- DL manuals
- Jeep
- Automobile
- Jeep Wrangler
- Owner's Manual
Jeep Jeep Wrangler Owner's Manual
Summary of Jeep Wrangler
Page 1
Wrangler o w n e r ’ s m a n u a l 2 0 0 8 2 0 0 8 w ra n g le r 81-326-0855 first edition printed in u.S.A..
Page 2: Table Of Contents
Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the ...
Page 4: Introduction
Introduction contents m introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m rollover warning . . . . . . . . . . . . . . . . . . . . . . . . 5 m how to use this manual . . . . . . . . . . . . . . . . . . 6 m warnings and cautions . . . . . . . . . . . . . . . . . . . 8 m vehicle i...
Page 5
Introduction this is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive enclosed vehicles were not intended. It handles and maneuvers differently from many passenger cars both on-road and off-road, so ta...
Page 6
When it comes to service, remember that your authorized dealer knows your vehicle best, has the factory-trained technicians and genuine mopar t parts, and is interested in your satisfaction. Rollover warning utility vehicles have a significantly higher roll over rate than other types of vehicles. Th...
Page 7
Or death. Because of its open-body construction, your vehicle offers less protection than closed vehicles in the event of an accident. Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of exis...
Page 8
Introduction 7 1.
Page 9
Warnings and cautions this manual contains warnings against operating procedures, which could result in an accident or bodily injury. It also contains cautions against procedures, which could result in damage to your vehicle. If you do not read this entire manual, you may miss important information....
Page 10: Contents
Things to know before starting your vehicle contents m a word about your keys . . . . . . . . . . . . . . . . . .12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .12 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .13 m steering wheel lock . . . . . . . . . . . . . . . . . . . ...
Page 11
▫ to turn off “flash lights with lock” . . . . . . . .21 ▫ programming additional transmitters . . . . . . . .21 ▫ general information . . . . . . . . . . . . . . . . . . . .22 ▫ battery replacement . . . . . . . . . . . . . . . . . . . .23 m remote starting system — if equipped . . . . . . . .24 m ...
Page 12
▫ driver and front passenger supplemental restraint systems (srs) . . . . . . . . . . . . . . . . . .47 ▫ child restraint . . . . . . . . . . . . . . . . . . . . . . . .58 m engine break-in recommendations . . . . . . . . . . .71 m safety tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .7...
Page 13
A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your dealer to give you the number. The key code can also be obtained by the dealer from your vehicle invoice. Ignition key removal manual...
Page 14
Warning! Leaving children in a vehicle unattended is danger- ous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal, or the gear selector lever. Do not leave the keys in the ignition. A child could operate power windows,...
Page 15
To release the steering wheel lock insert the key in the ignition and turn the wheel slightly to the right or left to disengage the lock. Note: if you turned the wheel to the right to engage the lock, you must turn the wheel slightly to the right to disengage it. If you turned the wheel to the left ...
Page 16
Longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle ser- viced as soon as possible. Note: • the sentry key immobilizer system is not compatible with some after-market remote starting systems. Use of these systems may result in vehicle s...
Page 17
Authorized dealer or by using the customer key pro- gramming procedure. This procedure consists of pro- gramming a blank key to the vehicle electronics. A blank key is one, which has never been programmed. Note: when having the sentry key immobilizer system serviced, bring all vehicle keys with you ...
Page 18
The new sentry key is programmed. The keyless entry transmitter will also be programmed during this pro- cedure. Repeat this procedure to program up to 8 keys. If you do not have a programmed sentry key, contact your dealer for details. Note: if a programmed key is lost, see your dealer to have all ...
Page 19
To set the alarm the alarm will set when you use the remote keyless entry transmitter to lock the doors and swing gate or when you use the power door lock switch while the door is open. After all the doors are locked and closed, the “sentry key/security alarm indicator light” (located in the instrum...
Page 20
Remote keyless entry — if equipped this system allows you to lock or unlock the doors and swing gate or activate the panic alarm from distances a maximum of 66 feet (20 meters) using a hand held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system. Note: the l...
Page 21
4. Test the feature while outside of the vehicle, by pressing the “lock/unlock” button on the keyfob. Note: pressing the “lock” button on the keyfob while you are inside the vehicle will activate the security alarm. Opening a door with the security alarm activated will cause the alarm to sound. Pres...
Page 22
To turn off “flash lights with lock” note: the flash lights with lock feature can be turned on or off by performing the following steps: 1. Press the “unlock” button for 4 to 10 seconds. 2. While the “unlock” button is pressed, (after 4 seconds) press the “lock” button. Release both buttons. 3. Test...
Page 23
4. Turn the ignition to the on position ( do not start the engine ). 5. Press and hold the “unlock” button on the key fob. 6. After holding the “unlock” button for four seconds, also press the panic button within 6 seconds. 7. When a single chime is heard release both buttons. The chime is an indica...
Page 24
Note: changes or modifications not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. If your remote lock control fails to operate from a normal distance, check for these two conditions. 1. Weak batteries in transmitter. The expecte...
Page 25
2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To assemble the transmitter case, snap the two halves together. Note: if the key fob is equipped with a screw,...
Page 26
Once the vehicle has started, the engine will run for 15 minutes. To cancel remote start, press the “remote start” button once. The parking lamps will remain illuminated to indicate that the vehicle has remote started and the engine is running. The lamps will turn off when the ignition is turned to ...
Page 27
Doors the vacuum fluorescent (vf) display located in the odometer area displays the word “door” as an indication of a door ajar or door not completely closed. When the vehicle is not moving and the door is ajar or not completely closed, the vf display will show the word “door.” if any other active w...
Page 28
3. Unhook door strap from the body hook. Be careful not to allow door to swing fully open as mirror may damage paint. 4. With the door open, lift the door to clear hinge pins from their hinges, and remove door. To reinstall the door(s), perform the above steps in the opposite order. Rear door remova...
Page 29
3. Remove interior b-pillar trim access door at bottom of b-pillar. 4. Unplug wiring harness connector. 5. Unhook door strap from the body hook. 6. With the door open, lift the door to clear hinge pins from their hinges, and remove door. To reinstall the door(s), perform the above steps in the oppos...
Page 30
Door locks the vacuum fluorescent (vf) display located in the odom- eter area displays the word “door” as an indication of a door ajar or door not completely closed. When the vehicle is not moving and the door is ajar or not completely closed, the vf display will show the word “door.” if any other a...
Page 31
Warning! • for personal security reasons and safety in an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. • never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could ...
Page 32
Warning! • for personal security reasons and safety in an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. • never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could ...
Page 33
Automatic unlock doors on exit programming the automatic unlock doors on exit feature can be enabled or disabled as follows: 1. Close all doors and place the key in the ignition. 2. Cycle the ignition switch between lock and on and then back to lock 4 times ending up in the lock position. 3. Depress...
Page 34
2. Cycle the ignition switch between lock and on and then back to lock 4 times ending up in the lock position. 3. Depress the power door lock switch to lock the doors. 4. A single chime will indicate the completion of the programming. 5. Repeat these steps if you want to return this feature to its p...
Page 35
Auto down both the driver and front passenger window switch has an “auto down” feature. Press the window switch past the first detent, release, and the window will go down automatically. To cancel the “auto down” movement, operate the switch in either the up or down direction and release the switch....
Page 36
Window lockout switch (4 door models only) the window lockout switch (located between the win- dow switches) allows you to disable the rear window switches that are located on the back of the center floor console. To disable the window controls, press the win- dow lockout button downward. To enable ...
Page 37
The swing gate can be unlocked using the remote keyless entry, or by activating the power door lock switches located on the front doors. To open the swing gate, press the button on the gate handle. Note: close flip-up window before swing gate (hard top models only). Caution! Do not press on rear wip...
Page 38
Occupant restraints some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger, and side airbags (if equipped) for both the driver and front...
Page 39
Research has shown that seat belts save lives, and that they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the veh...
Page 40
Warning! • wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse....
Page 41
3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” latch plate latch plate to buckle 40 things to know before starting your vehicle.
Page 42
Warning! A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. A belt that is loose will not protect you as well. In a sudden stop you coul...
Page 43
Warning! A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug. A twisted belt cannot do its job as well. In a collision it...
Page 44
Rear center lap/shoulder belt retractor lock-out (4 door models only) this feature is designed to lock the retractor whenever the 60% rear seat back is not fully latched. This prevents someone from wearing the rear center lap/shoulder belt when the rear seat back is not fully latched. Note: • if the...
Page 45
Adjustable upper shoulder belt anchorage in the front seat positions, the shoulder belt anchorage can be adjusted upward or downward to position the belt away from your neck. Push in on the anchorage near your outside shoulder and slide it up or down to reach the position that serves you best. Warni...
Page 46
Seat belt pretensioners the driver and front passenger seat belts are equipped with a pretensioning device that is designed to remove any slack from the seat belt systems in the event of a collision. This device improves the performance of the seat belt by assuring that the belt is tight around the ...
Page 47
The enhanced warning system (beltalert) can be en- abled or disabled by your authorized dealer or by following these steps: note: the following steps must occur within the first 60 seconds of the ignition switch being turned to the on or start position. The manufacturer does not recom- mend deactiva...
Page 48
Seat belt extender if a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. Wh...
Page 49
This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel. The passenger side airbag is mounted in the instrument panel, above the glove compartment. The words srs are embossed...
Page 50
Warning! • do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are infla...
Page 51
Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years and under should always ride buckled up in a rear seat. Infants in rear facing child restraints should never ride in the front seat of a vehicle with a passenger airbag. An airbag deplo...
Page 52
Warning! • relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • being too close to the steering wh...
Page 53
• driver and passenger seat track position sensors • driver and front passenger seat belt pretensioner how the airbag system works • the occupant restraint control (orc) module de- termines if a frontal, or side collision is severe enough to require the front and/or side airbags to inflate. The fron...
Page 54
• the driver and passenger airbag/inflator units are located in the center of the steering wheel and the right side of the instrument panel. When the orc detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the front airba...
Page 55
• the knee impact bolsters help protect the knees of the driver and the front passenger, and position every- one for the best interaction with the front airbag. If a deployment occurs the airbag system is designed to deploy when the occupant restraint control (orc) module detects a moderate-to-sever...
Page 56
• it is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you. Warning! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensio...
Page 57
Note: perchlorate material – special handling may apply, see www.Dtsc.Ca.Gov/hazardouswaste/perchlorate airbag warning light you will want to have the airbag system ready to inflate for your protection in an impact. The airbag system is designed to be maintenance free. If any of the following occurs...
Page 58
In conjunction with other data gathered during a com- plete accident investigation, the electronic data may be used by daimlerchrysler corporation and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle perfor- mance. In addition t...
Page 59
Data parameters that may be recorded: • diagnostic trouble code(s) and warning lamp status for electronically-controlled safety systems, including the airbag system • airbag disable lamp status (if equipped) • 9 time 9 of airbag deployment (in terms of ignition cycles and vehicle mileage) • airbag d...
