensure adequate system lubricat...

  • Page 494

    Bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Headlamp 1. Open hood and support u...

  • Page 495

    Front park/turn signal 1. Remove the front grille. Turn the retainers along the top 1/4 turn counterclockwise and remove. 2. Pull the bottom of the grille away starting at one side and working toward the other. 3. Turn the socket assembly 1/4 turn counterclockwise and remove from housing. Pull the b...

  • Page 496

    Rear tail, stop, turn signal, and backup lamp 1. Remove the two inboard screws attaching the tail light housing to the body. Do not remove the outer screws at any time. 2. Separate the housing from the body by pushing the lamp inboard while pulling the lamp away from the body. 3. Rotate the appropri...

  • Page 497

    Fluid capacities u.S. Metric fuel (approximate) — two door models 18.5 gallons 70 liters fuel (approximate) — four door models 22.5 gallons 85 liters engine oil with filter 3.8 liter engine 6 quarts 5.7 liters cooling system * 3.8 liter engine (mopar 威 antifreeze/engine coolant 5 year/100,000 mile f...

  • Page 498

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid organic additive technology) or equivalent. Engine oil use api certified sae 5w-20 engine oil, meeting the requirements of chrysl...

  • Page 499

    Chassis component fluid, lubricant, or genuine part automatic transmission – if equipped mopar 威 atf+4 威 automatic transmission fluid or equivalent licensed atf+4 威 product. Manual transmission – if equipped mopar 威 manual transmission lubricant or equivalent (meeting the re- quirements of chrysler ...

  • Page 500: Maintenance Schedules

    Maintenance schedules contents 䡵 emissions control system maintenance . . . . . . 500 䡵 maintenance schedule . . . . . . . . . . . . . . . . . . 500 ▫ required maintenance intervals . . . . . . . . . . 502 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 501

    Emissions control system maintenance the scheduled maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done t...

  • Page 502

    • change your engine oil more often if you drive your vehicle off-road for an extended period of time. • under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, which- ever comes first. Your dealer will reset the oil change indicator message after completing ...

  • Page 503

    Once a month • check tire pressure and look for unusual wear or damage. • inspect the battery and clean and tighten the terminals as required. • check the fluid levels of coolant reservoir, brake master cylinder, power steering and transmission and add as needed. • check all lights and other electri...

  • Page 504

    6,000 miles (10,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 12,000 miles (20,000 km) or 12 months maintenance service schedule ❏ change the engine...

  • Page 505

    18,000 miles (30,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ inspect the front & rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer reading date repair order # dea...

  • Page 506

    30,000 miles (50,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ change the manual transmission fluid if using your veh...

  • Page 507

    36,000 miles (60,000 km) or 36 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake linings, ...

  • Page 508

    48,000 miles (80,000 km) or 48 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake linings, ...

  • Page 509

    60,000 miles (100,000 km) or 60 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ inspect the brake linings, replace if necessary. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ ch...

  • Page 510

    66,000 miles (110,000 km) or 66 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 72,000 miles (120,000 km) or 72 months maintenance service schedule ❏ change the en...

  • Page 511

    78,000 miles (130,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 84,000 miles (140,000 km) or 84 months maintenance service schedule ❏ change the en...

  • Page 512

    90,000 miles (150,000 km) or 90 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ inspect and replace pcv valve if necessary.† ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ change...

  • Page 513

    96,000 miles (160,000 km) or 96 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake linings,...

  • Page 514

    108,000 miles (180,000 km) or 108 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake lining...

  • Page 515

    120,000 miles (200,000 km) or 120 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ replace accessory drive belt(s). ❏ inspect the brake linings, replace if necessary. ❏ inspect exhaust system. ❏ inspect the ...

  • Page 516

    126,000 miles (210,000 km) or 126 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ inspect the front & rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer reading date repair order # ...

  • Page 517

    138,000 miles (230,000 km) or 138 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 144,000 miles (240,000 km) or 144 months maintenance service schedule ❏ change th...

  • Page 518

    150,000 miles (250,000 km) or 150 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ change the manual transmission fluid if using your ...

  • Page 519

    † this maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about...

  • Page 520: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 521 ▫ prepare for the appointment . . . . . . . . . . . 521 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 521 ▫ be reasonable with r...

  • Page 521

    䡵 publication order forms . . . . . . . . . . . . . . . . 525 䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 527 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 527 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 5...

  • Page 522

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 523

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 524

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 525

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to reso...

  • Page 526

    If nhtsa receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. T...

  • Page 527

    • service manuals these comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing chrysler group llc vehicles. A complete working knowledge of the vehicle, system, and/or...

