KAM KCD3000 USB Instruction Manual - page 4
11. PROG: The maximum number of tracks that can be edited is 99.
PROG has three views – Program Editing, Program Track Viewing, and Program Play.
Start PROG-Edit:
In pause mode, press this button to edit a program. This view is called PROG Editing.
The display MM:SS:FF will show “P-xx” and then “xx” will flash.
Select a track by pressing SKIP (for CD or MP3) or Folder-SKIP (only MP3) and then press the PROG button to store it.
Repeat the same process for each track and finally press the PROG button again to finish editing a program.
The unit will go into PROG Track Viewing mode and allow you to review each track by pressing SKIP.
Play PROG:
Press PLAY/PAUSE to play the program. PROG will flash in the display.
Exit PROG Play/Edit:
When the PROG playback is paused, pressing the PROG button for two seconds will return to normal playback.
Once returned to normal playback, pressing the PROG button will enter the program again and you can continue the track editing
from the last PROG track number.
In PROG Editing view, pressing the PROG button for 2 seconds will wipe out the PROG list and return to normal playback.
12. PITCH: Press it to switch the pitch range. It will switch between 8%, 16%, and 100% and off mode.
13. PITCH CONTROL SLIDER: By moving the pitch control slider, you can adjust it between minimum (up) and maximum (down)
to match the beat of the two playing units.
14. RELAY: Press it to activate this function. When one unit is in play mode, and the other unit is in pause mode; pause the
playing unit, the other unit will automatically start to play.
15. SEARCH: Press the search button to activate fast search mode. Use Jog Wheel to do the fast search forward and backward.
16. CUE: The cue function allows the CD to be played from a memorized point.
17. SEAMLESS LOOP: There is A, B, and RELOOP buttons.
The A button is the start point of the LOOP. The end point is button B. Press the A and B button to set up the point and start the
loop playback automatically. The loop lights up on the display and the three LEDs will flash.
Press B again to exit the LOOP playback.
The RELOOP button will return to the A of the loop playback and continues playing. Also, if you want to return to the loop
playback after exiting, you can press the RELOOP button.
Change the start and end points by pressing the A and B buttons again.
Auto loop
There is also an auto loop function to assist in obtaining seamless loops. Press and hold the MEMO button, then using the jog
wheel to adjust the loop recording range from 1/32~32/1. The memo button will stay illuminated and this will show that the auto
loop function is ready, to start the loop press the A button at the desired point and the loop recording will begin and automatically
record only for the preset time you chose, this is measured in bars e.g. 1/1 equals one bar or 4 beats the recorded loop is still
editable using the loop edit function
18. PLAY/PAUSE: Pressing this button will cause the operation to change between PLAY and PAUSE modes.
19. PITCH BEND: Using this function, the speed can be changed to keep up with the other playing one.
20. TRACK/TRIM: This button selects the track to be played and can skip forward or backward one track.
*TRIM: In loop playback, press it to enlarge or shorten the loop length double.
21. BPM/TAP: Use it to switch between Auto BPM and Manual BPM. In manual mode, press it with the beat to get the BPM
value. The value will calculate and change by 4 times tapping.
22. MT: When this function is activated, the key of the song will be locked even though the pitch fader is adjusted.
23. CONNECTION PORTS: Connect from this port to the main unit.
The port has to be connected correctly to its relative port and both ports (A&B) have to be connected to activate all functions.