Page 60
There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the correct seat for your child. Use the restraint that is correct for your child. Warning! In a c...
Page 61
• rearward-facing child seats must never be used in the front seat of a vehicle with the front passenger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position. Warning! • improper installation can lead to failure of an infant or c...
Page 62
Necessary to use a locking clip. For the seat belt with the automatic locking retractor, pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then, pull the belt until it is fully extracted from the retract...
Page 63
Older children and child restraints children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction, are for chil- dren who weigh 20 to 40 lbs (9 to 18 kg), ...
Page 64
Automatic-locking retractor (alr) to operate the switchable retractor, pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then pull on the belt until it is all removed from the retractor. Allow the belt t...
Page 65
Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap. Latch — child seat anchorage system (lower anchors and tether for children) yo...
Page 66
Restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child. Remind all children in the vehicle that the seat belts are not t...
Page 67
Latch anchorages (2 door models) latch anchorages (4 door models) 66 things to know before starting your vehicle.
Page 68
In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjustin...
Page 69
Hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap. You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages. Next attach the lower hooks or co...
Page 70
If the seat belt has a automatic locking retractor, it will have a distinctive label. Pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then, pull the belt until it is all extracted from the retractor. A...
Page 71
Route the tether strap over the seat back and attach the hook to the tether anchor located on the back of the seat. For the outboard seating positions, route the tether under the head rest, and attach the hook to the tether anchor located on the back of the seat. Warning! An incorrectly anchored tet...
Page 72
Engine break-in recommendations a long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle accelerat...
Page 73
Garage, and never sit in a parked vehicle with the engine running for a extended period. If the vehicle is stopped in an open area with engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle. • guard against carbon monoxide with proper...
Page 74
Airbag warning light the light should come on and remain on for 6 to 8 seconds as a indicator check when the ignition switch is first turned on. If the indicator is not lit during starting, have it serviced. If the light stays on or comes on while driving, have the system checked by an authorized de...
Page 76: Contents
Understanding the features of your vehicle contents m mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 ▫ inside day/night mirror . . . . . . . . . . . . . . . . .79 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . .80 m hands–free communication (uconnect™) . . . ....
Page 77
M lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 ▫ interior lights . . . . . . . . . . . . . . . . . . . . . . . .91 ▫ multi-function control lever . . . . . . . . . . . . . .92 ▫ parking lights, instrument panel lights, and headlights . . . . . . . . . . . . . . . . . . . ...
Page 78
▫ abs (anti-lock brake system) . . . . . . . . . . . . 100 ▫ tcs (traction control system) . . . . . . . . . . . . 101 ▫ bas (brake assist system) . . . . . . . . . . . . . . . 102 ▫ erm (electronic roll mitigation) . . . . . . . . . . 103 ▫ esp (electronic stability program) . . . . . . . . . 104 ▫...
Page 79
▫ door frame installation (4 door models) . . . . 132 m soft top (2 door models) . . . . . . . . . . . . . . . . . 134 ▫ folding down the soft top . . . . . . . . . . . . . . 136 ▫ putting up the soft top . . . . . . . . . . . . . . . . 145 m sunrider — 2 door models . . . . . . . . . . . . . . . . ...
Page 80
Mirrors inside day/night mirror the mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Annoying headlight glare can be reduced by moving the small control under the mirror to the night positio...
Page 81
Outside mirrors to receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! • vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they ...
Page 82
Hands–free communication (uconnect™) this feature is not available on wrangler (2 door) or wrangler unlimited (4 door) models. Voice recognition button (uconnect™ hands free phone) when you press this button, a “uconnect™ system not available” message will display on your radio screen. Phone button ...
Page 83
Front seat adjustment move seat forward or rearward by lifting the lever. Be sure the latch engages fully. Manual seat height adjustment — if equipped the driver’s seat height can be raised or lowered, by using the ratcheting handle on the outboard side of the seat. Pull upward on the handle to rais...
Page 84
Front seat back recline to recline: 1. Lean forward before lifting the handle, then lean back to the desired position and release the handle. 2. Lift the handle to return the seatback to an upright position. Front passenger easy entry seat (2 door models) push the lever on the seatback rearward (tow...
Page 85
1. To return the seat to a sitting position, rotate the seat back upright until it locks. 2. Push the seat rearward until the track locks. Note: the front passenger seat has a full recliner memory, which will allow the seat back to be returned to it’s original position. Note: the front passenger sea...
Page 86
Fold and tumble rear seat (2 door models) note: prior to folding the rear seat, it may be necessary to reposition the front seats. Also, be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily. 1. Lift the seatback release lever and fo...
Page 87
2. Slowly flip the entire seat forward. 3. When completed, return seat to it’s normal position. 4. Raise the rear seatback using the assist strap and firmly lock seat into position. Removing the rear seat (2 door models) warning! • it is extremely dangerous to ride in a cargo area, inside or outside...
Page 88
1. Remove the rear subwoofer (if equipped) mounting screws (3) using a #t30 torx t head driver. 2. Unplug electrical connector from rear subwoofer (if equipped). 3. Fold the rear seat forward following steps 1 through 3 under “fold and tumble rear seat” in this section. 4. Press down on release bar ...
Page 89
Replacing the rear seat (2 door models) reverse steps for removing the seat. Warning! • to help protect against personal injury, passengers should not be seated in the rear cargo area with the rear seat folded down or removed from the ve- hicle. • the rear cargo space is intended for load carrying p...
Page 90
To fold down the rear seat locate the pull strap (lower outboard side of seat) and pull towards you until the seat back releases. To raise the rear seat 1. Raise the seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficult...
Page 91
To open and close the hood to open hood, first release both hood latches. Next, locate handle in middle of the front end of the hood. Insert hand into gap between hood and top of grille, and push handle to the side to raise hood. You may have to push down slightly on hood before pushing the handle. ...
Page 92
Lights interior lights the overhead light comes on when a door is opened. It may also be turned on by rotating the control for the dimmer switch on the multi-function control lever fully upward. The overhead light will automatically turn off in about 20 minutes if a door is left open or the dimmer c...
Page 93
Doors to stay open for extended periods of time without discharging the vehicle’s battery. Daytime brightness feature certain instrument panel components (odometer, radio display) can be illuminated at full brightness during the daytime. This can be helpful when driving with your headlights on durin...
Page 94
Parking lights, instrument panel lights, and headlights turn the end of the multi-function control lever to the first detent for parking lights and instrument panel lights. Turn to the second detent for headlight operation. To change the brightness of the instrument panel lights, rotate the center p...
Page 95
Passing light you can signal another vehicle with your headlights by lightly pulling the multi-function control lever toward the steering wheel. This will cause the headlights to turn on at high beam and remain on until the lever is released. Front fog lights — if equipped the front fog light switch...
Page 96
Windshield wipers and washers caution! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is ...
Page 97
Windshield washers to use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for two wipe cycles after the lever is released, and then resume the intermit- tent interval previously selected. If the lever is p...
Page 98
Warning! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving. Electronic speed control — if equ...
Page 99
To activate push the on/off button. The cruise indicator light in the instrument cluster will illuminate. To turn the system off, push the on/off button a second time. The cruise indicator light will turn off. The system should be turned off when not in use. Warning! Leaving the electronic speed con...
Page 100
To resume speed to resume a previously set speed, push the “resume accel” lever up and release. Resume can be used at any speed above 20 mph (32 km/h). To vary the speed setting when the speed control is on, speed can be increased by pushing up and holding “resume accel”. Release the lever when the ...
Page 101
Warning! Speed control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use speed control in heavy traffic or on roads that are winding, icy, snow-covered, or slipp...
Page 102
Warning! Abs (anti-lock brake system) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Abs cannot prevent accidents, in- cluding those resulting from excessive speed in turns, driving on very slippery surf...
Page 103
Bas (brake assist system) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce...
Page 104
Erm (electronic roll mitigation) this system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When erm determines that the rate of change of the steering wheel angle and vehicles speed are sufficient to potentially cause wheel lif...
Page 105
Esp (electronic stability program) this system enhances directional control and stability of the vehicle under various driving conditions. Esp cor- rects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counter- acting the over/under steer condition....
Page 106
Warning! Esp (electronic stability program) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esp cannot prevent accidents, in- cluding those resulting from excessive speed in turns, driving on very slipper...
Page 107
Conditions and more wheel spin than esp would nor- mally allow is required to gain traction. To turn esp on again, momentarily depress the 9 esp control switch 9 . This will restore the normal “esp on” mode of operation. Note: to improve the vehicle’s traction when driving with snow chains, or start...
Page 108
Refer to “compass and mini-trip computer — if equipped” in section 4 of this manual. To turn esp on again, momentarily depress the 9 esp control switch 9 . This will restore the normal “esp on” mode of operation. Note: the esp system will change to “partial off” mode if the vehicle speed exceeds 40 ...
Page 109
4wd low range esp off this is the normal operating mode for esp in 4wd low range. Whenever the vehicle is started in 4wd low range, or the transfer case (if equipped) is shifted from 4wd high range or neutral to 4wd low range, the esp system will be in this mode. In 4wd low range, esp and tcs, excep...
Page 110
Esp/bas warning lamp the malfunction indicator lamp for the esp is combined with the bas indicator. The yellow “esp/bas warning lamp” in the instrument cluster comes on when the ignition switch is turned to the “on” position. It should go out with the engine running. If the “esp/bas warning lamp” co...
Page 111
Electrical power outlet this vehicle has two auxiliary power outlets that can provide up to 20 amps of current for accessories de- signed for use with the standard power outlet adapters. The outlet located in the lower portion of the instrument panel has a snap on plastic cap so that it can be cover...
Page 112
Electrical outlet use with engine off warning! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E. Cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or p...
Page 113
The rear passengers have cup holders at the rear of the center console. Storage console storage compartment to lock or unlock, insert ignition key and turn. To open, press the latch and lift cover. Rear cup holders center console 112 understanding the features of your vehicle.
Page 114
Rear storage compartment the rear storage compartment cover is held by a spring loaded latch. In order to remove the rear storage com- partment cover, use the following procedure: note: the rear storage compartment latch should not be used as cargo tie-down. 1. Flip up pull loop so it is perpendicul...
Page 115
Dual top — if equipped if your vehicle is equipped with a dual top, you must remove one of the tops from the vehicle. If the soft top is removed, the pivot brackets must also be removed from the sport bar. The soft top was installed at the factory for shipping purposes only. The soft top and the har...
Page 116
3. Remove the soft top bow assembly pivot bracket screws (2 per side) using a #t30 torx t head driver. 4. Using a rubber mallet, carefully tap the knuckles from the left and right metal pivot brackets. Remove the soft top from the vehicle and store in a clean, dry location. Understanding the feature...
Page 117
5. Unzip the zipper on the sport bar cover to expose the pivot brackets. Remove the brackets using a #t30 torx t head driver. Recover and re-zip the sports bar cover. Store pivot brackets and screws in a safe place. 6. Reinstall the hard top. Refer to “freedom top 3 — piece modular hard top — front/...