  • Page 528

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle....

  • Page 529

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 530: Index

    Index 10

  • Page 531

    Abs (anti-lock brake system) . . . . . . . . . . . . 251,369 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 412 air cleaner, engine (engine air cleaner filter) . . . 459 air conditioner maintenance . . . . . . . . . . . . . . . 460 air conditioning . . . . . . . . . . . . . . . . ...

  • Page 532

    Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459 keyless transmitter replacement (rke) . . . . . . . 23 belts, seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39,77 body mechanism lubrication . . . . . . . . . . . . . . . 461 brake assist system . . . . . . . . ...

  • Page 533

    Child seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 climate control . . . . . . . . . . . . . . . . . . . . . . . . . 315 clock . . . . . . . . . . . . . . . . . . . . . 270,285,286,290,299 compact disc (cd) maintenance . . . . . . . . . . . . . 314 compass . . . . . . . . . . ...

  • Page 534

    Disposal engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 458 used coolant (antifreeze) . . . . . . . . . . . . . . . . 469 door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 driver’s seat...

  • Page 535

    Fuel requirements . . . . . . . . . . . . . . . . . . 407,496 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . 443 oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456,496 oil disposal . . . . . . . . . . . . . . . . . . . . . . . . . . 458 oil filter . . . . . . . . . ...

  • Page 536

    Fog light service . . . . . . . . . . . . . . . . . . . . . . . . 494 fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . 135,494 fold and tumble rear seat . . . . . . . . . . . . . . . . . 126 folding rear seat . . . . . . . . . . . . . . . . . . . . . . . . 129 folding windshield . . . ...

  • Page 537

    Hands-free phone (uconnect™) . . . . . . . . . . . . . . 86 hard top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 hard top, modular . . . . . . . . . . . . . . . . . . . . . . 156 hard top removal . . . . . . . . . . . . . . . . . . . . . . . 164 hazard warning flasher . . . . . . ....

  • Page 538

    Jack location . . . . . . . . . . . . . . . . . . . . . . . . . . . 438 jack operation . . . . . . . . . . . . . . . . . . . . 438,440,441 jacking instructions . . . . . . . . . . . . . . . . . . . . . . 440 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . 443 key, programming . . ....

  • Page 539

    Electronic stability program (esp) indicator . . . . . . . . . . . . . . . . . . . . . . . . . 261,383 electronic throttle control warning . . . . . . . . . 262 engine temperature warning . . . . . . . . . . . . . . 252 exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 fog . . ...

  • Page 540

    Maintenance free battery . . . . . . . . . . . . . . . . . . 459 maintenance procedures . . . . . . . . . . . . . . . . . . . 455 maintenance schedule . . . . . . . . . . . . . . . . . . . . 500 malfunction indicator light (check engine) . . 259,453 manual, service . . . . . . . . . . . . . . . . . ...

  • Page 541

    Recommendation . . . . . . . . . . . . . . . . . . . 457,496 viscosity . . . . . . . . . . . . . . . . . . . . . . . . . 458,496 oil pressure light . . . . . . . . . . . . . . . . . . . . . . . 249 onboard diagnostic system . . . . . . . . . . . . . . 452,453 operator manual (owner’s manual) . . . ....

  • Page 542

    Shifting into transfer case neutral (n) . . . . . . . 431 shifting out of transfer case neutral (n) . . . . . 432 reformulated gasoline . . . . . . . . . . . . . . . . . . . . 408 refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461 release, hood . . . . . . . . . . . . . . . . . ...

  • Page 543

    Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 482 pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . 47 reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 adjustment . . . . ....

  • Page 544

    Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329 automatic transmission . . . . . . . . . . . . . . . . . 330 cold weather . . . . . . . . . . . . . . . . . . . . . . . . . 330 engine block heater . . . . . . . . . . . . . . . . . . . . 332 engine fails to start . . . . . ....

  • Page 545

    Inflation pressures . . . . . . . . . . . . . . . . . . . . . 395 jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 438,441 load capacity . . . . . . . . . . . . . . . . . . . . . 390,391 pressure monitor system (tpms) . . . . . . . . . . . 402 pressure warning light . . . . . . . . . . ...

  • Page 546

    Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 476 transmission automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . 339 maintenance . . . . . . . . . . . . . . . . . . . . . . . 473,475 manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333 range indicator . ...

  • Page 547

    Window fogging . . . . . . . . . . . . . . . . . . . . . . . . 322 windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 windshield defroster . . . . . . . . . . . . . . . . . . . . . . 77 windshield, folding . ....

  • Page 548

    Chrysler group llc 10jk72-126-ab 2nd edition printed in u.S.A..