Page 118
3. Install the door frames. Refer to “door frame” in this section. 4. If the soft top has been removed, follow these steps to reinstall the soft top. If the soft top is on the vehicle, proceed to step #5. A. If the pivot brackets have been removed, unzip the sport bar covers and attach the pivot bra...
Page 119
C. Tap the knuckles on the side with a rubber mallet to reattach them to the metal pivot brackets. D. Screw the pivot screws back into place using a #t30 torx t head driver. Secure them until they are snug being careful not to cross-thread the screws or over tighten. Caution! Do not overtighten the ...
Page 120
5. Unsnap and remove the black boot cover. This cover should be discarded. It was intended as a protective cover for shipping only. Note: a visual instruction sheet is enclosed in the dual top wrap. 6. Remove the swing gate bar (black metal bar for bottom of rear window) and set aside. Note: be sure...
Page 121
Front panel(s) removal note: left panel must be removed before removing right panel. 1. Fold down the sun visor, and move to the side. 2. Turn center l-shaped locks (2) from center of roof panel. 3. Turn rear l-shaped lock (located above shoulder belt anchorage). 4. Turn rear fasteners (knobs) (loca...
Page 122
5. Unlatch the header panel latch located at the top of the windshield. 6. Remove panel. To remove right panel, follow steps above except for step 2. Understanding the features of your vehicle 121 3.
Page 123
Front panel(s) installation note: the front panel (s) must be positioned properly to ensure sealing. Set the panels on the windshield frame so that there is no overhang. Also, make sure that the panels are sitting flush with the body. 1. Install right panel first, then the left panel. 2. Reinstall p...
Page 124
3. Reinstall panel(s) using the same steps for removal in reverse order. Rear hard top removal 1. Remove both front panels. Refer to “front panel(s) removal” in this section. 2. Open both doors. 3. Remove the two (2) torx t head screws which secure the hard top at the b-pillar (near top of door) usi...
Page 125
6. Locate the wiring harness on the left rear inside corner of the vehicle. 7. Disconnect the washer hose and install the tethered cap. Caution! Make sure storage cap is installed to prevent foreign materials from entering tube and clogging system, and also prevent fluid from being sprayed into rear...
Page 126
9. Close the swing gate. 10. Remove the hard top from the vehicle. Place on a soft surface to prevent damage. Rear hard top installation note: if the door frames are installed from soft top usage, they must be removed prior to installation of the hard top. 1. Inspect the hard top seals for damage an...
Page 127
Door frame warning! Do not drive your vehicle on-pavement with the door frame(s) removed as you lose the protection they can provide. This procedure is furnished for use during off-road operation only. Door frame removal (2 door models) 1. Unscrew and remove the door frame attachment knobs (2 per si...
Page 128
2. Place one hand on the upper rear and one hand on the front of the door frame. 3. Pull the frame towards you with your rearward hand to remove the frame from the vehicle. 4. Screw the knobs back into the door frame and fold for storage. Store in a secure location. Warning! Never store the door fra...
Page 129
Door frame installation (2 door models) 1. Unfold door frame and unscrew thumbscrews. 2. Set the door frame pin into the hole on top of the body side, behind the door opening. 3. After the door frame pin has been set into the bodys- ide hole, carefully set the front of the door frame into the rubber...
Page 130
5. Starting with the front knob, screw in and tighten both knobs. Repeat on the other side. Door frame removal (4 door models) 1. Unscrew and remove the two (2) forward most door frame attachment knobs. Understanding the features of your vehicle 129 3.
Page 131
Warning! Use both hands to remove the door frames. The door frames will fold and could cause injury if both hands are not used. 2. Place one hand on the upper rear and one hand on the upper front of the front door frame. 3. Pull the frame towards you with your front hand to remove the frame from the...
Page 132
5. Place one hand on the upper rear and one hand on the upper front of the rear door frame. Pull the frame towards you with your rear hand to remove the frame from the vehicle. 6. Screw the knob back into the door frame and fold for storage. Store in a secure location. Warning! • never store the doo...
Page 133
Door frame installation (4 door models) 1. Install the rear door frame first. 2. Set the door frame pin into the hole on top of the body side, just behind the rear door opening. 3. Position the top of the door frame against the metal sport bar and press onto the side bar making sure not to pinch the...
Page 134
Front of the door rail over the side bar making sure that the material for the side bar cover is not pinched by the door frame. Position the rear of the front door frame to lay on top of the front of the rear door frame. 6. Loosely install both knobs beginning with the front knob (long knob). Then, ...
Page 135
Soft top (2 door models) caution! • the soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle, and thus cannot properly carry any additional ...
Page 136
Caution! • do not run a fabric top through an automatic car wash. Window scratches and wax build up may result. • do not lower the top when the temperature is below 41°f (5°c). Damage to the top may result. • do not move your vehicle until the top has been either fully attached to the windshield fra...
Page 137
Folding down the soft top 1 — header bow 6 — body side retainer 2 — 2 bow 7 — quarter window 3 — 3 bow 8 — check strap 4 — sail panel 9 — front retainer — quarter window 5 — plastic retainer 10 — bottom retainer — quarter window 136 understanding the features of your vehicle.
Page 138
1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels understanding the features of your vehicle 137 3.
Page 139
Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...
Page 140
4. Release the header latches and leave the hooks in the loops on the windshield. 5. Open the swing gate. 6. Before unzipping the rear window, release the first three (3) inches of both sail panels from the channel. Remove the swing gate bar by pulling it straight rear- ward out of the swing gate br...
Page 141
• unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across the top and down to the left lower corner. Zipper pulls will stay on the rear window. Pull down on the rear window to disengage from the zipper on the top cover. Stow the windows carefully to avoid s...
Page 142
10. Finish releasing the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 11. As you begin to lower the top, fold the sail panels so that they rest on top of the soft to...
Page 143
12. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in towards the vehicle to disengage. 13. Completely release the latches from the loops on the w...
Page 144
14. Make sure the plastic sleeves are slid forward over the sunrider link (sunrider models only). 15. Unlatch the side bows from both door rails (sunrider models only). Understanding the features of your vehicle 143 3.
Page 145
16. Before lowering the top, open the swing gate to prevent possible damage to the rear center mounted brake lamp. Move to the front of the vehicle. Grasp the side bow behind the header and lift the top, folding it toward the rear of the vehicle. 17. Tuck the fabric and the check straps between the ...
Page 146
Putting up the soft top 1 — header bow 6 — body side retainer 2 — 2 bow 7 — quarter window 3 — 3 bow 8 — check strap 4 — sail panel 9 — front retainer — quarter window 5 — plastic retainer 10 — bottom retainer — quarter window understanding the features of your vehicle 145 3.
Page 147
1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 146 understanding the features of your vehicle.
Page 148
1. Unclip and move the sun visors to the side. 2. Install door frames, if removed. Refer to “door frame” in this section. 3. Make sure the plastic sleeve is slid rearward over sunrider link (sunrider models only). 4. Standing on the side of the vehicle, lift the top by the side bow and the 2–bow (mi...
Page 149
5. Before attaching the header latches, be sure that the top retainers above the door are not trapped between the top and the door frame. 6. Make sure the sunrider bracket on the side bows latches to the door rails (sunrider models only). 7. Open the header latches and engage the hook on each side o...
Page 150
8. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel until it snaps onto the exterior part of the rail. To be properly located, the bracket must only be clipped to the ...
Page 151
10. Partially install the sail panel retainers into the body side channel, leaving the last three (3) inches towards the rear window loose (on both sides). Pulling down on the rear roof bow (3 bow) will aid to reach the channel with the retainers. 11. To install the side windows, affix the window te...
Page 152
12. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can result in wind and water leaks or damage to the window. 13. Continue closing the zipper only along the top edge of the window. U...
Page 153
14. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro t along the top and rear of the window. Repeat this step for the opposite side. 15...
Page 154
16. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage. 17. Run the zipper fully around to the right side of the window. 18. Grasp the swing gate bar and p...
Page 155
20. Open the doors and insert the roof retainers into the channels above the door, starting at the front and work- ing rearward. 21. Close the header latches and return the sun visors to their secured position. 154 understanding the features of your vehicle.
Page 156
Sunrider — 2 door models note: if you are going to be driving faster than 40 mph (64 km/h) with the sunrider feature open, it is recom- mended that you remove the rear window of the vehicle. To open 1. Insert finger behind the plastic retainer. Pull down and roll the retainer out of the channel. Rep...
Page 157
3. Release the header latches from the loops on the windshield frame. 4. Slide the plastic sleeve forward. 156 understanding the features of your vehicle.
Page 158
5. Grasp the header and lift the top back. Make sure the material is folded back as shown. 6. Locate straps to secure side bows. Wrap straps around bows as shown. Repeat on the other side. 7. Reposition sun visors. Understanding the features of your vehicle 157 3.
Page 159
To close 1. Remove straps from side bows. 2. Unclip and move sun visors to the side. 3. Grasp the front header and pull to the front of the vehicle. 4. Hook header latches to the loops on the windshield frame, close latches, and return sun visor’s to their original position. 5. Slide plastic sleeve ...
Page 160
2. Unclip and move the sun visors to the side. 3. Release the header latches from the loops on the windshield frame. Understanding the features of your vehicle 159 3.
Page 161
4. Grasp the front side bow behind the header, and lift the top. 5. Fold back the front section of the top, and gently rest the header on top of the rear portion of the deck. 160 understanding the features of your vehicle.
Page 162
6. Fold the top material so that the plastic retainers form a “w” as shown. Enter the vehicle, and move the material into two folds. Ensure that the straps are securely stowed. 7. Close the front header latches. 8. Secure the top by using the two (2) provided straps. Each strap will wrap around the ...
Page 163
Soft top (4 door models) caution! • the soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle, and thus cannot properly carry any additional ...
Page 164
Caution! • do not run a fabric top through an automatic car wash. Window scratches and wax build up may result. • do not lower the top when the temperature is below 41°f (5°c). Damage to the top may result. • do not lower the top when the windows are dirty. Grit may scratch the window. • do not move...
Page 165
Folding down the soft top 1 — header bow 6 — body side retainer 11 — plastic retainer 2 — 2 bow 7 — quarter window 3 — 3 bow 8 — check strap 4 — 4 bow 9 — front retainer — quarter window 5 — sail panel 10 — bottom retainer — quarter window 164 understanding the features of your vehicle.
Page 166
1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels understanding the features of your vehicle 165 3.
Page 167
Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...
Page 168
4. Release the header latches and hooks from the loops on the windshield frame. 5. Open the swing gate. 6. Before unzipping the rear window, release the first three (3) inches of both sail panels from the channel. Remove the swing gate bar by pulling it straight rear- ward out of the swing gate brac...
Page 169
• unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across the top and down to the left lower corner. Zipper pulls will stay on the rear window. Pull down on the rear window to disengage from the zipper on the top cover. Stow the windows carefully to avoid s...
Page 170
10. Finish releasing the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 11. Fold the sail panels so that they rest on top of the soft top. Understanding the features o...
Page 171
12. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in towards the vehicle to disengage. 13. Grasp the front side bow behind the header, and lift t...
Page 172
14. Fold back the front section of the top, and gently rest the header on top of the rear portion of the deck. 15. Fold the top material so that the plastic retainers form a “w” as shown. Enter the vehicle, and move the material into two folds. Understanding the features of your vehicle 171 3.
Page 173
16. Release the side bows by pressing down on the latch above the front of the rear door. Push the top rearward to disengage. Repeat this step on the other side. 17. Grasp the folded side bows and slide the top along the door frame track to the rear door frame. 172 understanding the features of your...
Page 174
18. Before lowering the top, open the swing gate to prevent possible damage to the rear center mounted brake lamp. Gently slide the side bows off the door frame track and lower the top down into the vehicle. 19. Tuck the fabric and the check straps between the bows as far inside as possible. This wi...
Page 175
Putting up the soft top 1 — header bow 6 — body side retainer 11 — plastic retainer 2 — 2 bow 7 — quarter window 3 — 3 bow 8 — check strap 4 — 4 bow 9 — front retainer — quarter window 5 — sail panel 10 — bottom retainer — quarter window 174 understanding the features of your vehicle.
Page 176
1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels understanding the features of your vehicle 175 3.
Page 177
Note: be extremely careful when putting up the soft top to prevent the doors from getting scratched. It may be helpful to open the rear doors. 1. Install the door frames, if removed. Refer to “door frame” in this section. 2. Undo the straps used to secure the top in the down position and store in se...
Page 178
5. Insert the slider feature of the knuckles into the door frame tracks and slide the top forward. 6. Ensure that the top locks into sunrider locking mecha- nisms that are located above the front of the rear doors. 7. Unclip and move the sun visors to the side. Understanding the features of your veh...
Page 179
8. Standing on the side of the vehicle, lift the top by the side bow until it rests on the windshield frame. 9. Before attaching the header latches, be sure the top retainers above the doors do not get trapped between the top and the door frame. Also, make certain the feet at both ends of the 2 bow ...
Page 180
10. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 11. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel...
Page 181
13. Partially install the sail panel retainers into the body side channel, leaving the last three (3) inches towards the rear window loose (on both sides). Pulling down on the rear roof bow (4 bow) will aid to reach the channel with the retainers. 14. To install the side windows, affix the window te...
Page 182
15. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can result in wind and water leaks or damage to the window. 16. Continue closing the zipper only along the top edge of the window. U...
Page 183
17. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro t along the top and rear of the window. Repeat this step for the opposite side. 18...
Page 184
19. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage. 20. Run the first zipper fully around to the right side of the window. 21. Grasp the swing gate bar...
Page 185
23. Open the doors and insert the top retainers into the channels in the door frame above the doors, starting at the front and work toward the rear of the vehicle. 24. Ensure plastic retainer is tucked in properly at b-pillar not pinching seal. 184 understanding the features of your vehicle.
Page 186
25. Close the header latches and return the sun visors to their secured position. Folding windshield the fold down windshield and removable side bars on your vehicle are structural elements that can provide some protection in some accidents. The windshield also provides some protection against weath...
Page 187
Raise the windshield and reinstall the side bars as soon as the task that required their removal is completed and before you return to on-road driving. Both you and your passenger should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down...
Page 188
Lowering the windshield and removing side bars 1. Lower the fabric top or remove the hard top following the instructions in this manual. Note: to assist in properly reinstalling side bars, mark the original locations prior to removing. 2. Remove the 2 top hex bolts (13mm), and the 1 side hex bolt (1...
Page 189
Note: pull side bar out horizontally when removing. Caution! Do not remove the head impact foam from the side bars, as damage to the foam may result. Note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping. 5. Remove side bar assembly, and reattach sport ba...
Page 190
7. Remove the windshield wiper arms by first pulling the wiper away from the windshield and out to the “lock” position. Unsnap the wiper arm nut caps, and remove retaining nuts. Lift the wiper arms off and store in center console or securely behind the rear seat. 8. Remove the lower windshield plate...
Page 191
Raising the windshield and replacing side bars 1. Raise the windshield. 2. Loosely attach rear of side bar to sport bar. Refer to step 4 of “lowering windshield and removing side bars” earlier in this section. • reattach sport bar velcro covering. 3. Attach front of side bar to windshield frame. • i...
Page 192
5. Install the lower windshield plates with the 6 black round headed torx t head screws (using a #40 torx t head driver) on each side of the base of the windshield. 6. Reinstall wiper arms. Rear window features — hard top only rear window wiper/washer — if equipped a rotary ring switch on the contro...
Page 193
If the rear wiper is operating when the ignition is turned off, the wiper will automatically return to the “park” position. When the vehicle is restarted, the wiper will resume function at whichever position the switch is set at. Adding washer fluid the fluid reservoir for the windshield washers and...
Page 194
The defroster will automatically turn off after about ten minutes. For five more minutes of operation, press the switch again. To prevent excessive battery drain, use the defroster only when the engine is operating. Caution! Use care when washing the inside of the rear window to prevent damage to he...
Page 196: Contents
Understanding your instrument panel contents m instrument panel and controls . . . . . . . . . . . . . 198 m instrument cluster . . . . . . . . . . . . . . . . . . . . . . 199 m instrument cluster description . . . . . . . . . . . . . 200 m compass and trip computer — if equipped . . . 210 ▫ control...
Page 197
▫ list button (cd mode for mp3 play) . . . . . . . 227 ▫ info button (cd mode for mp3 play) . . . . . . . 227 m sales code req — am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 ▫ operating instructions - radio mode ....
Page 198
▫ operating instructions - video entertainment system (ves t ) (if equipped) . . . . . . . . . . . . . 249 m cd/dvd disc maintenance . . . . . . . . . . . . . . . 249 m radio operation and cellular phones . . . . . . . . 250 m climate controls . . . . . . . . . . . . . . . . . . . . . . . 250 ▫ manu...
Page 199
Instrument panel and controls 1 — air outlet 6 — climate controls 2 — instrument cluster 7 — power outlet 3 — horn 8 — lower switch bank 4 — radio 9 — auxiliary power outlet 5 — glove box 198 understanding your instrument panel.
Page 200
Instrument cluster understanding your instrument panel 199 4.
Page 201
Instrument cluster description your vehicle is equipped with the instrument cluster described on the following pages. 1. Fuel gauge the pointer shows the level of fuel in the fuel tank. When the fuel gauge pointer initially moves to e, for your safety, approximately 2 u.S. Gallons (7.6l) of fuel rem...
Page 202
6. Front axle lock indicator light — if equipped indicates when the front axle lock has been activated. 7. Seat belt indicator light a warning chime and an indicator light will alert you to buckle the seat belts. When the belt is buckled, the chime will stop, but the light will stay on until it time...
Page 203
11. Brake warning light after ignition is turned on, illuminates to indicate function check at vehicle start-up. Indicates park- ing brake is applied. If the light stays on when the parking brake is off, it indicates a possible brake system fluid leak or low pressure level, see your authorized deale...
Page 204
14. Rear axle lock indicator light — if equipped indicates when the rear axle lock has been activated. 15. Tachometer indicates the engine speed in revolutions per minute (rpm). Caution! Do not operate the engine with the tachometer pointer in the red area. Engine damage will occur. 16. Engine coola...
Page 205
20. 4wd indicator light — if equipped this light alerts the driver that the vehicle is in the four-wheel drive mode, and the front and rear driveshafts are mechanically locked to- gether forcing the front and rear wheels to rotate at the same speed. 21. Odometer/trip odometer reset button press this...
Page 206
Reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the tpms is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the lev...
Page 207
Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, t...
Page 208
Change oil message your vehicle is equipped with an engine oil change indicator system. The “change oil” message will flash in the instrument cluster odometer for approximately 12 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indic...
Page 209
Stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not require towing. When the engine is running, the “malfunction indicator light” may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic convert...
Page 210
29. Electronic stability program (esp) warning light/brake assist system (bas) warning light the esp/bas warning light in the instrument cluster comes on when the ignition switch is turned to the “on” position. The light should go out with the engine running. If the esp/ bas warning light comes on c...
Page 211
32. Compass/mini-trip computer button—if equipped press this button to switch between the different func- tions. Compass and trip computer — if equipped this feature, located on the instrument cluster (speedom- eter and tachometer), displays information on outside temperature, compass direction, and...
Page 212
Reset press and hold the right button (on the instrument cluster) while function is being displayed to reset. The following trip conditions can be reset: • avg eco (changes to present fuel economy) • et trip conditions average fuel economy (avg eco) this display shows the average fuel economy since ...
Page 213
Compass temperature display this display provides the outside temperature and one of eight compass readings to indicate the direction the vehicle is facing. Warning! Even if the display still reads a few degrees above 32°f ( 0°c), the road surface may be icy, particularly in woods or on bridges. Dri...
Page 214
Manual compass calibration note: before attempting a manual compass calibra- tion, the engine must be running and the transmission in the p (park) position (if equipped). Compass calibration can also be requested. To manually calibrate the compass, you must first enter the variance mode. Press the a...
Page 215
To increment the zone. The default is zone 8. After zone 15, the values will wrap around to zone 1. When the correct zone is displayed (per the compass variance zone map) for the zone that the vehicle is located in, wait for about 5 seconds, then the trip computer will store the variance value in me...
Page 216
Outside temperature if the outside temperature is more than 131°f (55°c), the display will show 131°f (55°c). When the outside tem- perature is less than 2 40°f ( 2 40°c), the display will show 2 40°f ( 2 40°c). Radio general information radio broadcast signals your new radio will provide excellent ...
Page 217
Fm reception because fm transmission is based on frequency varia- tions, interference that consists of amplitude variations can be filtered out, leaving the reception relatively clear, which is the major feature of fm radio. Note: the radio, steering wheel radio controls (if equipped), and 6 disc cd...
Page 218
Power switch/volume control (rotary) press the on/volume control knob to turn on the radio. Press the on/volume control knob a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the...
Page 219
Phone button (uconnect™ hands free phone) — if equipped press this button to operate the hand free phone (ucon- nect™) feature (if equipped). Refer to “hands-free com- munication (uconnect™)” in section 3 for more informa- tion. If your vehicle is not equipped with or this feature is not available o...
Page 220
Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either am or fm frequencies. Tune control turn the right side rotary control clockwise to increase or counter-clockwise to decrease t...
Page 221
Allow the program format type to be selected. Many radio stations do not currently broadcast music type informa- tion. Toggle the music type button to select the following format types: program type 16 digit-character display no program type or un- defined none adult hits adlt hit classical classicl...
Page 222
By pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the...
Page 223
Stations to be stored into push-button memory. The stations stored in set 2 memory can be selected by pressing the push-button twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to push-but...
Page 224
Caution! • this cd player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. • do not use adhesive labels. These labels can peel away and jam the player mechanism. • res is a single cd player. Do not attempt to insert a second cd if one is alr...
Page 225
Time button press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff press the rw button to stop the cd at the beginning of the current cd track/title. Press and hold ff (fast forward) and the cd player will begin to fast forward until ff...
Page 226
Files properly and may be unable to play the file nor- mally. Udf and apple hfs formats are not supported. The radio uses the following limits for file systems: • maximum number of folder levels: 8 • maximum number of files: 255 • maximum number of folders (the radio display of file names and folder...
Page 227
Rates (vbr) are also supported. The majority of mp3 files use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bit rates. Mpeg specifi- cation sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audi...
Page 228
List button (cd mode for mp3 play) pressing the list button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the tune control knob. Selecting a folder by pressing the tune control knob will begin playing the files contained in that folder (or the next...
Page 229
Time button (auxiliary mode) press this button to change the display to time of day. The time of day will display for 5 seconds (when ignition is off). Operating instructions - hands free phone (uconnect™) (if equipped) refer to “hands-free communication (uconnect™)” in section 3 of this manual. Ope...
Page 230
Operating instructions - radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) press the on/vol control to turn the radio on. Press the on/vol a second time to turn off the radio. Electronic volume control the electronic vol...
Page 231
Phone button (uconnect™ hands free phone) — if equipped press this button to operate the hand free phone (ucon- nect™) feature (if equipped). Refer to “hands-free com- munication (uconnect™)” in section 3 for more informa- tion. If your vehicle is not equipped with or this feature is not available o...
Page 232
Rw/ff (radio mode) pressing the rewind or fast forward button causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either am, fm or satellite (if equipped) frequencies. Tune control (radio mode) turn the right side rotary control clockwise to inc...
Page 233
Allow the program format type to be selected. Many radio stations do not currently broadcast music type informa- tion. Toggle the music type button to select the following format types: program type 16 digit-character display no program type or un- defined none adult hits adlt hit classical classicl...
Page 234
By pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the...
Page 235
• angle – repeatedly pressing select will change the viewing angle if supported by the dvd disc (if equipped). Note: the available selections for each of the above entries varies depending upon the disc. Note: these selections can only be made while playing a dvd. • ves power - allows you to turn ve...
Page 236
Audio language — if equipped selecting this item will allow the user to choose a default audio language (effective only if language supported by disc). If customer wishes to select a language not listed, then scroll down and select 9 other. 9 enter the country code using the tune control knob to scr...
Page 237
A disc is loaded, changes will not be effective. Also, the defaults are effective only if the disc supports the customer-preferred settings. Am and fm buttons (radio mode) press the buttons to select am or fm modes. Set button (radio mode) — to set the push-button memory when you are receiving a sta...
Page 238
Operation instructions - (disc mode for cd and mp3/wma audio play, dvd-video) the radio dvd player and many dvd discs are coded by geographic region. These region codes must match in order for the disc to play. If the region code for the dvd disc does not match the region code for the radio dvd play...
Page 239
Eject button — ejecting compact disc(s) press the eject button and the push-button with the corresponding number (1-6) where the cd was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show 9 ejecting disc 9 when the disc is being ejected and prompt the u...
Page 240
Notes on playing mp3/wma files the radio can play mp3/wma files; however, acceptable mp3/wma file recording media and formats are limited. When writing mp3/wma files, pay attention to the following restrictions. Supported media (disc types) the mp3/wma file recording media supported by the radio are...
Page 241
If a disc contains multi formats, such as cd audio and mp3/wma tracks, the radio will only play the mp3/wma tracks on that disc. Supported mp3/wma file formats the radio will recognize only files with the *.Mp3/wma extension as mp3/wma files. Non-mp3/wma files named with the *.Mp3/wma extension may ...
Page 242
Playback of mp3/wma files when a medium containing mp3/wma data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3/wma files. Loading times for playback of mp3/wma files may be affected by the ...
Page 243
Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the user to plug in a portable device such as an mp3/wma player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pu...
Page 244
Operating instructions - satellite radio mode (if equipped) refer to “satellite radio” in this section. Operating instructions - video entertainment system (ves t ) (if equipped) refer to separate “video entertainment system (ves t ) guide.” dolby manufactured under license from dolby laboratories. ...
Page 245
This radio has a hard drive. Cd’s can be ripped to the hard drive, and the map data comes loaded on the hard drive. Refer to your “navigation user’s manual” for detailed operating instructions. Operating instructions — satellite radio refer to your “navigation user’s manual” for detailed operating i...
Page 246
3. Select the appropriate time zone for your location, and press the save soft key to store your selection. Note: when you are traveling and enter a new time zone, the clock must be reset manually for the new zone. Changing daylight savings time 1. Press the time soft key on the lower left side of t...
Page 247
Further information, call the toll-free number 888-539- 7474, or visit the sirius web site at www.Sirius.Com. Please have the following information available when calling: 1. The electronic serial number/sirius identification number (esn/sid). 2. Your vehicle identification number. Electronic serial...
Page 248
Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or under a physical obstacle. • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or alon...
Page 249
3 seconds will make the radio display the song title all of the time (press and hold again to return to normal display). Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) turn the right si...
Page 250
Select the button (1-6) you wish to lock onto this channel and press and release that button. If a button is not selected within 5 seconds after pressing the set button, the channel will continue to play but will not be stored into push-button memory. You may add a second channel to each push-button...
Page 251
4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. Radio operation and cellular phones under certain conditions, t...
Page 252
Mode control the mode control allows you to choose from several pat- terns of air distribution. You can select either a primary mode, as identified by the symbols, or a blend of two of these modes. The closer the control is to a particular mode, the more air distribu- tion you receive from that mode...
Page 253
Defrost air is directed through the windshield and side window demist outlets. Use this mode with maxi- mum fan and temperature settings for best windshield and side window defrosting. Blower control use this control (center rotary knob) to regulate the amount of air forced through the system in any...
Page 254
The instrument panel features four airflow registers. Two registers are located on the outer ends of the instrument panel and two are located in the center of the instrument panel. These registers can be closed to partially block airflow, and they can be adjusted to direct airflow where the occupant...
Page 255
Mix air is directed through the floor, defrost and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. Defrost air is directed through the wi...
Page 256
Temperature control use this control to regulate the temperature of the air in- side the passenger compart- ment. The blue area of the scale indicates cooler tem- peratures while the red area indicates warmer tempera- tures. Note: if your air conditioning performance seems lower than expected, check...
Page 257
Moisture build up inside the vehicle. For maximum defogging, select the outside air position. Note: the “recirculate” mode will not operate in floor, mix or defrost modes. Air conditioning operation press this button to engage the air conditioning. A lamp will illuminate when the air conditioning sy...
Page 258
Smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging. Summer operation air conditioned vehicles must be protected with a high quality antifreeze coolant during summer to provide proper corrosion protection and to raise the boiling point of the coolant...
Page 260: Starting And Operating
Starting and operating contents m starting procedures . . . . . . . . . . . . . . . . . . . . . 263 ▫ manual transmission . . . . . . . . . . . . . . . . . . 263 ▫ automatic transmission . . . . . . . . . . . . . . . . 263 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . . 264 ▫ extreme c...
Page 261
▫ shift positions . . . . . . . . . . . . . . . . . . . . . . . . 280 ▫ shifting procedure . . . . . . . . . . . . . . . . . . . . 281 m trac-lok™ rear axle — if equipped . . . . . . . . . 282 m axle lock (tru–lok™) — rubicon models . . . . . 283 m rear axle lock — 4wd non-rubicon models (if equippe...
Page 262
▫ radial-ply tires . . . . . . . . . . . . . . . . . . . . . . 310 ▫ tire spinning . . . . . . . . . . . . . . . . . . . . . . . . 310 ▫ tread wear indicators . . . . . . . . . . . . . . . . . . 310 ▫ life of tire . . . . . . . . . . . . . . . . . . . . . . . . . 311 ▫ replacement tires . . . . . . ...
Page 263
▫ trailer towing weights (maximum trailer weight ratings) . . . . . . . . . . . . . . . . . . . . . . 334 ▫ trailer and tongue weight . . . . . . . . . . . . . . 337 ▫ towing requirements . . . . . . . . . . . . . . . . . . 338 ▫ towing tips . . . . . . . . . . . . . . . . . . . . . . . . . 343 m re...
Page 264
Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. Manual transmission apply...
Page 265
Normal starting note: normal starting of either a cold or a warm engine is obtained without pumping or depressing the accelerator pedal. Turn the ignition switch to the start position and release when the engine starts. If the engine fails to start within 10 seconds, turn the ignition switch to the ...
Page 266
If engine fails to start warning! • never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. • do not attempt to push or tow your vehicle to get it started. Vehicles equi...
Page 267
Released. If this occurs, continue cranking with the accel- erator pedal pushed all the way to the floor. Release the accelerator pedal and the key once the engine is running smoothly. If the engine shows no sign of starting after two 15 second periods of cranking with the accelerator pedal held to ...
Page 268
Engine block heater — if equipped the engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three wire extension cord. The engine block heater cord is found under the hood bundled in fron...
Page 269
Note: the backup lights will come on when your vehicle is in r (reverse) gear and the ignition is in the on position. Warning! When parking your vehicle, always leave a manual transmission in first gear and apply the parking brake fully to guard against vehicle movement and possible injury or damage...
Page 270
• do not operate at sustained high engine or road speeds in lower gears. Engine damage may result. • do not downshift into a low gear while traveling at too high a speed for that gear. Engine, clutch, or transmis- sion damage may result. • do not rest your foot on the clutch pedal. This causes heat ...
Page 271
Recommended manual transmission downshifting speeds to prevent clutch and transmission damage, your vehicle should be downshifted at speeds no greater than those listed in the chart below: manual transmission downshift speeds in mph (km/h) gear selec- tion 6th to 5th 5th to 4th 4th to 3rd 3rd to 2nd...
Page 272
Automatic transmission caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into p (park) only after the vehicle has come to a complete stop. • shift into or out of r (reverse) only after the vehicle has come to a complete stop and the engine is at i...
Page 273
Shift lock manual override your vehicle may be equipped with a shift lock manual override. The manual override may be used in the event that the shift lever should fail to move from park with the key in the on position and the brake pedal depressed. To operate the shift lock manual override, perform...
Page 274
Brake/transmission interlock system this system prevents you from moving the gear shift out of p (park) and into any gear unless the brake pedal is pressed. This system is active only while the ignition switch is in the on position. Always depress the brake pedal first, before moving the gear select...
Page 275
Gear ranges do not race the engine when shifting from p (park) or n (neutral) position into another gear range. P (park) this gear position supplements the parking brake by locking the transmission. The engine can be started in this range. Never use p (park) while the vehicle is in motion. Apply the...
Page 276
N (neutral) shift into n (neutral) when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Set the parking brake if you must leave the vehicle. Note: towing the vehicle, coasting, or driving for any other reason with selector lever in n (n...
Page 277
Overdrive can be locked out by pressing the o/d off switch located on the center console. The o/d off indicator light (on the switch) will illuminate to show that the switch has been activated. When the indicator light is on, overdrive is locked out. Pressing the switch a second time restores the ov...
Page 278
Caution! • before moving the shift lever out of p (park), you must turn the ignition from lock so the steering wheel and shift lever are released. Otherwise, damage to steering column or shifter could result. • never race the engine with the brakes on and the vehicle in gear, and never hold the vehi...
Page 279
Four–wheel drive operation (command-trac™ or rock-trac™) — if equipped operating instructions/precautions the transfer case provides four mode positions — two (rear) wheel drive high range, four wheel drive high range, neutral, and four wheel drive low range. This transfer case is intended to be dri...
Page 280
Note: do not attempt to make a shift while only the front or rear wheels are spinning. The transfer case is not equipped with a synchronizer and therefore the front and rear driveshafts speeds must be equal for the shift to take place. Shifting while only the front or rear wheels are spinning can ca...
Page 281
Shift positions for additional information on the appropriate use of each transfer case mode position, see the information below: 2h position rear wheel drive high range — normal street and highway driving. Hard surfaced roads. 4h position four wheel drive high range — locks the front and rear drive...
Page 282
Rotate at the same speed. Additional traction and maxi- mum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). The “4wd indicator light” (located in the instrument cluster) will illuminate when the transfer case is shifted into the 4l position. Shifting procedure 2...
Page 283
Warning! Failure to engage a position completely can cause transfer case damage or loss of power and vehicle control. You could have an injury accident. Do not drive the vehicle unless the transfer case is fully engaged. Trac-lok™ rear axle — if equipped the trac-lok™ rear axle provides a constant d...
Page 284
Axle lock (tru–lok™) — rubicon models the axle lock switch is located on the lower switch bank (below the climate controls). This feature will only activate when the following con- ditions are met: • key in ignition, vehicle in 4l (low) range. • vehicle speed should be 10 mph (16 km/h) or less. To a...
Page 285
Rear axle lock — 4wd non-rubicon models (if equipped) the rear axle lock switch is located on the lower switch bank (below the climate controls). This feature will only activate when the following con- ditions are met: • key in ignition, vehicle in 4l (low) range. • vehicle speed should be 10 mph (1...
Page 286
Press the sway bar switch to activate the system. Press the switch again to deactivate the system. The “sway bar indicator light” (located in the instrument cluster) will illuminate when the bar is disconnected. The “sway bar indicator light” will flash during activation transition, or when activati...
Page 287
To disconnect the stabilizer/sway bar, shift to either 4hi or 4lo (refer to “four wheel drive operation” in this section) and press the stabilizer/sway bar button to obtain the off-road position. The amber indicator light will flash until the stabilizer/sway bar has been fully disconnected. Note: th...
Page 288
On-road driving tips utility vehicles have higher ground clearance and a narrower track to make them capable of performing in a wide variety of off-road applications. Specific design characteristics give them a higher center of gravity than ordinary cars. An advantage of the higher ground clearance ...
Page 289
2. Remove one (1) bolt from underside of vehicle. 3. Remove side step assembly. When to use 4l (low) range when off-road driving, shift to 4l (low) for additional traction and control on slippery or difficult terrain, ascending or descending steep hills, and to increase low speed pulling power. This...
Page 290
Caution! When driving through water, do not exceed 5 mph (8 km/h). Always check water depth before entering as a precaution, and check all fluids afterward. Driving through water may cause damage that may not be covered by the new vehicle limited warranty. Driving through water more than a few inche...
Page 291
Driving in snow, mud and sand in heavy snow, when pulling a load, or for additional control at slower speeds, shift the transmission to a low gear and shift the transfer case to 4l (low) if necessary. Refer to “four-wheel drive operation” in this section. Do not shift to a lower gear than necessary ...
Page 292
Remember, never drive diagonally across a hill-always drive straight up or down. If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain forward motion by turning the front wheels slowly left and right. This may provide a fresh “bite” into the surface a...
Page 293
• after extended operation in mud, sand, water, or similar dirty conditions, have brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have ...
Page 294
Note: the instrument cluster “brake warning light” indicates only that the parking brake is applied. You must be sure the parking brake is fully applied before leaving the vehicle. Be sure the parking brake is firmly set when parked, and the gear shift lever is in the p (park) position (automatic tr...
Page 295
Warning! • always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury. Also, be certain to leave an automatic transmission in p (park), a manual transmission in r (reverse) or 1st gear. Failure to do so may allow the vehicle to roll and cause damage o...
Page 296
The anti-lock brake system conducts a low speed self- test at about 12 mph (20 km/h). If for any reason, your foot is on the brake when the vehicle reaches 12 mph (20 km/h), this check will be delayed until 25 mph (40 km/h). The anti-lock brake system pump motor runs during the self-test and during ...
Page 297
Warning! • anti-lock system (abs) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • the abs cannot prevent accidents, including th...
Page 298
If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these condi- tions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers. Note: increased noise levels at the end of th...
Page 299
Tire safety information tire markings note: • p(passenger)-metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designation. Ex- ample: p215/65r15 95h. • european metric tire sizing is based on european design standards....
Page 300
Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ( ....Blank.... ( = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = s...
Page 301
Example: service description: 95 = load index —a numerical code associated with the maximum load a tire can carry. H = speed symbol —a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —the maximum speed corresp...
Page 302
Tire identification number (tin) the tin may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full tin including date code located on the white sidewall side of the tire. Look for the tin on the outboard side of black s...
Page 303
Tire loading and tire pressure tire placard location tire placard location (2 door models) tire placard location (4 door models) 302 starting and operating.
Page 304
Tire and loading information placard this placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare...
Page 305
Combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for determining correct load limit 1. Locate the statement “the combined weight of occu- pants and cargo should never exceed xxx pounds” on your vehicle’s placa...
Page 306
Starting and operating 305 5.
Page 307
Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...
Page 308
2. Economy— improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consump- t...
Page 309
The pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated eve...
Page 310
Tire pressures change by approximately 1 psi (7 kpa) per 12° f (7° c) of air temperature change. Keep this in mind when checking tire pressure inside a garage especially in the winter. Example: if garage temperature = 68° f (20° c) and the outside temperature = 32° f (0° c) then the cold tire inflat...
Page 311
Radial-ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial tires in sets of four. Never combine them with other types of tires. Cuts and punctures in radial tire...
Page 312
These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point. Life of tire...
Page 313
Keep unmounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease and gasoline. Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold ti...
Page 314
Caution! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Alignment and balance poor suspension alignment may result in: • fast tire wear. • uneven tire wear, such as feathering and one-sided wear. • vehicle pull to right or left. Tires m...
Page 315
• install chains snugly and tighten after.6 mile (1 km) of driving. • do not exceed 30 mph (48 km/h). • drive cautiously, avoiding large bumps, potholes and extreme driving maneuvers. Tire rotation recommendations tires on the front and rear axles of vehicles operate at different loads and perform d...
Page 316
Tire pressure monitor system (tpms) the tire pressure monitoring system (tpms) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. The tire pressure will vary with temperature by about 1 psi (6.9 kpa) for every 12°f (6.5°c). This means that when the ou...
Page 317
The measured tire pressure is 30 psi (207 kpa), a tempera- ture drop to 20°f (-7°c) will decrease the tire pressure to approximately 26 psi (179 kpa). This tire pressure is sufficiently low enough to turn on the “tire pressure monitoring telltale light.” driving the vehicle may cause the tire pressu...
Page 318
Caution! After inspecting or adjusting the tire pressure always reinstall the valve stem cap. This will prevent mois- ture and dirt from entering the valve stem, which could damage the tire pressure monitoring sensor. Note: • the tpms is not intended to replace normal tire care and maintenance, nor ...
Page 319
Note: it is particularly important, for you to check the tire pressure in all of your tires regularly and to maintain the proper pressure. The tire pressure monitor system (tpms) consists of the following components: • receiver module • 4 tire pressure monitoring sensors • tire pressure monitoring t...
Page 320
1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the tpm sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the ve...
Page 321
And reinstall it on the vehicle in place of the spare tire, the tpms will update automatically and the “tire pressure monitoring telltale light” will turn off, as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven ...
Page 322
Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required. Poor quality gasoline can cause problems such as hard starting, stalling and hesitations. If you experience these symptoms, tr...
Page 323
Caution! Do not use gasolines containing methanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components. Problems that result from using methanol/gasoline blends are not the responsibility of the manufacturer. While mtbe is an oxygenate ...
Page 324
Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gasoline is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance, damage the emission control system. • an out-of-tune engine, or certain fuel or ignition mal...
Page 325
Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such ...
Page 326
Adding fuel fuel filler cap (gas cap) the gas cap is located on the driver’s side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. Caution! Damage to the fuel system or emission control sys- tem could result from using an improper fuel cap ...
Page 327
Caution! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. Note: when the fuel nozzle “clicks” or shuts off, the fuel tank is full. Warning! • never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • never add f...
Page 328
Caution! Damage to the fuel system or emission control sys- tem could result from using an improper fuel tank filler cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Vehicle loading certification label as required by national highway traffic safety admin- istration regu...
Page 329
Gross axle weight rating (gawr) the gawr is the maximum permissible load on the front and rear axles. The load must be distributed in the cargo area so that the gawr of each axle is not exceeded. Each axle gawr is determined by the components in the system with the lowest load carrying capacity (axl...
Page 330
Then be determined separately to be sure that the load is properly distributed over front and rear axle. Weighing the vehicle may show that the gawr of either the front or rear axles has been exceeded but the total load is within the specified gvwr. If so, weight must be shifted from front to rear o...
Page 331
Common towing definitions the following trailer towing related definitions will assist you in understanding the following information: gross vehicle weight rating (gvwr) the gvwr is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load ...
Page 332
Tongue weight (tw) the downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle. Frontal area the maximum height and maximum width of the front of a trailer. ...
Page 333
Warning! An improperly adjusted weight distributing hitch system may reduce handling, stability, braking per- formance, and could result in an accident. Weight distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable recrea...
Page 334
Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the trailer towing weights (maximum ...
Page 335
Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmis- sion axle model gcwr (gross combined wt. Rat- ing) frontal area max. Gtw (gross trailer wt.) max. Tongue wt. (see note 1) 3.8l/...
Page 336
3.8l/ automatic 4.10 2 door rubicon model (4wd) 6,281 lbs (2 849 kg) 25 sq. Ft. (2.32 square meters) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.8l/ manual 3.21 4 door x model (2wd) 5,121 lbs (2 323 kg) 32 sq. Ft. (2.97 square meters) 1,000 lbs (453 kg) 100 lbs (45 kg) 3.8l/ manual 3.73 4 door x model (2wd...
Page 337
3.8l/ automatic 3.73 4 door x model (4wd) 7,825 lbs (3 549 kg) 32 sq. Ft. (2.97 square meters) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.8l/ manual 3.21 4 door sahara model (4wd) 5,481 lbs (2 486 kg) 32 sq. Ft. (2.97 square meters) 1,000 lbs (453 kg) 100 lbs (45 kg) 3.8l/ manual 3.73 4 door sahara mod...
Page 338
Trailer and tongue weight always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the gross trailer weight (gtw) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to s...
Page 339
Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the tire and loading information plac- ard in the “tire— safety ...
Page 340
Warning! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that...
Page 341
• total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. Gvwr 2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitch utilized (this requirement may limit the ability to always achieve the 10% to 15% range of tongue wei...
Page 342
Towing requirements — trailer brakes − do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. − an electronically actuated trailer brake controller is required when towing a trailer w...
Page 343
Warning! Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- tem and cause it to fail. You might not have brakes when you need them and could have an accident. Towing any trailer will increase your stopping dis- tance. When towing you should allow...
Page 344
Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in 1st gear to avoid excessive clutch slippage. Towing tips — automatic transmission the “d” ...
Page 345
Towing tips — electronic speed control (if equipped) − don’t use in hilly terrain or with heavy loads. − when using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. − use speed control in flat terrain and with light l...
Page 346
Towing – 4wd models note: the transfer case must be shifted into n (neu- tral) for recreational towing. Shifting into neutral (n) use the following procedure to prepare your vehicle for recreational towing. Caution! It is necessary to follow these steps to be certain that the transfer case is fully ...
Page 347
Caution! Damage to the transmission may occur if the trans- mission is shifted into p (park) with the transfer case in n (neutral) and the engine running. With the transfer case in n (neutral) ensure that the engine is off prior to shifting the transmission into p (park) (refer to steps 7 – 8 above)...
Page 348
Caution! • do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. Starting and operating 347 5.
Page 350: Contents
What to do in emergencies contents m hazard warning flashers . . . . . . . . . . . . . . . . . 350 m if your engine overheats . . . . . . . . . . . . . . . . . 351 m jacking and tire changing . . . . . . . . . . . . . . . . 352 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . . 352 ▫ sp...
Page 351
Hazard warning flashers your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicl...
Page 352
If your engine overheats in any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • on the highways — slow down. • in city traffic — while stopped, put transmission in n (neutral), but do not increase engine idle speed. Note: there are step...
Page 353
Jacking and tire changing warning! • getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center wh...
Page 354
Spare tire stowage to remove the spare tire from the carrier, remove the tire cover, if equipped, and remove the lug nuts with the lug wrench turning them counterclockwise. Note: if you have added aftermarket accessories to the spare tire mounted carrier, it cannot exceed a gross weight of 50 lbs (2...
Page 355
4. Operate jack from the front or the rear of the vehicle. Place the jack under the axle tube, as shown. Do not raise the vehicle until you are sure the jack is fully engaged. 5. Raise the vehicle by turning the jack screw to the right. Raise the vehicle only until the tire just clears the surface a...
Page 356
7. Position spare wheel/tire on vehicle and install lug nuts with cone-shaped end toward wheel. Lightly tighten nuts clockwise. To avoid the risk of forcing the vehicle off the jack, do not tighten the nuts fully until the vehicle has been lowered. 8. Lower the vehicle by turning the jack screw to t...
Page 357
Warning! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush contaminated area immediately with large quantities of ...
Page 358
5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. 6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, t...
Page 359
Emergency tow hooks — if equipped if your vehicle is equipped with tow hooks, they are mounted in the front and the rear. Caution! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. ...
Page 360: Maintaining Your Vehicle
Maintaining your vehicle contents m engine compartment – 3.8l . . . . . . . . . . . . . . . 362 m onboard diagnostic system — obd ii . . . . . . . . 363 ▫ loose fuel filler cap message . . . . . . . . . . . . 364 m emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . ....
Page 361
▫ driveline and steering component lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . 376 ▫ body lubrication . . . . . . . . . . . . . . . . . . . . . 376 ▫ windshield wiper blades . . . . . . . . . . . . . . . . 376 ▫ windshield and rear window washers . . . . . 377 ▫ exhaust system . ...
Page 362
M fluid capacities . . . . . . . . . . . . . . . . . . . . . . . . 408 m fluids, lubricants and genuine parts . . . . . . . . 409 ▫ engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 ▫ chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410 maintaining your vehicle 361 ...
Page 363
Engine compartment – 3.8l 362 maintaining your vehicle.
Page 364
Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...
Page 365
Loose fuel filler cap message after fuel is added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improp- erly installed, or damaged. A loose fuel filler cap message will be displayed in the instrument cluster. Tighten the gas cap until a 9 clicking 9 sound is ...
Page 366
Your vehicle has a simple ignition key actuated test, which you can use prior to going to the test station. To check if your vehicle’s obd system is ready, you must do the following: 1. Insert your ignition key into the ignition switch. 2. Turn the ignition to the on position, but do not crank or st...
Page 367
Vehicle serviced before going to the i/m station. The i/m station can fail your vehicle because the mil symbol is on with the engine running. Replacement parts use of genuine mopar t parts for normal/scheduled maintenance and repairs is highly recommended to in- sure the designed performance. Damage...
Page 368
Maintenance procedures the pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maint...
Page 369
Caution! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. Change engine oil refer to the maintenance schedule for recommended engine oil change intervals. Engine oil selection for best performance and maximum protection for all eng...
Page 370
The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to the “engine com- partment” illustration in this section. Lubricants which do not have both, the engine oil certi- fication mark and the correct sae v...
Page 371
Drive belts — check condition and tension belt tension is controlled by means of an automatic tensioner. No belt tension adjustments are required. However, belt and belt tensioner condition should be inspected at the specified intervals, and replaced if re- quired. See your authorized dealer for ser...
Page 372
Caution! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your veh...
Page 373
To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires dis...
Page 374
Engine air cleaner filter refer to the maintenance schedule for recommended engine air cleaner filter change intervals. Warning! The air cleaner can provide protection in the case of engine backfire. Do not remove the air cleaner unless it is necessary for repair or maintenance. Make sure that no on...
Page 375
Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at thi...
Page 376
Note: use only manufacturer approved a/c system sealers, stop leak products, seal conditioners, compres- sor oil, and refrigerants. Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluorocar- bon (hfc) that is endorsed by the environmental pro- tection agency and is a...
Page 377
Driveline and steering component lubrication all driveline and steering components are sealed and do not require lubrication. Driveshafts are not serviceable. Body lubrication locks and all body pivot points, including such items as seat tracks, doors, tailgate and hood hinges, should be lubricated ...
Page 378
Windshield and rear window washers the fluid reservoir for the windshield washers and the rear window washer (if equipped) is shared. The fluid reservoir is located in the engine compartment, be sure to check the fluid level at regular intervals. Fill the reservoir with windshield washer solvent onl...
Page 379
Into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubri- cation or oil change. Replace as required. Cooling system warning! You or others can be badly burned by hot antifreeze/ coolant or steam from your radiator. If you see or hear steam com...
Page 380
Cooling system — drain, flush, and refill at the intervals shown on the maintenance schedule, the system should be drained, flushed and refilled. If the solution is dirty and contains a considerable amount of sediment, clean and flush with reliable cooling system cleaner. Follow with a thorough rins...
Page 381
Adding engine coolant your vehicle has been built with an improved antifreeze/ coolant that allows extended maintenance intervals. This antifreeze/coolant can be used up to 5 years or 100,000 miles (160 000 km) before replacement. To prevent reduc- ing this extended maintenance period, it is importa...
Page 382
The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. Warning! The warning words do not open hot on the cooling system pressure cap are a safety precaution. Never add antifreeze/coolant when the engine is overheated. Do not loosen or remove...
Page 383
When additional antifreeze/coolant is needed to main- tain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicle is stopped after a few miles of operation, you may observe vapor coming from the front of the engine compartment. This is ...
Page 384
Only the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mileage, and increased emissions. Hoses and vacuum/vapor harnesses inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber, cra...
Page 385
Brake and power steering system hoses when servicing the vehicle for scheduled maintenance, inspect surface of hoses for evidence of heat and me- chanical damage. Hard and brittle rubber, cracking, tears, cuts, abrasion, and excessive swelling suggest deteriora- tion of the rubber. Particular attent...
Page 386
Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter or moisture. Caution! Do not allow petroleum base fluid to contaminate the brake fluid. Seal damage will result. Automatic transmission selection of lubricant it is important that the proper l...
Page 387
To properly check the automatic transmission fluid level, the following procedure must be used: 1. Operate the engine at idle speed and normal operating temperature. 2. The vehicle must be on level ground. 3. Fully apply parking brake. 4. Place the gear selector momentarily in each gear position end...
Page 388
Caution! Be aware that if the fluid temperature is below 50° f (10° c), it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. 7. Check for leaks. Release the parking brake. Note: to prevent dirt and water from entering the tran...
Page 389
Fluid level check check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more than 3/16” (4.76 mm) below the bottom of the hole. Add fluid, if necessary, to maintain the proper level. Frequency of fluid change under normal opera...
Page 390
Drain first remove fill plug (b), then drain plug (c). Recom- mended tightening torque for drain and fill plugs is 15–25 ft.Lbs. (20–34 n·m). Caution! When replacing plugs, do not overtighten. You could damage them and cause them to leak. Selection of lubricant use only manufacturer’s recommended fl...
Page 391
Following off-road usage, completely inspect the under- body of your vehicle. Check tires, body structure, steer- ing, suspension and exhaust system for damage. Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering and suspension. Retighten, if required...
Page 392
Hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- body protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What causes corrosion? Corrosion i...
Page 393
Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8 274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty...
Page 394
Wheel and wheel trim care all wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil, use mopar t wheel cleaner or select a non- abrasive, non-acidic cleaner. Do not use scouring pads, stee...
Page 395
Warning! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Caution! When installing hanging air fresheners in your ve- hicle, read the installation instructions carefully. Some air fresheners will damage t...
Page 396
Seat belt maintenance do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use mopar t total clean, a mild soap solution, or lukewarm water. Do not remove the belts from the...
Page 397
Rinsing — be sure to remove all trace of cleaner by rinsing the top thoroughly with clean water. Remember to allow the top to dry before lowering it. Care of fabric top windows caution! Your vehicle’s fabric top has pliable plastic windows which can be scratched unless special care is taken by follo...
Page 398
Halves with fresh water and allow to dry. Aggressively work the mopar t soft top zipper cleaner and lubricant into the zipper teeth. If a stuck zipper slide is experi- enced, work the mopar t soft top zipper cleaner and lubricant into the zipper slide. Several applications may be required before the...
Page 399
Cavity cartridge fuse mini fuse description j4 25 amp natural driver door node j5 25 amp natural passenger door node j6 40 amp green anti-lock brake sys- tem (abs) pump feed/esp j7 30 amp pink anti-lock brake sys- tem (abs) valve feed/esp j8 — — j9 40 amp green pzev sec motor feed/flex fuel j10 30 a...
Page 400
Cavity cartridge fuse mini fuse description j21 20 amp yellow front/rear washer j22 — spare m1 15 amp blue center high mounted stop light (chmsl)/ switch stop lamp feed m2 20 amp yellow relay trailer lighting (stop) m3 20 amp yellow frt/rear axle locker relay m4 — — m5 — — m6 20 amp yellow power out...
Page 401
Cavity cartridge fuse mini fuse description m11 10 amp red (ignition off draw) iod-hvac/atc, mw sensr, under- hood lamp (uh lmp) m12 30 amp green amplifier (amp) m13 20 amp yellow ignition off draw— cabin compartment node (iod-ccn), wireless control mod- ule (wcm), siren, multi-function con- trol sw...
Page 402
Cavity cartridge fuse mini fuse description m16 10 amp red occupant restraint controller (orc) m17 15 amp blue left tail/license/ park lamp (lt-tail/ lic/prk lmp) m18 15 amp blue right tail/park/run lamp (rt-tail/ prk/run lmp) m19 25 amp natural auto shut down (asd #1 and #2) m20 15 amp blue cabin c...
Page 403
Cavity cartridge fuse mini fuse description m30 15 amp blue wiper motor frt, j1962 diagnostic feed m31 20 amp yellow back-up lamps (b/u lamps) m32 10 amp red occupant restraint controller (orc), tt europe m33 10 amp red next generation con- troller (ngc), global powertrain engine controller (gpec) m...
Page 404
Caution! • when installing the integrated power module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the integrated power module, and possibly result in a electrical system failure. • when replacing a blown fuse, i...
Page 405
Replacement bulbs — if equipped interior lights bulb type auto. Trans. Indicator light . . . . . . . . . . . . . . . . . 658 courtesy lights, under dash (1) . . . . . . . . . . . . . . 906 heater control lights (2) . . . . . . . . . . . . . . . . . . . 194 rocker switch indicator light (rear window ...
Page 406
Bulb replacement head light 1. Open hood and support using prop rod. 2. Remove the front grille. Turn the retainers along the top 1/4 turn counter-clockwise and remove. 3. Pull the bottom of the grille away starting at one side and working toward the other. 4. Turn both park and turn signal socket a...
Page 407
Front park/turn signal 1. Remove the front grille. Turn the retainers along the top 1/4 turn counter-clockwise and remove. 2. Pull the bottom of the grille away starting at one side and working toward the other. 3. Turn the socket assembly 1/4 turn counter-clockwise and remove from housing. Pull the...
Page 408
Rear tail, stop, turn signal, and back-up lights 1. Remove the two (2) inboard screws attaching the tail light housing to the body. Do not remove the outer screws at any time. 2. Separate the housing from the body by pushing the lamp inboard while pulling the lamp away from the body. 3. Rotate the a...
Page 409
Fluid capacities u.S. Metric fuel (approximate) — 2 door models 18.5 gallons 70 liters fuel (approximate) — 4 door models 22.5 gallons 85 liters engine oil with filter 3.8 liter engine (sae 5w-20, api certified engine oil) 6 quarts 5.7 liters cooling system * 3.8 liter engine (mopar t antifreeze/eng...
Page 410
Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar t antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid or- ganic additive technology) engine oil use api certified sae 5w-20 engine oil, meeting the requirements of daimlerchrysler mat...
Page 411
Chassis component fluid, lubricant, or genuine part automatic transmission mopar t atf+4 automatic transmission fluid manual transmission mopar t manual transmission lubricant or equivalent (meeting the require- ments of daimlerchrysler material standard ms-9224) transfer case mopar t atf+4 automati...
Page 412: Maintenance Schedules
Maintenance schedules contents m emission control system maintenance . . . . . . . . 412 m maintenance schedule . . . . . . . . . . . . . . . . . . . 412 ▫ required maintenance intervals . . . . . . . . . . . 415 8 m a i n t e n a n c e s c h e d u l e s.
Page 413
Emission control system maintenance the “scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done t...
Page 414
• change your engine oil more often if you drive your vehicle off-road for an extended period of time. • under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or 6 months, whichever comes first. Your dealer will reset the oil change indicator message after completing the ...
Page 415
Once a month • check tire pressure and look for unusual wear or damage. • inspect the battery and clean and tighten the terminals as required. • check the fluid levels of coolant reservoir, brake master cylinder, power steering and transmission and add as needed. • check all lights and other electri...
Page 416
Required maintenance intervals perform maintenance every (where time and mileage are listed, follow the interval that occurs first.) maintenance items miles kilometers or months change the engine oil and engine oil filter. 6,000 10 000 6 rotate tires. 6,000 10 000 6 if using your vehicle for any of ...
Page 417
Perform maintenance every (where time and mileage are listed, follow the interval that occurs first.) maintenance items miles kilometers or months inspect the front suspension, tie rod ends and boot seals, replace if necessary. 24,000 40 000 24 replace the engine air cleaner filter. 30,000 50 000 30...
Page 418
Perform maintenance every (where time and mileage are listed, follow the interval that occurs first.) maintenance items miles kilometers or months change the automatic transmission fluid & main sump filter if using your vehicle for any of the follow- ing: police, taxi, fleet or frequent trailer towi...
Page 419
Warning! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. 418 maintenance schedules 8 m a i ...
Page 420: Contents
If you need consumer assistance contents m suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420 ▫ prepare for the appointment . . . . . . . . . . . . 420 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . 420 ▫ be reasonable...
Page 421
Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. ...
Page 422
Technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • if for some reason you are still not satisfied, talk t...
Page 423
Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer who has access to a tdd ...
Page 424
Warning! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of california to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain prod- ucts of component wear contai...
Page 425
To contact nhtsa, you may either call the auto safety hotline toll free at 1–888–327–4236 (tty: 1–800–424– 9153), or go to http://www.Safercar.Gov; or write to: administrator, nhtsa, 400 seventh street, sw., wash- ington, dc 20590. You can also obtain other information about motor vehicle safety fro...
Page 426
• diagnostic procedure manuals. Filled with diagrams, charts and detailed illustrations, these practical manuals make it easy for students and technicians to find and fix problems on computer- controlled vehicle systems and features. They show exactly how to find and correct problems the first time,...
Page 427
Department of transportation uniform tire quality grades the following describes the tire grading categories estab- lished by the national highway traffic safety adminis- tration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on ...
Page 428
Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the materi...
Page 430: Index
Index 10
Page 431
Abs (anti-lock brake system) . . . . . . . . . . . . 202,294 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 325 adding washer fluid . . . . . . . . . . . . . . . . . . . . . 192 air cleaner, engine (engine air cleaner filter) . . . 373 air conditioner maintenance . . . . . . . . ....
Page 432
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373 emergency starting . . . . . . . . . . . . . . . . . . . . . 355 keyless transmitter replacement (rke) . . . . . . . 23 belts, drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 belts, seat . . . . . . . . . . ....
Page 433
Child restraint . . . . . . . . . . . . . . . . . . . . 58,59,65,68 child restraint tether anchors . . . . . . . . . . . . . 64,65 child seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 climate control . . . . . . . . . . . . . . . . . . . . . . . . . 250 clock . . . . . . . . . ....
Page 434
Dipsticks oil (engine) . . . . . . . . . . . . . . . . . . . . . . . . . . 367 disabled vehicle towing . . . . . . . . . . . . . . . . . . . 358 disarming, theft system . . . . . . . . . . . . . . . . . . . 18 disposal engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 369 used coolant...
Page 435
Air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 373 block heater . . . . . . . . . . . . . . . . . . . . . . . . . 267 break-in recommendations . . . . . . . . . . . . . . . . 71 compartment . . . . . . . . . . . . . . . . . . . . . . . . . 362 compartment identification . . . . . . ...
Page 436
Flooded engine starting . . . . . . . . . . . . . . . . . . . 265 fluid capacities . . . . . . . . . . . . . . . . . . . . . . . . . 408 fluid level checks . . . . . . . . . . . . . . . . . . . . . . 389 automatic transmission . . . . . . . . . . . . . . . . . 385 engine oil . . . . . . . . . . . . ...
Page 437
Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . 200 tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 203 gear ranges . . . . . . . . . . . . . . . . . . . . . . . . 269,274 general information . . . . . . . . . . . . . . . . . . . . 17,320 glass cleaning . . . . . . . . ....
Page 438
Inside rearview mirror . . . . . . . . . . . . . . . . . . . . 79 instrument cluster . . . . . . . . . . . . . . . . . . . . . . . 199 instrument panel and controls . . . . . . . . . . . . . . 198 instrument panel lens cleaning . . . . . . . . . . . . . 394 integrated power module (fuses) . . . . . ...
Page 439
Check engine (malfunction indicator) . . . . . . . . 207 cruise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 daytime running . . . . . . . . . . . . . . . . . . . . . . . 94 dimmer switch, headlight . . . . . . . . . . . . . . . . 93 electronic stability program (esp) indicator . ...
Page 440
Lower anchors and tether for children (latch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64,65 lubrication, body . . . . . . . . . . . . . . . . . . . . . . . 376 maintenance free battery . . . . . . . . . . . . . . . . . . 373 maintenance procedures . . . . . . . . . . . . . . . . . . ...
Page 441
Dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367 filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369 identification logo . . . . . . . . . . . . . . . . . . . . . 368 materials added to . . . . . . . . . . . . . . . . . . . . . 369 pressure warning light . ...
Page 442
Radio, navigation . . . . . . . . . . . . . . . . . . . . . . . 243 radio operation . . . . . . . . . . . . . . . . . . . . . . . . 250 radio, satellite . . . . . . . . . . . . . . . . . . . . . . . 244,245 rear axle (differential) . . . . . . . . . . . . . . . . . . . . 389 rear swing gate . . . . ...
Page 443
Safety tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 satellite radio . . . . . . . . . . . . . . . . . . . . . . . 244,245 satellite radio antenna . . . . . . . . . . . . . . . . . . . 246 schedule, maintenance . . . . . . . . . . . . . . . . . . . . 412 seat belt reminder . . . ...
Page 444
Automatic transmission . . . . . . . . . . . . . . . . . 273 manual transmission . . . . . . . . . . . . . . . . . . . 267 shoulder belt upper anchorage . . . . . . . . . . . . . . 44 shoulder belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 side airbag . . . . . . . . . . . . . . . . ...
Page 445
Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 temperature gauge, engine coolant . . . . . . . . . . 203 tether anchor, child restraint . . . . . . . . . . . . . . . 64 theft system arming . . . . . . . . . . . . . . . . . . . . . . 18 theft system disarming . . . . . . . . ....
Page 446
Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334 recreational . . . . . . . . . . . . . . . . . . . . . . . . . . 344 weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334 trac-lok rear axle . . . . . . . . . . . . . . . . . . . . . . 282 traction control . . . ...
Page 447
Vacuum/vapor harnesses . . . . . . . . . . . . . . . . . 383 vehicle identification number (vin) . . . . . . . . . . . . 8 vehicle loading . . . . . . . . . . . . . . . . . . . . . . 303,327 vehicle modifications/alterations . . . . . . . . . . . . . . 8 vehicle storage . . . . . . . . . . . . . . ....
Page 448
Wrangler o w n e r ’ s m a n u a l 2 0 0 8 2 0 0 8 w ra n g le r 81-326-0855 first edition printed in u.S.A..